SIIG AV-GM09M3-S1 User manual

16x4 3G/HD/SD-SDI Switch
P/N: AV-GM09M3-S1

Safety and Notice
The AV-GM09M3-S1 16x4 3G/HD/SD-SDI Switch has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like all
electronic equipments, the AV-GM09M3-S1 should be used with care. Please read and follow
the safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
●Follow all instructions and warnings marked on this unit.
●Do not attempt to service this unit yourself, except where explained in this manual.
●Provide proper ventilation and air circulation and do not use near water.
●Keep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
●Use only the power adapter and power cords and connection cables designed for this unit.
●Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
TABLE OF CONTENTS
INTRODUCTION.................................................................................................................1
FEATURES.........................................................................................................................1
PACKAGE CONTENTS ......................................................................................................1
SPECIFICATIONS ..............................................................................................................2
PANEL DESCRIPTIONS.....................................................................................................4
HARDWARE INSTALLATION.............................................................................................5
CONNECTION DIAGRAM...................................................................................................5
IR REMOTE CONTROL......................................................................................................6
WARRANTY........................................................................................................................6

1
INTRODUCTION
The AV-GM09M3-S1 16x4 3G/HD/SD-SDI Switch receives, equalizes, and reclocks* up to 16 SDI
inputs, perfectly switches the desired input to SDI equipped monitors or receivers. The switch
supports both HD/SD-SDI bit rates, and the re-transmitted quality is guaranteed. Through RS-232,
IR remote, or front panel push button, the control of the SDI switch becomes versatile and easier.
AV-GM09M3-S1 offers the most convenient and cost effective means for swift switch and
duplication of high quality SDI in the market.
FEATURES
●3G / HD / SD-SDI switch
●Up to 16 input & 4 re-timing SDI outputs
●Dual color indication LED of 3G / HD / SD of the output SDI
●Automatic detection of the SDI Input
●Synchronizes input/output (switch after vertical sync)
●Provides the equalized and reclocked* transmission path up to 300m (1000ft) at SD-SDI , 150m
(500ft) at HD-SDI or 100m (500ft) at 3G HD-SDI
●Multiple control by RS-232, IR remote, and push button
PACKAGE CONTENTS
●1 x AV-GM09M3-S1
●1 x Rack-mounting ear set
●1 x DC 5V 4A in-line with C7 power cord
●1 x User Manual
* A Reclocking feature first equalizes, then extracts a clock from the signal and cleans up the
eye pattern. It is useful to avoid signal loss due to cable length

2
SPECIFICATIONS
Model Name
AV-GM09M3-S1
Technical
Role of usage
16x4 switch
SDI standards
SD-SDI, HD-SDI & 3G-SDI
Auto 3G/HD/SD
detection
Yes
Supported protocols
SMPTE 259M (270Mbps / 360Mpbs)
SMPTE 292M / HDTV (1.485 & 1.485/1.001Gbps)
SMPTE 424/425M (2.97 & 2.97/1.001Gbps)
Video bandwidth
2.97Gpbs
Data rates
143 / 270 / 1483 / 1485 / 2967 / 2970 Mbps
Video support
[3G] 1080p@50/59.94/60 (4:2:2)
[HD] 720p50/59.94/60, 1080p24/30, 1035i50/59.94/60, 1080i50/59.94/60
[SD] [email protected]Hz, PAL@50Hz
Output impedance
75Ω
Reclocking function
Optional upon request
Cable equalization
[HD-SDI] up to 150m (500ft)
[SD-SDI] up to 300m (1000ft)
Loop-out
Synchronized BNC loop-out at input and output
Audio support
Yes
RP-198 pathological
patterns
Immune
PCB stack-up
4-layer board [impedance control X differential 100Ω; single 50Ω]
Input
16x BNC [SDI]
Output
4x BNC [SDI]
BNC connector
75Ωinter-locked socket
Eye pattern
characteristics
(HD-SDI)
Amplitude: Within 800mV 3% (<10%) Long time jitter: 0.195 UI (<1.0
UI)
Rise overshoot: Less than 2% (<10%) Timing jitter: 0.195 UI (<1.0 UI)
Fall overshoot: Less than 2% (<10%) Alignment jitter: 0.127 UI (<0.2
UI)

3
Mechanical
Housing
Metal enclosure
Dimensions
[L x W x H]
Model
440 x 125 x 43mm [1'5.3" x 4.9" x 1.7"]
Package
510 x 230 x 70mm [1'8" x 9.1" x 2.8"]
Carton
510 x 410 x 252mm [1'8" x 1'4" x 10"]
Weight
Model
TBA
Package
TBA
Fixedness
Latch-locking power supply
Power supply
5V 4A DC
Power consumption
10 Watt [max]
Operation temperature
0~40°C [32~104°F]
Storage temperature
-20~60°C [-4~140°F]
Relative humidity
20~90% RH [no condensation]
The measurement results are from Tektronix VFM-700 with SDI through 1m (3.3ft) long
Belden 1694A.

4
PANEL DESCRIPTIONS
Front Panel
1.Button: Input source selection
2.Green LED: SD signal indicator
3.Red LED: 3G / HD signal indicator
4.IR: IR sensor
5.3.5mm: IR receiver
Rear Panel
6.Power: On/off switch
7.Power: +5V DC latch-locking
8.RS-232: Serial channel control
9.BNC: Synchronized signal input
10.BNC: Synchronized serial output (add 75Ω terminator if not connect)
11.BNC: SDI output
12.BNC: SDI input

5
HARDWARE INSTALLATION
1. Connect one SDI device to the output of AV-GM09M3-S1.
2. Connect the SDI input sources to the inputs of AV-GM09M3-S1.
3. Screw on the 5V power supply unit to the locking power jack.
4. Use IR remote, RS-232, or front panel push button to switch between input channels.
CONNECTION DIAGRAM

6
IR REMOTE CONTROL
F3
Power On / Off
Select Input to Output
Choose input source
1. Input source 1-10
→press input source (1-10) +
2. Input source 11-16
→press input source (1-6) + +
F1, F2, To
Reserved
WARRANTY
The SELLER warrants the AV-GM09M3-S1 16x4 3G/HD/SD-SDI Switch free from defects in the
material and workmanship for 3 years from the date of purchase from the SELLER or an authorized
dealer. Should this product fail to be in good working order within 3 years warranty period, The
SELLER, at its option, repair or replace the unit, provided that the unit has not been subjected to
accident, disaster, abuse or any unauthorized modifications including static discharge and power
surge. This warranty is offered by the SELLER for its BUYER with direct transaction only. This
warranty is void if the warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price of
parts and labor in effect at the time of repair. Such repairs are warranted for 90 days from the day
of reshipment to the BUYER. If the unit is delivered by mail, customers agree to insure the unit or
assume the risk of loss or damage in transit. Under no circumstances will a unit be accepted
without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without
limitations, any other implied warranty or fitness or merchantability for any particular purpose, all
of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are
responsible for shipping charges to and from the SELLER. Cables and power adapters are limited to
a 30 day warranty and must be free from any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However,
The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual.

7
The SELLER will NOT be liable for direct, indirect, incidental, special, or consequential damages
resulting from any defect or omission in this manual, even if advised of the possibility of such
damages. Also, the technical information contained herein regarding the AV-GM09M3-S1 features
and specifications is subject to change without further notice.
April, 2018
Support
For more info or tech support
http://www.siig.com/support