SIIG CE-000012-S1 User manual

1
Introducing the HDMI 4-Port Switch
The HDMI 4-Port Switch allows you to connect and switch
up to four high-definition digital audio/video source
devices through one High-Definition Multimedia
Interface (HDMI) on your high-definition television.
Features and Benefits
•Provides an all-digital audio/video connection
between devices such as HDTVs, DVD players/
recorders(Blu-ray®,HD-DVD,up-convertingDVD),
gaming systems, digital cable/satellite boxes and
AV receivers
•Provides four HDMI inputs and one HDMI output
•Supports digital video & audio HDMI standard
1.3b specification
•Signal amplification - extends interconnect copper
cable length up to 15 meters
•Supports 480i, 480p, 720i, 720p, 1080i and 1080p
resolution
•Easy switching between HDMI-enabled sources
using the IR remote control or Input Select button
PackageContents
•HDMI 4-Port Switch
•IR Remote Control and 2 AAA batteries
•Power Adapter
•Quick Installation Guide
HDMI 4-Port Switch
Quick Installation Guide
04-0455B

2
Layout
Figure 1. Front Panel Layout
Figure 2. Rear Panel Layout
Input Select
Button
HDMI In 1
Power Jack
HDMI Out
IR Receiver
Device LED
Power LED
HDMI In 2
HDMI In 3
HDMI In 4

3
Remote Control
Figure 3. Remote Control
On/Off
Direct Input
Select
Next/Previous
Input Select

4
Installation
1. Connect the HDMI cable (not included) from the
HDMI source device(s) into the HDMI inputs.
2. Connect the HDMI cable (not included) from your
HDTV, monitor, projector or another HDMI
receiving device into the HDMI Out port.
3. Plug the power adapter into the HDMI switch.
4. Plug the power adapter into a reliable power outlet.
5. Power on the HDMI switch.
Figure 3. Device Connection

5
Operation
Turn On/Off
Remote Control
•Press the On/Off button to power on or power off
the switch
Front Panel Input Select Button
•Press to power on the switch. To power off the
switch, press and hold the button for 4 seconds
Device Switching
Remote Control
•Press the desired Direct Input Select button to go
directly to the desired device
•Press the Next/Previous Input Select buttontocycle
through to the desired device
Front Panel Input Select Button
•With the switch powered on, press the button
repeatedly to cycle through to the desired device
Indicator LED
Power LED
The red Power LED will be lit when the switch is powered
on.
Device LED
Thereare four green Device LEDs on the front panel of the
switch. The LED of the selected device will be lit.

6
Blank Page

7
Technical Support and Warranty
QUESTIONS? SIIG’sOnline Support hasanswers! Simply visitour
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
toyour questionscould be just a few clicks away. You can alsosubmit
questions online and a technical support analysts will promptly
respond.
SIIGoffers a 5-yearmanufacturer warranty withthis product. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyour purchase has passed thestore's returnpolicy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
•Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
•Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
•You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
•SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.

HDMI 4-Port Switch is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of
SIIG,Inc. Othernamesusedinthispublicationareforidentificationonlyandmaybetrademarksoftheir
respectivecompanies.
April, 2008 Copyright ©2008 by SIIG, Inc. All rights reserved.
PRODUCT NAME
HDMI 4-Port Switch
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Ave.
Fremont, CA 94538-3152, USA
About SIIG, Inc.
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
of I/O connectivity products, including PCIe, PCI & ISA serial and
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire
(1394a/b),networking,sound cards,andother accessories. SIIGisthe
premier one-stop source of upgrades.
SIIGproductsoffer comprehensive usermanuals,many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.