SIIG JU-SC0211-S1 User manual

1
8-Port USB to RS-232
Serial Adapter Hub
Quick Installation Guide
04-0727B
Introduction
The 8-Port USB to RS-232 Serial Adapter Hub adds
eight 9-pin serial ports to your USB-equipped
system.
Key Features and Benefits
• Provides eight 9-pin (DB9) RS-232 ports
• Supports data transfer rate up to 230Kb/s
• Industrial metal housing
• USB Plug-n-play
System Requirements
• USB equipped computer with an available
USB port
• Windows®
8 (32-/64-bit) / 7 (32-/64-bit) /
Vista (32-/64-bit) / XP (32-/64-bit) / Server
2003 & 2008 (32-/64-bit) / Server 2008 R2
/ 2000

2
Package Contents
•8-Port USB to RS-232 Serial Adapter Hub
• USB 2.0 cable & power adapter
• Driver CD
• Quick installation guide
Layout
Figure 1: Layout
*Note: The Rx & Tx Activity LEDs will
blink when data is transfered through
the serial port.
Rx & Tx Activity LED*
Type B USB (to
computer)
Serial Port 3
Serial Port 1
Serial Port 4
Serial Port 2
Serial Port 6
Serial Port 8
Serial Port 5
Serial Port 7
Power Adapter Jack

3
Driver Installation
Make sure the driver is installed before plugging
the Serial Adapter into the computer. Do Not plug
the Serial Adapter into the computer until
instructed to do so.
Windows 8 (32-/64-bit) / 7 (32-/64-bit) /
Server 2008 R2
1. At the Windows desktop insert the driver
CD. Close the CD autoplay window if
prompted.
2. Click Windows key and R key,
For 32-bit: Type D:\32bit\MSSetup_
QUADPORT.exe,then press Enter.
For 64-bit & Server 2008 R2: type D:\64bit\
MSSetup_QUADPORT.exe, then press
Enter. (Change D: to match your CD-
ROM drive letter)
3. At User Account Control, click Yes. For
Server 2008 R2, skip this step.
4. At High-Speed USB MultiSerial Device
Drivers Setup box, click Install.

4
5. Wait until the High-Speed USB MultiSerial
Device Drivers Setup box prompt
Installation completed, then click Exit.
6. Plug the Serial Adapter into an available
USB port.
7. Drivers will install automatically. The Serial
Adapter is ready for use.
Windows Vista (32-/64-bit) / XP (32-/64-bit)
/ Server 2003 & 2008 (32-/64-bit) / 2000
1. At the Windows desktop insert the driver
CD. Close the CD autoplay window if
prompted.
2. Click Start, Run,
For 32-bit and 2000: Type D:\32bit\
MSSetup_QUADPORT.exe,then press
Enter.
For 64-bit: Type D:\64bit\MSSetup_
QUADPORT.exe, then press Enter.
(Change D: to match your CD-ROM drive
letter)
3. At User Account Control, click Allow or
Continue. Skip this step if not prompted.

5
4. At High-Speed USB MultiSerial Device
Drivers Setup box, click Install.
5. For 2000, click Yes at the Digital Signature
Not Found. For other OSes, skip this step.
6. Wait until the High-Speed USB MultiSerial
Device Drivers Setup box prompt
Installation completed, click Exit.
7. Plug the Serial Adapter into an available
USB port.
8. For 2000, click Yes at the Digital Signature
Not Found 1-2 times. For other OSes, skip
this step.
9. Drivers will install automatically. The Serial
Adapter is ready for use.
To Verify Installation
1. Check Device Manager to verify
installation.
For Windows 8 / 7 / XP / Server 2003 / 2000:
Right click Computer or My Computer,
click Manage, then click Device Manager.
For Windows Vista:Right click Computer,
click Manage, click Continue, then click
Device Manager.

6
For Server 2008 / 2008 R2: Right click
Computer, click Manage, double click
Diagnostics, then click Device Manager.
2. Double click Ports (COM & LPT),
eight High-Speed USB Serial Port... should
be displayed.
Changing COM Port Number
Some serial devices need a specific COM port in
ordertowork. Ifyourserialdeviceworksproperly,
do not change this setting.
1. From Device Manager double click Ports
(COM & LPT), then double click the High-
Speed USB Serial Port port you want to
change.
2. Click Features tab.
3. Click the down arrow that is next to the
COM Port Number drop down box and
select a COM port that is not in use.
4. Click OK to save the changes.
5. Unplug the Serial Adapter from the USB
port, then re-plug the Serial Adapter into the
same USB port to enable the changes.

7
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at
www.siig.com and click Support. Our online support database is updated daily with
new drivers and solutions. Answers to your questions could be just a few clicks away.
You can also submit questions online and a technical support analyst will promptly
respond.
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the
original purchaser and guarantees the product to be free of any defects in materials or
workmanship for five (5) years from the date of purchase of the product.
SIIG will, at our discretion, repair or replace (with an identical product or product
having similar features and functionality) the product if defective in materials or
workmanship. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Please see our web site for more warranty details.
If you encounter any problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the product to the store
where you purchased from.
B) If your purchase has passed the store's return policy period, please follow the steps
below to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then REQUEST A PRODUCT REPLACEMENT
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request
will be processed, if the product is determined to be defective, an RMA number will
be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All accessories that came with the
original package must be included.
• Clearly write your RMA number on the top of the returned package. SIIG will
refuse to accept any shipping package, and will not be responsible for a product
returned without an RMA number posted on the outside of the shipping
carton.
• You are responsible for the cost of shipping to SIIG. Ship the product to the
following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground in the U.S. and
International Economy outside of the U.S. at no cost to the customer.

PRODUCTNAME
8-Port USB to RS-232 Serial Adapter Hub
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG,Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: [phone]
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,
and legacy I/O adapters) that bridge the connection between Desktop/
Notebooksystemsand external peripherals. SIIG continuestogrow by adding
A/V and Digital Signage connectivity solutions to our extensive portfolio.
SIIGproducts offer comprehensive usermanuals, many user-friendly features,
and are backed by an extensive manufacturer warranty. High quality control
standards are evident by the overall ease of installation and compatibility of
our products, as well as one of the lowest defective return rates in the industry.
SIIG products can be found in computer retail stores, mail order catalogs,
throughmajordistributors, system integrators, and VARsinthe Americas and
the UK, and through e-commerce sites.
8-Port USB to RS-232 Serial Adapter Hub is a trademark of SIIG, Inc. SIIG and the SIIG logo
are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of
Microsoft Corporation. All other names used in this publication are for identification only
and may be trademarks of their respective owners.
June, 2013 Copyright © 2013 by SIIG, Inc. All rights reserved.