Silicon Laboratories C8051F340 User manual

Rev. 0.3 2/14 Copyright © 2014 by Silicon Laboratories C8051F34x
C8051F34x
C8051F34XDEVELOPMENT KIT USER’SGUIDE
1. Kit Contents
The C8051F34x Development Kit contains the following items:
• C8051F340 Target Board
• C8051Fxxx Development Kit Quick-Start Guide
• AC to DC Power Adapter
• USB Debug Adapter (USB to Debug Interface)
• USB Cable
• CD-ROM
2. Hardware Setup Using a USB Debug Adapter
The target board is connected to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown
in Figure 1.
1. Connect the USB Debug Adapter to the DEBUG connector on the target board with the 10-pin ribbon cable.
2. Connect one end of the USB cable to the USB connector on the USB Debug Adapter.
3. Connect the other end of the USB cable to a USB Port on the PC.
4. Connect the ac/dc power adapter to power jack P1 on the target board.
Notes:
• Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter.
• Remove power from the target board before removing the ribbon cable from the target board. Connecting or
disconnecting the cable when the devices have power can damage the device and/or the USB Debug
Adapter.
Figure 1. Hardware Setup Using a USB Debug Adapter
Notes:The C8051F340 target board has the ability to be powered through the USB cable. To enable the USB-powered mode,
short the pins labeled VBUS and VREGIN on the J8 header. Do not short all 3 pins on the J8 header.
PC
USB
Cable
USB Debug Adapter
AC/DC
Adapter
Target Board
SILICON LABORATORIES
PWR
P1.6
P3.7RESET
Port 4Port 3Port 1
Port 2 Port 0
MCU
Silicon Laboratories
USB DEBUG ADAPTER
Run
StopPower
Not Recommended for New Designs

C8051F34x
2 Rev. 0.3
3. Software Setup
Simplicity Studio greatly reduces development time and complexity with Silicon Labs EFM32 and 8051 MCU
products by providing a high-powered IDE, tools for hardware configuration, and links to helpful resources, all in
one place.
Once Simplicity Studio is installed, the application itself can be used to install additional software and
documentation components to aid in the development and evaluation process.
Figure 2. Simplicity Studio
The following Simplicity Studio components are required for the C8051F340 Development Kit:
8051 Products Part Support
Simplicity Developer Platform
Download and install Simplicity Studio from www.silabs.com/8bit-software or www.silabs.com/simplicity-studio.
Once installed, run Simplicity Studio by selecting StartSilicon LabsSimplicity StudioSimplicity Studio
from the start menu or clicking the Simplicity Studio shortcut on the desktop. Follow the instructions to install the
software and click Simplicity IDE to launch the IDE.
The first time the project creation wizard runs, the Setup Environment wizard will guide the user through the
process of configuring the build tools and SDK selection.
In the Part Selection step of the wizard, select from the list of installed parts only the parts to use during
development. Choosing parts and families in this step affects the displayed or filtered parts in the later device
selection menus. Choose the C8051F34x family by checking the C8051F34x check box. Modify the part selection
at any time by accessing the Part Management dialog from the WindowPreferencesSimplicity
StudioPart Management menu item.
Simplicity Studio can detect if certain toolchains are not activated. If the Licensing Helper is displayed after
completing the Setup Environment wizard, follow the instructions to activate the toolchain.
Not Recommended for New Designs

C8051F34x
Rev. 0.3 3
3.1. Running Blinky
Each project has its own source files, target configuration, SDK configuration, and build configurations such as the
Debug and Release build configurations. The IDE can be used to manage multiple projects in a collection called a
workspace. Workspace settings are applied globally to all projects within the workspace. This can include settings
such as key bindings, window preferences, and code style and formatting options. Project actions, such as build
and debug are context sensitive. For example, the user must select a project in the Project Explorer view in order
to build that project.
To create a project based on the Blinky example:
1. Click the Simplicity IDE tile from the Simplicity Studio home screen.
2. Click the Create new project link from the welcome screen or go to FileNewSilicon Labs MCU
Project.
3. In the Kit drop-down, select C8051F340 Development Kit, in the Part drop-down, select C8051F340, and
in the SDK drop-down, select the desired SDK. Click Next.
4. Select Example and click Next.
5. Under C8051F340 Development Kit in the Blinky folder, select F34x Blinky and click Finish.
6. Click on the project in the Project Explorer and click Build, the hammer icon in the top bar. Alternatively,
go to ProjectBuild Project.
7. Click Debug to download the project to the hardware and start a debug session.
8. Press the Resume button to start the code running. The LED should blink.
9. Press the Suspend button to stop the code.
10. Press the Reset the device button to reset the target MCU.
11. Press the Disconnect button to return to the development perspective.
3.2. Simplicity Studio Help
Simplicity Studio includes detailed help information and device documentation within the tool. The help contains
descriptions for each dialog window. To view the documentation for a dialog, click the question mark icon in the
window:
This will open a pane specific to the dialog with additional details.
The documentation within the tool can also be viewed by going to HelpHelp Contents or HelpSearch.
Not Recommended for New Designs

C8051F34x
4 Rev. 0.3
3.3. Legacy 8-bit IDE
Note: Using the Simplicity Studio tools with the C8051F340 Development Kit is recommended. See section 3. "Software
Setup‚" on page 2 for more information.
Download the 8-bit software from the website (www.silabs.com/8bit-software) or use the provided installer on the
CD-ROM to install the software tools for the C8051F34x devices. After installation, examples can be found in
...\Examples\C8051F34x in the installation directory. At a minimum, the C8051F340 DK requires:
Silicon Labs IDE—Software enabling initial evaluation, development, and debugging.
Configuration Wizard 2—Initialization code generation software for the C8051F34x devices.
Keil C51 Tools—Keil 8051 Compiler/Assembler/Linker toolchain.
Other software available includes:
Keil µVision Driver—Driver for the Keil µVision IDE that enables development and debugging on
C8051Fxxx MCUs.
Flash Programming Utilities and MCU Production Programmer—Programming utilities for the
production line. More information on the available programming options can be found on the website:
http://www.silabs.com/products/mcu/Pages/ProgrammingOptions.aspx.
ToolStick Development Tools—Software and examples for the ToolStick development platform. More
information on this platform can be found at www.silabs.com/toolstick.
The development kit includes the latest version of the C51 Keil 8051 toolset. This toolset is initially limited to a code
size of 2 kB and programs start at code address 0x0800. After registration, the code size limit is removed entirely
and programs will start at code address 0x0000.
To register the Keil toolset:
1. Find the Product Serial Number printed on the CD-ROM. If you no longer have this serial number,
register on the Silicon Labs website (www.silabs.com/8bit-software) to obtain the serial number.
2. Open the Keil µVision4 IDE from the installation directory with administrative privileges.
3. Select FileLicense Management to open the License Management window.
Figure 3. Keil µVision4 IDE License Management Window
4. Click on the Get LIC via Internet... button to open the Obtaining a License IDE Code (LIC) window.
5. Press OK to open a browser window to the Keil website. If the window doesn’t open, navigate to
www.keil.com/license/install.htm.
6. Enter the Silicon Labs Product Serial Number printed on the CD-ROM, along with any additional required
Not Recommended for New Designs

C8051F34x
Rev. 0.3 5
information.
7. Once the form is complete, click the Submit button. An email will be sent to the provided email address
with the license activation code.
8. Copy the License ID Code (LIC) from the email.
9. Paste the LIC into the New License ID Code (LIC) text box at the bottom of the License Management
window in µVision4.
10. Press the Add LIC button. The window should now list the PK51 Prof. Developers Kit for Silabs as a
licensed product.
11. Click the Close button.
Not Recommended for New Designs

C8051F34x
6 Rev. 0.3
4. Target Board
The C8051F34x Development Kit includes a target board with a C8051F340 device pre-installed for evaluation and
preliminary software development. Numerous input/output (I/O) connections are provided to facilitate prototyping
using the target board. Refer to Figure 4 for the locations of the various I/O connectors.
P1 Power connector (accepts input from 7 to 15 VDC unregulated power adapter)
P2 Analog I/O terminal block
P3 USB connector
P4 RS232 connector
J1 Supply signal header
J2 Port 0 header
J3 Port 1 header
J4 Port 2 header
J5 Port 3 header
J6 Port 4 header
J7 Connects the +3V supply net to the VDD supply net
J8 USB Power or VDD power selection header
J9 Debug connector for debug adapter interface
J10, J11 External crystal enable connectors
J12 Port I/O jumper configuration block
J13 96-pin female connector
J15 Jumper connection for pin 1.5 to capacitors (used when VREF is internally generated)
J16 Jumper connection for potentiometer source to VDD
J17 Jumper connection for potentiometer to pin 2.5
J19 Serial Adapter target board power connector
Figure 4. C8051F340 Target Board
C8051F340-TB
DEBUG
J9
P1
RESET
P2.0
P2.1
J6
J5
J4
J3
J1
J15
J11
J12
J8
J2
J19
340
J16
J17
USB
P3
P4
RS232
PWR
SILICON LABORATORIES
J10
J7
D4
D3
D2
U1
J13
P2
SW3 SW2 SW1
R10
Not Recommended for New Designs

C8051F34x
Rev. 0.3 7
4.1. System Clock Sources
The C8051F340 device installed on the target board features a calibrated programmable internal oscillator which is
enabled as the system clock source on reset. After reset, the internal oscillator operates at a frequency of 1.5 MHz
(±1.5%) by default but may be configured by software to operate at other frequencies. Therefore, in many
applications an external oscillator is not required. However, if you wish to operate the C8051F340 device at a
frequency not available with the internal oscillator, an external crystal may be used. Refer to the C8051F34x
datasheet for more information on configuring the system clock source.
The target board is designed to facilitate the installation of an external crystal. Remove shorting blocks at headers
J10 and J11 and install the crystal at the pads marked Y1. Install a 10 Mresistor at R1 and install capacitors at C6
and C7 using values appropriate for the crystal you select. Refer to the C8051F34x datasheet for more information
on the use of external oscillators.
4.2. Switches and LEDs
Three switches are provided on the target board. Switch RESET is connected to the RESET pin of the C8051F340.
Pressing RESET puts the device into its hardware-reset state. Switches P2.0 and P2.1 are connected to the
C8051F340’s general purpose I/O (GPIO) pins through headers. Pressing P2.0 or P2.1 generates a logic low
signal on the port pin. Remove the shorting blocks from the J12 header to disconnect Switch P2.0 and Switch P2.1
from the port pins. The port pin signals are also routed to pins on the J1 I/O connector. See Table 1 for the port pins
and headers corresponding to each switch.
Three LEDs are also provided on the target board. The red LED labeled PWR LED is used to indicate a power
connection to the target board. The green surface-mount LEDs labeled with port pin names are connected to the
C8051F340’s GPIO pins through headers. Remove the shorting blocks from the header to disconnect the LEDs
from the port pin. The port pin signals are also routed to pins on the J1 I/O connector. See Table 1 for the port pins
and headers corresponding to each LED.
Also included on the C8051F340 target board is a 10 KThumb-Wheel Rotary Potentiometer, part number R10.
The Potentiometer is connected to the C8051F340’s P2.5 pin through the J17 header. Remove the shorting block
from the header to disconnect the Potentiometer from the port pin. The port pin signal is also routed to a pin on the
J1 I/O connector. See Table 1 for the port pin and header corresponding to the Potentiometer.
Table 1. Target Board I/O Descriptions
Description I/O Header
SW1 Reset none
SW2 P2.0 J12[1–2]
SW3 P2.1 J12[3–4]
Green LED P2.2 J12[5–6]
Green LED P2.3 J12[7–8]
Red LED PWR none
Potentiometer P2.5 J17
Not Recommended for New Designs

C8051F34x
8 Rev. 0.3
4.3. Universal Serial Bus (USB) Interface (J14)
A Universal Serial Bus (USB) connector (P3) is provided to facilitate connections to the USB interface on the
C8051F340. Table 2 shows the J14 pin definitions.
4.4. PORT I/O Connectors (J2 - J6)
In addition to all port I/O signals being routed to the 96-pin expansion connector, each of the five parallel ports of
the C8051F340 has its own 10-pin header connector. Each connector provides a pin for the corresponding port
pins 0–7, +3.3 VDC and digital ground. Table 3 defines the pins for the port connectors. The same pin-out order is
used for all of the port connectors.
4.5. USB Self-Powered Configuration (J8)
The C8051F340 target board can be configured as a self-powered USB device to take power from the USB cable
instead of the ac/dc adapter connected at P1. To configure the target boards as a self-powered USB device, short
the VREGIN and VBUS pins on the J8 header
Note: When the C8051F340 target board is self-powered from the USB, the Serial Adapter is not powered from the
target board. The Serial Adapter must be powered directly by connecting the ac/dc adapter to the Serial Adapters’
dc power jack. Also, the RS232 Serial Interface (P4) cannot be used when powering the target board from the
USB.
Table 2. USB Connector Pin Descriptions
Pin # Description
1 VBUS
2D-
3D+
4 GND (Ground)
Table 3. J12–J19 Port Connector Pin Descriptions
Pin # Description
1Pn.0
2Pn.1
3Pn.2
4Pn.3
5Pn.4
6Pn.5
7Pn.6
8Pn.7
9 +3VD(+3.3VDC)
10 GND (Ground)
Not Recommended for New Designs

C8051F34x
Rev. 0.3 9
4.6. Target Board DEBUG Interface (J9)
The DEBUG connector (J9) provides access to the DEBUG (C2) pins of the C8051F340. It is used to connect the
Serial Adapter or the USB Debug Adapter to the target board for in-circuit debugging and Flash programming.
Table 4 shows the
DEBUG pin definitions.
4.7. Serial Interface (P4)
A RS232 transceiver circuit and DB-9 (P4) connector are provided on the target board to facilitate serial
connections to UART0 of the C8051F340. The TX, RX, RTS and CTS signals of UART0 may be connected to the
DB-9 connector and transceiver by installing shorting blocks on header J12.
J12[9-10]- Install shorting block to connect UART0 TX (P0.4) to transceiver.
J12[11-12]- Install shorting block to connect UART0 RX (P0.5) to transceiver.
J12[13-14]- Install shorting block to connect UART0 RTS (P2.6) to transceiver.
J12[15-16]- Install shorting block to connect UART0 CTS (P2.7) to transceiver.
4.8. Analog I/O (P2)
Several of the C8051F340 target device’s port pins are connected to the P2 terminal block. Refer to Table 5 for the
P2 terminal block connections.
4.9. USB Debug Adapter Target Board Power Connector (J19)
The USB Debug Adapter includes a connection to provide power to the target board. This connection is routed
from J9[10] to J19[SER_PWR]. Place a shorting block at header J19[REG_IN-P1_PWR] to power the board
directly from an ac/dc power adapter. Place a shorting block at header J19[REG_IN-SER_PWR] to power the
board from the USB Debug Adapter. Please note that the second option is not supported with either the EC1 or
EC2 Serial Adapters.
Table 4. DEBUG Connector Pin Descriptions
Pin # Description
1 +3VD(+3.3VDC)
2, 3, 9 GND (Ground)
4C2D
5/RST(Reset)
6P3.0
7C2CK
8 Not Connected
10 USB Power
Table 5. J6 Terminal Block Pin Descriptions
Pin # Description
1 P1.1 / AIN1.1
2 P1.2 / AIN1.2
3 GND (Ground)
4 P1.5 / VREF (Voltage Reference)
Not Recommended for New Designs

C8051F34x
10 Rev. 0.3
5. Schematics
Figure 5. C8051F340 Target Board Schematic (Page 1 of 2)
Not Recommended for New Designs