Simons Voss 3061 FD User manual

Digital Locking Cylinder
3061
Manual
16.12.2019

Contents
1 Intended use ................................................................................................................................................ 5
2 General safety instructions.....................................................................................................................6
3 Product specific safety notices ........................................................................................................... 10
4 General ........................................................................................................................................................ 14
4.1 Product description....................................................................................................................................... 14
4.2 Locking cylinder design ............................................................................................................................... 15
4.3 Half cylinder design....................................................................................................................................... 15
4.4 Opening and locking from the outside ................................................................................................ 16
4.5 Opening and locking from the inner side............................................................................................ 16
5 Versions .......................................................................................................................................................17
5.1 FD version (Standard)................................................................................................................................. 18
5.2 HZ version (Standard) ................................................................................................................................ 18
5.3 Half-cylinder (HZ) version (self-locking)........................................................................................... 18
5.4 ZK version .......................................................................................................................................................... 18
5.5 version for steel and fire retardant doors........................................................................................... 19
5.6 TS version .......................................................................................................................................................... 19
5.7 MR option........................................................................................................................................................... 19
5.8 MS version ......................................................................................................................................................... 19
5.9 SKG or VdS versions (SZ).......................................................................................................................... 19
5.10 AP version ......................................................................................................................................................... 20
5.11 AP2 Version........................................................................................................................................................21
5.12 CO version..........................................................................................................................................................22
5.13 WP Version (FD) ............................................................................................................................................22
5.14 WP version (HZ/CO/AP) ...........................................................................................................................22
5.15 SW version (CO) ............................................................................................................................................22
5.16 VR version (HZ) ..............................................................................................................................................22
5.17 DK version (HZ) ..............................................................................................................................................22
5.18 WN version (HZ) ............................................................................................................................................23
5.19 DM version .........................................................................................................................................................23
5.20 Hybrid-Version.................................................................................................................................................23
5.21 Extra lengths.....................................................................................................................................................23
5.22 Examples of locking cylinder use ...........................................................................................................23
6 Installation instructions .........................................................................................................................25
Digital Locking Cylinder 3061 (Manual) Contents
2 / 54

6.1 General instructions......................................................................................................................................25
6.2 Programming the locking cylinder .........................................................................................................25
6.3 Installation variants ......................................................................................................................................25
6.3.1 Installation of double thumb-turn cylinders (except types .AP/.SKG/.VdS) ......
25
6.3.2 Fitting an anti-panic cylinder .................................................................................................. 27
6.3.3 Installation of SKG/VdS cylinders ...................................................................................... 30
6.3.4 Half Cylinder DK/MR....................................................................................................................31
6.3.5 Installing Swiss Round...............................................................................................................33
7 Audible signals......................................................................................................................................... 34
7.1 Battery warnings ........................................................................................................................................... 34
7.2 Battery warning for transponders..........................................................................................................37
8 System 3060 battery replacement .................................................................................................. 38
8.1 General instructions..................................................................................................................................... 38
8.2 Battery life ........................................................................................................................................................ 38
8.3 Emergency battery procedure................................................................................................................ 39
8.3.1 Storage mode (G1)..................................................................................................................... 39
8.3.2 Freeze mode (G2)....................................................................................................................... 39
8.4 Procedure .........................................................................................................................................................40
8.5 Procedure for outer thumb turn (MH cylinder) ............................................................................... 41
9 Maintenance, cleaning and disinfection.......................................................................................... 43
10 Areas of use .............................................................................................................................................. 44
10.1 General...............................................................................................................................................................44
10.2 Fire doors........................................................................................................................................................... 44
10.3 Doors along rescue routes........................................................................................................................ 44
10.4 Installation outdoors ...................................................................................................................................44
11 Accessories ............................................................................................................................................... 45
11.1 Thumb-turns................................................................................................................................................... 45
11.2 Core extraction protection adapter (Z4.KA.SET)......................................................................... 45
11.3 Core extraction protection extension for SKG/VdS cylinders (Z4.KA.SET2) ................. 45
11.4 Core extraction protection extension for SKG/VdS cylinders (Z4.KA.SET2.IT) ............ 45
11.5 Tool......................................................................................................................................................................46
11.6 Battery set ........................................................................................................................................................46
12 Technical data ..........................................................................................................................................47
12.1 Locking cylinder ..............................................................................................................................................47
12.2 Half cylinder.....................................................................................................................................................49
Digital Locking Cylinder 3061 (Manual) Contents
3 / 54

13 Declaration of conformity ......................................................................................................................51
14 Help and other information ..................................................................................................................52
Digital Locking Cylinder 3061 (Manual) Contents
4 / 54

1 Intended use
Digital SimonsVoss Locking Cylinder 3061 are installed in designated door
locks, such as DIN mortise locks, to integrate them into a digital locking
system.
The digital Locking Cylinder 3061 may only be used for its intended purpose
in a designated door locking device. No other use is permitted.
Digital Locking Cylinder 3061s are available in various lengths. The selection
of the proper size is of significance. The length of the locking cylinder is
printed on the packaging and can be measured at any time. If the cylinder is
too short, the handles cannot be fitted. If the cylinder is too long, it may be
ripped out of the locking device. The may not protrude more than 3 mm on
each side of the door to ensure proper operation.
The product may not be changed in any way, other than in compliance with
the changes described in the instructions.
Digital Locking Cylinder 3061
(Manual)
1. Intended use
5 / 54

2 General safety instructions
Signal word (ANSI Z535.6) Possible immediate effects of non-
compliance
DANGER Death or serious injury (likely)
WARNING Death or serious injury (possible, but
unlikely)
CAUTION Minor injury
IMPORTANT Property damage or malfunction
NOTE Low or none
WARNING
Blocked access
Access through a door may stay blocked due to incorrectly fitted and/or in-
correctly programmed components. SimonsVoss Technologies GmbH is
not liable for the consequences of blocked access such as access to in-
jured or endangered persons, material damage or other damage!
WARNING
Blocked access through manipulation of the product
If you change the product on your own, malfunctions can occur and access
through a door can be blocked.
Modify the product only when needed and only in the manner described
in the documentation.
CAUTION
Fire hazard posed by batteries
The batteries used may pose a fire or burn hazard if handled incorrectly.
1. Do not try to charge, open, heat or burn the batteries.
2. Do not short-circuit the batteries.
Digital Locking Cylinder 3061
(Manual)
2. General safety instructions
6 / 54

IMPORTANT
Damage resulting from electrostatic discharge (ESD)
This product contains electronic components that may be damaged by
electrostatic discharges.
1. Use ESD-compliant working materials (e.g. Grounding strap).
2. Ground yourself before carrying out any work that could bring you into
contact with the electronics. For this purpose, touch earthed metallic
surfaces (e.g. door frames, water pipes or heating valves).
IMPORTANT
Damage resulting from liquids
This product contains electronic components that may be damaged by li-
quids of any kind.
Keep liquids away from the electronics.
IMPORTANT
Damage resulting from aggressive cleaning agents
The surface of this product may be damaged as a result of the use of un-
suitable cleaning agents.
Only use cleaning agents that are suitable for plastic or metal surfaces.
IMPORTANT
Damage as a result of mechanical impact
This product contains electronic components that may be damaged by
mechanical impacts of any kind.
1. Avoid touching the electronics.
2. Avoid other mechanical influences on the electronics.
IMPORTANT
Damage due to polarity reversal
This product contains electronic components that may be damaged by re-
verse polarity of the power source.
Do not reverse the polarity of the voltage source (batteries or mains
adapters).
Digital Locking Cylinder 3061
(Manual)
2. General safety instructions
7 / 54

IMPORTANT
Failure of operation due to different discharged batteries
This product uses one or more batteries for power supply. The batteries are
discharged at approximately the same rate.
Always replace all batteries at the same time.
IMPORTANT
Operational malfunction due to radio interference
This product may be affected by electromagnetic or magnetic interference.
Do not mount or place the product directly next to devices that could
cause electromagnetic or magnetic interference (switching power
supplies!).
IMPORTANT
Communication interference due to metallic surfaces
This product communicates wirelessly. Metallic surfaces can greatly re-
duce the range of the product.
Do not mount or place the product on or near metallic surfaces.
NOTE
Intended use
SimonsVoss-products are designed exclusively for opening and closing
doors and similar objects.
Do not use SimonsVoss products for any other purposes.
NOTE
Battery contact malfunction due to grease film
When touching batteries, leave a thin film of skin grease on the batteries.
This film deteriorates the contact between the electronics and the batter-
ies.
1. Do not touch the contacts of the new batteries with your hands.
2. Use clean and grease-free gloves.
Digital Locking Cylinder 3061
(Manual)
2. General safety instructions
8 / 54

NOTE
Dispose of the batteries as per local and country-specific regulations.
NOTE
Function error due to poor battery contact
If the contact surface to the battery is too small, then the battery connec-
tion may not create a stable connection to the battery.
Only use batteries that are approved by SimonsVoss.
NOTE
Qualifications required
The installation and commissioning requires specialized knowledge.
Only trained personnel may install and commission the product.
NOTE
Modifications or further technical developments cannot be excluded and
may be implemented without notice.
NOTE
The German language version is the original instruction manual. Other lan-
guages (drafting in the contract language) are translations of the original
instructions.
NOTE
Read and follow all installation, installation, and commissioning instruc-
tions. Pass these instructions and any maintenance instructions to the user.
Digital Locking Cylinder 3061
(Manual)
2. General safety instructions
9 / 54

3 Product specific safety notices
WARNING
Fault in escape door function due to unsuitable closing cylinder or un-
suitable environment
The use of unsuitable closing cylinders or components that are not opera-
tional can adversely affect the function of an escape door. If you use the
anti-panic cylinder in locks that are not approved, the escape door function
can be disrupted and not released again. Contact SimonsVoss Technolo-
gies GmbHfor further information.
1. Ensure that all parts of the lock are operational.
2. Check that the panic function of the mortice lock is ensured.
3. Only use the anti-panic cylinder in locks that are expressly approved for
the anti-panic cylinder. See also the manufacturer's documentation in
this respect.
4. Do not use the anti-panic cylinder in temperatures below -20 °C or
above +50 °C.
5. Carry out a function test of the anti-panic cylinder after installation or
after a battery change.
CAUTION
Use of the anti-panic version of the locking cylinder in non-approved
locks
If you use the anti-panic version of the locking cylinder in unauthorised
locks, the escape door function may be impaired and cannot be released
again.
1. Only use the anti-panic version of the locking cylinder in locks for which
the locking cylinder is expressly approved.
2. Please refer to the documentation of the respective lock manufacturer.
3. Contact SimonsVoss Technologies GmbH for further information on this
subject (see
Help and other information [}52] ).
Digital Locking Cylinder 3061
(Manual)
3. Product specific safety notices
10 / 54

CAUTION
Hand injuries from carrier springing back
A spring-loaded carrier is used in the anti-panic construction of the closing
cylinder. This carrier can spring back when it is not installed, causing hand
injuries.
Do not hold the anti-panic construction of the closing cylinders in the
area of the carrier.
IMPORTANT
Damage caused by moisture in outdoor use
Moisture can damage the electronics.
1. If you want to use the locking cylinder for outdoor applications or in high
humidity (bathrooms or washrooms), use the WP version.
2. Carefully insert the locking cylinder to avoid damaging the O-rings.
IMPORTANT
Mechanical damage to the thumb-turn as a result of obstacles
If the thumb-turn can knock against the wall or other objects as a result of
the installation situation, it may become damaged.
In such situations, use a suitable door stop.
IMPORTANT
Mechanical damage to the knob through misuse as door-opener
Some doors are very heavy and solidly constructed. The knob is not suit-
able for opening such doors.
1. Don't pull the knob to open doors.
2. Make suitable door openers available (suitable handles) to avoid
misuse of the knob.
Digital Locking Cylinder 3061
(Manual)
3. Product specific safety notices
11 / 54

NOTE
Service interval of not less than one month for emergency exit locks
The European standard EN 179 (attachment C) specifies that emergency
exit locks must be serviced monthly. The anti-panic function must be in a
satisfactory and operational condition.
Ensure during a monthly service that fault-free and operational
condition of the anti-panic construction of the closing cylinder is
guaranteed.
NOTE
Qualifications required
The installation and commissioning requires specialized knowledge.
Only trained personnel may install and commission the product.
NOTE
Inclusion of persons without means of identification
The freely-rotating construction of the closing cylinder can only be opened
with a means of identification from both sides.
Ensure that no persons without means of identification are in the
secured area.
NOTE
Length of locking system password
For security reasons, the locking system password must consist of at least
8 characters. The code length for digital closing cylinders
(and for System
3060/3061 and MobileKey) corresponds to 2168 Bit.
NOTE
Fault in the interior knob due to moisture
The inner knob of the closing cylinder is of protection class IP40 and is thus
not protected from moisture.
Ensure that the interior knob cannot come into contact with water.
Digital Locking Cylinder 3061
(Manual)
3. Product specific safety notices
12 / 54

NOTE
Battery changes may only be carried out by trained personnel and only with
the battery key provided (Z4.KEY)!
NOTE
Programming with obsolete LSM version
New components can only be programmed with the current version of
LSM.
NOTE
Difficulty of operation of the lock due to stiff latch or bolt
If the latch or bolt of the mortice lock are stiff, the closing cylinder will also
be stiff.
Check that the latch or the bolt of the mortice lock are free-moving.
NOTE
Fitting error or incorrect order
If you make a mistake in measuring the door and order a closing cylinder,
the closing cylinder will not fit.
Check the dimensions of the door again before ordering.
Digital Locking Cylinder 3061
(Manual)
3. Product specific safety notices
13 / 54

4 General
4.1 Product description
The SimonsVoss Digital Locking System 3060 is an electronic version of a
mechanical locking system with the functions of a typical access control
system.
Digital Locking Cylinder 3061 and the digital half cylinder are a main
component in the locking and access control system, where radio
communication replaces the mechanical authentication of a conventional
key.
This product description details both the locking cylinder and the half
cylinder. The design and operating mode of the two products are
comparable in many respects. Any differences between the two products
and different versions are pointed out in the corresponding sections.
'Locking cylinder' is taken to mean both 'locking cylinder' and 'half cylinder'
in this document unless explicitly stated otherwise or taken out of context.
Data are transmitted for authentication using a transponder (25kHz
inductive) or a smart card featuring the RFID standard MIFARE© Classic or
MIFARE© DESFire.
Refer to the respective manuals for details about smart card products
(SC). This description mentions the smart card cylinder, but does not
describe it in any detail.
The locking cylinder is supplied in different versions and meets different
profile standards, such as DIN 18252/EN1303, so that almost any lock
anywhere in the world can be retrofitted with this cylinder. Digital Locking
Cylinder 3061 has much to offer – greater security, greater flexibility, lower
costs, network-ready without any wiring on the door or frame and less time
and effort required for installation.
Digital Locking Cylinder 3061 is powered by two batteries in a redundant
system. Cylinders operate as stand-alone components thanks to this
integrated power supply, which also means there is no need to wire doors.
An intelligent battery warning system also increases reliability.
The SimonsVoss system elements are not configured before delivery from
the factory. They are first assigned to a locking system during initial
programming. This makes it easier for stock keeping and makes product
management simpler.
Thanks to modularity, all locking cylinders are seamlessly integrated into
the SimonsVoss System 3060 and, like all SimonsVoss components, they
can be programmed using the locking plan software. Other authentication
components, such as Pin Code Keypad 3068, Biometric Reader Q3008 or
Digital Locking Cylinder 3061
(Manual)
4. General
14 / 54

Compact Reader 3078, can be connected as a wireless element. If the
system is extended at a later stage, cylinders can be networked without
wiring and managed in an online interconnected system.
The locking cylinders are provided with two different firmware generations
– G1 and G2. G2 features a more efficient communication protocol than G1.
It will allow you to create larger, more efficient locking systems.
Authorisations are written both on the locking cylinder and the transponder,
thus delivering greater flexibility for programming. A G2 system can also
form a virtual network, i.e. authorisations and blocking lists are written on
the transponder and transmitted into the locking system. Refer to the G2
manual for more details.
4.2 Locking cylinder design
1. Inside thumb-turn
2. Batteries/electronics
3. Actuator
4. Drilling protection
5. Outer thumb-turn
4.3 Half cylinder design
1. Actuator
2. Electronics
3. Batteries
4. Thumb-turn
Digital Locking Cylinder 3061
(Manual)
4. General
15 / 54

4.4 Opening and locking from the outside
With freely rotating locking cylinders (FD)
The outer and inside thumb-turn rotate freely when not activated in the
freely rotating Locking Cylinder 3061, meaning it is not possible to open or
lock the door without a valid ID medium. Identify yourself with your valid ID
medium on the outer thumb-turn to activate the cylinder. If the ID medium
is authorised, an audible signal will sound twice, the blue LED will flash
twice and the locking cylinder will engage ready to open. Turn the outer
thumb-turn in the direction of locking or opening. You have about five
seconds to do so. The engage time can be configured. A single audible
signal will then sound and the outer or inside thumb-turn will rotate freely
again. Ensure that the outside or inside locking cylinder thumb-turn rotates
freely again after the thumb-turn has been engaged ready for use.
NOTE
If the user has an ID medium which is not authorised for use at that particu-
lar moment due to the time zone plan, a single audible signal will sound.
The cylinder will not engage, so the outer or inside thumb-turn continues to
rotate freely and the user cannot open the door. You need to configure this
response separately in third-party systems.
4.5 Opening and locking from the inner side
With freely rotating locking cylinders (FD)
The outer and inside thumb-turn rotate freely when not activated in the
freely rotating Locking Cylinder 3061, Doors can also only be opened or
locked on the outside using an ID medium on the inside thumb-turn.
With non-freely rotating locking cylinders (CO)
Locking Cylinder 3061s which are permanently engaged for use can be
operated from the inside without a ID medium. In this case, the door can be
opened and closed using the inside thumb-turn without an authorised ID
medium.
Digital Locking Cylinder 3061
(Manual)
4. General
16 / 54

5 Versions
Different versions of the digital Locking Cylinder 3061 are offered to cover
the different needs of the market. The different versions are indicated by a
code. The different versions can be combined:
ABBREVIATION DESIGNATION LOCKING CYLIN-
DER HALF CYLINDER
FD Standard (freely
rotating) X
HZ Half cylinder X
Access control Access Control X X
FH Fire-retardant
version X
TS Button control X
MR Multi-point X X
MS Brass version X X
SKG
Class AZ VdS cyl-
inder (basic pro-
tection against
picking)
X
VDS
Class BZ VdS cyl-
inder (medium
protection against
picking)
X
AP Anti-panic func-
tion X
CO Comfort cylinder X
WP Waterproof - WP X X
SW Seawater-proof X
WN Network integ-
rated X X
SC SmartCard ver-
sion X
VR Shortened range X
DK Detachable knob X
DM Door Monitoring X
Refer to the current product catalogue to see which particular versions can
be combined with one another. Locking cylinders are also supplied in
different profiles to satisfy differences in different regions:
PROFILE LOCKING CYLINDER HALF CYLINDER
Digital Locking Cylinder 3061
(Manual)
5. Versions
17 / 54

Standard Euro profile
cylinder as per DIN
18252/EN1303
X X
Scandinavian Oval X
British oval X
Swiss Round X X
Locking Cylinder 3061s are also offered in mortise and rim cylinder models
for American door profiles.
5.1 FD version (Standard)
Locking Cylinder 3061 freely rotating on both sides.
The .FD double thumb-turn cylinder is available from a length of 30-30
mm.
5.2 HZ version (Standard)
The standard version of the half cylinder.
5.3 Half-cylinder (HZ) version (self-locking)
Variant of the half cylinder with self-locking by a spring-loaded cam with
fixed reset position. Due to the suspension and the chamfer on the cam,
locking without ID medium is possible by means of pressing. The main
application is e.g. the installation in swivel lever handles for switch and
distribution cabinets or server racks in computer centres.
5.4 ZK version
Design is similar to standard version but with access logging and time zone
control.
Access event logging
The locking cylinder logs up to 3,072 of the most recent access events
with the date, time and transponder ID (TID). The data can be read via
the network using the programming device.
Time zone control
TLocking Cylinder 3061 can be programmed in such a way that
authorized transponders are only authorized for access at specific
times. For G1, there are 5 (+1) time zone groups available per area (e.g.
outer perimeter) within the different time zone schedules while G2 has
100 (+1) such groups.
Digital Locking Cylinder 3061
(Manual)
5. Versions
18 / 54

5.5 version for steel and fire retardant doors
Design is similar to standard version but for doors with sturdy metal
sections, such as fire doors, or doors with highly protective shielding. This
version is recommended in areas with high interference fields, such as
server rooms, and for all metal doors. The FH version cannot be retrofitted.
If wired networks are used, we recommend using this cylinder version due
to its reduced projection.
Before a locking cylinder is installed into a fire/smoke retardant door, the
fire certification has to be checked first to ensure that conformity is in
place.
It must be ensured that any locking devices or sealing strips do not impede
the orderly operation of the MC.
5.6 TS version
Design as for standard version, but with the additional option of allowing
the cylinder to engage without an identification medium. This cylinder
version can be engaged mechanically with the aid of two buttons on the
inside thumb-turn. This means that no transponder is needed when the
user is on the internal. The cylinder will then engage for five seconds
(configurable) and the door can be opened or locked. Once this time
interval expires, the cylinder rotates freely again on both sides.
The .TS version cannot be retrofit.
5.7 MR option
Design is similar to standard version but the locking cam features fixed
points where it positions itself when disengaged. This version is particularly
suitable for very smooth-running locks with multi-point locking systems.
Please observe the lock manufacturer's declaration of conformity when
combining multi-point locks with a panic function.
5.8 MS version
The Locking Cylinder 3061 can be supplied with stainless steel or brass
colour finish (highly glossy thumb-turn covers).
5.9 SKG or VdS versions (SZ)
The Locking Cylinder 3061 is optionally also available as a VdS cylinder.
The additional mechanical security features ensure that VdS Classes AZ
and BZ or Class SKG*** are achieved. These versions cannot be combined
with the brass and WP versions. The VdS cylinder can only be supplied in
combination with access control (ZK) functions.
Digital Locking Cylinder 3061
(Manual)
5. Versions
19 / 54

NOTE
The profile cylinder must be protected with a VdS-approved burglar-resist-
ant class B or C door label. Such door plates conform to DIN 18257, Class
ES 2 or ES 3. The cylinder may not protrude more than 3 mm above the
door plate. The scope of burglary-resistant measures is based on the re-
spective national provisions.
This version is available as .MS, .FH and WN versions.
5.10 AP version
A cylinder with an anti-panic function must be fitted to all doors where the
lock's panic function may be adversely affected by the position of the cam.
This version contains an integrated spring mechanism which places the
locking cam in a non-critical position, meaning a panic lock's panic function
cannot be blocked.
In contrast to all other cylinders, the .AP type cylinder is fitted the other way
round with the thumb-turn containing the battery and the electronics
module installed on the outside (see diagram).
Unlike the standard anti-panic cylinder (AP), the inside thumb-turn of
which is permanently engaged, the inside thumb-turn for the freely-
rotating AP version (AP.FD) is disengaged mechanically and cannot be
engaged with an identification medium.
1. Inside thumb-turn
2. Recessed grip ring
3. Battery replacement key
4. Outside thumb-turn
The following aspects should be taken into consideration for doors along
rescue routes which have been installed after April 1, 2003 (exit devices as
per DIN EN 179 or DIN EN 1125): All Locking Cylinder 3061 models may be
used for all exit devices where their approval states that the Locking
Digital Locking Cylinder 3061
(Manual)
5. Versions
20 / 54