ABH 6100EO Series User manual

**
PATENT No. 6,196,599 & 5,730,478
US
R
CL
CLASSIFIED
U
c 2017 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R
ISSUED 06-08-17
6100EO-1-00.DWG
12 LATCH CAM
2
11
4
5
6
23
1
10
SQUARE
-OR-
ROUND
COVER
COVER
#8 x 3/4" FHWS
#10 STAR WASHER
LATCH
12-24 x 1-7/8" FHMS
8-32 x 3/8" FHMS
10-32 x 1/4" PAN HD. M.S.
PUSH OR PULL HANDLE ASSY
12-24 x 1/2" SEX BOLT
ADAPTER PLATE
.
82
12
11 1
2
10
9.
4
4
2
2
5
6
71
3
44
1
ITEM
1QTY
1PART DESCRIPTION
#12 x 1/2" PHSMS STAKING SCREWS
13 1
6100EO
PAGE 1 OF 3
6100EO SERIES EXIT ONLY PUSH/PULL HANDLE
INSTALLATION RETROFIT FOR 161 PREP
(NO ADDITIONAL THRU BOLTS REQUIRED)
DETAIL "A"
NOTE:
BEFORE MOUNTING PUSH AND PULL
HANDLES, CAM PIN MUST BE ROTATED
TOWARDS SIDE INDICATED BY ARROW
STAMPED ON THE BASE.
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. USES STANDARD 161 DOOR PREP.
3. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
HORIZONTAL
BACKSET
WITH 7"
HANDLE
BACKSET
HANDLE
HORIZONTAL
WITH 5" OR 7"
DOWN
HANDLES
UP
HANDLES
**
13
CAM SHAFT
STAKING SCREW HOLE
8
7
EXIT ONLY PLATE
1
INSTALLATION INSTRUCTIONS:
1. Door to be machined for standard 161 .
2. Install latch (item 12) using either #8 FHWS (item 11) or 8-32 FHMS (item 2) depending on door material type.
3. Before mounting adapter plate (item 6) & exit only plate (item 8), determine which side of the door will receive the push or pull handle
assembly (item 4) and the direction the handle will mount. Handle can be mounted up, down or horizontally.
4. Mount adapter plate (item 6) & exit only plate (item 8) to door with (2) 12-24 screws (item 5) thru door and latch to (2) 12-24 sex
bolts (item 7). tighten securely.
5. Before mounting handle assembly (item 4), cam pin must be rotated towards the correct side of the handle (see detail A).
6. Mount handle assembly (item 4) to adapter plate (item 6) with (4) 10-32 screws (item 3) with (4) star washers (item 10).
7. Test lock for proper operation. If latch bolt does not extend or retract freely because of any type of binding, loosen mounting screws
to adjust alignment of trim handle assembly (item 4) and re-tighten screws one at a time while checking latch bolt movement.
8. To prevent the handle assembly from possible twisting, which in turn can cause binding, determine which staking screw hole will be
used for the handle assembly (the staking screw installs on the staking screw hole location opposite the direction the handle is
mounted). Install staking screw using #12 PHSMS (item 13).
9. Place cover (item 1) over handle assembly (item 4) and secure with (2) 8-32 screws (item 2) on each side.

c 2017 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R6100EO-2-00.DWG
ISSUED 06-08-17
PAGE 2 OF 3
6100EO
13/16"
BEVEL EDGE DOOR
UNIVERSAL OR
SQUARE EDGE DOOR
BORE
5-3/8"
4-3/8"
6-5/8"
8-5/8"
5/32"
1-1/8"
C
L
LOCK
&
STRIKE
BACKSET
13/16" 2-1/4"
7"
5"
2-3/4"
3-3/4"
BACKSET
DEPTH OF BORE
DOOR LATCH PROVISIONS
DEPTH
OF
BORE CHART
SEE DEPTH OF
1-1/8" DIA. (MIN)
DRILL FOR #8
WOOD SCREW
(2 PLACES)
2-1/4"
13/16"
13/16"
BACKSET
#8-32
TAPPED HOLE
(2 PLACES)
1-1/8"
1" DIA. HOLE REQUIRED, 2 PLACES
"HOLE" IN REINFORCEMENT
2-1/8" DIA.
HOLE THRU
5/32"
REINFORCEMENT BY
DOOR MFG.
7"
5"
2-3/4"
3-3/4"
BACKSET
UNIVERSAL OR
SQUARE EDGE DOOR
BEVEL EDGE DOOR
1" DIA. HOLE
(THRU ALL
SUPPORTS)
C
L
LOCK
&
STRIKE
WOOD DOORMETAL DOOR
EDGE GUARD NOTE:
WHEN PREPPING THE
DOOR FOR THE BACKSET,
DETERMINE IF THE DOOR
WILL RECEIVE AN EDGE
GUARD. IF SO, THE EDGE
GUARD SHOULD BE
INSTALLED FIRST AND
THEN THE PREP FOR THE
LATCH BACKSET SHOULD
BE MEASURED FROM THE
OUTSIDE EDGE OF THE
EDGE GUARD.
ADA
RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
TO CENTER LINE
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT
VERIFY BACKSET
CENTER LINE
6100EO SERIES PUSH/PULL LATCH - DOOR PREP
2-1/8" DIA.
HOLE THRU
(VERTICAL OR HORIZONTAL MOUNTING SHOWN) (VERTICAL OR HORIZONTAL MOUNTING SHOWN)
DOOR PREP INFORMATION:
1. BACKSET DIMENSION FROM LOW EDGE OF BEVEL.
2. CENTER PUNCH ALL HOLES.
3. DRILL HOLES (FOR HOLLOW METAL DOORS,
DO NOT DRILL THRU. CENTER PUNCH & DRILL
HOLES FROM BOTH SIDES OF DOOR).
4. REINFORCEMENT MUST BE APPLIED ON METAL
DOORS AT THE SCREW LOCATIONS.
5. REINFORCEMENT TO BE SUPPLIED BY DOOR
MANUFACTURER. THE HANDLE ASSYS MUST BE
SUPPORTED. THE LATCH BOLT UNIT MUST BE
SUPPORTED AND CENTERED WITHIN 1/16" OF
THE CENTERLINE AT THE BACK END.

3/32"
DOOR STOP
MORTAR
GUARD
3-3/8"
(MIN)
1" (MIN)
REINFORCEMENT BY
FRAME MFG.
HALF DOOR THICKNESS
(MEASURED FROM STOP OR
SILENCER WHEN USED)
C
LLOCK & STRIKE
1-1/4"
+1/64
-0
1-1/16"
2-1/16"
2-1/16"
4-7/8"
3-3/8"
3-3/8"
+1/64
-0
#12-24
TAPPED HOLE
(2 PLACES)
LOCK
&
STRIKE
L
C
1" X 1-1/2" MIN CAVITY TO
ACCOMMODATE DUST BOX
C
L
LOCK
&
STRIKE
DRILL FOR #8
WOOD SCREW
(2 PLACES)
L
C
3/32"
27/32"
1-1/2"
1-1/8"
1-1/16"
1-1/16"
2-3/4"
HALF DOOR THICKNESS
(MEASURED FROM STOP OR
SILENCER WHEN USED)
c 2017 ABH Mfg., Inc.
printed in USA
O
Rwww.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224) ISSUED 06-08-17
6100EO-3-00.DWG
PAGE 3 OF 3
6100EO
WOOD FRAMEMETAL FRAME
THICKNESS
3. Mortise to required strike and box depth.
2. Center strike and mark screw positions.
1. Mark centerline of latch bolt on frame.
1-1/4
1-1/4
1-1/23-3/8 4-7/8
4-1/8
3/32
1/4
1/4 5/64
1-5/16
1-1/8 9/16
2-3/4
2-1/8
OF LATCH
L
C
(OR SILENCER)
EDGE OF STOP
1/2 DOOR
4. All dimensions in inches.
1/32
15/16
4-3/4
1-5/32
4-1/8
3-1/4 3-3/16
1"
1/16
3/16
1-11/16
1/2
PREP FOR #8 SCREW
1-3/16
2-1/4
1-11/16
1
1
1-11/16
1/2
21/32
1-3/16
3/16
1/16
9/64
2-1/4
1-11/16
1/32
9/16
1-3/16
1-5/32
61/64
2-1/8
2-11/16
1-1/4
PREP FOR #8 SCREW
PREP FOR #8 SCREW
1"
PREP FOR #12 SCREW
1-1/2"
DOOR STOP
6100EO SERIES PUSH/PULL LATCH - FRAME PREP
(ASA STRIKE SHOWN FOR EXAMPLE) ("T" STRIKE SHOWN FOR EXAMPLE)
LOCK & STRIKE
ASA STRIKE & DUST BOX "T" STRIKE & DUST BOX "D" STRIKE
601LB STRIKE
FRAME PREP: