Simplex SafeLINC 4100 User manual

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
4100 / 4120
FIRE ALARM SYSTEM
INSTALLATION INSTRUCTIONS
FOR CONTRACTOR
(LT0281)
Volume 2 of 3

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
ii
MANUFACTURER’S DETAILS
APPROVALS: AUSTRALIAN STANDARD AS1603.4
SSL CERTIFICATE OF COMPLIANCE NUMBER 127
The 4100 Fire Indicator Panel is manufactured by:
Simplex International Pty Ltd
140 Old Pittwater Road
Brookvale N.S.W 2100 Australia
ACN: 008 435 443
Phone: [phone]
Notice: The contents of this document is subject to change without notice
NOTICE
FIRST-TIME INSTALLERS OF SIMPLEX 4100+ FIRE ALARM PANELS
AFTER READING THE INFORMATION CONTAINED IN THIS MANUAL,
CALL YOU LOCAL SIMPLEX REPRESENTATIVE BEFORE
PROCEEDING TO CONNECT FIELD WIRING!
CAUTION
DO NOT APPLY AC OR BATTERY POWER TO THE 4100+ SYSTEM
(UNLESS IN THE PRESENCE OF A SIMPLEX TECHNICAL
REPRESENTATIVE).

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
iii
AMENDMENTS TO 4100 /4120 INSTALLATION MANUAL
ISSUE SECTION/PAGES AMENDED DATE AMENDED COMMENTS ECN No.
1 NIL 04-05-97 Original - File:
41M002.doc
RELATED DOCUMENTATION
This manual is part of a three volume set relating to the 4100/4120 Fire Alarm Panel. The
following lists the documentation relating to the 4100/4120 Fire Alarm Panel
Volume 1 4100/4120 Fire Indicator Panel - Operator Manual. This manual describes the
operating procedures for a typical 4100/4120 Fire Indicator Panel.
4100 Fire Indicator Panel Operator Manual - Part No/Document No: 4100-M001
4120 Fire Indicator Panel Operator Manual - Part No/Document No: 4100-M004
Volume 2 4100/4120 Fire Indicator Panel - Installation Manual. This manual describes the
procedures for installing and commissioning a typical 4100/4120 Fire Indicator
Panel.
Part No/Document No: 4100-M002
Volume 3 4100/4120 Fire Indicator Panel - Technical Manual. This manual contains technical
descriptions of the various components of a typical 4100/4120 Fire Indicator Panel .
Part No/Document No: 4100-M003

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
iv
TABLE OF CONTENTS
RELATED DOCUMENTATION.......................................................................................................................................iii
CONTRACTOR INSTALLATION INSTRUCTIONS ........................................................................................................1
INTRODUCTION..............................................................................................................................................................1
Supplied Documentation........................................................................................................................................1
INSTALLATION PROCEDURE .......................................................................................................................................2
1. Inventory the delivered equipment.....................................................................................................................2
2. Install the back box. ...........................................................................................................................................3
3. Install and tag all system wiring. ........................................................................................................................3
4. Install the peripheral devices and E.O.L. resistors.............................................................................................3
5. Remove the option bay door. (See Figure 4.)...................................................................................................4
6. Check and terminate all zone (ZN), MAPNET Loops (MAP A , MAP B) and signal (SIG) wiring.....................5
7. Check and terminate all remaining circuits (AC power, AUX, FB, City, MAPNET II®, etc.)...............................6
8. Dress the panel wiring........................................................................................................................................6
9. Install the option bay door..................................................................................................................................6
10. Call your local Simplex Branch Office (listed in the Yellow Pages) to install the printed circuit boards and
test the system.......................................................................................................................................................6
PROGRAMMER’S REPORT ...........................................................................................................................................7
1. General Information (see Figure 5)....................................................................................................................7
2. Card Summary by Location (see Figure 6)........................................................................................................8
3. System Point Summary (see Figure 7)..............................................................................................................8
3.1 Zone Name.................................................................................................................................................8
3.2 Address.......................................................................................................................................................8
3.3 Custom Label..............................................................................................................................................9
3.4 Point Type...................................................................................................................................................9
4. System Options Summary (see Figure 8)........................................................................................................11
5. Card Detail Report (see Figure 9)....................................................................................................................12
6. Annunciator Report (see Figures 10 and 11)...................................................................................................13
7. Digital Pseudo Point Summary (see Figure 11)...............................................................................................14
8. Analog Pseudo Point Summary (see Figure 12)..............................................................................................17
9. Point List Summary (see Figure 13) ................................................................................................................18
10. Point List Detail (see Figure 14).....................................................................................................................19
11. Options Detail Report (see Figure 15) ...........................................................................................................20
12. Network Interface Report (see Figure 16).....................................................................................................21
13. Custom Control Equation Listing (see Figure 17)..........................................................................................22
FIELD WIRING DIAGRAMS ..........................................................................................................................................23
BRIGADE CONFIGURATION AND CONNECTION......................................................................................................23

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
v
INSTALLATION CHECKLIST FOR SIMPLEX TECHNICAL REPRESENTATIVE.......................................................24
VISUAL INSPECTION ...................................................................................................................................................25
INSTALL PRINTED CIRCUIT BOARDS .......................................................................................................................25
CPU/MAIN POWER SUPPLY BOARDS WITH COMPONENTS..................................................................................29
1. Power-Up Procedures......................................................................................................................................29
2. System Test Procedures..................................................................................................................................30
2.1 Battery Test ..............................................................................................................................................30
2.2 Brigade Test.............................................................................................................................................30
2.3 Alarm Test.................................................................................................................................................30
2.4 Lamp Test.................................................................................................................................................30
2.5 Remounting Retainer................................................................................................................................30
APPENDIX A..................................................................................................................................................................32
TROUBLESHOOTING PROCEDURES ........................................................................................................................32
A. General Troubleshooting Information..............................................................................................................32
B. Troubleshooting Chart.....................................................................................................................................32
APPENDIX B..................................................................................................................................................................35
4100 Fault Messages....................................................................................................................................................35
1. CARD TROUBLES ..........................................................................................................................................35
2. BATTERY TROUBLES....................................................................................................................................37
3. EARTH GROUNDS .........................................................................................................................................38
4. ANNUNCIATOR TROUBLES..........................................................................................................................40
5. MAPNET TROUBLES......................................................................................................................................41
6. RUI TROUBLES .............................................................................................................................................43
APPENDIX C..................................................................................................................................................................44
GLOSSARY OF 4100 FIRE ALARM SYSTEM TERMS................................................................................................44

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
vi
FIGURES
FIGURE PAGE
1 System Hardware Envelope Label....................................................................................................2
2 Location of DIP Switches on Typical Device.....................................................................................3
3 Device Address Label.......................................................................................................................3
4 Removing the Option Bay Door........................................................................................................5
5 General Information Report..............................................................................................................7
6 Card Summary by Location Report...................................................................................................8
7 System Point Summary..................................................................................................................10
8 System Options Summary..............................................................................................................11
9 Card Detail Report..........................................................................................................................12
10 Local Annunciator Report................................................................................................................13
11 Digital Pseudo Point Summary..................................................................................................14-16
12 Analog Pseudo Point Summary......................................................................................................17
13 Point List Summary........................................................................................................................18
14 Point List Detail...............................................................................................................................19
15 Options Detail Report......................................................................................................................20
16 Network Interface Report................................................................................................................21
17 Custom Control Equation Listing.....................................................................................................22
18 Custom Terminal Wiring Identifiers.................................................................................................26
A1 Voltage Chart..................................................................................................................................33
TABLES
TABLE PAGE
1 MAPNET IIAddresses....................................................................................................................4
2 Acceptable Zone and Signal Circuit Meter Readings.........................................................................6
3 Printed Circuit Board Addresses.....................................................................................................27
4 All Expansion Cards........................................................................................................................27
5 24 Point Graphic I/O Card Pluggable Resistors...............................................................................28

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
1
CONTRACTOR INSTALLATION INSTRUCTIONS
* * * IMPORTANT * * *
THE INSTALLER IS RESPONSIBLE FOR SAFEGUARDING ALL 4100+ MATERIAL SHIPPED TO THE JOB SITE.
DURING SYSTEM INSTALLATION, STORE ALL 4100+ ITEMS (INCLUDING ALL DOCUMENTATION) IN A CLEAN,
DRY AND SAFE PLACE UNTIL NEEDED.
* * * * * * * * * * * *
NOTIFY APPROPRIATE PERSONNEL (BUILDING OCCUPANTS, FIRE DEPARTMENT, MONITORING FACILITY,
ETC.) IF AN EXISTING SYSTEM MUST BE SHUT DOWN WHILE THE 4100+ SYSTEM IS BEING INSTALLED.
INTRODUCTION
This publication provides a logical sequence of procedures to follow when installing a 4100+ system. Throughout this
publication, you are often referred to the documentation listed below. In such cases, notes describing use of the
documents will generally follow immediately after the reference.
Supplied Documentation
The envelope that contained this publication also contains the following documents:
•4100+/4120/UT Back Box Installation Instructions (Pub. No. FA4-21-203)
•Factory Documentation (packed in a clear plastic envelope)
•4100 Field Wiring Diagram (841-731)
•Field Wiring Diagrams, Smoke Detectors (841-687)
•Field Wiring Diagrams, MAPNET II®Devices (841-804)
•4100/4100+ Fire Alarm Operating Instructions (Pub. No. FA4-31-201)
Except for the last publication, all of the above documents are required for system installation.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
2
INSTALLATION PROCEDURE
NOTES:
A. Indexes for the 4100 Field Wiring Diagram are found on the first page of the document.
B. All wiring must be in accordance with local codes.
C. A page entitled “GENERAL WIRING PRECAUTIONS”is included in the 4100 Field Wiring Diagram.
If possible, proceed through the installation process in the sequence that follows.
1. Inventory the delivered equipment.
* * * IMPORTANT * * *
The contractor IS NOT responsible for inventorying or installing daughter cards, or for interconnecting panel
components.
•All cartons that contain daughter cards are to be opened, inventoried, and installed by Simplex personnel.
•In addition to the envelope that contained this publication and the material listed in the Packaging Information
section of the Factory Documentation, supplied material includes an envelope labelled System Hardware, as
shown in Figure 1.
SYSTEM
HARDWARE
OPEN CAREFULLY
748-200
SIMPLEX TIME RECORDER CO.
GARDNER, MA 01441 U.S.A.
570210-A
Figure 1
System Hardware Envelope Label

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
3
2. Install the back box.
•Use the 4100+/4120/UT Back Box Installation Instructions (Pub. No. FA4-21-203).
3. Install and tag all system wiring.
•See the SYSTEM POINT SUMMARY Report (Figure 7) and the appropriate page in the 4100 Field Wiring
Diagram (841-731).
4. Install the peripheral devices and E.O.L. resistors.
•See the Point Type column in the SYSTEM POINT SUMMARY Report for device type.
NOTES:
A. The 748-200 System Hardware envelope contains the required resistors.
•3.3K (monitor zone) resistors are colour coded orange, orange, red (and have a gold tolerance band);
10K (Notification appliance [signal] circuit) resistors are colour coded brown, black, orange (and also
have a gold tolerance band).
•Resistors other than those described above will be used by the Simplex Technical Representative
(T.R.) during installation checkout.
B. Wire peripherals in accordance with the appropriate 4100 Field Wiring Diagram (841-731).
•Wire a MAPNET II®device in accordance with the appropriate MAPNET II® Field Wiring Diagram
(841-804). Then, SET THE DEVICE’S ADDRESS SWITCHES (Figure 2).
C. A MAPNET II®device’s address is represented by the final digit(s) in the zone’s name.
Examples: The device that connects to a zone named M1-2 must have its switches set to address 2;
the device that connects to a zone named M1-117 must have its switches set to address
117.
•See Table 1 for a complete listing of MAPNET II®addresses.
D. Use a small screwdriver or ball point pen to set device address switches.
E. After setting the device address, mark the device’s address label (Figure 3) to agree with the address
switches.
Figure 2 Figure 3
Location of DIP Switches Device Address Label
on Typical Device

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
4
TABLE 1
MAPNET II®Addresses
SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8
ON OFF OFF OFF OFF OFF OFF OFF = ADDRESS 1 ON OFF OFF OFF OFF OFF ON OFF = ADDRESS 65
OFF ON OFF OFF OFF OFF OFF OFF = ADDRESS 2 OFF ON OFF OFF OFF OFF ON OFF = ADDRESS 66
ON ON OFF OFF OFF OFF OFF OFF = ADDRESS 3 ON ON OFF OFF OFF OFF ON OFF = ADDRESS 67
OFF OFF ON OFF OFF OFF OFF OFF = ADDRESS 4 OFF OFF ON OFF OFF OFF ON OFF = ADDRESS 68
ON OFF ON OFF OFF OFF OFF OFF = ADDRESS 5 ON OFF ON OFF OFF OFF ON OFF = ADDRESS 69
OFF ON ON OFF OFF OFF OFF OFF = ADDRESS 6 OFF ON ON OFF OFF OFF ON OFF = ADDRESS 70
ON ON ON OFF OFF OFF OFF OFF = ADDRESS 7 ON ON ON OFF OFF OFF ON OFF = ADDRESS 71
OFF OFF OFF ON OFF OFF OFF OFF = ADDRESS 8 OFF OFF OFF ON OFF OFF ON OFF = ADDRESS 72
ON OFF OFF ON OFF OFF OFF OFF = ADDRESS 9 ON OFF OFF ON OFF OFF ON OFF = ADDRESS 73
OFF ON OFF ON OFF OFF OFF OFF = ADDRESS 10 OFF ON OFF ON OFF OFF ON OFF = ADDRESS 74
ON ON OFF ON OFF OFF OFF OFF = ADDRESS 11 ON ON OFF ON OFF OFF ON OFF = ADDRESS 75
OFF OFF ON ON OFF OFF OFF OFF = ADDRESS 12 OFF OFF ON ON OFF OFF ON OFF = ADDRESS 76
ON OFF ON ON OFF OFF OFF OFF = ADDRESS 13 ON OFF ON ON OFF OFF ON OFF = ADDRESS 77
OFF ON ON ON OFF OFF OFF OFF = ADDRESS 14 OFF ON ON ON OFF OFF ON OFF = ADDRESS 78
ON ON ON ON OFF OFF OFF OFF = ADDRESS 15 ON ON ON ON OFF OFF ON OFF = ADDRESS 79
OFF OFF OFF OFF ON OFF OFF OFF = ADDRESS 16 OFF OFF OFF OFF ON OFF ON OFF = ADDRESS 80
ON OFF OFF OFF ON OFF OFF OFF = ADDRESS 17 ON OFF OFF OFF ON OFF ON OFF = ADDRESS 81
OFF ON OFF OFF ON OFF OFF OFF = ADDRESS 18 OFF ON OFF OFF ON OFF ON OFF = ADDRESS 82
ON ON OFF OFF ON OFF OFF OFF = ADDRESS 19 ON ON OFF OFF ON OFF ON OFF = ADDRESS 83
OFF OFF ON OFF ON OFF OFF OFF = ADDRESS 20 OFF OFF ON OFF ON OFF ON OFF = ADDRESS 84
ON OFF ON OFF ON OFF OFF OFF = ADDRESS 21 ON OFF ON OFF ON OFF ON OFF = ADDRESS 85
OFF ON ON OFF ON OFF OFF OFF = ADDRESS 22 OFF ON ON OFF ON OFF ON OFF = ADDRESS 86
ON ON ON OFF ON OFF OFF OFF = ADDRESS 23 ON ON ON OFF ON OFF ON OFF = ADDRESS 87
OFF OFF OFF ON ON OFF OFF OFF = ADDRESS 24 OFF OFF OFF ON ON OFF ON OFF = ADDRESS 88
ON OFF OFF ON ON OFF OFF OFF = ADDRESS 25 ON OFF OFF ON ON OFF ON OFF = ADDRESS 89
OFF ON OFF ON ON OFF OFF OFF = ADDRESS 26 OFF ON OFF ON ON OFF ON OFF = ADDRESS 90
ON ON OFF ON ON OFF OFF OFF = ADDRESS 27 ON ON OFF ON ON OFF ON OFF = ADDRESS 91
OFF OFF ON ON ON OFF OFF OFF = ADDRESS 28 OFF OFF ON ON ON OFF ON OFF = ADDRESS 92
ON OFF ON ON ON OFF OFF OFF = ADDRESS 29 ON OFF ON ON ON OFF ON OFF = ADDRESS 93
OFF ON ON ON ON OFF OFF OFF = ADDRESS 30 OFF ON ON ON ON OFF ON OFF = ADDRESS 94
ON ON ON ON ON OFF OFF OFF = ADDRESS 31 ON ON ON ON ON OFF ON OFF = ADDRESS 95
OFF OFF OFF OFF OFF ON OFF OFF = ADDRESS 32 OFF OFF OFF OFF OFF ON ON OFF = ADDRESS 96
ON OFF OFF OFF OFF ON OFF OFF = ADDRESS 33 ON OFF OFF OFF OFF ON ON OFF = ADDRESS 97
OFF ON OFF OFF OFF ON OFF OFF = ADDRESS 34 OFF ON OFF OFF OFF ON ON OFF = ADDRESS 98
ON ON OFF OFF OFF ON OFF OFF = ADDRESS 35 ON ON OFF OFF OFF ON ON OFF = ADDRESS 99
OFF OFF ON OFF OFF ON OFF OFF = ADDRESS 36 OFF OFF ON OFF OFF ON ON OFF = ADDRESS 100
ON OFF ON OFF OFF ON OFF OFF = ADDRESS 37 ON OFF ON OFF OFF ON ON OFF = ADDRESS 101
OFF ON ON OFF OFF ON OFF OFF = ADDRESS 38 OFF ON ON OFF OFF ON ON OFF = ADDRESS 102
ON ON ON OFF OFF ON OFF OFF = ADDRESS 39 ON ON ON OFF OFF ON ON OFF = ADDRESS 103
OFF OFF OFF ON OFF ON OFF OFF = ADDRESS 40 OFF OFF OFF ON OFF ON ON OFF = ADDRESS 104
ON OFF OFF ON OFF ON OFF OFF = ADDRESS 41 ON OFF OFF ON OFF ON ON OFF = ADDRESS 105
OFF ON OFF ON OFF ON OFF OFF = ADDRESS 42 OFF ON OFF ON OFF ON ON OFF = ADDRESS 106
ON ON OFF ON OFF ON OFF OFF = ADDRESS 43 ON ON OFF ON OFF ON ON OFF = ADDRESS 107
OFF OFF ON ON OFF ON OFF OFF = ADDRESS 44 OFF OFF ON ON OFF ON ON OFF = ADDRESS 108
ON OFF ON ON OFF ON OFF OFF = ADDRESS 45 ON OFF ON ON OFF ON ON OFF = ADDRESS 109
OFF ON ON ON OFF ON OFF OFF = ADDRESS 46 OFF ON ON ON OFF ON ON OFF = ADDRESS 110
ON ON ON ON OFF ON OFF OFF = ADDRESS 47 ON ON ON ON OFF ON ON OFF = ADDRESS 111
OFF OFF OFF OFF ON ON OFF OFF = ADDRESS 48 OFF OFF OFF OFF ON ON ON OFF = ADDRESS 112
ON OFF OFF OFF ON ON OFF OFF = ADDRESS 49 ON OFF OFF OFF ON ON ON OFF = ADDRESS 113
OFF ON OFF OFF ON ON OFF OFF = ADDRESS 50 OFF ON OFF OFF ON ON ON OFF = ADDRESS 114
ON ON OFF OFF ON ON OFF OFF = ADDRESS 51 ON ON OFF OFF ON ON ON OFF = ADDRESS 115
OFF OFF ON OFF ON ON OFF OFF = ADDRESS 52 OFF OFF ON OFF ON ON ON OFF = ADDRESS 116
ON OFF ON OFF ON ON OFF OFF = ADDRESS 53 ON OFF ON OFF ON ON ON OFF = ADDRESS 117
OFF ON ON OFF ON ON OFF OFF = ADDRESS 54 OFF ON ON OFF ON ON ON OFF = ADDRESS 118
ON ON ON OFF ON ON OFF OFF = ADDRESS 55 ON ON ON OFF ON ON ON OFF = ADDRESS 119
OFF OFF OFF ON ON ON OFF OFF = ADDRESS 56 OFF OFF OFF ON ON ON ON OFF = ADDRESS 120
ON OFF OFF ON ON ON OFF OFF = ADDRESS 57 ON OFF OFF ON ON ON ON OFF = ADDRESS 121
OFF ON OFF ON ON ON OFF OFF = ADDRESS 58 OFF ON OFF ON ON ON ON OFF = ADDRESS 122
ON ON OFF ON ON ON OFF OFF = ADDRESS 59 ON ON OFF ON ON ON ON OFF = ADDRESS 123
OFF OFF ON ON ON ON OFF OFF = ADDRESS 60 OFF OFF ON ON ON ON ON OFF = ADDRESS 124
ON OFF ON ON ON ON OFF OFF = ADDRESS 61 ON OFF ON ON ON ON ON OFF = ADDRESS 125
OFF ON ON ON ON ON OFF OFF = ADDRESS 62 OFF ON ON ON ON ON ON OFF = ADDRESS 126
ON ON ON ON ON ON OFF OFF = ADDRESS 63 ON ON ON ON ON ON ON OFF = ADDRESS 127
OFF OFF OFF OFF OFF OFF ON OFF = ADDRESS 64
NOTES:
A. Address zero (all switches turned OFF) is not a valid address.
B. Switch number 8 is never turned ON.
5. Remove the option bay door. (See Figure 4.)
a. (If applicable) Mark the top of the ribbon cable. Then pull the cable straight out of its connector.
b. Remove the hair-pin cotter pins (item 1) from the upper clevis pins (item 2). Then push the clevis pins
inward and lower the door.
c. Free the lower end of the retainer cable (item 3) by removing the screw and washer (items 4 and 5).
d. Remove the hair-pin cotter pins (item 6) from the lower clevis pins (item 7). Then push the clevis pins
inward and remove the door.
e. Store the door and its hardware in a safe, clean and dry place until all wires are terminated in the 4100+
panel.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
5
Figure 4
Removing the Option Bay Door
6. Check and terminate all zone (ZN), MAPNET Loops (MAP A , MAP B) and signal (SIG) wiring.
NOTES:
A. Use the CARD SUMMARY BY LOCATION Report (Figure 6) to determine the location of the
motherboard on which each specific circuit terminates.
•A stock-on “ADDRESS”label on each motherboard identifies that board’s number.
B. The above report is found within the computer printout portion of the Factory Documentation.
C. Use the terminal identifiers to find specific terminals.
•See Figure 18 (Custom Terminal Wiring Identifiers) for typical custom terminal wiring identifiers.
D. Check each circuit for voltages, shorts or opens as follows:
1. With the meter set on 300VAC, read the voltage across the circuit.
•Meter must read 0 volts.
2. With the meter set on 60VDC, read the voltage across the circuit again (this time in both directions).
•Meter must read 0 volts.
3. With the meter set on OHMS x 10 and its (+) and (–) leads connected to the circuit’s (+) and (–)
wires respectively, check resistance.
•Readings must compare favourably with those shown in Table 2.
•If reading indicates an open in a circuit that includes a smoke detector, make sure the detector
head(s) are properly mounted and seated.
–Circuits always read “open”(infinity) if detector power is absent and separately-powered
devices (four-wire smoke detectors) are involved.
E. Connect the wires to their terminals.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
6
TABLE 2
Acceptable Zone and Signal Circuit Meter Readings
Circuit Type Meter Reading
Style B (formerly Class B) Initiating Device (Zone) Circuit
From zone + to zone –(each zone) 3.3K ohms
From zone + to ground Infinity
From zone –to ground Infinity
Style D (formerly Class A) Initiating Device (Zone) Circuit
From zone + to zone –(each zone) Infinity
From zone + to ground Infinity
From zone –to ground Infinity
From zone + OUT to + IN Less than 50 ohms
From zone –OUT to –IN Less than 50 ohms
Style Y (formerly Class B) Notification Appliance Circuit (each signal circuit)
From + to ground Infinity
From –to ground Infinity
Resistance across circuit
In one direction 10K ohms
In opposite direction Less than 200 ohms
Style Z (formerly Class A) Notification Appliance Circuit (each signal circuit)
From + to ground Infinity
From –to ground Infinity
From + OUT to + IN Less than 50 ohms
From –OUT to –IN Less than 50 ohms
Resistance across circuit
In one direction Infinity
In opposite direction Less than 200 ohms
Shielding
Shield to ground Infinity
Shield to –Infinity
Shield to + Infinity
MAPNET II®Loops (ZAMs and IAMs)
From MAPNET II®+ to ground Infinity
From MAPNET II®–to ground Infinity
7. Check and terminate all remaining circuits (AC power, AUX, FB, City, MAPNET II®, etc.).
8. Dress the panel wiring.
•Use the tie wraps in the System Hardware envelope to neatly dress the panel wiring.
9. Install the option bay door.
10. Call your local Simplex Branch Office (listed in the Yellow Pages) to install the printed circuit boards
and test the system.
ONLY SIMPLEX REPRESENTATIVES ARE AUTHORISED TO APPLY
AC OR BATTERY POWER TO THE 4100+ SYSTEM.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
7
PROGRAMMER’S REPORT
The Programmer’s Report is used to identify peripheral connections within the panel and specifies system operational
data.
The 13 sections within the Programmer’s Report are shown in Figures 5 through 17, and explained in each section.
1. General Information (see Figure 5)
This section contains branch office required information. It details branch personnel involved with the system,
system power data, agency, and software information. The software revision must match the system CFIG chip
label for proper operation of the LCD display.
--------------------------------------------------------------------------------
XYZ BUILDING 1 GENERAL INFORMATION Page 1
909015J node:1 rev:1 05:20:54, THU, 08-MAY-97
--------------------------------------------------------------------------------
4100 Fire Alarm System GENERAL
Simplex Time Recorder Co. INFO
Node Number: 1
System Type: 4100+
Job Filename : 909015J
Job Title : XYZ BUILDING 1
Order Number :
Customer : ACME FIRE ALARMS
Customer Contact : JOE FLAME
Contractor :
Salesperson :
Branch Number : 909
Branch Location : PERTH
Programmed by : GF
Agency Approval : NONE
NFPA Standard : NONE
Standby Generator? : NO
Hours of Standby Battery :
Comments :
:
Job Rev : 1
Built Rev : 0
Built Date : ---
Current As Built
------- --------
Programmer Rev : 7.02 ---
System Defaults Rev : 77 ---
Database (DBF) Format : 79 ---
CFIG Format : 0 ---
Figure 5
General Information

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
8
2. Card Summary by Location (see Figure 6)
The Card Summary by Location shows the number of cards within the system. This page should be used to
verify delivery of system cards from the factory. It also shows a decimal card number which is the address for
that printed circuit board. Addresses 3 and 9 are shown below on Custom Terminal Wiring Identifiers.
--------------------------------------------------------------------------------
XYZ BUILDING 1 CARD SUMMARY BY LOCATION Page 3
909015J node:1 rev:1 05:20:54, THU, 08-MAY-97
--------------------------------------------------------------------------------
CARD
CARD LOCATION LISTING: LOCATION
LOCAL CONTROLLER UNIT:
DAUGHTER CARDS:
Card Card Type Zone Range
----- ---------------------------------------- -----------------
0 (7003) 4100+ Master Controller
1 (3003) 8 Pt, 3 Amp Relay w/ Feedback AUX3-10
2 (3003) 8 Pt, 3 Amp Relay w/ Feedback AUX11-18
3 (0112) 2120/RS232 Interface RS232-1, RS232-2
4 (6005) Power Supply/Charger
6 (0110) MAPNET Interface M1-1 - 127
7 (0110) MAPNET Interface M2-1 - 127
8 (0140) 4120 Network Interface
ANNUNCIATORS:
Annun Card Card Type Zone Range
----- ----- ---------------------------------------- -----------------
0 0 64 LED / 64 Sw Controller
5 (0301) 64 LED / 64 Sw Controller
NO REMOTE CARDS IN SYSTEM
Figure 6
Card Summary by Location
3. System Point Summary (see Figure 7)
The System Point Summary is of primary importance to the installer. Simplex personnel must provide this
information prior to installation. Call your local Simplex branch office, which is listed in the Yellow Pages, and
request this information be provided. This is used in conjunction with the Layout pages, to determine wiring
terminations and the information shown below.
3.1 Zone Name
Zone names reference the custom label to specific points for actual customer wiring. They include monitor
zones (ZNx), signals (SIGx), auxiliary relays (AUXx), 24 point I/O (PMx) and feedback (FBx) numbers.
Zones, signals, relays, feedbacks, etc., are shown in numerical sequence.
3.2 Address
Each printed circuit board requires a unique address. Address 0 identifies the master termination module.
Up to 119 addresses, one per printed circuit board, may be used in a system. Addresses may or may not
be in sequential order, but the report always starts with address 0. Two address labels are used for each
mother/daughter board combination. The mother board will have its unique address label next to the P.C.
board connector. The daughter board will have an identical label.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
9
3.3 Custom Label
The custom label identifies a location within the building or area, and contains additional information
concerning each circuit. Also included with the custom label is the corresponding zone name. This ties the
custom label to a zone name and allows the installer to identify where field wires are terminated, according
to zone name._____________________________________________________________
Examples: 6TH FLOOR NORTH WING EXHAUST FANS FB25
1ST FLOOR SOUTH WING VISUALS SIGNAL 2
3RD FLOOR EAST WING STROBES SIGNAL 40_
3.4 Point Type
This is the type of device (indicating appliance, initiating device, relays, etc.) connected to each circuit.
Each device type is abbreviated. An operational description may also be included in the abbreviation.
____________________________________________
Example: AHUM (Air Handling Unit Monitor)
PRI (Primary Elevator Capture)___
The installer should use the System Point Summary when marking wires to the 4100 panel. These
markings should include zones (ZNx+, ZNx--), signals (SIGx), etc., for each circuit within the system.
Marking each wire in this matter will facilitate termination and checking of the wiring in the 4100 panel.
NOTE: The SYSTEM POINT SUMMARY Report is found within the computer printout portion of the Factory
Documentation.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
10
--------------------------------------------------------------------------------
XYZ BUILDING 1 SYSTEM POINT SUMMARY Page 4
909015J node:1 rev:1 05:20:54, THU, 08-MAY-97
--------------------------------------------------------------------------------
POINT SUMMARY
System Point Summary (ascending by zone name): ZONE
Device Point PNIS
Zone Name Custom Label Type Type Code
--------- ---------------------------------------- ------- ------- -----------
AUX3 BATTERY TEST OUTPUT AUX3 RELAY
AUX4 SYSTEM FAULT AUX4 RELAY
AUX5 FIP BRIGADE ALARM AUX5 RELAY
AUX6 SIP BRIGADE ALARM AUX6 RELAY
AUX7 FIP ISOLATE BRIGADE SIGNAL AUX 7 RELAY
AUX8 FIP ALARM STAFF CALL AUX8 RELAY
AUX9 FIRE ALARM BELL AUX9 RELAY
AUX10 SIP ALARM STAFF CALL AUX10 RELAY
AUX11 SECURITY ACCESS O/RIDE AUX11 RELAY
AUX12 LEVEL 1 MDH OUTPUT AUX12 RELAY
AUX13 LEVEL 2 MDH OUTPUT AUX13 RELAY
AUX14 LEVEL 3 MDH OUTPUT AUX14 RELAY
AUX15 FIP ALARM TO SIP ISOLATE AUX15 RELAY
AUX16 SPARE AUX16 RELAY
AUX17 SPARE AUX17 RELAY
AUX18 SPARE AUX18 RELAY
FB3 ***** DOOR SWITCH ***** FEEDBACK PT FB3 ONOFF
FB4 AUX RELAY CARD 4 FEEDBACK PT FB4 ONOFF
FB5 AUX RELAY CARD 4 FEEDBACK PT FB5 ONOFF
FB6 AUX RELAY CARD 4 FEEDBACK PT FB6 ONOFF
FB7 AUX RELAY CARD 4 FEEDBACK PT FB7 ONOFF
FB8 AUX RELAY CARD 4 FEEDBACK PT FB8 ONOFF
FB9 AUX RELAY CARD 4 FEEDBACK PT FB9 ONOFF
FB10 FIP MCP FEEDBACK PT FB10 ONOFF
FB11 AUX RELAY CARD 2 FEEDBACK PT FB11 ONOFF
FB12 AUX RELAY CARD 2 FEEDBACK PT FB12 ONOFF
FB13 AUX RELAY CARD 2 FEEDBACK PT FB13 ONOFF
FB14 AUX RELAY CARD 2 FEEDBACK PT FB14 ONOFF
FB15 AUX RELAY CARD 2 FEEDBACK PT FB15 ONOFF
M1-1 LEVEL 1 SOUTH DIRECTOR OF NURSING Z1 SPHOTO SMOKE
M1-2 LEVEL 1 SOUTH STAFF RM Z1 SPHOTO SMOKE
M1-3 LEVEL 1 SOUTH LAUNDRY Z1 OHEAT HEAT
M1-4 LEVEL 1 SOUTH BEDSIT 12 BATHROOM Z1 OHEAT HEAT
M1-5 LEVEL 1 SOUTH BEDSIT 12 Z1 SPHOTO SMOKE
M1-6 LEVEL 1 SOUTH KITCHEN STORE RM Z1 SOHEAT HEAT
M1-7 LEVEL 1 SOUTH KITCHEN Z1 SOHEAT HEAT
M1-8 LEVEL 1 SOUTH KITCHEN Z1 SOHEAT HEAT
M1-9 LEVEL 1 SOUTH KITCHEN Z1 SOHEAT HEAT
M1-10 LEVEL 1 SOUTH DINING RM Z1 SPHOTO SMOKE
M1-11 LEVEL 1 SOUTH MALE TOILET Z1 OHEAT HEAT
M1-12 LEVEL 1 SOUTH FEMALE TOILET Z1 OHEAT HEAT
M1-13 LEVEL 1 SOUTH CLEANERS RM Z1 SPHOTO SMOKE
Figure 7
SYSTEM POINT SUMMARY Report
NOTES:
A. Custom label information tells you where the circuit goes.
B. At both ends of each circuit, tag wires with zone name and polarity (in cases where polarity applies).
•For example, SIG 3+ and SIG 3-.
C. T-tapping is permitted only for Style 4 (formerly Class B) MAPNET II®circuits.
All MAPNET II®circuits have zone names that begin with “M”.

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
11
4. System Options Summary (see Figure 8)
The System Options Summary lists all standard system operations. Enabled operations are shown with the word
“YES”.
--------------------------------------------------------------------------------
XYZ BUILDING 1 SYSTEM OPERATION Page 2
909015J node:1 rev:1 05:20:54, THU, 08-MAY-97
--------------------------------------------------------------------------------
OPTIONS
SUMMARY
Standard System Operations Enabled? Settings
----------------------------- -------- ------------------------------------
Alarm Silence Inhibit....... NO
Time Limit Signal Control... NO
System Trouble Reminder..... NO
Dedicated Waterflow Signals. NO
Sprinkler Supv. Operation... NO
Alarm Verification Setup.... NO
Individual Acknowledge ..... NO GLOBAL
Elevator Recall Operation... NO
Non-Steady Audible Evac Sig. NO
Non-Steady Visual Evac Sig. NO
Door Holder Operation....... NO
Expanded System Operations Enabled? Settings
----------------------------- -------- ------------------------------------
24-Hr Time/Date Format...... NO 12 HOUR
Coding Group Configuration.. NO
Audio Coding Configuration.. NO
Audio Option Configuration.. NO
Walk Test by Group.......... NO
Non-General Alarm Operation. NO
Pre-Programmed User Lists... YES *
Temperature in Centigrade... YES
Default Local Mode.......... YES
Paging Channel Selection.... NO
Other Selections Enabled? Settings
----------------------------- -------- ------------------------------------
Access Levels *
Non-Default Passcodes YES
City Connect Form ’C’ Dry Contact
Custom Control YES Program: 3, 4, 5, 6, 7
* Operation ENABLED. See Options Detail Report for full description.
Figure 8
SYSTEM OPTIONS Summary

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
12
5. Card Detail Report (see Figure 9)
The Card Detail Report shows detailed information regarding each printed circuit board as well as software cards
(pseudos) in the system. Custom information is shown for each type of card, such as card number, card address
(binary), circuits on the card, circuit types, custom labels, and coding information, if applicable.
--------------------------------------------------------------------------------
XYZ BUILDING 1 CARD DETAIL REPORT Page 12
909015J node:1 rev:1 04:39:17, WED, 14-MAY-97
--------------------------------------------------------------------------------
CARD No: 6 MAPNET
(0110) MAPNET Interface CARD
6
Dev. Pt.
Pt. Type Type Custom Label PNIS Code
--- ------ -------- ---------------------------------------- -----------
1 SPHOTO SMOKE LEVEL 1 SOUTH DIRECTOR OF NURSING Z1
2 SPHOTO SMOKE LEVEL 1 SOUTH STAFF RM Z1
3 OHEAT HEAT LEVEL 1 SOUTH LAUNDRY Z1
4 OHEAT HEAT LEVEL 1 SOUTH BEDSIT 12 BATHROOM Z1
5 SPHOTO SMOKE LEVEL 1 SOUTH BEDSIT 12 Z1
6 SOHEAT HEAT LEVEL 1 SOUTH KITCHEN STORE RM Z1
7 SOHEAT HEAT LEVEL 1 SOUTH KITCHEN Z1
8 SOHEAT HEAT LEVEL 1 SOUTH KITCHEN Z1
9 SOHEAT HEAT LEVEL 1 SOUTH KITCHEN Z1
10 SPHOTO SMOKE LEVEL 1 SOUTH DINING RM Z1
11 OHEAT HEAT LEVEL 1 SOUTH MALE TOILET Z1
12 OHEAT HEAT LEVEL 1 SOUTH FEMALE TOILET Z1
13 SPHOTO SMOKE LEVEL 1 SOUTH CLEANERS RM Z1
14 SPHOTO SMOKE LEVEL 1 SOUTH CORRIDOR Z1
15 SPHOTO SMOKE LEVEL 1 SOUTH CORRIDOR Z1
16 SPHOTO SMOKE LEVEL 1 CENTRAL CORRIDOR Z2
17 SPHOTO SMOKE LEVEL 1 CENTRAL VISITORS RM Z2
18 SPHOTO SMOKE LEVEL 1 CENTRAL RECREATION RM Z2
19 SPHOTO SMOKE LEVEL 1 CENTRAL RECREATION RM Z2
20 SPHOTO SMOKE LEVEL 1 CENTRAL CORRIDOR Z2
21 OHEAT HEAT LEVEL 1 CENTRAL TOILET Z2
22 SPHOTO SMOKE LEVEL 1 CENTRAL BEDSIT 1 Z2
23 SPHOTO SMOKE LEVEL 1 CENTRAL BEDSIT 2 Z2
24 SPHOTO SMOKE LEVEL 1 CENTRAL BEDSIT 3 Z3
25 SPHOTO SMOKE LEVEL 1 CENTRAL BEDSIT 4 Z3
26 SPHOTO SMOKE LEVEL 1 CENTRAL CORRIDOR Z3
27 SPHOTO SMOKE LEVEL 1 CENTRAL TREATMENT RM Z3
28 SPHOTO SMOKE LEVEL 1 CENTRAL PAN RM Z3
29 OHEAT HEAT LEVEL 1 CENTRAL TOILET Z3
30 SPHOTO SMOKE LEVEL 1 CENTRAL CORRIDOR Z3
31 OHEAT HEAT LEVEL 1 CENTRAL SWITCHBOARD CUPBOARD Z3
32 SPHOTO SMOKE LEVEL 1 CENTRAL SUN RM Z3
33 PHOTO SMOKE LEVEL 1 CENTRAL LIFT MOTOR RM Z4
34 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 5 Z5
35 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 6 Z5
36 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 7 Z5
37 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 8 Z5
38 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 9 Z5
39 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 10 Z5
40 SPHOTO SMOKE LEVEL 1 WEST BEDSIT 11 Z5
Figure 9
CARD DETAIL Report

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
13
6. Annunciator Report (see Figures 10 and 11)
The Local Annunciator Report is shown first (if applicable), followed by the Remote Annunciator Report (if
applicable). The first page of these reports shows the controller/card number, position, and the type of display
cards selected. The next pages will show the point, switch mode, reference address, reference custom label, and
the reference type. A typical Local Annunciator Report is shown in Figure 7.
--------------------------------------------------------------------------------
XYZ BUILDING 1 CARD DETAIL REPORT Page 11
909015J node:1 rev:1 04:39:17, WED, 14-MAY-97
--------------------------------------------------------------------------------
CARD No: 5 LED/SW
(0301) 64 LED / 64 Sw Controller CARD
UNIT No: 0 5
addr 00000101
sw1 12345678
CONTROLLER CARD CONFIGURATION DETAIL:
Controller
Card No Display Card Display Card Type
---------- ------------ -----------------------------
5 1 L403 - 8 Momen Sw/8 Red LED
2 L405 - 8 Momen Sw/16 Red-Yel LED
3 L405 - 8 Momen Sw/16 Red-Yel LED
4 L405 - 8 Momen Sw/16 Red-Yel LED
5 0409 - Blank Display Card
6 0409 - Blank Display Card
7 0409 - Blank Display Card
8 0102 - Battery Meters (amp/volt)
9 0409 - Blank Display Card
10 0409 - Blank Display Card
11 0409 - Blank Display Card
12 0409 - Blank Display Card
13 0409 - Blank Display Card
14 0409 - Blank Display Card
15 0409 - Blank Display Card
16 0409 - Blank Display Card
Figure 10
LOCAL ANNUNCIATOR Report

4100/4120 INSTALLATION MANUAL
Document No: 4100-M002 Issue 1.0
14
7. Digital Pseudo Point Summary (see Figure 11)
The Digital Pseudo Point Summary shows all digital pseudo points within the system. It also identifies the custom
labels, and pseudo type for each digital pseudo point within the system.
--------------------------------------------------------------------------------
XYZ BUILDING 1 DIGITAL PSEUDO POINT SUMMARY Page 10
909015J node:1 rev:1 05:20:54, THU, 08-MAY-97
--------------------------------------------------------------------------------
CARD No: 128 DIGITAL SUMMARY
256 Point Digital Pseudo P0 - P45
Point Custom Label Type PNIS Codes
------- ---------------------------------------- --------- -----------
P0 SYSTEM RESET KEY UTILITY
P1 ALARM SILENCE KEY UTILITY
P2 FRONT PANEL LAMPTEST CONTROL (ANNUNC. 0) UTILITY
P3 FIRE ALARM DETECT UTILITY
P4 GLOBAL ACKNOWLEDGE ENABLE UTILITY
P5 SET SERVICE PSEUDO VALUES UTILITY
P6 ALARM SILENCE UTILITY
P7 EXTRA CARD IN THE SYSTEM TROUBLE
P8 KEYPAD ACTIVE UTILITY
P9 SYSTEM OUT OF CQB’S TROUBLE
P10 CODED INPUT ACTIVE UTILITY
P11 UNACKNOWLEDGED FIRE ALARM EXISTS UTILITY
P12 UNACKNOWLEDGED SUPERVISORY EXISTS UTILITY
P13 UNACKNOWLEDGED TROUBLE EXISTS UTILITY
P14 SYSTEM DISABLED - PROGRAMMER DOWNLOAD TROUBLE
P15 CFIG RAM WRITE PROTECT MISSING (SW1-1) TROUBLE
P16 SMPL PROGRAM 0 - SYSTEM DEFAULT UTILITY
P17 SMPL PROGRAM 1 - DEFAULT AUDIO UTILITY
P18 SMPL PROGRAM 2 - SYSTEM OPTIONS (CODING) UTILITY
P19 SMPL 3 - TEST AND MESSAGE HOUSE KEEPING UTILITY
P20 SMPL 4 - GENERAL ALARM AND ACF CONTROL UTILITY
P21 SMPL- AZF 1 TO 24 ALARM EQUATIONS UTILITY
P22 SOUNDER EQUATIONS UTILITY
P23 PAGER EQUATIONS HOSTEL 1 & 2 UTILITY
P24 CODING GROUP 0 ACTIVE UTILITY
P25 CODING GROUP 1 ACTIVE UTILITY
P26 CODING GROUP 2 ACTIVE UTILITY
P27 CODING GROUP 3 ACTIVE UTILITY
P28 CODING GROUP 4 ACTIVE UTILITY
P29 CODING GROUP 5 ACTIVE UTILITY
P30 CODING GROUP 6 ACTIVE UTILITY
P31 CODING GROUP 7 ACTIVE UTILITY
P32 COLD START TROUBLE
P33 WARM START TROUBLE
P34 CITY DISCONNECT TROUBLE
P35 MANUAL EVACUATION SWITCH INPUT UTILITY
P36 ELEVATOR BYPASS TROUBLE
P37 DOORHOLDER BYPASS TROUBLE
P38 CONTROL POINT BYPASS TROUBLE
P39 SYSTEM EXECUTING FROM RAM TROUBLE
P40 AUTOMATIC DETECTOR RESET UTILITY
P41 MASTER FIRE ALARM ACK KEY UTILITY
P42 MASTER SUPERVISORY ACK KEY UTILITY
P43 MASTER TROUBLE ACK KEY UTILITY
P44 CODING BUS DISABLE SWITCH UTILITY
P45 DRILL SWITCH INPUT UTILITY