Simplex 4098-5217 User manual

579-1317 Rev 1
Sounder and Sounder Beacon Installation Instructions
*05791317A*
Cautions, Warnings, and Regulatory Information
READ AND SAVE THESE INSTRUCTIONS Follow the instructions in this installation manual. These instructions must be followed to avoid damage to
this product and associated equipment. Product operation and reliability depend upon proper installation.
DO NOT INSTALL ANY SIMPLEX™ PRODUCT THAT APPEARS DAMAGED Upon unpacking your Simplex product, inspect the contents
of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notify an authorized Simplex
product supplier.
ELECTRICAL HAZARD Disconnect electrical field power when making any internal adjustments or repairs. All repairs should be
performed by a representative or an authorized agent of your local Simplex product supplier.
STATIC HAZARD Static electricity can damage components. Handle as follows: Ground yourself before opening or installing
components. Prior to installation, keep components wrapped in anti-static material at all times.
Application Notes
The Wall variants are UL listed for General Signaling only but cannot be used in lieu of UL listed Notification Appliances in the area where they are
listed. The Base variants are not suitable for evacuation notification usage.
Introduction
The Addressable Sounder and Sounder Beacons operate with the 4100ES or 4010ES Fire Alarm Control Panels via their Loop Card's addressable loop
but must not be used with unauthorised third-party equipment. They are available in ceiling and wall mounting variants including an outdoor wall
version. The ceiling mounted variants provide a base for fitting an addressable Fire Detector. Alternatively a blanking cap should be fitted.
Summary of the range
Product Details
Base variant
4098-5217 Addressable Base Sounder
4098-5220 Addressable Base Sounder Beacon
Wall variant
4906-5210 Addressable Wall Sounder White
4906-5211 Addressable Wall Sounder Red
4906-5212 Addressable Wall Sounder Weatherproof
4906-5213 Addressable Wall Sounder Beacon White
4906-5214 Addressable Wall Sounder Beacon Red
4906-5215 Addressable Wall Sounder Beacon Weatherproof
Accessories
4905-5201 Blanking Cap for Sounder Bases
4905-5202 Conduit Adaptor for Sounder Bases
4905-5203 Shallow Surface Back Box for Indoor Wall Sounder Red
4905-5204 Shallow Surface Back Box for Indoor Wall Sounder White
firealarmresources.com

page 2 579-1317 Rev 1
Sounder and Sounder Beacon Installation Instructions
Product Details
4905-5205 Flush Backbox Adaptor for Indoor Wall Sounder
4905-5206 Deep Surface Back Box for Indoor Wall Sounder Red
4905-5207 Deep Surface Back Box for Indoor Wall Sounder White
General Information
4098-5217 4098-5220 4906-5210 4906-5211 4906-5212 4906-5213 4906-5214 4906-5215
Mounting
orientation
Ceiling Wall
Indoor/
Outdoor
Indoor Outdoor Indoor Outdoor
Weight (g) 146 g (5.15 oz) 154 g (5.4 oz) 182 g (6.4 oz) 182 g (6.2 oz) 358 g (12.6 oz) 194 g (6.8 oz) 194 g (6.8 oz) 372 g (13.1 oz)
Operating
temperature
(°C)
0°C to 70°C (-32°F to +158°F) 0°C to 49°C (32°F to 120°F) -25°C to +70°C
(-13°F to
+158°F)
0°C to 49°C (-32°F to 120°F) -25°C to +70°C
(-13°F to
+158°F)
Storage
temperature
(°C)
-25°C to +70°C (-13°F to +158°F)
Humidity Up to 95% non-condensing
Sounder
volume
settings
4 2
Isolator Yes
Beacon flash
rates
- 0.5 Hz and 1 Hz - - - 0.5 Hz and 1 Hz
Typical Sounder output at 1 metre (3.28 feet)
High volume 90 dBA 100dBA
Mid High
volume
80 dBA -
Mid Low
volume
70 dBA -
Low volume 60 dBA 90 dBA
Loop loading (with 4098-525X series addressable detector fitted to the base variants)
Sounder volume Beacon flash rate (if
applicable)
Wall sounder Wall sounder beacon Base sounder Base sounder beacon
OFF OFF 0.35 mA 0.35 mA 0.88 mA 0.88 mA
LOW OFF 3.2 mA 3.2 mA 3.0 mA 3.0 mA
HIGH OFF 8.6 mA 8.6 mA 4.8 mA 4.8 mA
HIGH 0.5 Hz - 11.2 mA - 8.0 mA
HIGH 1 Hz - 13.6 mA - 9.6 mA
Note: Please refer to the loop loading calculator for these units.
Address programming and configuration
Default address = 255. Set the address before installation using either the 850EMT or 801AP service tool with its ancillary lead. Remove the front cover
to access the programming port on wall devices. The 850EMT tool can be used to set the tone, flash rate and volume level. Refer to the document
125.515.058: 850 Engineering Tool User Manual for details.
firealarmresources.com

page 3 579-1317 Rev 1
Sounder and Sounder Beacon Installation Instructions
Installation
Dimensions
Weatherproof wall units Indoor wall units Base units
105mm/4.1in. 97mm/3.8in.
153mm/6in.
32mm/1.25in.
39mm/1.5in.
60mm/2.4in.
65mm/2.6in.
39mm/1.5in.
32mm/1.25in.
5
146mm/5.7in.
Figure 1: Sounder Beacon
89mm/3.5in. 40mm/1.6in.
138mm/5.43in.
60.3mm/2.37in.
135mm/5.3in.
Figure 2: Sounder
45mm/1.77ijn.
114mm/4.48in.
70mm/2.75in.
50mm/1.96in.
12
Figure 3: Base unit
1. Temporary park plunger and indicator (yellow)
for short circuit isolator.
2. Address flag holder.
Wiring
Wall variant wiring Base variant wiring Contact and Function
+-+-
Loop in Loop out
Screen
Figure 4: Wall variant wiring
Loop positive Loop positive
Loop negative Loop negative
Optional remote indicator
- -
L1
L
R
M
L2
Figure 5: Base variant wiring
L: Not used
L1: Positive line in and
out
L2: Negative line
(isolator in and out)
M: Negative line (isolator
in or out)
R: Remote LED out,
wired only if a remote
indicator is required.
Wiring notes
• All wiring must comply with local installation regulations and local fire system design requirements.
• Ensure all conductors are free of earths.
• Verify correct wiring and wiring polarity before connecting the devices to the addressable loop.
• Cables are to be selected in accordance with local standards, and with document 17A-02-D: MX Range of Addressable Controllers.
firealarmresources.com

page 4 579-1317 Rev 1
Sounder and Sounder Beacon Installation Instructions
Mounting and fixing instructions
Weatherproof wall units Indoor wall units Base units
These units are supplied with their own
back box and special front cover. A
sealing ring is supplied fitted on this
front cover. See item 1 in Figure 6.
1. Fix the back box to the wall. Drill
positions for glands on the top,
bottom, and sides, see item 2 in
Figure 6.
2. Slide the wall unit into place in the
front cover as shown and then push
down until it clips in.
3. Secure the front cover (including the
wall unit) to the back box with the
four supplied screws (M3.5 hex head)
using the supplied Allen key.
Note: To maintain the IP rating, use
suitably rated cable glands and sealant
as required.
1. Unclip the front cover from the wall unit. using the screwdriver
slot on the top.The front cover is hinged at the bottom of the
unit.
2. Use the two supplied screws to either fix the unit to the optional
back box (with knockouts for conduit connections) or to the
optional adaptor plate or to a back box with suitable mating
fixings.
3. Refit the front cover, engaging the clips on the bottom first.
4. Secure the front cover with either the supplied self-tapping
screw or nylon plug.
Note: If using the adaptor plate, a suitable recess is required for
the connector block protruding from the rear of the wall unit.
These units either fit directly to
the ceiling or to an optional ceiling
adaptor.The ceiling mounted variants
provide a base for fitting a fire detector.
Alternatively, a blanking cap is fitted.See
Figure 8. See Figure 10 for fitting the
locking pin. To remove a detector from a
base with a locking pin, complete these
steps:
1. Insert a suitable tool into the access
hole to depress the locking pin in the
detector cover.
2. Rotate the detector to remove.
These units can be used with the Ceiling
Tile Adapter (CTA) kit (517.050.060) by
using the CTA Adaptor Plate, CTA-AP
(517.050.058). Use the knock outs for
the cabling as required.
1
2
Figure 6: Fitting
weatherproof wall units
1
2
3
4
5
67
Figure 7: Indoor wall units
1. Single gang flush back box
2. A-BOX
3. S-BOX
4. D-BOX
5. M3.5 screw x 2
6. Self-tapping screw
7. Nylon plug
1
2
Figure 8: Fitting base units
1. A-CON
2. B-CAP
firealarmresources.com

page 5 579-1317 Rev 1
Sounder and Sounder Beacon Installation Instructions
Wall units Base units
1
2
3
4
Figure 9: Checking the gasket
1. Check that the gasket (item 1) is seated correctly before fitting the front cover.
2. Note the 'v' notch (item 2) on the upper side and gasket retained by thehooks on both sides (item 3).
3. Item 4 is the programming port.
Figure 10: Fitting
the locking pin
firealarmresources.com

579-1317 Rev 1
© 2019 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and are subject to change without notice. Additional listings may be applicable, contact your local Simplex®
product supplier for the latest status. Listings and approvals under Simplex Time Recorder Co. Simplex, and the product names listed in this material are marks and/or registered marks. Unauthorized use is strictly prohibited. NFPA 72 and
National Fire Alarm Code are registered trademarks of the National Fire Protection Association (NFPA).
firealarmresources.com