Simplex SafeLINC 4100U User guide

574-465
Rev. D
Smoke Management
Application Guide

Tyco Safety Products – Westminster, gratefully acknowledges the contributions of the following
organizations to this publication:
•American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.
(ASHRAE), Atlanta, GA.
•Andover Controls Corporation, Andover, MA.
•Center for Fire Research, National Engineering Laboratory, National Bureau of Standards,
U.S. Department of Commerce, Washington, DC.
•Integrated Systems, Inc., Brunswick, MD.
•National Fire Protection Association, Inc. (NFPA), Quincy, MA.
•U.S. Veterans Administration, Office of Construction, Washington, DC.
Acknowledgements
Acknowledgements

READ AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation
manual. These instructions must be followed to avoid damage to this product and associated
equipment. Product operation and reliability depend upon proper installation.
DO NOT INSTALL ANY PRODUCT THAT APPEARS DAMAGED.
Upon unpacking your product, inspect the contents of the carton for shipping damage.
If damage is apparent, immediately file a claim with the carrier and notify your distributor.
ELECTRICAL HAZARD -Disconnect electrical field power when making any internal
adjustments or repairs. All repairs should be performed by a representative or authorized agent of
your local Simplex®product supplier.
STATIC HAZARD - Static electricity can damage components. Therefore, handle as follows:
1. Ground yourself before opening or installing components.
2. Prior to installation, keep components wrapped in anti-static material at all times.
FCC RULES AND REGULATIONS – PART 15 - This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Cautions and Warnings
Cautions and
Warnings

©2004, 2011 SimplexGrinnell LP. All rights reserved.
Specifications and other information shown were current as of publication and are subject to
change without notice.
To further the science of Smoke Management, Tyco Safety Products hereby grants permission to
reproduce or transmit this reference document in any form or by any means, electronic or
mechanical, for the purpose of obtaining information on the science of Smoke Management.
We retain the rights of our respective trademarks.
Simplex, the Simplex logo, TrueSite, TrueAlarm, and IDNet are either trademarks or registered
trademarks of Tyco International Ltd and its affiliates and are used under license. NFPA 72 and
National Fire Alarm Code are registered trademarks of the National Fire Protection Association
(NFPA).
Walk Test™is protected by US Patent No. 4,725,818.
MAPNET II®addressable communications is protected by U.S. Patent No. 4,796,025.
IDNet™is patent pending.
TrueAlarm®Analog Detection is protected by U.S. Patent No. 5,155,468.
TrueAlarm®Detector Base is protected by U.S. Patent No. 5,173,683.
Windows®is a registered trademark of the Microsoft Corporation.
VESDA Scanner™and MiniVESDA™-50 are trademarks and the name VESDA®and
VESDA®E70-D are registered trademarks of Vision Systems.
All other logos are trademarks or registered trademarks of their respective companies.
Copyrights, Trademarks, and Patent Data
Copyrights
Trademarks
Patent Data

iii
Chapter 1 How Smoke Control Systems Work 1-1
Purpose ................................................................................................................... 1-1
Introduction.............................................................................................................. 1-1
In this Chapter ......................................................................................................... 1-1
Introduction.................................................................................................................. 1-2
Design Parameters.................................................................................................. 1-2
Design Concepts ..................................................................................................... 1-2
Controlling Smoke Movement ..................................................................................... 1-3
Basic Concept.......................................................................................................... 1-3
Creating Smoke Zones............................................................................................ 1-5
Causes of Smoke Movement .................................................................................. 1-6
Managing Smoke Movement................................................................................... 1-7
Principles of Smoke Control Systems ......................................................................... 1-8
System Types.......................................................................................................... 1-8
Maintaining System Integrity ................................................................................... 1-8
Smoke Control and Fire Control System Differences.................................................. 1-9
Separate System for Separate Goals...................................................................... 1-9
Designing a Smoke Control System.......................................................................... 1-10
Basic Goal ............................................................................................................. 1-10
How to Begin ......................................................................................................... 1-10
Engineering Responsibility .................................................................................... 1-10
Creating the Zone-By-Zone Smoke Control Plan.................................................. 1-10
Determining the Smoke Containment Pressure.................................................... 1-11
Separating Smoke Zones Properly........................................................................ 1-11
Selecting the Proper Fans and Duct Work............................................................ 1-11
Choosing the Proper Dampers.............................................................................. 1-12
Placing Air Inlets and Outlets ................................................................................ 1-12
Designing a Dedicated Smoke Control System ........................................................ 1-13
Introduction............................................................................................................ 1-13
About Stairtowers .................................................................................................. 1-13
Designing the Ideal Stairtower System.................................................................. 1-14
Ensuring Doors Can Open .................................................................................... 1-14
Controlling Pressure in a Stairtower...................................................................... 1-15
Elevator Smoke Control......................................................................................... 1-18
Detecting Smoke ....................................................................................................... 1-19
Introduction............................................................................................................ 1-19
Configuring and Monitoring a Smoke Control System .......................................... 1-19
Firefighter Smoke Control Station (FSCS) ............................................................ 1-19
Testing the System................................................................................................ 1-20
Related Documentation......................................................................................... 1-20
Chapter 2 Smoke Control Design Parameters 2-1
Introduction.............................................................................................................. 2-1
In this Chapter ......................................................................................................... 2-1
Table of Contents

iv
System Requirements ................................................................................................. 2-2
General Requirements............................................................................................. 2-2
Agency Requirements ............................................................................................. 2-2
System Design Parameters......................................................................................... 2-3
Verifying System Integrity During Non-Emergency Conditions............................... 2-3
Weekly Self-Test...................................................................................................... 2-3
Verifying System Integrity During Emergency Conditions....................................... 2-3
Automatic Activation................................................................................................ 2-3
Subsequent Automatic Activation............................................................................ 2-4
Automatic Activation By a Manual Pull Box............................................................. 2-4
Manual Operation.................................................................................................... 2-4
Automatic Override of Manual Activation ................................................................ 2-4
Chapter 3 Smoke Control System Components 3-1
Introduction.............................................................................................................. 3-1
In this Chapter ......................................................................................................... 3-1
Smoke Control System................................................................................................ 3-2
Smoke Control System............................................................................................ 3-2
4100U/4100ES Panels............................................................................................... 3-3
4100U/4100ES Panel............................................................................................. 3-3
4190 TrueSite Workstation and 24 Point I/O Graphic Interface.................................. 3-4
4190 TrueSite Workstation (TSW)........................................................................... 3-4
24-Point I/O Graphic Interface (4100-7401)............................................................ 3-4
Optional and Peripheral System Components............................................................ 3-5
Optional System Components................................................................................. 3-5
Peripheral Components........................................................................................... 3-6
Firefighter Smoke Control Station ............................................................................... 3-7
Firefighter Smoke Control Station (FSCS) .............................................................. 3-7
FSCS Ordering Information..................................................................................... 3-9
About the Fire Alarm Control Panel....................................................................... 3-10
Chapter 4 Installing the Smoke Control System 4-1
Introduction.............................................................................................................. 4-1
In this Chapter ......................................................................................................... 4-1
General Smoke Control Interconnections ................................................................... 4-2
Overview.................................................................................................................. 4-2
UUKL Addressable Monitor/Control Devices for 4100U/4100ES............................ 4-3
Reference Information............................................................................................. 4-4
Four Story Building Smoke Control Example.......................................................... 4-5
Dedicated Smoke Control System Wiring ................................................................... 4-6
Overview.................................................................................................................. 4-6
Dedicated Damper Control...................................................................................... 4-6
Dedicated Fan Control............................................................................................. 4-8
Non-Dedicated Smoke Control System Wiring Diagrams......................................... 4-10
Overview................................................................................................................ 4-10
Non-Dedicated Damper Control............................................................................ 4-10
Non Dedicated Fan Control................................................................................... 4-13

v
Chapter 5 Smoke Control System Programs 5-1
Introduction.............................................................................................................. 5-1
In this Chapter ......................................................................................................... 5-1
Smoke Control Program Requirements ...................................................................... 5-2
Introduction.............................................................................................................. 5-2
Emergency Operation.............................................................................................. 5-2
Automatic Program.................................................................................................. 5-2
Dedicated Smoke Control System Weekly Self-Test.............................................. 5-2
Dedicated Smoke Control System Weekly Self-Test.................................................. 5-3
Custom Control Programming Example.................................................................. 5-3
Equation 1: Start Self-Test ...................................................................................... 5-3
Equation 2: Turn ON Stair Pressure Fan................................................................. 5-3
Equation 3: Test Stairwell Air Pressure................................................................... 5-4
Equation 4: Reset Stair Pressure Fan to OFF......................................................... 5-4
Equation 5: End of Program.................................................................................... 5-4
Smoke Control System Custom Control Equations..................................................... 5-5
Introduction.............................................................................................................. 5-5
Smoke Control System CC Equation Summary...................................................... 5-5
Equation 1: Set Up Normal Conditions at Startup................................................... 5-7
Equation 2: Clear Faults on Startup ........................................................................ 5-7
Equation 3: Set Normal Conditions at Reset........................................................... 5-8
Equation 4: Set Normal Conditions at Reset........................................................... 5-8
Equation 5: Initialize Normal Conditions at Reset................................................... 5-9
Equation 6: Normal Conditions Complete After Reset............................................ 5-9
Equation 7: Smoke Control Initiate........................................................................ 5-10
Equation 8: Smoke Control Reset......................................................................... 5-10
Equation 9: Initiate Smoke Zone 1 ........................................................................ 5-10
Equation 10: Activate Smoke Control Zone 1........................................................ 5-11
Equation 11: Initiate Smoke Zone 2 ...................................................................... 5-11
Equation 12: Activate Smoke Control Zone 2........................................................ 5-12
Equation 13: Initiate Smoke Zone 3 ...................................................................... 5-12
Equation 14: Activate Smoke Control Zone 3........................................................ 5-13
Equation 15: Initiate Smoke Zone 4 ...................................................................... 5-13
Equation 16: Activate Smoke Control Zone 4........................................................ 5-14
Equation 17: Supply Fan Duct Smoke Alarm........................................................ 5-14
Equation 18: Stair Press Fan Duct Smoke Alarm ................................................. 5-14
Equation 19: Report TBL if Supply Fan Not ON.................................................... 5-15
Equation 20: Report TBL if Supply Fan Not OFF.................................................. 5-15
Equation 21: Report TBL if Exhaust Fan Not ON.................................................. 5-15
Equation 22: Report TBL if Exhaust Fan Not OFF................................................ 5-15
Equation 23: Report TBL if Stair Press Fan Not ON ............................................. 5-16
Equation 24: Report TBL if Stair Press Fan Not OFF ........................................... 5-16
Equation 25: Report TBL if Main EXH Damper Not Open..................................... 5-16
Equation 26: Report TBL if Main EXH Damper Not Closed.................................. 5-16
Equation 27: Report TBL if Main SUP Damper Not Open..................................... 5-17
Equation 28: Report TBL if Main SUP Damper Not Closed.................................. 5-17
Equation 29: Report TBL if Main RET Damper Not Open..................................... 5-17
Equation 30: Report TBL if Main RET Damper Not Closed .................................. 5-17
Equation 31: Report TBL If SUP Damper 1 Not Open.......................................... 5-18
Equation 32: Report TBL If SUP Damper 1 Not Closed........................................ 5-18
Equation 33: Report TBL If SUP Damper 2 Not Open.......................................... 5-18
Equation 34: Report TBL If Sup Damper 2 Not Closed......................................... 5-18
Equation 35: Report TBL If SUP Damper 3 Not Open.......................................... 5-19
Equation 36: Report TBL If SUP Damper 3 Not Closed........................................ 5-19
Equation 37: Report TBL If SUP Damper 4 Not Open.......................................... 5-19

vi
Equation 38: Report TBL If SUP Damper 4 Not Closed........................................ 5-19
Equation 39: Report TBL if EXH Damper 1 Not Open .......................................... 5-20
Equation 40: Report TBL If EXH Damper 1 Not Closed........................................ 5-20
Equation 41: Report TBL If EXH Damper 2 Not Open.......................................... 5-20
Equation 42: Report TBL If EXH Damper 2 Not Closed........................................ 5-20
Equation 43: Report TBL If EXH Damper 3 Not Open.......................................... 5-21
Equation 44: Report TBL If EXH Damper 3 Not Closed........................................ 5-21
Equation 45: Report TBL If EXH Damper 4 Not Open.......................................... 5-21
Equation 46: Report TBL If EXH Damper 4 Not Closed........................................ 5-21
Equation 47: Manual Control SUP AIR Damper 1 Open....................................... 5-22
Equation 48: Manual Control SUP Air Damper 1 Close........................................ 5-22
Equation 49: Manual Control SUP Air Damper 2 Open ........................................ 5-22
Equation 50: Manual Control SUP Air Damper 2 Close........................................ 5-22
Equation 51: Manual Control SUP Air Damper 3 Open ........................................ 5-23
Equation 52: Manual Control SUP Air Damper 3 Close........................................ 5-23
Equation 53: Manual Control SUP Air Damper 4 Open ........................................ 5-23
Equation 54: Control SUP Air Damper 4 Close..................................................... 5-23
Equation 55: Manual Control EXH Air Damper 1 Open ........................................ 5-24
Equation 56: Manual Control EXH Air Damper 1 Close........................................ 5-24
Equation 57: Manual Control EXH Air Damper 2 Open ........................................ 5-24
Equation 58: Manual Control EXH Air Damper 2 Close........................................ 5-24
Equation 59: Control EXH Air Damper 3 Open..................................................... 5-25
Equation 60: Manual Control EXH Air Damper 3 Close........................................ 5-25
Equation 61: Manual Control EXH Air Damper 4 Open ........................................ 5-25
Equation 62: Manual Control EXH Air Damper 4 Close........................................ 5-25
Equation 63: Manual Control Stair Press Fan ON................................................. 5-26
Equation 64: Manual Control Stair Press Fan OFF............................................... 5-26
Equation 65: Manual Control Main Supply Fan ON .............................................. 5-26
Equation 66: Manual Control Main Supply Fan OFF............................................. 5-26
Equation 67: Manual Control Main RET Air Damper Open................................... 5-27
Equation 68: Manual Control Main RET Air Damper Close .................................. 5-27
Equation 69: Manual Control Main Exhaust Fan ON ............................................ 5-27
Equation 70: Manual Control Main Exhaust Fan OFF........................................... 5-27
Equation 71: Manual Control Main SUP Air Damper Open................................... 5-28
Equation 72: Manual Control Main Sup Air Damper Close................................... 5-28
Equation 73: Manual Control Main EXH Air Damper Open................................... 5-28
Equation 74: Manual Control Main EXH Air Damper Close.................................. 5-28
Equation 75: Manual Control Clear Faults............................................................. 5-29
Equation 76: Master Key-Switch ........................................................................... 5-29
Equation 77: Turn SONALERT ON....................................................................... 5-30
Equation 78: Turn SONALERT OFF ..................................................................... 5-30
Chapter 6 Glossary of Terms 6-1
Introduction.............................................................................................................. 6-1
In this Chapter ......................................................................................................... 6-1
Glossary of Terms ....................................................................................................... 6-2
Glossary................................................................................................................... 6-2
Index............................................................................................................................ 6-1

vi
Before you start using the Smoke Management Application Guide, it is important to understand the
conventions used in this publication.
The following conventions are used to identify special names or text.
•Italic type indicates titles of publications, such as the Smoke Management Application Guide.
•Text enclosed in quotation marks indicates important terms or titles of chapters and sections
of the manual, such as “How to Use this Publication.”
•Bulleted lists, such as this one, provide you with information. They are also used to indicate
alternatives in numbered procedural steps.
•Numbered lists indicate procedures with steps that you must carry out sequentially.
About This Guide
Conventions Used

vii

1-1
The information in this guide serves to define the intended function of Smoke Control System
Equipment and also explain what operational and performance requirements are necessary for
equipment listed under the UL listing category of UUKL.
IMPORTANT: Smoke control systems must be designed to meet the custom
needs of a particular building and its occupants. This document
illustrates some basic, common smoke control applications, but is
not in lieu of a properly engineered smoke control system,
designed by a qualified Fire Protection Engineer.
This product is subject to change without notice. This document does not constitute any warranty,
express or implied. Tyco Safety Products reserves the right to alter capabilities, performance, and
presentation of this product at any time.
Many people are not aware that smoke is the major killer in fires. Smoke can travel to places in
buildings that are quite distant from the scene of the fire, threatening life and property. It can fill
stairwells and elevator shafts, blocking both evacuation and firefighting. Smoke control systems
reduce the number of smoke-related injuries and deaths. In addition, these systems reduce property
loss and damage caused by smoke.
Smoke control makes use of powered fans to produce air pressure that can control smoke
movement. Air pressure has been used in laboratories for over fifty years to prevent airborne
bacteria and poison gases from migrating from one area to another. It has also been used to control
the entrance of dust and other contaminants into computer rooms; and used in hospitals to prevent
the migration of harmful bacteria into sterile areas.
This chapter gives you an overview of smoke-control systems, including a discussion of the
driving forces of smoke movement, the principles of smoke control, and the concepts of smoke
control system design.
Refer to the page number listed in this table for information on a specific topic.
Topic See Page #
Introduction 1-2
Controlling Smoke Movement 1-3
Principles of Smoke Control Systems 1-8
Smoke Control and Fire Control Systems Differences 1-9
Designing a Smoke Control System 1-10
Designing a Dedicated Smoke Control System 1-13
Detecting Smoke 1-19
Chapter 1
How Smoke Control Systems Work
Purpose
Introduction
In this Chapter

1-2
A smoke control system can be designed to provide an escape route and/or safe zone.
However, all smoke control systems have the following design parameters:
•Air-flow paths through a building and leakage areas.
•Pressure differences across smoke control system boundaries.
•Door or vent openings in the boundary of a smoke control system.
•Airflow through openings in smoke control system boundaries.
The following factors can affect the design of a smoke control system:
System Flexibility:
System flexibility means using features that allow for easy adjustment of a particular system to
meet the demands of a given situation. For example, during the design and construction of a
building, leakage paths can be estimated. Thus, a smoke control system can only be designed to
provide theoretical protection from smoke. After the building is completed, the system must be
tuned to the actual pressure values. System flexibility is also useful when retrofitting smoke
control systems in existing buildings.
System Control:
A smoke control system should be designed to automatically activate, preferably by an alarm from
a smoke detection system in the fire zone. The advantage of this type of activation is that the
system is activated in the earliest stages of a fire. Smoke control systems should be activated after
the receipt of alarms from a properly designed smoke detection system.
Energy Conservation Management:
Energy conservation methods must be considered when designing a smoke control system.
A smoke control system must be designed to override the local heating, ventilation, and air
conditioning (HVAC) system, or energy management system in order to implement the desired
smoke control operations.
Use of Fire Suppression Systems:
Many fire protection schemes use automatic fire suppression systems. However, while the
functions of fire suppression and smoke control are both desirable, they are not intended to
substitute for each other.
Fire suppression systems are intended to limit the growth rate of a fire. Smoke control systems can
provide safe zones and tolerable conditions along exit routes, but can do little to control fire. In
addition to the obvious differences between the two systems, the way the systems interact must be
considered. For example, pressure differences and air flows are different in the various buildings
within a complex that is protected by a fire suppression system. A water spray from a sprinkler
might interfere with air flow to a smoke exhaust or an outside air pressure system or a smoke
control system could interfere with the performance of a gaseous agent (e.g., Carbon Dioxide or
Nitrogen) fire suppression system.
A general guideline is that the gaseous agent fire suppression system takes precedence over the
smoke control system. It is also desirable that the smoke control system be able to purge the
residual gases and smoke after the fire is extinguished, and replace them with fresh air. This is an
important life-safety consideration, since some fire-suppression gases are asphyxiates.
Introduction
Design Parameters
Design Concepts

1-3
Regardless of the method, the basic concept behind controlling smoke is to use differences in air
pressure to minimize the spread of smoke and, if possible, vent it from the building.
You cannot confine smoke by simply closing all access ways (such as doors and vents) to the
room that has the fire in it. Even with these passages closed off, smoke can disperse throughout a
building via cracks, holes made for pipes and electrical wires, and spaces around doors and
windows. Smoke is driven through these small openings by the expanding gases from the fire.
Smoke can also be driven onto other floors by the “stack effect,” which causes air to rise in
buildings. The stack effect is caused by the difference in the interior and exterior temperature of
the building. The figure below shows how smoke can disperse throughout a building:
Figure 1-1. Smoke Infiltrating Rooms Adjacent to the Fire
Continued on next page
Controlling Smoke Movement
Basic Concept
Area On Fire
Adjacent Room Adjacent Room
SMOKE
Second Floor
First Floor
Adjacent Room Adjacent Room
Adjacent Room

1-4
Since smoke is carried by the movement of air, you can stop the spread of smoke throughout the
building by lowering the air pressure in the area containing the fire and by raising the air pressure
in the surrounding areas and floors. The difference in air pressure (also called the “Air Pressure
Differential”) between the smoke-filled area and the surrounding areas acts as a barrier to the
smoke, pushing it back into the smoke-filled area. The figure below shows how this works.
FigureTag FD4-465-01
POSITIVE
AIR PRESSURE
POSITIVE
AIR PRESSURE POSITIVE
AIR PRESSURE
POSITIVE
AIR
PRESSURE
POSITIVE
AIR PRESSURE POSITIVE AIR PRESSURE POSITIVE AIR PRESSURE
NEGATIVE
PRESSURE
POSITIVE
AIR
PRESSURE
Figure 1-2. Applying Positive Air Pressure to Control Smoke
1. Lower the air pressure in a smoke-filled area by controlling the air flow into it and turning
ON the exhaust fans from the area to full capacity. This “Negative Air Pressure” technique
pulls the smoke out of the area and vents it outside of the building.
2. Pressurize the areas and floors surrounding the fire by turning OFF all exhaust systems
(including closing any exhaust dampers) and forcing supply air to those areas at full capacity,
creating zones of “Positive Air Pressure.” The air in the pressurized areas tends to leak into
the smoke zone, using the same cracks and holes that the smoke would use to get out. This
positive pressure airflow into the burning room keeps the smoke from spreading.
Continued on next page
Controlling Smoke Movement, Continued
Basic Concept

1-5
3. Turn OFF the air inlets and air returns of the areas that are neither being pressurized nor
depressurized (i.e., areas far away from the fire). Turning OFF the air return prevents the
smoke that is being vented into the return air system from coming into the smoke-free area.
In cases where there are large openings (such as an open doorway) between the area on fire
and an adjacent area, smoke can be confined by a large volume of air. Pumping large
amounts of air through the adjacent space creates a constant draft through the opening into the
smoke zone (as shown below).
CENTRIFUGAL FAN
Figure 1-3. Confining Smoke with a Large Volume of Air
The draft through the open space keeps back the smoke, confining it to the smoke zone. The
amount of air required to keep the smoke from penetrating the open space is quite large. Avoid
this type of situation when possible.
To contain smoke by using pressure, you must divide the building into “Smoke Control Zones.” A
floor or several floors of the building can be considered a single zone or a single floor can be
broken into a number of zones. A zone must be separated from other zones by smoke dampers,
airtight doors, and smoke-proof barriers.
When a fire occurs, the smoke control system can then pressurize all of the zones around the zone
where the fire initiated (called the “Fire Zone”), isolating the smoke to that single zone.
If the smoke control system is non-dedicated, the layout of the smoke control zones should take
into consideration the layout of the HVAC system. You should place multiple areas served by the
same HVAC controls in the same smoke control zone. Also, the smoke control zones must
conform to any fire control zones that have been established, because the smoke detectors are tied
into the fire detection system. Also, keeping the smoke control zones and the fire control zones the
same makes it easier to coordinate the two systems.
Controlling Smoke Movement, Continued
Basic Concept
Creating
Smoke Zones
A
IR
A
I
R
SMOKE
AIR

1-6
The following forces affect smoke movement:
Stack Effect:
When the outside air temperature is colder than the temperature inside a building, there is often an
upward movement of air within the building. This air movement is most noticeable in stairwells,
elevator shafts, electrical risers, or mail chutes, and is referred to as “Normal Stack Effect.” This
phenomenon is most noticeable in tall buildings during winter, but can occur in a single story
building as well.
When the outside air temperature is warmer than the temperature inside a building, there is often a
downward movement of air within the building. This air movement is referred to as “Reverse
Stack Effect.”
In a building with normal stack effect, the existing air currents can move smoke a considerable
distance from the fire origin. If the fire is below the neutral plane of the shaft (i.e., an elevation
where the hydrostatic pressure inside the shaft equals the hydrostatic pressure outside the shaft),
smoke moves with the building air into and up the shaft. Once above the neutral plane, smoke
flows out of the shaft into the upper floors of the building.
Buoyancy:
Smoke from a high temperature fire has buoyancy due to its reduced density. In a building with
leakage in the ceiling of the fire room, this buoyancy-induced pressure can produce smoke
movement. In a fire room with only one opening to the building, air flows into the room while hot
smoke flows out of the room. If the fire room has open doors or windows, the pressure difference
across these openings is negligible because of the large flow areas involved. However, for a
tightly-sealed room, the pressure differences due to expansion may be important.
Wind:
Wind can also have a pronounced influence on smoke movement within a building. The effect of
wind velocity on the air movement within a well-constructed building is minimal. However, the
effects of wind can become important for loosely-constructed buildings or buildings with open
doors or windows.
Frequently in fires, a window breaks. If the window breaks on the side of the building away from
the wind (the leeward side), the negative pressure caused by the wind vents the smoke from the
fire room. This can greatly reduce smoke movement within the building. However, if the broken
window is on the windward side of the building, the positive pressure of the wind can force the
smoke throughout the fire floor, and possibly to other floors as well. This event can endanger lives
and hamper firefighters as well. Wind induced pressures can be quite large and can easily
dominate building air movement.
Continued on next page
Controlling Smoke Movement, Continued
Causes of
Smoke Movement

1-7
HVAC System:
Before the development of smoke control systems, HVAC systems were shut down when a fire
occurred. This is because an HVAC system frequently transported smoke during building fires.
In the early stages of a fire, HVAC smoke transport can be a good thing. When a fire starts, the
HVAC system can transport the smoke to a location where people can smell it and be alerted to
the fire (although they may not know where the smoke is coming from). However, as the fire
progresses, the HVAC system transports the smoke to every area that it serves, endangering life in
all those places. To make matters worse, the HVAC system also supplies air to the fire, which aids
combustion.
Although shutting down the HVAC system prevents it from supplying air to the fire, this action
does not prevent the movement of smoke through the supply and return air ducts, air shafts, and
other building openings due to stack effect, buoyancy, or wind effect.
“Smoke Movement Management” includes all of the methods that can be used to modify and
control smoke movement for the benefit of the building occupants, firefighters, and for the
reduction of property damage. The use of barriers, smoke vents, and smoke shafts are traditional
methods of smoke management.
Barriers:
The effectiveness of barriers in limiting smoke movement depends on the leakage paths in the
barrier and on the pressure differential across the barrier. Holes where pipes penetrate floors or
walls, cracks around doors, and cracks in walls or between walls and floors are a few of the places
where smoke can leak through a barrier. The pressure differential across these barriers depends on
wind, buoyancy, stack effect, and the HVAC system.
Smoke Vents and Smoke Shafts:
The effectiveness of smoke vents and smoke shafts depends on their distance from the fire, the
buoyancy of the smoke, and the presence of other driving forces. In addition, when smoke is
sprinkler-cooled the effectiveness of smoke vents and smoke shafts is greatly reduced.
Elevator shafts in buildings have often been used as smoke shafts. The obvious problem with this
is that it prevents the elevator from being used for fire evacuation (because of the “piston effect”
of an elevator), and frequently allows the smoke to travel between floors. Specially designed
smoke shafts which have no leakage can be used to prevent the distribution of smoke to fire-free
floors.
In summary, the effectiveness of barriers in a traditional smoke management system is limited to
the extent that the barriers are free of leakage paths. Smoke vents and smoke shafts are limited by
the fact that the smoke must have sufficient buoyancy to overcome other forces that may be
present.
In the last few years, motorized fans have been used to overcome the limitations of the traditional
systems. The systems that employ these motorized fans are called “Smoke Control Systems.”
These Smoke Control Systems rely on creating air pressure differences and positive or negative
airflows to limit and control the movement of smoke and other noxious gases.
Controlling Smoke Movement, Continued
Causes of
Smoke Movement
Managing
Smoke Movement

1-8
Two types of smoke-control systems exist – Dedicated and Non-dedicated.
•Dedicated Smoke Control System: Is installed in a building for the sole purpose of
controlling smoke.
•Non-dedicated Smoke Control System: Uses parts of the building HVAC system to control
smoke.
In some cases, a building has both non-dedicated and dedicated systems. Non-dedicated systems
are used throughout the building for normal areas such as offices and manufacturing facilities.
Dedicated systems are used for special areas, such as elevator shafts, stairwells, stairtowers, and
other areas that need special smoke-handling techniques.
Smoke Control System products connect to HVAC equipment to form a system for controlling the
flow of smoke during a fire condition. Smoke-control systems are designed, installed, and
maintained so that a system remains effective and provides a “Tenable Environment” during
evacuation of the protected areas. A “Tenable Environment” as defined in NFPA 92A, is an
environment in which the quantity and location of smoke is limited or otherwise restricted to allow
for ready evacuation through the space.
A major concern with any emergency signaling system, whether burglary, fire, or smoke control,
is maintaining system integrity. This task is traditionally accomplished by electrical supervision of
wiring. However because the proper operation of the fans and dampers connected to the output
circuits may involve mechanical controls and pneumatic controls, as well as electrically-actuated
parts, end-process verification is provided. The end-process verification is provided to alert the
firefighter/operator that the fan or damper has operated in response to an automatic or manual
command issued during an emergency condition. While end-process verification confirms
operation during an emergency condition, system integrity during a non-emergency
(normal supervision) conditions is checked differently depending on whether the equipment is
non-dedicated or dedicated.
The operability of the non-dedicated smoke-control equipment is verified by the "comfort level" in
the areas that are served by the equipment. In other words, if the HVAC equipment is not
functioning properly, the building occupants are soon made aware of this and the problem can be
solved.
The operability of the dedicated smoke control equipment is verified by an automatic self-test that
is performed on a weekly basis.
Principles of Smoke Control Systems
System Types
Maintaining
System Integrity