SINED SOFFIONEDOCCIA-LED-1 User manual

SHOWER HEADS
USE AND MAINTENANCE MANUAL
SOFFIONEDOCCIA-LED-1 - 4F127
The photo is only indicative. The actual product may look slightly different in color.

USE AND MAINTENANCE MANUAL
This manual is an integral part of the product purchased. It contains important information for the installation
and use of the product. Before using the product, carefully read the instructions and in particular the safety
warnings. Failure to follow the instructions and warnings can cause serious damage to the person and the
product. The instructions provided are based on the rules and regulations valid in the European Union. For
other countries, please comply with the specific provisions in this area. eep instructions in case of future
need and hand them over to third parties.
INTENDED USE
Use the product only as described in the instructions. Any other use can cause damage to things or even to
people. This product is not a toy. The manufacturer or seller assumes no responsibility for any damage
resulting from incorrect use or not in accordance with the declared intended use.
Safety Warning
Read carefully and re pect all warning and in truction . Failure to comply with them can re ult in damage
to property, eriou per onal injury or even death. The e warning , in truction and product afety
provi ion include many, but not all, po ible ri k and hazard . It i recommended to pay attention and
correctly a e all dangerou ituation . Incorrect u e of the product could al o cau e life threatening.
Attention! Any repair work mu t be carried out exclu ively by qualified per onnel to avoid po ible
danger . If nece ary, contact a qualified technician. In the event of elf-repair , improper a embly or
mi u e, liability and warranty claim lap e. Only pare part that corre pond to the original product data
can be u ed for repair .
WARNING! Danger to children and people with reduced phy ical, en ory or mental abilitie or lack of
experience and knowledge: Children hould not play with thi product. Cleaning hould not be carried out
by children or people with reduced phy ical, en ory or mental abilitie .
NOTE: Ri k of damage! The product may be damaged by improper u e.
Content control
WARNING! Danger of damaging the product! If the packaging is opened without proper attention with a
sharp knife or other sharp tools, the contents may be damaged. Opening the package, therefore, be very
careful!
Check that the product and the individual components are intact and not damaged. Otherwise, do not use
the product and contact the seller immediately.
The model shown in the installation steps may differ from the one in the package. However, the connections
and installation steps remain the same.
In tallation

WARNING: Thi hower head i de igned to operate with a water pre ure of 20-80 p i (corresponding to
approx. 1.5 to 5.5 bar): If the water pressure is less than 20 psi, the built-in hydraulic generator cannot
generate enough pressure to operate the system. Pressure above 80 psi may damage the shower head.
Assembly and assembly of the shower head must be carried out by experienced people or by your trusted
plumber.
It is advisable to cover the base of the shower to avoid losing any component of the shower head.
Before starting the installation close the supply of both cold and hot water. Remove the existing shower
head, beingcareful not to unscrew the arm. Before installing the new shower head
, purge the pipes to remove any debris that may be in the system Before installing the
shower head make sure that the rubber washer is positioned correctly. When installing the shower head
tighten
by hand. Do not tighten too tightly. Do not u e a key or plier . Overtightening fittings compromises
system integrity.
Utilization
This type of shower head is controlled with a simple wave of the hand.
The color of the LEDs changes automatically depending on the temperature and water
COLD BLUE - temperature below 27°C
WARM GREEN - temperature between 27 and 41°C
RED very hot - temperature over 41°C

For people of different heights: change the direction of the sensor

PROBLEMS AND SOLUTIONS
No water comes out of the shower head
a) check the correct positioning of the washer
b) check that there is only one washer in the pivot
head
Low water pressure or no
jet
a) clean the shower head with vinegar/water
solution (see cleaning instructions)
b) clean the filter
c) water pressure less than 20 psi
Leakage at connection between hose and pin head
a) check that only one washer is positioned above
the filter
Cleanline
 U e only oft cloth and hot water and oap
 Do not use aggressive, corrosive or abrasive detergents
To ensure good performance clean the water filter regularly
 To access the filter you need to remove the shower head from the tube
 Rinse the filter under running water for a few minutes until it is cleaned of all impurities
 You can use a tenti toothbrush to gently remove any mineral deposits
 Reposition the filter and reinstall the shower head.
Guarantee
SINED products have a 2-year warranty from the date of purchase for defects in materials and
workmanship.
 Components subject to wear are excluded from the warranty
 Damage due to incorrect assembly, improper use and incorrect maintenance (e.g. use of
inappropriate detergents) is not covered by the warranty.
 Damages deriving from the use of non-original spare parts are not covered by the warranty.
 Any damage resulting from interventions not performed by specialized technicians is not
covered by the warranty.
 Damage due to frost, limescale or other impurities inside the shower is not covered by the
warranty.
In the presence of problems covered by warranty, the product must be returned to the seller.
 The product must be carefully packaged and complete with all its parts and accessories;
 The reason for the return must be described in detail and proof of purchase (invoice or
receipt) must be provided;
 The shipping costs of the return are charged to the buyer;
 The returned product will be checked at the seller's premises and repaired or replaced at
the sole discretion of the seller.

Produzione: M8 IMP & EXP CO., LTD
Address: No 5, Longxi Industrial Area
Yuhuan, Zhejiang, CHINA
Made in China Imported to Italy by M.P.C. srl - Via Tortona, 21 - 20126 Milan Italy Tel [phone] e-
mail [email protected] website www.sinedtechnology.com
The SINED trademark and the SINED logo are registered by SINED VENTAS ONLINE S.L.U. EUTM 018196373