Kohler K-13073T User manual

-1-
INSTALLATION INSTRUCTIONS
MIRRORED CABINET
K-13073T
()
MIRRORED CABINET W/DEFOGGER
K-13073T-D
MIRROR
K-13079T
METALLIQUE
, 2010
Copyright Kohler China Ltd., 2010
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation . This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information-
Before installation carefully inspect the new fixture for any
signs of damage.
Tempered glass cannot be cut.
Don't use acidic or alkalic cleaners or
alcohol to clean the wooden surface. Use a dampened
cloth to clean.
please leave instructions for the
consumer.
WARNING: Risk of injury or product damage.
WARNING:
·
·
·
·
-
PARTS
Parts supplied with your cabinet. (For cabinet body and door
replacement, call customer service with model number.) Be
sure to check the cardboard supports in the carton, glass
parts are packed in them.
13-1 528437
1132363-T01-B

-2-
Mirrored Cabinet
ACCESSORIES LISTACCESSORIES LIST
Screws GB/T818-2000 S/S M4 12
M4 12
X8
Screws ST3.5 35
ST3.5 35
X4
Screws ST3.5 35
ST3.5 35
X4
Side Mirrors
X2
Side Kits Brackets
X4
Wall Anchors
X4
Wall Anchors
X4
Snap-in Pins
X8
Mirror
K-13073T/K-13073T-D
ROUGHING-IN
UNIT : mm
489
762
129
99
Mirrored Cabinet
Caps of Screw
X4
Hole Plugs
X40
Foam Tape
X8
Top Clips
X2
431mm Mounting Bar
431
X1
Glass Shelves
X3
Half Sink-Screw S/S M3.5X10
M3.5X10
X4
1132363-T01-B

-3-
K-13079T
INSTALLATION
NOTE
·
·
The cabinet has two ways of installation:
Recessing mounting.
Surface mounting.
Refer to the following instruction for mirror installation.
·
·
489
762
Mirror
STEP
1
RECESSING THE MIRRORED CABINET INTO THE WALL
The Vertical installation changes the width of the roughout. Please refer to the picture below.
468mm for Models
468mm
Screws ST3.5 35
ST3.5 35
745mm high
745mm
Fig. 1 1
1132363-T01-B

-4-
STEP
2
Install screws through holes in mirrored cabinet as shown in Fig.1, 2
DO NOT OVER- TIGHTEN!
Use s .
Note:
12
crews ST3.5 35
ST3.5 35
Fig. 2 2
Top View
Stud and wall surface
Install dome caps over screws
Mirrored cabinet flange fits flush against wall
SURFACE MOUNTING THE MIRRORED CABINET ON A WALL
NOTE:
Installing the mirrored cabinet on a wall without the door
attached can make installing easier for one person. Do not
mount the doors until the boxes is in or on the wall.
Fig. 3 3
STEP
1
As shown in Fig 3, drill two 2- 5mm holes
in bottom mounting bar at indent location,
then drill 4- 6mm holes in wall at locations
shown in Fig 3, insert wall anchors.
35
46
Screws ST3.5 35 & Wall anchor
ST3.5 35
The highest point of table
Drill holes 2- 5
2- 5
Drill holes
4- 6mm
4- 6mm
Drill holes 2- 5
2- 5
Drill holes
4- 6mm
4- 6mm
20
750
320
1132363-T01-B

-5-
1051705-T01-A
STEP
3
Fig. 5 5
Apply foam tape to side kit bracket
DO NOT PEEL RELEASE LINER UNTIL YOU HAVE TEST FIT THE SIDE KITS ON THE MIRRORED CABINET!
·
·
Peel tape from sheet, leave liner on.
Apply as shown to side kit brackets, be sure they are clean and dry.
·
STEP
2
Fig. 4 4
Top clips slide into this screw
channel from center opening.
Top of cabinet frame member
2 Top clips
2
WALL
Sit the mirrored cabinet on the mounting bar, then lower and tighten the
screws into place, as shown in Fig.4.
4
Screws ST3.5 35 & Wall anchor
ST3.5 35
Top clip for
surface mount
2 per cabinet
1132363-T01-B

-6-
STEP
4
STEP
5
Fig. 6 6
Fig. 7 7
Fig. 8 8 Fig. 9 9
!
!
!
!
Attach the side kit brackets to the cabinet as shown in
Fig.6.
Test fit the side kits, then clean the back of the side kits
with rubbing alcohol.
Peel the release tape from the brackets and apply the
side kits, push firmly to set.
Cover the screw heads with the screw caps.
6Align top of side kit with top of flange
Screws ST3.5 35
self thread into
Side Kit brackets
2 pieces
762mm high
762
Side kit bracket
(Fits tight under the
flange of mirrored
cabinet)
()
Side kit brackets
Door adjustments
!
!
!
7-A 8
7-B 9
()
This screw releases the door from the cabinet and
allows up and down adjustment. Fig.7-A & 8.
These screws allow you to plumb the door as shown
in Fig.7-B & 9.
The screws you use for attaching the hinges.
(Supplied with hinges)
B
A
1132363-T01-B

-7-
STEP
6
Push/twist the pins into place & Fill the remaining holes with the plugs
!
!
Push one side of the shelf into the left or right clips.
Snap the shelf down into the opposite side. If the shelf is too tight, repeat the process from the other side.
&
STEP
7
A
B
Fig. 10 10 Fig. 11 11
Fig. 12 12
The step is only for the installation of defogger. See Fig 12,
external power supply.
(220V/50HZ)
220V/50HZ
1132363-T01-B

-8-
1.
2.
3.
4.
5. .
6. .
7.
USER MAINTENANCEUSER MAINTENANCE
Warn! Risk of product damage.
1.
2.
3.
4.
5. The mirrored cabinet door and interior are constructed of
mirror and aluminum. Use only a damp cloth to clean.
Spray the cloth, not the mirror when cleaning. Mirrors are
damaged by the use of ammonia or vinegar based
cleaners. Rubbing alcohol can be used for stubborn stains
6. Use no abrasive cleansers on any part of the mirrored
cabinet.
7. The white frame should be cleaned with a damp cloth only.
Many cleansers contain abrasive and chemical substance
which is not suitable for cleaning stainless steel, enamel,
plating or plastic products. You may use mild cleansers or
soaps to clean the surfaces. Wipe any splashes of cleaner
solutions from the surface with clean soft cloth.
Maintain ventilation in the bathroom, and separate the dry
area from the damp one if conditions permit. Try to open
the door and windows of the bathroom and maintain good
ventilation.
Kohler mirrored cabinet are dealt with strict procedures for
damp-proof, whose good damp-proof function ensures
good performance even in bathroom of huge humidity. Yet
do not splash and pour water directly on the mirrored
cabinet. Make sure that the bathroom is not over damp
and wipe any splashes from surfaces immediately.
Maintenance of door board: Clean and wipe door board
regularly, and wipe the condensation vapor with dry and
soft cloth.
.
MIRROR
Fig. 13 13
STEP
1
See Fig.12, drill holes on the wall insert the wall
anchors, fix the wall bracket of mirror and then
hang the mirror to the bracket.
12
Screws ST3.5 35 & Wall anchor
ST3.5 35
Drill holes
4- 6mm
4- 6mm
500
388
1132363-T01-B