Sinoboom GTTZ10EJ User manual

GTTZ10EJ/ML10EJ/ML340EJ
Operation
Manual
Part No.509002100002
Rev: A
Nov. 2020
GTJZ
0608E (2132E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
GTJZ
0808E (2732E)
长沙市宁乡高新技术产业园区金洲大道东
128 号
0731-87116111 hr@sinoboom . c om . cn ww w .sinoboom . c om . cn
Al w ays F or B e t t er A cc ess Solution s
我们一直在追求新的高 度
尺寸 ：
210×285mm
20mm
20mm
产品说明书
PRODU C T MAN U AL

Operating, servicing and maintaining this vehicle or
equipment can expose you to chemicals including engine
exhaust, carbon monoxide, phthalates, and lead, which
are known to the State of California to cause cancer and
birth defects or other reproductive harm. To minimize
exposure, avoid breathing exhaust, do not idle the engine
except as necessary, service your vehicle or equipment in
a well-ventilated area and wear gloves or wash your
hands frequently when servicing. For more information
go to: www.P65warnings.ca.gov.

Please contact us:
Website : www.sinoboom.com
E-mail : [email protected]
Sales Tel : [phone]
Service Tel : [phone]
Address : No.128, East Jinzhou Avenue, Ningxiang High-tech Industrial Park, Changsha,
Hunan, China
Zip Code : 410600
Copyright © Hunan Sinoboom Intelligent Equipment Co., Ltd. All Rights Reserved
The final interpretation right of this manual belongs to Hunan Sinoboom Intelligent Equipment Co., Ltd.
Manual revision history：
REV DATE DESCRIPTION REMARK
ANov. 2020 Original issue

APPLICATION
Use the following table to identify the specific serial number for
models included in this manual. Check the model of your machine before
consulting the manual, and then use the correct manual according to the
serial number of the model. See the nameplate on your machine to
identify the model and serial number (SeeDecals/Nameplates
Inspectionof the Operation Manual for details.）
Model
Trade Identification
Serial No.
Metric Imperial
GTTZ10EJ ML10EJ ML340EJ From 0900200110 to present
NOTE:
•Product model is applied in product nameplate for distinction of products of different main
parameters.
•Product trade identification is applied in marketing and machine decals for distinction of products of
different main parameters, and can be classified as metric type and imperial type: The metric type of
trade identification is applicable to machines for countries/regions using metric system or as
specially required by customers; The imperial type of trade identification is applicable to the
machines for countries/regions using imperial system or as specially required by customers.

This Page Intentionally Left Blank

STATEMENTS
Hunan Sinoboom Intelligent Equipment Co., Ltd. (Hereinafter referred to as Sinoboom) will upload the
latest product manual information to the website www. sinoboom. com as soon as possible. However,
due to continuous product improvement, the information in this manual is subject to change without prior
notice.
This manual covers the basic parts information of one or more products. Therefore, please use this
manual according to your needs. If you find problems in the manual or have suggestions for improve-
ment, feel free to share your feedback with Sinoboom, and we will address these issues as soon as
possible.
Feel free to consult and download the Operation Manual,Maintenance Manual and Parts Manual of the
products you need online at www.sinoboom.com.
Hunan Sinoboom Intelligent Equipment Co., Ltd. retains the right of final interpretation of the manual.

This Page Intentionally Left Blank

GTTZ10EJ Operation Manual i© Nov. 2020
TABLE OF CONTENTS
Introduction ............................. iii
1 Machine Specifications ........ 1-1
2 Machine Components .......... 2-1
3 Safety............................... 3-1
Safety Definitions . . . . . . . . .. . . . . . . . . . . . 3-1
Reporting Accidents. . . . . . . . . . . . . . . . . . . 3-1
Electrocution Hazards. . . . . . . . . . . . . . . . . 3-1
Tipping Hazards and Rated Load . . . . . 3-2
Work Environment Hazards . . . . . .. . . . . 3-4
Unsafe Operation Hazards. . . . . . . . . . . . 3-5
FallHazards...........................3-6
Collision Hazards . . . . . . . . . . . . . . . . . . . . . 3-7
Crush Hazards . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Explosion and Fire Hazards. . . . . . . . . . . 3-8
Damaged Machine Hazards . . . . . . . . . . 3-8
Bodily Injury Hazards . . . . . . . . . . . . . . . . . 3-9
Battery Hazards . . . . . . . . . . . . . . . . . .. . . . . 3-9
Welding and Polishing Requirements3-10
Lockout after Each Use . . . . . . . . . . . . . .3-10
4 Jobsite Inspection............... 4-1
5 Pre-operation Inspection ...... 5-1
Tips for Conducting a Pre-operation
Inspection.............................5-1
Conducting a Pre-operation
Inspection.............................5-2
Inspecting Parts . . . . . . . . . . . . . . . . . .. . . . . 5-2
Inspecting Entire Machine . . . . . . . . . . . . 5-2
Inspecting Hydraulic Oil Level. . . . . . . . . 5-2
Inspecting the Battery level . . . . . . . . . . . 5-3
6 Pre-operation Function Test .. 6-1
Preparing for a Pre-operation Func-
tionTest ...............................6-1
Ground Controls . . . . . . . . . . . . . . . . . . . . . . 6-1
Platform Controls . . . . . . . . . . . . . . . . . . . . . 6-4
Testing the Drive Speed. . . . . . . . . . . . . . . 6-8
Testing the Emergency Lowering . . . . . 6-8
Mast emergency lowering . . . . . . . . . . 6-8
Jib boom emergency lowering . . . . . . 6-8
Testing the Pothole Protection . . . . . . . . 6-9
Testing the Tilt Protection . . . . . . . . . . . . . 6-9
Testing the Weighing System . . . .. . . .6-10
7 Operating the machine ......... 7-1
Stability................................7-1
Emergency Stop . . . . . . . . . . . . . . . . . . . . . . 7-3
Emergency Operating. . . . . . . . . . . . . . . . . 7-4
Emergency Control . . . . . . . . . . . . . . . . . . . 7-4
Emergency Towing/Dragging . . . . . . . . . 7-5
Charging the Battery . . . . . . . . . . . . . . . . . . 7-6
Driving on a Slope. . . . . . . . . . . . . . . . . . . . . 7-7
8 Transporting and Lifting the
Machine........................... 8-1
Lifting the Machine with a Crane . . . . . . 8-2
Transporting the Machine . . . . . . . . . . . . . 8-3
9 Maintenance ...................... 9-1
Maintenance Schedule. . . . . . . . . . . . . . . . 9-1
Conducting a Pre-delivery Inspection . 9-4
Maintenance Inspection Report . . . . . . . 9-5
10 Decals/Nameplates
Inspection ....................... 10-1
Decals/Nameplates(GB). . . . . . . . . . .10-2
Decals/Nameplates(CE-Metric) . . .10-5
Decals/Nameplates(CE-Imperial) .10-8
Decals/Nameplates(ANSI). . . . . . . .10-11
Appendix 1: Symbols and
Description.......................A-1

© Nov. 2020 ii GTTZ10EJ Operation Manual
Appendix 2: Prepare the Work
Record Before Delivery ....... A-3
Appendix 3: Maintenance
Inspection Report .............. A-5

GTTZ10EJ Operation Manual iii © Nov. 2020
INTRODUCTION
Thank you for choosing and using the machinery of
Hunan Sinoboom Intelligent Equipment Co., Ltd. Al-
ways read, understand and become familiar with the
operation requirements of the machine and its associ-
ated safety procedures before operating, maintaining
and repairing the machine. Operating the machine with-
out becoming familiar with its specific operation require-
ments and safety procedures poses serious risks.
Operators who follow safety rules and operate the ma-
chine carefully and effectively will prevent personal in-
jury, property loss and accidents.
Use this machine only to transport tools to work loca-
tions and for performing tasks on the work platform. Op-
erators must be competent and must obtain training to
carefully use the machine and follow safety procedures.
Only trained and authorized personnel may operate the
machine.
This manual guides the operator in operating and using
the machine. The operator is responsible for reading,
understanding and implementing the operation and
safety procedures in this manual and for following the
manufacturer’s instructions before beginning any work.
Read, understand and follow all safety rules and oper-
ating instructions. The operator must also consider the
machine’s uses and limitations and the conditions at
the jobsite before using this machine. Strictly following
all safety requirements in this manual is critical.
Consider this manual a part of the machine, along with
Maintenance Manual and Parts Manual, and always
keep the manuals with the machine. The owner or ad-
ministrator of the machine shall offer all manuals and
other necessary information provided by the machine
manufacturer regarding the daily inspection and main-
tenance to each of the renters. If the machine is sold,
the owner or administrator must pass along the man-
uals and other necessary information to the purchaser.
The owner or administrator of the machine shall also
provide the manufacturer’s maintenance information to
the person responsible for maintaining the machine.
If you have any questions, contact Hunan Sinoboom In-
telligent Equipment Co., Ltd..

© Nov. 2020 iv GTTZ10EJ Operation Manual
This Page Intentionally Left Blank

GTTZ10EJ Operation Manual 1-1 © Nov. 2020
1MACHINE SPECIFICATIONS
Table 1-1 GTTZ10EJ Specifications
MEASURE ML10EJ (METRIC) ML340EJ (IMPERIAL)
DIMENSIONAL PARAMETERS
Max platform height 8.3 m 27ft 3in
Max working height 10.3 m 33ft 9.5in
Max horizontal reach 3.3 m 10ft 10in
Overall length(stowed) 2.97 m 9ft 9in
Overall width(stowed) 0.99 m 3ft 3in
Overall height (stowed) 1.99 m 6ft 6in
Wheelbase 1.2 m 3ft 11in
Axle track 0.81 m 2ft 8in
Ground clearance (pothole guard
stowed) 0.06 m 2.36in
Ground clearance (pothole guard
deployed) 0.02 m 0.79in
Tire size (diameter×width / type) 406×127mm / solid 16×5in / solid
Platform dimension (L×W×H) 0.99m×0.7m×1.1m 39×27.5×43in
PERFORMANCE PARAMETERS
Platform rated capacity 200 kg 440 lb
Platform max occupancy (indoor
use) 2 persons
Platform max occupancy (outdoor
use) 1 person
Drive speed (stowed) 0～4 km / h 0～2.5 mph
Drive speed (raised) 0～0.6 km / h 0～0.37 mph
Platform lift time (no load) 32～36 s
Platform lower time (no load) 32～37 s
Gradeability 25%
Max allowable inclination 3° (front-to-back) / 3° (side-to-side)
Turning radius (inside) 0 m 0 ft
Turning radius (outside) 1.55 m 5ft 1in
Turntable tailswing 0 m 0 ft
Turntable slewing angle / continuity 345° / incontinuous

© Nov. 2020 1-2 GTTZ10EJ Operation Manual
MACHINE SPECIFICATIONS
Table 1-1 GTTZ10EJ Specifications (continued)
MEASURE ML10EJ (METRIC) ML340EJ (IMPERIAL)
Drive mode (drive×steer) 2WD×2WS
Max allowable side force (indoor /
outdoor) 400N (indoor) / 200N (outdoor) 90N (indoor) / 45N (outdoor)
Max operating noise level 72 dB
POWER PARAMETERS
Hydraulic tank capacity 8 L 1.8 gal (imperial) / 2.1 gal (US)
Hydraulic system capacity (including
hydraulic tank) 13 L 2.9 gal (imperial) / 3.4 gal (US)
Hydraulic system pressure 15 MPa 2175 psi
Battery (number×voltage, capacity) 4×6V, 240Ah
System voltage 24VDC
Control voltage 24VDC
FLOOR LOADING INFORMATION
Max tire load 1200 kg 2646 lb
Pressure against ground 1180 KPa 171 Psi
ENVIRONMENT REQUIREMENT
Max allowable wind speed (indoor/
outdoor) 0 m / s (indoor) / 12.5 m / s (outdoor) 0 mph (indoor) / 28 mph (outdoor)
Max allowable altitude 1000 m 3281 ft
Allowable ambient temperature
(lead-acid battery) -10℃～40℃14℉～104℉
Allowable ambient temperature (-
lithium battery) -20℃～40℃-4℉～104℉
Max allowable RH 90%
Storage environment
Stored at -20℃to 50℃(-4℉to 122℉) in a well-ventilated environment with
90% relative humidity (20℃[68℉]), and away from rain, sun, corrosive
gas,inflammables and explosives.
WEIGHT
Gross weight (no load) 2678 kg 5904 lb
Note：
a) The working height adds 2m(6ft7in) of human height to platform height.
b) In different areas, hydraulic oil, engine oil, coolant, fuel and lubrication should be added in accordance with the
environmental temperature.
c) In cold weather, auxiliary devices are needed to start the machine.

MACHINE SPECIFICATIONS
GTTZ10EJ Operation Manual 1-3 © Nov. 2020
Chart of motion
Figure 1-1 Chart of motion

© Nov. 2020 1-4 GTTZ10EJ Operation Manual
This Page Intentionally Left Blank
MACHINE SPECIFICATIONS

GTTZ10EJ Operation Manual 2-1 © Nov. 2020
2MACHINE COMPONENTS
Figure 2-1
18 19 2017
12
14
13
8
7
6
5
10
4
23
15
16
1
11
9
2423
22
21
25

© Nov. 2020 2-2 GTTZ10EJ Operation Manual
MACHINE COMPONENTS
Table 2-1
1. Platform controls 10. Extending unit 19. Drive reducer
2. Work platform 11. Ground controls 20. Drive rear wheel
3. Manual storage container (option) 12. Counterweight 21. Battery
4. Jib boom 13. Turntable cover, LH 22. Power unit
5. Mast section 4 14. Turntable cover, RH 23. Slewing unit
6. Mast section 3 15. Power disconnect switch 24. Steer cylinder
7. Mast section 2 16. Charger plug cable 25. Chassis
8. Mast section 1 17. Steering front wheel
9. Flashing beacon 18. Pothole guard plate
Machine positions
Operating/raised position：
The machine comes in operating/raised position when
the mast raises so that the lower limit switch becomes
disengaged.
Stowed position：
The machine comes in stowed position when the mast
is fully lowered.

GTTZ10EJ Operation Manual 3-1 © Nov. 2020
3SAFETY
Read, understand and comply with the safety rules and
regulations of your workplace and your government.
Before using the machine, obtain proper training on
safe machine operation and make sure you can safely
control and operate the machine.
Understand that as the operator you have the responsi-
bility and right to shut down the machine in case of fail-
ure with the machine or other emergency at your
workplace.
NOTICE
People suffering from heart disease, hypertension,
epilepsy and other diseases and people who fear
heights must never operate or use this machine. Al-
so, people who have alcohol or drugs in their system,
or experience excessive fatigue or depression, are
prohibited from operating or using this machine.
SAFETY DEFINITIONS
This safety alert symbol appears with
most safety statements. It means atten-
tion, become alert, your safety is in-
volved! Please read and abide by the
message that follows the safety alert
symbol.
Indicates a hazardous situation that, if not
avoided, will result in death or serious injury.
Indicates a hazardous situation that, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation that, if not
avoided, could result in minor or moderate injury.
NOTICE
Indicates a situation that can cause damage to the
engine, personal property and/or the environment, or
cause the equipment to operate improperly.
NOTE: Indicates a procedure, practice or condition that
should be followed in order for the engine or component
to function in the manner intended.
REPORTING ACCIDENTS
In case of any accident involving the machinery of , noti-
fy Immediately, even if no personal injury or property
damage occurs during the accident. Contact by tele-
phone and provide all necessary details. Failure to noti-
fy the manufacturer within 48 hours of the incident
involving the machinery of may void the product's
warranty.
NOTICE
Thoroughly inspect the machine and all its functions
after any accident, being sure to test first from the
ground controller and then from the platform control-
ler. Ensure the machine's lifting height does not ex-
ceed 3 m(9.8 ft) until all damage has been repaired
and all controllers operate properly.
ELECTROCUTION
HAZARDS
NOTE: This machine is not insulated and does not
have an electric shock protection function.
All operators and managers shall comply with national
or local regulations regarding the minimum safe
distance of live conductors above the ground. In the
absence of such requirements, operators and
managers should follow the minimum safety distance
requirements in Table 3-1 , page 3-2.

© Nov. 2020 3-2 GTTZ10EJ Operation Manual
SAFETY
ELECTRICAL SHOCK HAZARDS
• Always maintain a safe distance
from power lines and electrical
equipment in accordance with
applicable government
regulations and see Table 3-1 ,
page 3-2.
• Consider platform and boom
movement, wire swinging or
drooping, beware of strong winds
or gusts, and do not operate the
machine when there is lightning
or heavy rain.
• If the machine comes into contact
with live wires, keep away from
the machine. Personnel on the
ground or on the platform must
not touch or operate the machine
until the power is switched off.
• Do not use the machine as a
ground wire during welding and
polishing operations.
Table 3-1
Voltage
(Phase to Phase, kV)
Minimum safe distance
(m/ft)
0-50 3.05 (10)
50-200 4.60 (15)
200-350 6.10 (20)
350 -500 7.62 (25)
500 -750 10.67 (35)
750 -1000 13.725 (45)
TIPPING HAZARDS AND
RATED LOAD
Maximum rated load bearing capacity of the
platform:200kg (440lb)
TIPPING HAZARDS
• Personnel, equipment and
materials on the platform must
not exceed the maximum load
capacity.
• Only raise or extend the mast
when the machine is on solid,
level ground.
• Select only the low speed when
driving the machine on a slope.
• Do not use the tilt alarm as a level
indicator. The tilt alarm on the
platform will sound only if the
machine is heavily tilted.
• Carefully lower the platform and
move the machine to a firm level
surface. Do not rotate the
turntable while the lowering the
mast. Any unauthorized
modification of the level or limit
switches is strictly forbidden.
• Do not drive faster than 0.6 km/h
(0.37 mph) when the platform is
raised.
• When the platform is raised, the
machine cannot travel on uneven
terrain, unstable surfaces or in
other dangerous conditions.
• Do not operate the machine
during strong winds or gusts, and
do not increase the surface area
of the platform or load. Increasing
the area exposed to the wind will
reduce the stability of the
machine.
• When the machine is on rough
ground, with gravel or other
uneven surfaces, or near holes
and steep slopes, maintain a
minimum distance of 0.6m (2ft)
and reduce the speed.
• When on the platform do not push
and pull objects outside of it. The
maximum lateral force allowed
is:400 N (90 lbf).
• Tow the machine only from the
tiedown/lifting points on the
chassis.
• Never use the mast or platorm to
stablize or support any objects
outside of the machine.