SIRETTA SNYPER-LTE Spectrum User manual

SNYPER-LTE Spectrum
Cellular Signal and Network
Analyser with liveSCAN
Quick Start Guide
Rev 1.1

2
Contents Page
Case Contents 3
Preparing the SNYPER-LTE Spectrum
(Non liveSCAN Mode) 4
Main Menu 5
Performing an LTE Survey 6
View LTE Survey Results 7
Save LTE Survey Results 8
Performing a GSM/UMTS Survery 9
View GSM/UMTS Survey Results 10
Save GSM/UMTS Survey Results 11
Viewing Saved Survey Results 12
Downloading Saved Data 13
Performing a liveSCAN 14
Performing an LTE liveSCAN 14
Performing a GSM/UMTS livescan 15
Powering off the SNYPER-LTE Spectrum 15

3
Case Contents
Unpack the case contents to begin using your SNYPER-LTE Spectrum signal strength
tester.
1. SNYPER-LTE Spectrum signal and network analyser
2. Multi region power supply
3. Blue antenna - General purpose LTE(4G), UMTS(3G) & GPRS(2G) coverage
4. Silver antenna - For LTE 2600MHz only
5. liveSCAN antenna
6. Cable
7. USB cable
8. In car charger
9. Hard carrying case
Quick start guide
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
10
8
7
6
Figure 1. SNYPER-LTE Spectrum case contents
9

4
Preparing the SNYPER-LTE Spectrum
(Non liveSCAN Mode)
SIM
1. Select and attach the antenna required for the network you will be surveying
(Blue antenna - 2/3/4G / Silver antenna - 2600MHz). Screw the antenna onto the
SNYPER-LTE Spectrum by turning clockwise until the antenna is rmly connected.
2. This device requires an active 4G enabled SIM when performing surveys on all
LTE, UMTS and GSM networks. Insert SIM card as shown below.
3. The SNYPER-LTE Spectrum needs to be charged using the mains adaptor for 6 -
8 hours before initial use.
4. Power on the SNYPER-LTE Spectrum by pressing and holding the power button.
See gure 3 for power on screen.
Figure 3. Power on screen
1
2
3
4
1
2
3
4
Figure 2. Preparing SNYPER-LTE Spectrum

5
Main Menu
The main menu will be displayed when the SNYPER-LTE Spectrum has successfully
powered on. The main menu has 7 menus (as shown below in gure 4), these can be
selected using the UP/DOWN buttons. Once the chosen menu is highlighted, click the
OK button. Press the BACK button to return to the main menu.
Figure 4. ‘Main Menu’ screen
Saved Results: Reviews previously saved survey.
Survey: Used to perform a new survey.
Setup: Basic setups of the SNYPER-LTE Spectrum.
(Brightness / Auto Off / Delay / CRG Rate / Text / HTML)
Options: User options for the SNYPER-LTE Spectrum.
(Standard / Factory Reset)
About: Displays information about the SNYPER-LTE Spectrum.
(Version / Settings)
PC Connect: Download of data to PC.
Power Off: Powers off the SNYPER-LTE Spectrum.

6
Performing an LTE Survey
1. Use the menu buttons to select ‘Survey’, click the OK button.
2. Select ‘LTE Survey’, click the OK button.
3. Survey will begin performing
1 2 3
1
2
3
Figure 5. Select survey Figure 6. Selecting
LTE survey
Figure 7. Performing
survey

7
View LTE Survey Results
After the LTE survey has nished performing, a summary of all LTE results will be
displayed (as shown in gure 8). Using the menu buttons, select the network results you
wish to view. Press OK (see gure 9 for network results).
Figure 8. ‘Survey Menu’ screen
NOTE: See ‘SNYPER-LTE Spectrum - User Manual’ if you require more information on interpreting
survey results.
Figure 9. LTE results

8
Save LTE Survey Results
1. Press the back button until you return to the ‘LTE Menu’ screen.
2. Select ‘Save’, click the OK button.
3. Results will save.
1
2
3
1 2 3
Figure 10. Saving
results
Figure 11. Selecting
save option
Figure 12. LTE
results being saved

9
Performing a GSM/UMTS Survey
1. Use the menu buttons to select ‘Survey, click the OK button.
2. Select ‘GSM/UMTS’, click the OK button.
3. Survey will begin performing
1 2 3
1
2
3
Figure 13. Select survey Figure 14. Selecting
GSM/UMTS survey
Figure 15. GSM\UMTS
results being saved

10
View GSM/UMTS Survey Results
New Survey: Performs a new network survey.
Save: Saves the results of the performed survey.
GSM & UMTS: Displays GSM & UMTS survey results.
UMTS: Displays UMTS survey results (see gure 17).
GSM: Displays GSM survey results (see gure 18).
Summary: Displays an overview of all networks and number
of base stations for given signal strength (see gure 19).
After the survey has nished performing, the ‘Survey Menu’ will be displayed (as shown
in gure 16). Use the menu buttons to select the results you wish to view. Press OK.
Figure 16. ‘Survey Menu’ screen
Figure 17. UMTS results
NOTE: See ‘SNYPER-LTE Spectrum - User Manual’ if you require more information on interpreting
survey results.
Figure 18. GSM results Figure 19. Summary

11
Save GSM/UMTS Survey Results
1. Press the back button until you return to the ‘Survey Menu’ screen.
2. Select ‘Save’, click the OK button.
3. Results will save.
1
2
3
1 2 3
GSM & UMTS: Displays GSM & UMTS survey results.
Figure 20. Saving
results
Figure 21. Selecting
save option
Figure 22. GSM/UMTS
results being saved

12
Viewing Saved Results
1. Use the menu buttons to select ‘Saved Results’, click the OK button.
2. Select ‘LTE Survey’ or ‘GSM/UMTS Survey’, click the OK button.
3. Use the menu buttons to select the saved results you wish to view, click ‘View’.
1 2
1
2
Figure 23. Selecting
saved results
Figure 24. Select results
you wish to view
3
3Figure 25. Select saved
results to view

13
Downloading Saved Data
1. Connect supplied USB cable to the SNYPER-LTE Spectrum and PC.
2. From the SNYPER-LTE Spectrum ‘Main Menu’ select ‘PC Connect’ and ‘Enable’.
From the PC select ‘Open Folder to View Files’ and open saved les (copy les to
hard drive as required).
1
2
2
1
USB cable
HTML graphical results display in your browser.
Figure 26. Connecting USB cable
Figure 27. Downloading resutlts

14
Performing a liveSCAN
The liveSCAN operation with the SNYPER-LTE Spectrum has two uses:
1: Locating the direction of a specic cell using a directional antenna
2: Locating the presence of strongest available signal in a survey result
1. Perform a survey as shown in ‘Performing an LTE Survey’ (page 6). From the LTE
summary screen, select the desired network you would like to liveSCAN, press
the OK button. Press OK again to begin liveSCAN.
1
Performing an LTE liveSCAN
1. Connect the supplied liveSCAN antenna to the SNYPER-LTE Spectrum.
1
Figure 28. Connecting liveSCAN antenna
Figure 29. LTE summary Figure 30. Begin liveSCAN Figure 31. liveSCAN in function
1

15
Powering off the SNYPER-LTE Spectrum
After use, remember to power off the SNYPER-LTE Spectrum. This can be done by:
»Selecting the ‘Power Off’ option from the main menu. The SNYPER-LTE
Spectrum will display a power off message.
»Press and hold the ON/OFF button on the SNYPER-LTE Spectrum for >2
seconds. The SNYPER-LTE Spectrum will display a power off message.
To stop performing a liveSCAN, press and hold the BACK button to return to
the previous menu.
1. Perform a survey as as shown in ‘Performing a GSM/UMTS Survey’ (page 9).
From the ‘Survey Menu’ use the menu buttons to select whether you want to
view GSM or UMTS results, press the OK button. Use the LEFT/RIGHT buttons
to select the desired network you wish to liveSCAN, press the OK button to begin
liveSCAN.
1
Performing a GSM/UMTS liveSCAN
Figure 32. Survey menu Figure 33. Begin liveSCAN Figure 34. liveSCAN in function

Basingstoke Road
Spencers Wood
Reading
Berkshire
RG7 1PW
United Kingdom
Rev 1.1
sales
fax
accounts
email
Company No. 08405712
VAT Registration No. GB163 04 0349
A member of the Olancha Group Ltd
[phone]
[phone]
[phone]
[email protected]
www.siretta.co.uk
Further Information
Full user guide for the SNYPER-LTE Spectrum can be downloaded from the Siretta website.
www.siretta.co.uk/snyper-lte