SKF Lincoln P205-M075 2K7-000 EEX Series User manual

951-181-014-EN
Version 16
2021/07/12
EN
Operating Instructions
following ATEX directive 2014/34/EU
Lubrication pump P205EEX

- 2 -
951-181-014-EN
Version 16
EN
Jürgen Kreutzkämper
Manager R&D Germany
Stefan Schürmann
Manager PD Germany South
EU Declaration of conformity following ATEX directive 2014/34/EU, annex X
The manufacturer, SKF Lubrication Systems Germany GmbH,Walldorf Facilities, Heinrich-Hertz-Str. 2-8, DE - 69190 Walldorf hereby declares under sole
responsibility that the electrical equipment
Designation: Electrically driven pump to supply lubricant within a centralized lubrication system
Types: P205xxxEEX
Part numbers: 655-xxxxx-x | 6550-xxxxxxxx
Year of construction: See type identification plate
complies with the following basic safety and health requirements of ATEX directive 2014/34/EU and the safety and health requirements of machinery directive
2006/42/EC at the time when first being launched in the market.
1.1.2 · 1.1.3 · 1.3.2 · 1.3.4 · 1.5.6· 1.5.8 · 1.5.9 · 1.6.1 · 1.7.1 · 1.7.3 · 1.7.4
The special technical documents were prepared following:
○ATEX directive 2014/34/EU annex VIII (2) and stored at the named institute (CE0123).
○Machinery directive 2006/42/EC, annexVII, part B was prepared.
We undertake to send this in electronic form to the respective authorities upon justifiable request.The person empowered to assemble the technical docu-
mentation on behalf of the manufacturer is the head of standardization, See manufacturer's address.
Furthermore, the following directives and harmonized standards were applied in the respective applicable areas:
Directives
2011/65/EU RoHS II
2014/30/EU Electromagnetic compatibility
Standards
EN ISO 12100:2010 EN 1127-1:2011 EN 61000-6-2:2005 EN 50581:2012
EN 809:1998+A1:2009/AC2010 EN ISO 80079-36:2016 EN 61000-6-4:2007/A1:2011
EN 60204-1:2006/AC:2010 EN ISO 80079-37:2016 EN 60947-5-2:2007/A1:2012
The machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the previsions of
ATEX directive 2014/34/EU of machinery directive 2006/42/EC and any other applicable directives.
Walldorf, 2020/06/15

- 3 -
951-181-014-EN
Version 16
EN
Legal notice
Training courses
In order to provide a maximum of safety and
economic viability, SKF carries out detailed
training courses. It is recommended that the
training courses are attended. For more in-
formation please contact the respective SKF
Service address.
Copyright
© Copyright SKF
All rights reserved.
Warranty
The instructions do not contain any informa-
tion on the warranty.This can be found in
our general terms and conditions.
Disclaimer
The manufacturer shall not be held respon-
sible for damages caused by:
○non appropriate use
faulty assembly, operation, setting, main-
tenance, repair, negligence or accidents
○Use of inappropriate lubricants
○Improper or late response to
malfunctions
○Unauthorized modifications of the
product
○the use of non-original
SKF spare parts
Liability for loss or damage resulting from
the use of our products is limited to the
maximum purchase price. Liability for
consequential damages of whatever kind is
excluded.
Legal notice
Manufacturer
SKF Lubrication Systems Germany GmbH
www.skf.com/lubrication
Manufacturer's facilities
Head Office
Walldorf Facilities
Heinrich-Hertz-Str. 2-8
69190 Walldorf
Germany
Phone [phone]
Fax: [phone]
Berlin Facilities
Motzener Straße 35/37
12277 Berlin
Germany
Phone [phone]
Fax [phone]
www.skf.com/lubrication

- 4 -
951-181-014-EN
Version 16
EN Table of contents
Table of contents
EU Declaration of conformity following ATEX directive 2014/34/EU......... 2
Legal notice ................................................................................................ 3
Explanation of symbols, signs and abbreviations ...................................... 7
1. Safety instructions........................................................................ 9
1.1 General safety instructions....................................................................9
1.2 General behaviour when handling the product...................................9
1.3 Intended use..........................................................................................10
1.4 Foreseeable misuse..............................................................................10
1.5 Painting of plastic parts........................................................................10
1.6 Modifications of the product................................................................11
1.7 Prohibition of certain activities............................................................11
1.8 Inspections prior to delivery ................................................................11
1.9 Other applicable documents................................................................11
1.10 Markings on the product......................................................................11
1.11 Notes related to the type identification plate.....................................12
1.12 Notes related to the CE marking.........................................................12
1.13 Persons authorized to operate the pump ..........................................13
1.13.1 Operator.................................................................................................13
1.13.2 Specialist in mechanics ........................................................................13
1.13.3 Specialist in electrics ............................................................................13
1.13.4 Specialist for maintenance and repairs in potentially explosive atmospheres..13
1.14 Briefing of external technicians...........................................................13
1.15 Provision of personal protective equipment......................................13
1.16 Operation...............................................................................................14
1.17 Emergency stopping.............................................................................14
1.18 Transport, installation, maintenance, malfunctions, repair,
shutdown, disposal...............................................................................14
1.19 Initial commissioning, daily start-up ..................................................15
1.20 Cleaning .................................................................................................16
1.21 Safety-related protective and emergency devices must..................16
1.22 Special safety instructions regarding explosion protection .............17
1.23 Expiry of the ATEX approval.................................................................19
1.24 Operation in explosion-protected areas.............................................19
1.25 Explosion protection marking..............................................................19
1.26 Residual risks ........................................................................................20
1.27 Residual risks ATEX ..............................................................................21
2. Lubricants................................................................................... 23
2.1 General information .............................................................................23
2.2 Selection of lubricants..........................................................................23
2.3 Material compatibility...........................................................................23
2.4 Temperature characteristics................................................................23
2.5 Ageing of lubricants..............................................................................24
3. Overview, functional description ................................................ 25
4. Technical data............................................................................. 28
4.1 Mechanical data....................................................................................28
4.2 Electrics:.................................................................................................29
4.3 Nominal output volumes ....................................................................30
4.3.1 Influencing variables on the actual output volume...........................30
4.3.2 Output diagrams of typical NLGI 2 lubricants....................................30
4.4 Tightening torques ...............................................................................31
4.4.1 Tightening torques for CEMP motor...................................................31

- 5 -
951-181-014-EN
Version 16
EN
Table of contents
4.5 Overview of pump versions.................................................................32
4.6 Technical data of motor variants.........................................................34
4.7 Reservoir versions ................................................................................42
4.8 Capacitive sensors ................................................................................43
4.9 Contact rod ............................................................................................45
5. Delivery, returns, and storage.................................................... 46
5.1 Delivery..................................................................................................46
5.2 Returns ..................................................................................................46
5.3 Storage...................................................................................................46
5.3.1 Corrosion protection.............................................................................46
5.3.2 Special storage conditions of the motor.............................................46
5.4 Special storage conditions for parts primed with lubricant .............47
5.4.1 Storage period of up to 6 months.......................................................47
5.4.2 Storage period from 6 to 18 months..................................................47
5.4.3 Storage period exceeding 18 months ................................................47
6. Installation.................................................................................. 48
6.1 General information .............................................................................48
6.2 Place of installation...............................................................................48
6.3 Mechanical connection.........................................................................49
6.3.1 Minimum assembly dimensions .........................................................49
6.3.2 Installation bores ..................................................................................50
6.4 Electrical connection of SEW and CEMP motors ..............................51
6.5 Protective conductor connection of SEW motor ...............................52
6.6 Electrical connection of the low-level indication...............................52
6.7 Electrical connection of ELNOR motor...............................................53
6.8 Adjustment of the KR pump elements...............................................55
6.9 Lubrication line connection..................................................................56
6.10 Filling with lubricant.............................................................................57
6.10.1 Filling via the reservoir lid....................................................................57
6.10.2 Filling via filling port..............................................................................57
6.10.3 Inadvertent filling with incorrect lubricant.........................................58
7. Initial start-up ............................................................................ 59
7.1 Inspections prior to initial start-up.....................................................59
7.2 Inspections during initial start-up ......................................................60
8. Operation.................................................................................... 61
8.1 Activation of the pump.........................................................................61
8.2 Refill lubricant .......................................................................................61
9. Cleaning...................................................................................... 62
9.1 Cleaning agents ....................................................................................62
9.2 Exterior cleaning...................................................................................62
9.3 Interior cleaning....................................................................................62

- 6 -
951-181-014-EN
Version 16
EN Table of contents
10. Maintenance ............................................................................... 63
10.1 Pump maintenance ..............................................................................64
10.2 Maintenance of gear unit ...................................................................65
10.3 Cleaning of capacitive sensors ............................................................65
10.4 Motor maintenance ..............................................................................66
10.5 Measurement of the insulation resistance.........................................68
11. Troubleshooting.......................................................................... 69
12. Repairs........................................................................................ 75
12.1 Replacement of capacitive sensor.......................................................76
13. Shutdown and disposal .............................................................. 79
13.1 Temporary shutdown...........................................................................79
13.2 Final shutdown and disassembly........................................................79
13.3 Disposal..................................................................................................79
14. Spare parts................................................................................. 80
14.1 Capacitive sensor M18 x 1...................................................................80
14.2 Filling level sensor LBFS......................................................................80
14.3 SEW motor ............................................................................................81
14.4 GasketAbil Ø 40 x 70 x 0.5..................................................................81
14.5 Cemp motor...........................................................................................82
14.6 ELNOR motor........................................................................................82
14.7 GasketAbil Ø 60 x 90 x 0.5..................................................................82
Annexes purchase parts........................................................................... 83
Declaration of conformity of gear make Rehfuss ..................................... 83
Declaration of conformity of EDR motor make SEW................................ 84
Declaration of conformity of DFR motor make SEW................................ 85
Declaration of conformity of BA AP80 motor make ELNOR..................... 86
Declaration of conformity of motor make CEMP...................................... 87
Declaration of conformity of motor make CEMP...................................... 88
Declaration of conformity of motor make CEMP...................................... 89
Declaration of conformity of motor make CEMP...................................... 90
Declaration of conformity of terminal box make Bartec .......................... 91
Declaration of conformity of capacitive sensor make Turck..................... 92
Declaration of conformity of filling-level sensor make Bartec................. 93

- 7 -
951-181-014-EN
Version 16
EN
Explanation of symbols, signs and abbreviations
Explanation of symbols, signs and abbreviations
General warning Dangerous electrical voltage Risk of falling Hot surfaces
Unintentional intake Crushing hazard Pressure injection Suspended load
Electrostatically sensitive
components Risk of explosion Explosion-protected component
Wear personal protective
equipment (goggles) Wear personal protective equipment (face shield) Wear personal protective equipment (gloves) Wear personal protective equipment (protective clothes)
Wear personal protective
equipment (safety shoes) Disconnect product from mains General obligation
Keep unauthorized persons
away Protective earth Safety extra-low voltage (SELV) Safe galvanic isolation (SELV)
CE marking Disposal, recycling Disposal of waste electrical
and electronic equipment
Warning level Consequence Probability Symbol Meaning
DANGER Death, serious
injury imminent Chronological guidelines
WARNING Death, serious
injury possible Lists
CAUTION Minor
injury possible Refers to other facts, causes, or consequences
NOTICE Property damage possible
The following abbreviations may be used within these instructions. Symbols within safety notes mark the kind and source of the hazard.

- 8 -
951-181-014-EN
Version 16
EN Explanation of symbols, signs and abbreviations
Abbreviations and conversion factors
re. regarding °C degrees Celsius °F degrees Fahrenheit
approx. approximately K Kelvin Oz. Ounce
i.e. that is N Newton fl. oz. fluid ounce
etc. et cetera h hour in. inch
poss. possibly s second psi pounds per square inch
if appl. if applicable d day sq.in. square inch
a.a.r. as a rule Nm Newtonmeter cu. in. cubic inch
incl. including ml millilitre mph miles per hour
min. minimum ml/d millilitre per day rpm revolutions per minute
max. maximum cc cubic centimetre gal. gallon
min. minute mm millimetre lb. pound
etc. et cetera l litre hp horse power
e.g. for example dB (A) sound pressure level kp kilopond
kW kilowatt > greater than fpsec feet per second
U Voltage < less than conversion factors
R resistance ± plus/minus Length 1 mm = 0.03937 in.
I current Ø diametre Area 1 cm = 0.155 sq.in
V volt kg kilogram Volume 1 ml = 0.0352 fl.oz.
Wwatt rh relative humidity 1l = 2.11416 pints (US)
AC alternating current ≈ about Mass 1 kg = 2.205 lbs
DC direct current = equal to 1 g = 0.03527 oz.
A ampere % per cent Density 1 kg/cc = 8.3454 lb./gal(US)
Ah ampere hour ‰ per mille 1 kg/cc = 0.03613lb./cu.in.
Hz frequency [Hertz] ≥ greater than Force 1 N = 0.10197 kp
nc normally closed ≤ less than Pressure 1 bar = 14.5 psi
no normally open contact mm2square millimetre Temperature °C = (°F-32) x 5/9
OR logical OR rpm revolutions per minute Output 1kW = 1.34109 hp
&logical AND Acceleration 1 m/s = 3.28084 ft./s
N/A Not applicable Speed 1m/s = 3.28084 fpsec.
1m/s = 2.23694 mph

1
- 9 -
951-181-014-EN
Version 16
EN
1. Safety instructions
1. Safety instructions
1.1 General safety instructions
○The owner must ensure that safety infor-
mation has been read by any persons en-
trusted with works on the product or by
those persons who supervise or instruct
the before-mentioned group of persons.
In addition, the owner must also ensure
that the relevant personnel are fully fa-
miliar with and have understood the con-
tents of the Instructions. It is prohibited to
commission or operate the product prior
to reading the Instructions.
○These Instructions must be kept for fur-
ther use.
○The described products were manufac-
tured according to the state of the art.
Risks may, however, arise from a usage
not according to the intended purpose
and may result in harm to persons or
damage to material assets.
○Any malfunctions which may affect safety
must be remedied immediately. In addi-
tion to these Instructions, general statu-
tory regulations for accident prevention
and environmental protection must be
observed.
1.2 General behaviour when handling the
product
○The product may be used only in aware-
ness of the potential dangers, in proper
technical condition, and according to the
information in these instructions.
○Familiarize yourself with the functions
and operation of the product.The speci-
fied assembly and operating steps and
their sequences must be observed.
○Any unclear points regarding proper
condition or correct assembly/ operation
must be clarified. Operation is prohibited
until issues have been clarified.
○
Unauthorized persons must be kept away.
○Precautionary operational measures and
instructions for the respective work must
be observed.
○Responsibilities for different activities
must be clearly defined and observed.
Uncertainty seriously endangers safety.
○Remedy occurring faults in the frame of
responsibilities. Immediately inform your
superior in the case of faults beyond your
competence.
○Wear personal protective equipment.
○Never use parts of the centralized lu-
brication system or of the machine as
standing or climbing aids.

- 10 -
951-181-014-EN
Version 16
EN 1. Safety instructions
1.3 Intended use
Supply of lubricants within a centralized
lubrication system following the specifica-
tions, technical data and limits stated in
these Instructions:
Usage is allowed exclusively for professional
users in the frame of commercial and eco-
nomic activities.
1.4 Foreseeable misuse
Any usage differing from the one stated in
these Instructions is strictly prohibited. It is
expressly forbidden to be used:
○outside the indicated temperature range
○with non-specified means of operation
○with contaminated lubricants or lubri-
cants with air inclusions
○with lubricants the temperature of which
exceeds the maximum admissible ambi-
ent temperature
○without adequate pressure control valve
○in areas with aggressive or corrosive ma-
terials (e.g. high ozone pollution). These
may affect seals and painting.
○in areas with harmful radiation (e. g. ion-
ising radiation)
○to supply, transport, or store hazardous
substances and mixtures in accordance
with annex I part 2-5 of the CLP regula-
tion (EG 1272/2008) and marked with
GHS01-GHS06 and GHS08 hazard
pictograms.
○to feed, forward, or store gases, liquefied
gases, dissolved gases, vapours, or fluids
whose vapour pressure exceeds normal
atmospheric pressure (1013mbar) by
more than 0.5bar at the maximum per-
missible operating temperature.
○to feed, forward, or store lubricants con-
taining volatile solvents
○in explosive gas and vapour atmos-
pheres, the ignition temperature of which
is smaller than 125 % of the maximum
surface temperature
○in explosive dust atmospheres, the mini-
mum ignition and glow temperature of
which is smaller than 150 % of the maxi-
mum surface temperature
○In a different, more critical potentially
explosive atmosphere than stated on
the type identification plate of the pump
used.
○with damaged or lackingATEX painting or
ATEX painting done wrongly later on. The
painting must comply with the standards
valid for ATEX.
1.5 Painting of plastic parts
Painting of any plastic parts or seals of the
described products is expressly prohibited.
Remove or tape plastic parts completely
before painting the superior machine

1
- 11 -
951-181-014-EN
Version 16
EN
1. Safety instructions
1.6 Modifications of the product
Unauthorized conversions or modifica-
tions may result in unforeseeable impacts
on safety. Therefore, any unauthorized
conversions or modifications are expressly
prohibited.
1.7 Prohibition of certain activities
Due to potential sources of faults that may
not be visible or due to legal regulations the
following activities may be carried out only
by manufacturer specialists or persons au-
thorized by the manufacturer:
○Repairs or changes to the drive
○Replacement of or changes on the pis-
tons of the pump elements
1.8 Inspections prior to delivery
The following inspections were carried out
prior to delivery:
○Safety and functional tests
○Electrical inspections following DIN EN
60204-1:2007 / VDE 0113-1:2007.
○In case of explosion-protected products:
Inspections following the requirements of
the ATEX Directive.
1.9 Other applicable documents
In addition to these instructions, the follow-
ing documents must be observed by the
respective target group:
○Operational instructions and approval
rules
○Safety data sheet of the lubricant used
Where appropriate:
○Project planning documents
○Any documents of other components
required to set up the centralized lubrica-
tion system
○Operator's explosion protection
document
○Rehfuss gear:
Instructions for the SM type series
○SEW motor:
Explosion-protected three-phase motors
EDR71 documentation no.: 19402007
○CEMP motor:
ATEX safety instructions (multilingual)
Instructions for use and maintenance
(multilingual)
1.10 Markings on the product
Warning of dangerous electrical
voltage
Warning of hand injuries when
reaching into the reservoir
Rotational direction of the pump
Equipotential bonding
connections

- 12 -
951-181-014-EN
Version 16
EN 1. Safety instructions
1.11 Notes related to the type identifica-
tion plate
The type identification plate states im-
portant characteristics such as type des-
ignation, order number, and regulatory
characteristics.
To ensure that the loss of data due to an
illegible type identification plate is avoided,
the characteristics should be entered in the
Instructions.
Model: _______________________________
P. No.: ________________________________
Series: _______________________________
Year of construction (KW/YY)
________________________
Voltage:_______________________________
Control voltage:________________________
Power:________________________________
_______°C ≤ Ta ≤ _______°C
SKF Lubrication Systems Germany GmbH
Model:
P. No.:
S. No.:
xxx -xxx-xxx-xxx-xxx
xxxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx
Made in Germany
U & P: see motor type identification plate
KW/JJFactory address
-xx °C ≤ Ta ≤ +xx °C
IIxG Ex h IIx Tx Gb
IIxD Ex h IIIx Txxx°C Db
1.12 Notes related to the CE marking
CE marking is effected following the re-
quirements of the applied directives:
○2014/34/EU
Directive relating to equipment and
protective systems for use in explosive
atmospheres (ATEX)
○2014/30/EU
Electromagnetic compatibility
○2011/65/EU
(RoHS II) Directive on the restriction of
the use of certain hazardous substances
in electrical and electronic equipment
Reference on LowVoltage Directive
2014/35/EU
The protective regulations of Low Voltage
Directive 2014/35/EU are fulfilled according
to annex II (1.2.7) of ATEX Directive
2014/34/EU.
Reference on Pressure Equipment Directive
2014/68/EU
Because of its performance data the prod-
uct does not achieve the limit values de-
fined in Article4(1)(a)(ii) and is therefore
excluded from the scope of application of
Pressure Equipment Directive 2014/68/EU
following Article 1(2) (f).

1
- 13 -
951-181-014-EN
Version 16
EN
1. Safety instructions
1.13 Persons authorized to operate the
pump
1.13.1 Operator
A person who is qualified by training, know-
ledge and experience to carry out the func-
tions and activities related to normal opera-
tion. This includes avoiding possible hazards
that may arise during operation.
1.13.2 Specialist in mechanics
Person with appropriate professional edu-
cation, knowledge and experience to detect
and avoid the hazards that may arise during
transport, installation, start-up, operation,
maintenance, repair and disassembly.
1.13.3 Specialist in electrics
Person with appropriate professional edu-
cation, knowledge and experience to detect
and avoid the hazards that may arise from
electricity.
1.13.4 Specialist for maintenance and
repairs in potentially explosive
atmospheres
A person who is qualified by training, know-
ledge and experience to identify and assess
possible risks and hazards during work
on the machine or partial components in
potentially explosive areas and to initiate
suitable measures to prevent such risks.
The specialist has knowledge of the differ-
ent ignition protection types, installation
procedures and zone divisions. He is famil-
iar with the rules and regulations relevant
for his activities and explosion protection, in
particular with ATEX directives 2014/34/EU
and 1999/92/EC.
1.14 Briefing of external technicians
Prior to commencing the activities, external
technicians must be informed by the opera-
tor of the company safety provisions, the
applicable accident prevention regulations
to be maintained, and the functions of the
superordinate machine and its protective
devices.
1.15 Provision of personal protective
equipment
The operator must provide suitable per-
sonal protective equipment for the respec-
tive location of operation and the purpose of
operation. For work in potentially explosive
atmospheres this also includes ESD cloth-
ing and ESD tools.

- 14 -
951-181-014-EN
Version 16
EN 1. Safety instructions
○Dry or cover wet, slippery surfaces
accordingly.
○Cover hot or cold surfaces accordingly.
○Work on electrical components must be
carried out by electrical specialists only.
Observe any waiting periods for dis-
charging, if necessary. Carry out works
on electrical components only while the
system is depressurized and use voltage
isolated tools suitable for electrical works
only.
○Carry out electrical connections only ac-
cording to the information in the valid
wiring diagram and taking the relevant
regulations and the local connection con-
ditions into account.
○Carry out transport using suitable trans-
port and hoisting equipment on suitable
ways only.
○Maintenance and repair work can be
subject to restrictions in low or high tem-
peratures (e.g. changed flow properties of
the lubricant).Therefore, where possible,
try to carry out maintenance and repair
work at room temperature.
○Prior to performing work, the product
and the machine, into which the product
will be integrated, must be depressur-
ized and secured against unauthorized
activation.
○Ensure through suitable measures that
movable or detached parts are immobi-
lized during the work and that no limbs
can be caught in between by inadvertent
movements.
○Assemble the product only outside of the
operating range of moving parts, at an
adequate distance from sources of heat
or cold. Other units of the machine or ve-
hicle must not be damaged or impaired in
their function by the installation.
1.16 Operation
The following must be observed during
commissioning and operation:
○Any information within this manual and
the information within the referenced
documents
○All laws and regulations to be complied
with by the user
1.17 Emergency stopping
In case of an emergency stop the pump sta-
tion by:
○Switching off the superior machine or
system in which the pump station has
been integrated.
○Actuating the emergency stop switch of
the superior machine.
1.18 Transport, installation, maintenance,
malfunctions, repair, shutdown,
disposal
○All relevant persons must be informed
of the activity prior to starting any work.
Observe the precautionary operational
measures and work instructions.

1
- 15 -
951-181-014-EN
Version 16
EN
1. Safety instructions
○No parts of the centralized lubrication
system may be subjected to torsion,
shear, or bending.
○Check all parts prior to their usage for
contamination and clean, if necessary.
○Lubricant lines should be primed with
lubricant prior to installation. This makes
the subsequent ventilation of the system
easier.
○Observe the specified tightening torques.
When tightening, use a calibrated torque
wrench.
○When working with heavy parts use suit-
able lifting tools.
○Avoid mixing up or wrong assembly
of dismantled parts. Mark these parts
accordingly.
○Do not touch cables or electrical compo-
nents with wet or damp hands.
○Fuses must not be bypassed Replace de-
fective fuses always by fuses of the same
type.
○Ensure proper grounding of the product.
○Ensure proper connection of the protec-
tive conductor.
○Undertake drilling only at non-critical,
non-load bearing parts of the operator’s
machine/ infrastructure. Use any avail-
able boreholes. Do not damage lines and
cables when drilling. Changes to SKF
products are prohibited. This includes
all drilling, welding, flame-cutting, and
grinding work.
○Observe possible abrasion points. Protect
the parts accordingly.
○All components used must be designed
for:
- maximum operating pressure
- max / min ambient temperature
- the lubricant to be supplied
- the ATEX zone required
- the operating / ambient conditions at
the place of usage
1.19 Initial commissioning, daily start-up
Ensure that:
○All safety devices are completely available
and functional
○All connections are correctly connected
○All parts are correctly installed
○All warning labels on the product are
present completely, highly visible and
undamaged
○Illegible or missing warning labels are to
be replaced without delay

- 16 -
951-181-014-EN
Version 16
EN 1. Safety instructions
1.20 Cleaning
○Risk of fire and explosion when using
inflammable cleaning agents Only use
non-flammable cleaning agents suitable
for the purpose.
○Do not use aggressive cleaning agents.
○Thoroughly remove residues of cleaning
agents from the product.
○Do not use steam jet and high pressure
cleaners. Electrical components may be
damaged. Observe the IP type of protec-
tion of the pump.
○Cleaning work may not be carried out on
energized components.
○Mark damp areas accordingly.
1.21 Safety-related protective and emer-
gency devices must
○Safety-related protective and emergency
devices must not be removed, modified or
affected otherwise in their function and are
to be checked at regular intervals for com-
pleteness and function.
○If protective and safety equipment has to
be dismantled, it must be reassembled
immediately after finishing the work, and
then checked for correct function.
Depending on the equipment variant of the
pump the following safety-related protective
and emergency devices are available:
○Sensors for filling-level monitoring
○Mechanical indication of the filling level
○Overload / thermal circuit breaker of the
electric motor
○Pressure relief valves
○Equipotential bonding

1
- 17 -
951-181-014-EN
Version 16
EN
1. Safety instructions
1.22 Special safety instructions
regarding explosion protection
○Always behave so that explosion hazards
are avoided.
○A written work approval from the opera-
tor is required prior to working in poten-
tially explosive areas. Keep unauthorized
persons away
○There must be no indications that parts
of the explosion protection are missing or
are not working. Should such indications
become apparent, switch off the machine
and inform a superior without delay.
○Measures for explosion protection
must never be deactivated, modified or
bypassed.
○Transport damages can result in the loss
of the explosion protection. If transport
damages can be seen, do not assemble
the product nor put it into operation.
○It is forbidden to bring in ignition sources
such as sparks, open flames and hot sur-
faces in potentially explosive areas.
○Check the machine at regular intervals
in line with the operating conditions for
damage which may represent an ignition
risk as well as with regard to correct func-
tioning. An inspection must be carried out
every 12 months at the latest.
○The ignition temperature of the ambient
explosive gas and vapour atmospheres
must be greater than 125 % of the maxi-
mum surface temperature.
○The minimum ignition and glow tem-
perature of the ambient explosive dust
atmospheres must be greater than 150 %
of the maximum surface temperature
○The limits of use related to explosion pro-
tection are clearly defined by the device
categories, gas and dust groups as well
as temperature classes stated in the ex-
plosion protection marking. In any case,
also if dust group IIIC is specified, light-
metal dusts as explosive ambient media
are prohibited
○The filling-level monitoring must be en-
sured by the operator at a high degree of
safety.
○The product may be filled via the res-
ervoir lid only, if there is no potentially
explosive atmosphere. Filling via the fill-
ing port is also possible with a potentially
explosive atmosphere. Connect the filler
pump to the equipotential bonding of the
pump.
○The product may be cleaned only, if there
is no potentially explosive atmosphere.
○The ignition temperature of the lubricant
must lie at least 50K over the maximum
surface temperature of the components.
○In case of products without electrical fill-
ing level control make sure to check the
lubricant filling level at regular intervals.

- 18 -
951-181-014-EN
Version 16
EN 1. Safety instructions
○Only use tools and clothing which are
permitted for use in potentially explosive
areas (ESD).
○Transport, installation, repairs and work
on electrical components may only be
carried out, if it has been ensured that the
atmosphere is not potentially explosive.
○Repairs or modifications to machines
which are protected against explosions
may be carried out only by the manufac-
turer or by a workshop recognized by a
named institution and confirmed in writ-
ing. If the work is not carried out by the
manufacturer, the repairs must be ap-
proved by a named expert and confirmed
in writing. The repairs are to be marked
by a repair sign on the machine, stating
the following:
- Date
- Executing company
- Type of repair
- If applicable, expert's code
○All parts of the earthing concept must be
correctly available and connected with
the superordinate machine.
○If transport lugs are dismantled after
set-up, the threaded bores must be per-
manently sealed in accordance with the
protection class.
○Handle the materials so that no sparks
generated by tilting, falling, sliding, rub-
bing, impacting, etc. If needed, cover
materials with suitable means.
○Never disconnect plug-in connections
when energized. Secure plug-in connec-
tions against inadvertent manual discon-
nection with the safety clips.
○The operator must check critically wheth-
er operation without a low-level signal
might lead to a new risk potential (e.g.
through heat-up of bearing points on the
machine in the area of ignition tempera-
ture in the case of lacking lubrication).
If this cannot be ascertained, provide a
low-level signal or suitable organisational
measures for monitoring of the bearing
point temperature.
○Avoid dust accumulation and remove
dust immediately. Dust accumulations
have a thermally insulating effect and, if
whirled up, generate the formation of a
potentially explosive atmosphere.
○The product must be integrated in the
operator's lightning protection concept.
○All parts are to be checked regularly for
corrosion. Replace the affected parts.
○Terminal boxes must be firmly closed and
the cable breakthroughs correctly sealed.
○Additional electrical monitoring devices
must be firmly connected and correctly
adjusted.

1
- 19 -
951-181-014-EN
Version 16
EN
1. Safety instructions
1.23 Expiry of the ATEX approval
The ATEX certificate for this product expires
through:
○Inappropriate usage
○Unauthorized modifications
○Use of non-original SKF spare parts
○non-observance of these instructions
and other applicable documents.
○Use of non-specified lubricants
○Non-observance of the specified mainte-
nance and repair intervals
○Operation with damaged or lacking ATEX
painting orATEX painting done wrongly
later on and not complying with the
standards applicable for ATEX
1.24 Operation in explosion-protected
areas
Operation is permitted only, if in compliance
with:
○All information given in these instructions
or stated in the referenced documents.
○All laws and regulations to be complied
with by the user.
○Information on explosion protection
according to directive 1999/92/EC
(ATEX137).
○ATEX approval.
1.25 Explosion protection marking
The explosion protection marking is found
in chapter "Technical data" and on the type
identification plate of the pump.

- 20 -
951-181-014-EN
Version 16
EN 1. Safety instructions
1.26 Residual risks
Residual risk Possible in life cycle Prevention/ remedy
Personal injury/ material damage due to
falling of raised parts A B C G H K Keep unauthorized persons away. No people may remain under suspended loads. Lift parts with adequate lifting devices.
Personal injury/ material damage due to
tilting or falling of the product because of
non-observance of the stated tightening
torques
B C G Observe the specified tightening torques. Fix the product only to components with sufficient load capacity. If no tightening torques are stated, apply tightening
torques according to the screw size characteristics for 8.8 screws.
Personal injury/ material damage due to
electric shock in case of damage to the
connection cable B C D E F G H Check the connection cable with regard to damages before the first usage and
then at regular intervals. Do not mount cable to moving parts or friction points. If
this cannot be avoided, use spring coils respectively protective conduits.
Personal injury/ damage to material due
to spilled or leaked lubricant B C D F G H K
Be careful when filling the reservoir and when connecting or disconnecting lubri-
cant feed lines. Always use suitable hydraulic screw connections and lubrication
lines for the stated pressures. Do not mount lubrication lines to moving parts or
friction points. If this cannot be avoided, use spring coils respectively protective
conduits.
Life phases:
A = transport, B = installation, C = initial start-up, D = operation, E = cleaning, F = maintenance, G = fault, repair, H = shutdown, K = disposal