Skil Skilsaw 5751 User manual

CIRCULAR SAW
5751 (F0155751..)
SKIL Europe BV - Konijnenberg 60 11/05 2610395130
4825 BD Breda - The Netherlands
www.skileurope.com
www.skileurope.com
INSTRUCTIONS page 8
INSTRUCTIONS page 10
HINWEISE Seite 14
INSTRUCTIES bladz. 17
INSTRUKTIONER sida 20
INSTRUKTION side 23
ANVISNING side 26
OHJEET sivu 29
INSTRUCCIONES pág. 32
INSTRUÇÕES pág. 35
ISTRUZIONI pag. 38
LEÍRÁS oldal 41
POKYNY strana 45
KILAVUZ sayfa 48
INSTRUKCJA strona 51
ИНСТРУКЦИИ страница 54
ІНСТРУКЦІЯ страница 58
O∆ΗΓΙΕΣ σελιδα 61
INSTRUCØIUNI pagina 65
YKA3AНИЕ страница 68
POKYNY strana 72
UPUTE stranica 75
UPUTSTVA stranica 78
NAVODILA stran 81
KASUTUSJUHEND lehekülg 84
INSTRUKCIJA lappuse 87
INSTRUKCIJA puslapis 90
GB
F
D
NL
S
DK
N
FIN
E
P
I
H
CZ
TR
PL
RU
UA
GR
RO
BG
SK
HR
SCG
SLO
EST
LV
LT
ME77

2

D
J
M
C
Q
K
V
P
U
TS

2
1
ACCESSORIES SKIL Nr.
5751
1000 W
3,8 kg
34 mm
45°
51 mm
90°
4800
142 mm
MIN.
20 mm
152 mm
MAX.
20 mm
12x 152 mm 20 mm 1,4 / 2,2 2610372010
24x 152 mm 20 mm 1,4 / 2,4 2610373888
20x 152 mm 20 mm 1,4 / 2,4 2610373889

3

B
E
DFC
A
G
F
3

4
L
K
5
H
J
R
4

5
M
N
J
6
45°0°P
7

6
8

7
V
U
9
D
C
0
!
@

Circular saw 5751
INTRODUCTION
●This tool is intended for lengthways and crossways
cutting of wood with straight cuts as well as angle cuts to
45°; with the appropriate saw blades also non-ferrous
metals, light building materials and plastics can be cut
●Read and save this instruction manual
TECHNICAL SPECIFICATIONS 1
SAFETY
GENERAL SAFETY INSTRUCTIONS
WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains operated
(corded) power tool. SAVE THESE INSTRUCTIONS.
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
GB
8

g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is
maintained.
SAFETY INSTRUCTIONS FOR CIRCULAR SAWS
●Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start cutting
●When you put away the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
●Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
●In case of jamming or electrical or mechanical
malfunction, immediately switch off the tool and
disconnect the plug
●SKIL can assure flawless functioning of the tool only
when original accessories are used
●Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
●Never use the tool without the original protection guard
system
●This tool should not be used by people under the age of
16 years
●The noise level when working can exceed 85 dB(A);
wear ear protection
●If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
●Never use tool when cord is damaged; have it replaced
by a qualified person
●Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
●This tool is not suitable for wet cutting
●The kerf guide has to be adjusted in case different
diameters of sawblade are used
●Do not use a circular saw blade of which the body
thickness is bigger, or the teeth setting is smaller than
the thickness of the kerf guide
●Do not remove the kerf guide
●After switching off your circular saw, never stop the
rotation of the saw blade by a lateral force applied
against it
●Never use circular saw blades made of high speed steel
(HSS)
●Never use grinding/cutting discs with this tool
●Keep hands away from cutting area and the blade
●Do not use a dull or damaged blade
●Do not operate the saw if lower guard does not move
freely and close instantly
●Never clamp or tie the lower guard into the open position
●Do not work materials containing asbestos (asbestos
is considered carcinogenic)
●Take protective measures when during work dust
can develop that is harmful to one's health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/chip
extraction when connectable
●Do not attempt to cut extremely small workpieces
●Remove all obstacles on top of as well as underneath
the cutting path before you start cutting
●Do not work overhead with the tool
●Only use a saw table provided with a switch that
prevents restarting of the motor after interruption of
voltage
●Always disconnect plug from power source before
making any adjustment or changing any accessory
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
●Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
●If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
●Changing saw blade 3
- take hex key A from storage B
- open lower guard C by using lever D
- change saw blade with saw teeth and arrow printed
on saw blade pointing in same direction as arrow E
! make sure that clamping surfaces F of flanges are
perfectly clean and face the blade
- tighten blade bolt G with hex key 1/8 turn past finger
tight (ensures slippage of saw blade when it
encounters excessive resistance thus reducing motor
overload and saw kickback)
●Adjusting cutting depth (0-51 mm) 4
- for an optimal quality cut the saw blade should not
extend more than 3 mm below the workpiece
- loosen knob H
- raise/lower foot F until desired cutting depth is set
- tighten knob H
●Adjusting cutting angle (0-45°) 5
- loosen knob K
- tilt tool until desired cutting angle is set on scale using
indicator L
- tighten knob K
! when bevel cutting, cutting depth does not
correspond with value on cutting depth scale
●Kerf guide M 6
- protects saw blade from getting jammed in the
workpiece
- needs readjustment when min./max. space is affected
or upon changing of saw blade
Readjusting kerf guide 6
- adjust and tighten foot J to maximum cutting depth 4
- loosen bolt N
- adjust kerfguide M
- tighten bolt N
9

●Line-of-cut indicator P 27
- for guiding tool along desired line of cut marked on the
workpiece
- for a straight 0° cut or a 45° bevel cut use the indicator
line concerned
! the wide part of the foot should rest on the
supported part of the workpiece
! cutting width is determined by width of blade
teeth and not by width of blade body
! always make trial cuts first to verify actual line of
cut
●Dust suction
- connect vacuum cleaner to extension Q 2
! never let the vacuum cleaner hose interfere with
the lower guard or the cutting operation
●Operating the tool 2
- connect plug with power source
- always hold the tool firmly with both hands
- keep ventilation slots R 4clear and uncovered
- place tool with front end of foot flat on workpiece
! ensure that the saw teeth are not engaged into the
workpiece
- switch on tool by first pressing knob S (= safety switch
which cannot be locked) and then pulling trigger T
! the tool should run at full speed before the blade
enters into the workpiece
- lower guard C opens automatically when saw blade
enters the workpiece (open lower guard manually by
using lever D only for special cuts such as plunge
cuts)
- do not force the tool; apply light and continuous
pressure
- after completing the cut switch off tool by releasing
trigger T
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece
APPLICATION ADVICE
●Always face the good side of the workpiece down to
ensure minimum splintering
●Only use sharp saw blades of the correct type 8
- quality of cut improves by the number of teeth
- carbide tipped blades stay sharp up to 30 times longer
than ordinary blades
●Rip fence U 29
- for making exact cuts along a workpiece edge
- can be inserted in either side of foot
Adjusting rip fence
- loosen knob V
- adjust to desired cutting width by using rip fence scale
(use line-of-cut indicator P 27as 0-reference)
- tighten knob V
●Plunge cutting 0
- set desired cutting depth
- tilt tool forward with line-of-cut indicator lined up with
desired line of cut marked on the workpiece
- open lower guard C with lever D
- just before blade enters workpiece, switch on tool and
gradually lower back end of tool using front end of foot
as hinge-point
- gradually move tool downward as well as forward as
soon as kerfguide touches the workpiece
- when foot rests flat on workpiece, release lever D
! never pull tool backwards
●Cutting large panels !
- support panel close to the cut either on floor, table or
workbench
! set cutting depth so that you cut through panel
and not through support
- in case rip fence does not allow desired width of cut,
clamp or nail straight piece of wood to workpiece as a
guide, and use the right side of the foot against this
guide
●For more tips see www.skileurope.com
GUARANTEE / ENVIRONMENT
●Always keep tool and cord clean (especially the
ventilation slots)
! disconnect the plug before cleaning
●Clean saw blade immediately after use (especially from
resin and glue)
●This SKIL product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
●In case of a complaint, send the tool undismantled
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
●Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @will remind you of this when the need for
disposing occurs
Scie circulaire 5751
INTRODUCTION
●Cet outil est conçu pour effectuer dans le bois des
coupes droites longitudinales et transversales ainsi que
des angles d’onglet jusqu’à 45°; muni de lames de scie
correspondantes, il est capable de scier des matériaux
non-ferroux, des matériaux de construction légers et des
matières plastiques
●Lisez et conservez ce manuel d’instruction
SPECIFICATIONS TECHNIQUES 1
F
10

94
CE DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in conformity with the following
standards or standardized documents: EN 50 144, EN 55 014, in accordance with the provisions of the directives 73/23/EC,
89/336/EC, 98/37/EC.
NOISE/VIBRATION Measured in accordance with EN 50 144 the sound pressure level of this tool is 95 dB(A), the sound power level
108 dB(A), and the vibration < 2.5 m/s2(hand-arm method).
CE DÉCLARATION DE CONFORMITÉ Nous déclarons sous notre propre responsabilité que ce produit est en conformité avec les
normes ou documents normalisés suivants: EN 50 144, EN 55 014, conforme aux réglementations 73/23/EC, 89/336/EC, 98/37/EC.
BRUIT/VIBRATION Mesuré selon EN 50 144 le niveau de la pression sonore de cet outil est 95 dB(A), le niveau de la puissance
sonore 108 dB(A), et la vibration < 2,5 m/s2(méthode main-bras).
CE KONFORMITÄTSERKLÄRUNG Wir erklären in alleiniger Verantwortung, daß dieses Produkt mit den folgenden Normen oder
normativen Dokumenten übereinstimmt: EN 50 144, EN 55 014, gemäß den Bestimmungen der Richtlinien 73/23/EG, 89/336/EG,
98/37/EG.
GERÄUSCH/VIBRATION Gemessen gemäß EN 50 144 beträgt der Schalldruckpegel dieses Gerätes 95 dB(A), der
Schalleistungspegel 108 dB(A), und die Vibration < 2,5 m/s2(Hand-Arm Methode).
CE CONFORMITEITSVERKLARING Wij verklaren, dat dit product voldoet aan de volgende normen of normatieve documenten:
EN 50 144, EN 55 014, overeenkomstig de bepalingen van de richtlijnen 73/23/EG, 89/336/EG, 98/37/EG.
GELUID/VIBRATIE Gemeten volgens EN 50 144 bedraagt het geluidsdrukniveau van deze machine 95 dB(A), het geluidsvermogen-
niveau 108 dB(A), en de vibratie < 2,5 m/s2(hand-arm methode).
CE KONFORMITETSFÖRKLARING Vi intygar och ansvarar för, att denna produkt överensstämmer med följande norm och
dokument: EN 50 144, EN 55 014, enl. bestämmelser och riktlinjema 73/23/EG, 89/336/EG, 98/37/EG.
LJUD/VIBRATION Ljudtrycksnivån som uppmätts enligt EN 50 144 är på denna maskin 95 dB(A), ljudeffektnivån 108 dB(A), och
vibration < 2,5 m/s2(hand-arm metod).
CE KONFORMITETSERKLÆRING Vi erklærer under almindeligt ansvar, at dette produkt er i overensstemmelse med følgende
normer eller normative dokumenter: EN 50 144, EN 55 014, i henhold til bestemmelserne i direktiverne 73/23/EF, 89/336/EF,
98/37/EF. STØJ/VIBRATION Måles efter EN 50 144 er lydtrykniveau af dette værktøj 95 dB(A), lydeffektniveau
108 dB(A), og vibrationsniveauet < 2,5 m/s2(hånd-arm metoden).
CE SAMSVARSERKLÆRING Vi erklærer at det er under vårt ansvar at dette produkt er i samsvar med følgende standarder eller
standard- dokumenter: EN 50 144, EN 55 014, i samsvar med reguleringer 73/23/EF, 89/336/EF, 98/37/EF.
STØY/VIBRASJON Målt ifølge EN 50 144 er lydtrykknivået av dette verktøyet 95 dB(A), lydstyrkenivået 108 dB(A), og
vibrasjonsnivået < 2,5 m/s2(hånd-arm metode).
CE TODISTUS STANDARDINMUKAISUUDESTA Todistamme täten ja vastaamme yksin siitä, että tämä tuote en allalueteltujen
standardien ja standardoimisasiakirjojen vaatimusten mukainen EN 50 144, EN 55 014, seuraavien sääntöjen mukaisesti 73/23/ETY,
89/336/ETY, 98/37/ETY. MELU/TÄRINÄ Mitattuna EN 50 144 mukaan työkalun melutaso on 95 dB(A), yleensä työkalun äänen
voimakkuus on 108 dB(A), ja tärinän voimakkuus < 2,5 m/s2(käsi-käsivarsi metodi).
CE DECLARACION DE CONFORMIDAD Declaramos bajo nuestra sola responsabilidad que este producto está en conformidad
con las normas o documentos normalizados siguientes: EN 50 144, EN 55 014, de acuerdo con las regulaciones 73/23/CE,
89/336/CE, 98/37/CE.
RUIDOS/VIBRACIONES Medido según EN 50 144 el nivel de la presión acústica de esta herramienta se eleva a 95 dB(A), el nivel
de la potencia acústica 108 dB(A), y la vibración a < 2,5 m/s2(método brazo-mano).
CE DECLARAÇÃO DE CONFIRMIDADE Declaramos sob nossa exclusiva responsabilidade que este producto cumpre as
seguintes normas ou documentos normativos: EN 50 144, EN 55 014, conforme as disposições das directivas 73/23/CE, 89/336/CE,
98/37/CE. RUÍDO/VIBRAÇÕES Medido segundo EN 50 144 o nível de pressão acústica desta ferramenta é 95 dB(A),
o nível de potência acústica 108 dB(A), e a vibração < 2,5 m/s2(método braço-mão).
GB
F
D
NL
S
DK
N
FIN
E
P
05 SKIL Europe B.V. A. v.d. Kloot
CE DICHIARAZIONE DI CONFORMITÀ Dichiaramo, assumendo la piena responsabilità di tale dichiarazione, che il prodotto è
conforme alle seguenti normative e ai relativi documenti: EN 50 144, EN 55 014 in base alle prescrizioni delle direttive CE 73/23,
CE 89/336, CE 98/37.
RUMOROSITÀ/VIBRAZIONE Misurato in conformità al EN 50 144 il livello di pressione acustica di questo utensile è 95 dB(A), il
livello di potenza acustica 108 dB(A), e la vibrazione < 2,5 m/s2(metodo mano-braccio).
I
CE MINÖSÉGI TANUSITVANY Teljes felelösségünk tudatában kijelentjük, hogy jelen termék a következö szabványoknak vagy
kötelezö hatósági elöírásoknak megfelel: EN 50 144, EN 55 014, a 73/23/EK, 89/336/EK, 98/37/EK elöírásoknak megfelelöen.
ZAJ/REZGÉS Az EN 50 144 alapján végzett mérések szerint ezen készülék hangnyomás szintje 95 dB(A), hangteljesítmény szintje
108 dB(A), a kézre ható rezgésszám < 2,5 m/s2.
H
CE STRVZUJÍCÍ PROHLÅ◊ENÍ Potvrzujeme na odpovπdnost, Ωe tento v¥robek odpovídå nåsledujícím normåm nebo normativním
podkladüm: EN 50 144, EN 55 014, podle ustanovení smπrnic 73/23/EG, 89/336/EG, 98/37/EG.
HLUÇNOSTI/VIBRACÍ Mπ®eno podle EN 50 144 çiní tlak hlukové vlny tohoto p®ístroje 95 dB(A),dávka hluçnosti 108 dB(A), a vibrací
< 2,5 m/s2(metoda ruka-paΩe).
CZ
CE STANDARDIZASYON BEYANI Ye¤ane sorumlu olarak, bu ürünün afla¤ıdaki standartlara veya standart belgelerine uygun
oldu¤unu beyan ederiz: EN 50 144, EN 55 014, yönetmeli¤i hükümleri uyarınca 73/23/EC, 89/336/EC, 98/37/EC.
GÜRÜLTÜ//T‹TREfiIM Ölçülen EN 50 144 göre ses basıncı bu makinanın seviyesi 95 dB(A), çal›flma s›ras›ndaki gürültü
108 dB(A), ve titreflim < 2,5 m/s2(el-kol metodu).
TR

95
05 SKIL Europe B.V. A. v.d. Kloot
ЗАЯВЛЕНИЕ О СООТВЕТСТВИИ Мы с полной ответственностыо заявляем, что это изделие соответствует следующим
стандартам или стандартизованным документам: EN 50 144, EN 55 014, в соответсувии с инструкциями 73/23/EC,
89/336/EC, 98/37/EC. ШУМНОСТИ/ВИБРАЦИИ При измерении в соответствии co стандартoм EN 50 144 уровень звукового
давления для этого инструмента составляет 95 дБ (A), уровeнь звуковой мощности - 108 дБ (A), и вибрации -
< 2,5 м/с2(по методу для рук).
RU
CE ВІДПОВІДНІСТЬ Ми заявляємо, що відповідність даного продукту наступним стандартам і регулюючим документам
повністю нашою відповідальністю: EN 50 144, EN 55 014, відповідно до положень директив 73/23/ЄС, 89/336/ЄС, 98/37/ЄС.
ШУМ/ВІБРАЦІЯ Зміряний відповідно до EN 50 144 рівень тиску звуку даного інструменту 95 дБ(А), потужність звуку 108
дБ(А), i вібрація < 2,5 м/с2(ручна методика).
UA
CE ∆ΗΛΩΣΗ ΣYMBATOTΗΤΑΣ ∆ηλούµε υπευθύνως τι το προϊν αυτ είναι κατασκευασµένο σύµφωνα µε τους εξής
κανονισµούς ή κατασκευαστικές συστάσεις: EN 50 144, EN 55 014, κατά τις διατάξεις των κανονισµών της Κοινής Αγοράς
73/23/EK, 89/336/EK, 98/37/EK. ΘΟΡYΒΟ/ΚΡΑ∆ΑΣΜΟYΣ Μετρηµένη σύµφωνα µε EN 50 144 η στάθµη ακουστικής πίεσης
αυτού του εργαλείου ανέρχεται σε 95 dB(A),η στάθµη ηχητικής ισχύoς σε 108 dB(A), και ο κραδασµς σε < 2,5 m/s2
(µεθοδος χειρς/βραχίονα).
GR
DECLARAØIE DE CONFORMITATE CE Declaråm pe proprie råspundere cå acest product este conform cu urmåtoarele standarde
sau documente standardizate: EN 50 144, EN 55 014, în conformitate cu regulile 73/23/EC, 89/336/EC, 98/37/EC.
ZGOMOT/VIBRAØII Måsurat în conformitate cu EN 50 144 nivelul de presiune a sunetului generat de acest instrument este de
95 dB(A),nivelul de putere a sunetului 108 dB(A), iar nivelul vibraøiilor < 2,5 m/s2(metoda mînå - braø).
RO
CE ДЕKЛАPAЦИЯ ЗA CБOTВETCTBИE Декларираме на изцяло наша отговорност, че това изделие е съобразено със
следните стандарти или стандартизирани документи: EN 50 144, EN 55 014, в съответствие с нормативната уредба на
73/23/EG, 89/336/EG, 98/37/EG.
ШУМ/ВИБPAЦИИ Измерено в съответствие с EN 50 144 нивото на звуково налягане на този инструмент е 95 dB(A),нивото
на звукова мощност е 108 dB(A), а вибрациите са < 2,5 m/s2(метод ръка-рамо).
BG
CE IZJAVA O USKLA ĐENOSTI Izjavljujemo uz punu odgovornost da je ovaj proizvod usklađen sa slijedeçim normama i
normativnim dokumentima: EN 50 144, EN 55 014, prema odredbama smjernica 73/23/EG, 89/336/EG, 98/37/EG.
BUCI/VIBRACIJAMA Mjereno prema EN 50 144, prag zvuãnog tlaka ovog elektriãnog alata iznosi 95 dB(A), jakost zvuka
108 dB(A), a vibracija < 2,5 m/s2(postupkom na ‰aci-ruci).
HR
CE IZJAVA O USKLA ĐENOSTI Pod punom odgovorno‰çu izjavljujemo da je ovaj proizvod usklađen sa sledeçim standardima ili
standardizovanim dokumentima: EN 50 144, EN 55 014, u skladu sa odredbama smernica 73/23/EG, 89/336/EG, 98/37/EG.
BUKA/VIBRACIJE Mereno u skladu sa EN 50 144, nivo pritiska zvuka ovog alata iznosi 95 dB(A), jaãina zvuka
108 dB(A), a vibracija < 2,5 m/s2(mereno metodom na ‰aci-ruci).
SCG
IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti:
EN 50 144, EN 55 014, v skladu s predpisi navodil 73/23/EG, 89/336/EG, 98/37/EG.
HRUP/VIBRACIJA Izmerjeno v skladu s predpisom EN 50 144 je raven zvoãnega pritiska za to orodje 95 dB(A), jakosti zvoka
108 dB(A), in vibracija < 2,5 m/s2 (metoda ‘dlan-roka’).
SLO
CE VASTAVUSDEKLARATSIOON Kinnitame ainuvastutajana, et see toode vastab järgmistele standarditele või
normdokumentidele: EN 50 144, EN 55 014 vastavalt direktiivide 73/23/EÜ, 89/336/EÜ, 98/37/EÜ nõuetele.
MÜRA/VIBRATSIOON Vastavalt kooskõlas normiga EN 50 144 läbi viidud mõõtmistele on antud seadme helirõhk 95 dB(A),
helitugevus 108 dB(A), ja vibratsioon < 2,5 m/s2(käe-randme-meetod).
EST
CE DEKLARÅCIJA PAR ATBILST±BU STANDARTIEM Mïs ar pilnu atbild¥bu pazi¿ojam, ka ‰is izstrÇdÇjums atbilst standartiem vai
standartizÇcijas dokumentiem EN 50 144, EN 55 014 un ir saska¿Ç ar direkt¥vÇm 73/23/EG, 89/336/EG, 98/37/EG.
TROKSNIS/VIBRÅCIJA Saska¿Ç ar standartu EN 50 144 noteiktais instrumenta rad¥tÇ trok‰¿a ska¿as spiediena l¥menis ir
95 dB(A), ska¿as jaudas l¥menis ir 108 dB (A), un vibrÇcijas intensitÇte ir < 2,5 m/s2(strÇdÇjot rokas reÏ¥mÇ).
LV
CE KOKYBñS ATITIKTIES DEKLARACIJA Mes atsakingai parei‰kiame, kad ‰is gaminys atitinka tokius standartus ir normatyvinius
dokumentus: EN 50 144, EN 55 014 pagal EEB reglament˜ 73/23/EG, 89/336/EG, 98/37/EG nuostatas.
TRIUK·MINGUMAS/VIBRACIJA ·io prietaiso triuk‰mingumas buvo i‰matuotas pagal EN 50 144 reikalavimus keliamo triuk‰mo
garso slògio lygis siekia 95 dB(A), akustinio galingumo lygis 108 dB(A), ir vibracijos pagreitis rankos pla‰takos srityje tipiniu atveju yra
maÏesnis, kaip < 2,5 m/s2.
LT
CE PREHLÁSENIE O ZHODE Vÿhradne na na√u vlastnú zodpovednos† prehlasujeme, Ωe tento vÿrobok zodpovedá nasledujúcim
normám alebo normovanÿm dokumentom: EN 50 144, EN 55 014, v súlade s predpismi 73/23/EC, 89/336/EC, 98/37/EC.
HLUKU/VIBRÁCIÁCH Merané pod¬a EN 50 144 je úroveµ akustického tlaku tohto nástroja 95 dB(A), úroveµ akustického vÿkonu je
108 dB(A) a vibrácie sú < 2,5 m/s2(metóda ruka - paΩa).
SK
OÂWIADCZENIE ZGODNOÂCI CE Niniejszym oÊwiadczamy ponoszàc osobistà odpowiedzialnoÊç, ˝e produkt wykonany jest zgodnie
z nast´pujàcymi normami i dokumentami normalizujàcymi: EN 50 144, EN 55 014, z godnie z wytycznymi 73/23/WE, 89/336/WE,
98/37/WE. HA¸ASU/WIBRACJE Pomiarów dokonano zgodnie z normà EN 50 144 ciÊnienie akustyczne narz´dzia wynosi 95 dB(A),
poziom mocy akustycznej 108 dB(A), zaÊ wibracje < 2,5 m/s2(metoda d∏oƒ-r´ka).
PL