Skope BME1200-AC User manual

BME ActiveCore
User Manual MAN11080 Rev. 3.2 Oct. 2015
BME1200-AC
SKOPE Bottom Mount Vertical Chiller

SKOPE Warranty Protection
Register now for peace of mind
It’s quick and simple. Take a few minutes to register
your SKOPE product and enjoy more efficient
support plus other warranty benefits. When
registering, make sure you have your cabinet serial
number at hand.
To register online:
Visit our website at www.skope.com/warrantyprotection
then complete and submit the online registration form.
Or freephone:
1800 121 535 (Australia)
0800 947 5673 (New Zealand)
SKOPE 1-year Extended Warranty
Extend your Warranty Protection by 1 year during registration. Please
check you have not already organised an extended warranty through
your dealer at time of purchase. For pricing information on an extended
warranty visit www.skope.com/warrantyprotection
Service & Support
We know you will get years of satisfaction from your new SKOPE
product when you follow a few simple preventative maintenance
guidelines.
Helpful information is available on our website
www.skope.com/serviceandsupport
Thank you for purchasing a SKOPE refrigeration product.

SKOPE BME ActiveCore
User Manual iii
CONTENTS
1 Installation
Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Positioning the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Climate Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chiller Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before Operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Door Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Fitting Door Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Removing Door Handles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Shelf Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Repositioning Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 Operation
Automatic Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
LED Tube Side Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LED Modular Shelf and Side Lighting . . . . . . . . . . . . . . . . . . . . .10
Sign Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Loading Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Electronic Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Faceplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Normal and Energy Saving Modes . . . . . . . . . . . . . . . . . . . . . . . 13
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Door Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Temperature Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Messages and Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3 Servicing
Isolating Electrics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Condenser Coil & Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
LED Tube Side Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LED Modular Shelf and Side Lighting . . . . . . . . . . . . . . . . . . . . .18
Sign Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4Installation
User Manual
SKOPE BME ActiveCore
1Installation
Safety First Always observe safety precautions when using any electrical appliance.
Read these instructions carefully and retain them for future reference.
When the appliance is used by or near young children or infirm persons,
close supervision is necessary, especially to ensure children do not play
with it.
Do not use this appliance for other than its intended use.
Do not cover the grilles or block the entry or exhaust of airflow by
placing objects up against the refrigeration unit.
Do not probe any opening.
Only use this appliance with the voltage specified on the cabinet rating
label affixed to the refrigeration unit.
Ensure the appliance has adequate ventilation as this is essential to
economical, high performance.
Be careful not to touch moving parts and hot surfaces.
For your own safety and that of others, ensure that all electrical work is
done by authorised personnel.
If the power supply flexible cord becomes damaged, it must be replaced
by an authorised service agent or similarly qualified person in order to
avoid a hazard.
Ensure all necessary safety precautions are observed during installation
or removal of the refrigeration unit.
The appliance is not designed to be stable while in motion. Use extreme
caution when moving or transporting it.
Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
Please contact SKOPE Customer Services for advice regarding
disposal of this appliance.
CAUTION
Never overload the power supply, which could damage the
chiller and product. See the rating label inside the cabinet for
the safe power supply and current draw.
WARNING
Always disconnect the chiller from the mains power supply
before cleaning or maintenance.

5
SKOPE BME ActiveCore
Installation
User Manual
Positioning the Cabinet
Climate Class The chiller is designed to operate within a climate class 5 environment (40°C
@ 40% RH). We recommend that you put the chiller in the coolest place
possible because it will use less power and last longer.
Chiller
Location
The location of the chiller may be the single most important decision that will
extend its life and ensure economical, high performance. Allow adequate
space for the door/s to open and close properly. Self-closing doors have
internal torsion bars pretensioned at the factory. Ensure the cabinet sits on
a level surface so that the door shuts and correctly seals, and that the doors
are unobstructed. Level footing also prevents the condensate tray from
overflowing.
Power Cord The chiller has a flexible power cord fitted with a 3-pin plug, which exits the
rear of the cabinet at floor level. Locate the power cord before the cabinet is
moved into position so that it is not trapped behind the cabinet.
Ventilation Ensure there is always at least a 50mm gap around the back, top and
underside of the cabinet. Keep the ventilation slots in the lower front panel
clear at all times. Never store cardboard cartons or other objects in front of
the chiller.
Before
Operating Ensure both rear spacers are fully extended outwards and locked into place.
This will provide the necessary air gap at the rear of the cabinet for correct
operation.
CAUTION
To prevent over heating and conserve energy, ensure air flows
freely all around the chiller - including front, back, top and
underside (minimum 50mm gap).
Back of chiller
Rear spacer

6Installation
User Manual
SKOPE BME ActiveCore
Door Handles
Fitting Door
Handles
For transit purposes the door handles may be packed separately inside the
cabinet. If the door handles are packed separately, follow the steps below to
fit them to the door/s.
To fit a door handle
1. Remove the handle/s from inside the cabinet by carefully cutting the cable
ties securing the handle, and remove the packaging.
2. A metal spring clip is
fitted inside the handle
mounts at each end of
the handle.
Rotate the handle so that
the spring clips point up.
3. Locate both of the
handle mounts onto the
brackets on the front of
the door, and push the
handle down onto the
brackets until an audible
click is heard and the
handle locks into place.
If the handle does not lock into place, check the orientation of the handle
and try again.
If only one end of the handle locks into place, follow the steps over the page
to remove the door handle, and refit ensuring both of the handle mounts are
located onto the brackets before pushing the handle down and locking into
place.
Handle mount
Spring clip
(pointing up)
Handle
Bracket
Front of
door
Bracket

7
SKOPE BME ActiveCore
Installation
User Manual
Removing
Door Handles
The door handles can be removed for transporting and moving the cabinet
through doorways.
To remove a door handle
1. Open the door, and peel back the door gasket from behind the handle
mounts on the inside of the door frame.
2. Unscrew the handle mounts through the holes on the inside of the door
frame, and remove the handle.
3. Remove the bracket/s
from the handle mount
by pressing the bracket
in and down until it
unclips from the handle
mount.
4. Fit and screw the
bracket/s back onto the
door. Ensure the catches
are pointing up as
pictured.
5. Refit the door gasket by clipping it back into place on the inside of the door
frame. If the gasket is out of shape after refitting it, a hair drier can be used
to heat and reshape it.
Bracket
Handle mount
Handle
Bracket
Catch
Catch

8Installation
User Manual
SKOPE BME ActiveCore
Shelves
The chiller is fitted with wire shelves, which may be positioned at different
heights to suit various products, and solid bottom shelf/ves. Solid bottom
shelves are held in place by brackets attached to the floor of the chiller. It is
important that solid bottom shelf/ves are always in place as they direct the
interior air circulation.
Interior shelf lit cabinets incorporate cabinet interior lights on the front of
each shelf (see “LED Modular Shelf and Side Lighting” on page 10).
Shelf Clips Each wire shelf is held in place with four shelf clips, which engage in the
shelf support strips and slide up and down to the desired shelf position.
The support strips are numbered for easy location of shelf clips. View the
numbers in the bottom LH corner of the shelf clip.
To fit a shelf clip
To slide a shelf clip up and down
To remove a shelf clip
IMPORTANT
For correct chiller operation, the bottom shelf/ves must always
be in place at the bottom of the chiller.
1. The shelf clip twists onto
the shelf support strip.
Position the shelf clip
with the flat side up
against the shelf support
strip and the two prongs
pointing up. Twist the top
of the clip anticlockwise
onto the shelf support
strip until it locks in
place.
1. Pull the shelf clip tab up
and slide the shelf clip
up or down as required.
Once in position, ensure
the shelf clip is locked
into place.
1. Pull the shelf clip tab up and twist the top of the clip clockwise off the shelf
support strip.
Shelf
support
strip
Prongs
Shelf clip
Shelf clip
Tab

9
SKOPE BME ActiveCore
Installation
User Manual
Repositioning
Shelves When repositioning standard shelves, unload and remove the shelf,
establish the desired position and slide the shelf clip in each of the shelf
support strips to the desired position (see “To slide a shelf clip up and down”
on page 8). Sit the shelves on the shelf clips.
When repositioning shelves fitted with shelf lights, the height is adjusted as
per normal with the shelf clips. The shelves can be repositioned as far as the
shelf light cable reasonably allows via the fixed cut out in the side channel
cover (see procedure below).
To reposition shelves fitted with lights
1. Isolate the chiller from the power supply (see “Isolating Electrics” on
page 15).
2. Remove product from the shelf required to be moved, and from the shelf
immediately above it.
3. Establish the desired shelf position.
4. Support the weight of the shelf and lift it up off the shelf clips. Be careful not
to damage the connected shelf light cables running through the front shelf
clips.
5. Slide the shelf clip in each of the shelf support strips to the desired position
(see “To slide a shelf clip up and down” on page 8).
The shelves can be repositioned as far as the shelf light cable reasonably
allows.
6. After the shelves have been securely positioned, connect cabinet to the
power supply and check for correct operation.
7. Reload the shelves with product.

10 Operation
User Manual
SKOPE BME ActiveCore
2Operation
Automatic Start-Up
After the cabinet has been positioned in a suitable place, plug it in and check
the following activity.
Lighting
The cabinet interior lighting will consist of either LED tube side lights, or LED
modular shelf and side lighting. The cabinet may also be fitted with a top
sign assembly which is lit by an LED tube.
The cabinet lighting will automatically switch on and off depending on chiller
usage. The lights can also be manually switched on and off using the light
button on the electronic controller faceplate (see page 12).
LED Tube Side
Light
Cabinets with LED tube side lights are fitted with LED tube/s which can be
replaced without moving shelves or product (see page 18 for replacement
instructions).
LED Modular
Shelf and Side
Lighting
Cabinets with LED modular shelf and side lighting are lit by shelf lights
mounted on the front of the shelves (two lights per shelf), and LED side
lights. LED modular light components are all non-serviceable items and
must not be tampered with in any way. If a component is suspected of being
faulty, a service call should be arranged so that a replacement component
can be fitted.
Sign Light Cabinets with a lit sign are fitted with an LED tube, located inside the top sign
assembly. In the event of sign light failure, a service call should be arranged
so that a replacement LED tube can be fitted.
Item Activity
Electronic
Controller
An electronic controller runs the chiller and is visible behind
the front panel. The display panel first flashes start-up
messages before stabilising on the cabinet temperature.
Lighting The lights that illuminate the sign and cabinet interior will come
on approximately five seconds after the chiller is turned on.
Compressor and
Condenser Fan
The compressor and condenser fan will start approximately
one minute after the chiller is turned on.
To verify, listen for the compressor and check that the
COMPRESSOR light is lit on the electronic controller. The
compressor and condenser fan will turn off when the product
temperature reaches around +2°C, and on again when it
reaches about +4°C (SKOPE BME ActiveCore default
settings).
Evaporator Fan
The evaporator fan starts approximately three seconds after
the compressor and condenser fan. To verify, check that the
FAN light is lit on the electronic controller.

11
SKOPE BME ActiveCore
Operation
User Manual
Loading Product
Let the chiller run 30 minutes before loading it with product the first time.
When loading the shelves with product:
Allow adequate air space around each item to ensure even cooling and
efficient operation of the chiller.
Do not exceed a maximum load of 20kg per shelf.
Remove some product if the shelves are flexing.
Do not let anything overhang the shelves because this might stop the
doors from shutting or even break something.
For security, there is a lock bracket above the door where you can attach a
padlock and secure the door.

12 Operation
User Manual
SKOPE BME ActiveCore
Electronic Controller
Introduction The chiller is fitted with a Carel S4 electronic controller which is visible
through a cutout in the cabinet front panel. The electronic controller is pre-
programmed and requires no initial setup or additional programming.
SKOPE does not recommend that the settings be changed unless it is
absolutely necessary.
To achieve energy efficient operation, the electronic controller uses
temperature probes and door switches to monitor chiller usage and switch
the chiller between ‘Normal’ and ‘Energy Saving’ modes, control and display
the chiller temperature, collect data, signal temperature alarms and force a
defrost cycle when required.
Faceplate Because the electronic controller plays such an important role, it’s helpful to
know the parts of the faceplate you may use.
CAUTION
The electronic controller must only be adjusted by an
authorised service agent.
ES
12
3
4
5
68
7
No. Item Description
1
Digital display of cabinet temperature or messages. The
temperature is what the sensor inside the chiller detects, and
not necessarily the product temperature. However, they may
be very close depending on how the controller is set to sense
temperature.
2
Energy Save (up): Button. Press to view the current chiller
mode. ‘ECO’ = Energy Saving and ‘nor’ = Normal. Press and
hold for 3 seconds to switch the chiller between ‘Energy
Save’ and ‘Normal’ mode.
3Set (mute): Button. Press to mute the alarm. Press and hold
to access parameters.
4Light (down): Button. Press and hold to switch the cabinet
lights on and off.
5
Defrost: Indicator. ON when the defrost is activated. Flashes
when the activation of the defrost is temporarily delayed due
to procedures in progress.
6
Compressor: Indicator. ON when the compressor and
condenser fan starts. Flashes when activation of the
compressor is temporarily delayed.
7
Fan: Indicator. ON when the internal cabinet fans are
activated. Flashes when activation of the fans is temporarily
delayed.
8Alarm: Indicator. ON when alarm is signalled.
ES

13
SKOPE BME ActiveCore
Operation
User Manual
Normal and
Energy Saving
Modes
The electronic controller is programmed to run the chiller in ‘Normal’ mode
or ‘Energy Saving’ mode.
When plugged in, the chiller will run in ‘Normal’ mode. If the front door/s are
not opened for a specified time period (default setting is three hours), the
electronic controller will switch the chiller from ‘Normal’ mode to ‘Energy
Saving’ mode and the cabinet lights will turn off. The electronic controller will
switch the chiller back into ‘Normal’ mode when a door is opened, or after a
specified time period (default setting is nine hours) in ‘Energy Saving’ mode.
To manually switch the chiller between ‘Normal’ and ‘Energy Saving’ modes,
press and hold the Energy Save (up) button on the electronic controller
faceplate.
To change the default times for automatic switching between ‘Normal’ mode
and ‘Energy Saving’ mode, follow the procedures below.
To change the time between ‘Normal’ and ‘Energy Saving’ modes
Lights When in ‘Normal’ mode the cabinet lights are on. When in ‘Energy Saving’
mode the cabinet lights are off. Press the Light button on the electronic
controller faceplate to manually switch the cabinet lights on and off.
1. Press and hold the set button for 3 seconds until PS is
shown on the display, indicating entry into the controller
settings menu.
2. Press the down button to scroll the menu until r6 is
shown on the display.
The r6 value is the time (in hours) without the door
being opened. When this time is reached (during store
closing hours or quiet periods) the electronic controller
will switch the chiller from ‘Normal’ mode to ‘Energy
Saving’ mode. The r6 value must be ≥1 hour.
IMPORTANT
Do not set r6 to 0.
3. Press the set button. The current r6 value (in hours) is shown on the display.
4. Press the up or down button to increase or decease the value (in hourly
increments).
5. Press the set button to temporarily save the new r6 value.
6. Press the down button to scroll the menu until r7 is
shown on the display.
The r7 value is the maximum time (in hours) that the
chiller will stay in ‘Energy Saving’ mode. When this time
is reached the electronic controller will switch the chiller
from ‘Energy Saving’ mode to ‘Normal’ mode.
7. Press the set button. The current r7 value (in hours) is shown on the display.
8. Press the up or down button to increase or decease the value (in hourly
increments).
9. Press the set button to temporarily save the new r7 value.
10. Press and hold the set button for 3 seconds to permanently save the new
values and exit the controller settings menu.

14 Operation
User Manual
SKOPE BME ActiveCore
Door Switch Each door is fitted with a door switch which tells the electronic controller
when the door is opened and closed. If the door is opened for over two
minutes an alarm will sound. Press the set (mute) button on the electronic
controller to mute the alarm.
Temperature
Setpoint
The chiller temperature setpoint is factory set at 2.5°C for storage of
perishable products (all shelves maintain temperatures below 5°C). The
cabinet setpoint can be adjusted between 1°C and 15°C for other specialist
applications if required (see below).
SKOPE do not recommend that the setpoint be changed unless it is
absolutely necessary, and then only by small increments at a time.
To view and adjust the temperature setpoint
Messages and
Alarms
The following table explains messages and alarms that the electronic
controller displays.
1. Press and hold the set button for 3 seconds until PS is
shown on the display, indicating entry into the controller
settings menu.
2. Press the up or down button to scroll the menu until St
is shown on the display.
3. Press the set button. The current setpoint value is shown on the display.
4. Press the up or down button to increase or decease the setpoint value to the
required temperature.
5. Press the set button to temporarily save the setpoint value.
6. Press and hold the set button for 3 seconds to permanently save the setpoint
value and exit the controller settings menu.
Display Description
Message: The chiller is in ‘Normal’ mode and the electronic
controller displays the chiller temperature.
Message: The chiller is in ‘Energy Saving’ mode. When in
Energy Saving mode the temperature inside the chiller is
moderated and the cabinet lights turn off. The lights can be
switched on and off by pressing the light button on the
controller faceplate, and the chiller can be switched into
‘normal’ mode by pressing the Energy Saving button on the
electronic controller faceplate.
Alarm: The front door has remained open for over two minutes.
An alarm sounds, and the compressor and evaporator fan turn
off.
Alarm: Probe failure. A temperature probe has failed and an
alarm sounds. Contact a service agent.
Alarm: There is a refrigeration system error and the controller
turns the chiller off to avoid damage. An alarm sounds, and the
compressor and evaporator fan turn off. Contact a service
agent.

15
SKOPE BME ActiveCore
Servicing
User Manual
3Servicing
Isolating Electrics
The chiller MUST be isolated from the power supply before attempting any
maintenance. Either unplug the cabinet from the wall or use the isolation
switch to turn off electrics to the cabinet and refrigeration unit. The isolation
switch is located behind the cabinet front kick panel, on the right-hand side
of the refrigeration unit compartment.
To isolate the electrics
1. Open the door and undo the fixing screws from the top of the front kick panel.
Pull the kick panel out to remove.
Note: The electronic controller is attached to the front kick panel. Take care of
cables when removing the front kick panel.
2. Switch off (O) the power at the isolation switch, located on the right-hand side
of the refrigeration unit compartment.
3. Once the maintenance work has been completed, remember to turn the
isolation switch back on (I) before refitting the front kick panel.
Isolation switch
Electronic controller
Front kick panel (removed)
Door (open)

16 Servicing
User Manual
SKOPE BME ActiveCore
Cleaning
Cabinet Periodically wipe the inside and outside of the cabinet with a damp cloth,
taking care to keep moisture away from electrical parts. As with any
maintenance, ensure the chiller is isolated from the power supply before
cleaning.
Condenser
Coil & Filter To ensure trouble-free performance, we strongly urge monthly cleaning with
a soft brush to remove dust and fluff. A more thorough cleaning is required
by qualified service personnel every six months. The condenser and filter
must be kept clean for efficient and reliable operation.
The condenser coil is located on the front of the refrigeration unit. The
optional filter is located on the front panel in front of the condenser coil.
The optional filter is disposable and should be replaced when it shows signs
of wear. Do not apply hot water, blow dry or place in dishwasher.
To clean the optional filter
WARNING
Isolate the chiller from the power supply before cleaning the
condenser coil (see page 15).
1. Rotate the grille at the
bottom of the front kick
panel out to gain access
to the filter.
2. To remove the filter, use
the finger loops to pull the
filter up and detach from
the front kick panel.
3. Clean the filter with a vacuum cleaner, wash with cold water and shake
excess water off before refitting. Do not apply hot water, blow dry or place in
dishwasher. If necessary, discard and refit new air filter.
4. To refit the filter, insert it up into the front kick panel vent with the finger loops
facing out. Then clip the into the slots on the bottom face of the front kick
panel vent.
Front kick panel grille
Front kick panel grille
(rotated out)
Finger
loop

17
SKOPE BME ActiveCore
Servicing
User Manual
To clean the condenser coil
1. Remove the front panel and isolate the chiller from the power supply (see
“Isolating Electrics” on page 15).
2. Brush the condenser coil
with a soft brush to
remove any dust and fluff.
3. Turn the isolation switch back on (I) and refit the front panel.
Condenser coil

18 Servicing
User Manual
SKOPE BME ActiveCore
Lighting
This chiller is designed for use with LED tube lights and is not compatible
with fluorescent tubes.
LED Tube Side
Lighting LED tube side lit cabinets are lit by one or two T8 LED tube side lights, which
can be replaced without moving shelves or product. See the table below for
light tube specifications.
Interior light tube specifications
To replace an LED tube side light
LED Modular
Shelf and Side
Lighting
Cabinets with LED modular shelf and side lighting are lit by LED shelf lights
mounted on the front of the shelves (two lights per shelf), and LED side
lights. LED modular light components are all non-serviceable items and
must not be tampered with in any way. If a component is suspected of being
faulty, a service call should be arranged so that a replacement component
can be fitted.
Sign Light BME600-AC and BME1200-AC chillers are fitted with a lit sign. In the event
of sign light failure, a service call should be arranged so that a replacement
LED tube can be fitted.
IMPORTANT
DO NOT use fluorescent tubes.
Item Description
Interior light Eco-Point 20 Watt T8 LED tube (Ø26mm x1350mm)
1. Remove the front kick panel and isolate the chiller from the power supply (see
page 15).
2. Remove the diffuser by
squeezing it until it is
released from the
aluminium housing, and
then push the diffuser out of
the way.
3. Rotate the LED tube until
the pins on the ends of the
tube align with the slots,
then slide it out.
4. Fit a new LED tube. Ensure
the LED tube is fitted with
the ‘Power’ end at the top
(usually marked ‘POWER’
or similar). Note: If present,
the pointer at each end of
the tube should be set to
the “0” position.
5. Refit the diffuser by slipping the back section into the housing, then squeezing
and snapping the front section of the diffuser into place as you work down the
length of the light.
Diffuser
LED Tube
Pins
LED tube
Lamp holder

19
SKOPE BME ActiveCore
Servicing
User Manual
Troubleshooting
For questions about the electronic controller, see page 12. For problems with the cabinet and
refrigeration unit, use the following table.
Problem Possible Cause Suggestions
• Cabinet not operating. • Loss of power supply.
• Isolating switch turned
off.
• Check mains power supply.
• Check isolating switch is turned on (I) (see page 15).
• Controller alarm. • Refer to “Messages and Alarms” on page 14
• No controller display. • Loss of power supply.
• Isolating switch turned
off.
• Check mains power supply.
• Check isolating switch is turned on (I) (see page 15).
• Light not on. • Electronic controller
displays ECO
indicating the chiller is
in ‘Energy Saving’
mode.
• Switch the light on while keeping the chiller in night
mode by pressing the light button on the electronic
controller faceplate.
• Change the chiller into ‘normal’ mode by pressing and
holding the Energy Saving button on the electronic
controller faceplate, or open the door.
• Lights switched off. • Switch light on by pressing the light button on the
electronic controller faceplate.
• Failed LED tube. • Replace LED tube (see page 17).
• Failed LED shelf light. • Contact an authorised service agent to replace it.
• Blown cabinet fuse. • Contact an authorised service agent to replace it.
• Power consumption is
higher than expected.
• unit operating too hot. • Clean or replace the condenser filter (see page 16).
• Clean the condenser (see page 16).
• Ensure the cabinet is in a cool spot (see page 5).
• Ensure the cabinet has good ventilation around the
refrigeration unit (see page 5).
• Cabinet doors are
opened excessively.
• Ensure doors are closed more often.
• Product is too warm. • Restricted airflow to
cabinet.
• Ensure product is not blocking airflow slots.
• Ensure there is space around individual product
pieces.
• Warm cabinet
temperatures.
• Compressor operating
for long periods (more
than 1 hour).
• Blocked condenser. • Clean or replace the condenser filter (see page 16).
• Clean the condenser (see page 16).
• Poor ventilation
around refrigeration
unit.
• Ensure the cabinet has good ventilation around the
refrigeration unit (see page 5).

SKOPE Contacts
SKOPE Industries Limited
NEW ZEALAND CONTACT
Head Office
PO Box 1091, Christchurch
New Zealand
Freephone: 0800 947 5673
Fax: [phone]
E-mail: [email protected]
Website: www.skope.co.nz
AUSTRALIAN CONTACT
A.B.N. 73 374 418 306
PO Box 7543, Baulkham Hills B.C.
NSW 2153, Australia
Freephone: 1800 121 535
Fax: [phone]
E-mail: [email protected]
Website: www.skope.com.au
Trademark Infringement
The SKOPE trademark on this product is infringed if the owner, for the time being, does
any of the following:
• Applies the trade mark to the product after their state, condition, get-up or packaging
has been altered in any manner
• Alters, removes (including part removal) or obliterates (including part obliteration) the
trade mark on the product
• Applies any other trade mark to the product
• Adds to the product any written material that is likely to damage the reputation of the
trade mark
Notice of the above contractual obligations passes to:
• Successors or assignees of the buyer
• Future owners of the product
BME ActiveCore
SKOPE Bottom Mount Vertical Chiller
User Manual
MAN11080
Rev. 3.2 Oct. 2015
© 2015 SKOPE Industries Ltd. All rights reserved.
® SKOPE and the SKOPE logo are registered trade marks of SKOPE Industries Ltd.
ActiveCore and the ActiveCore logo are trade marks of SKOPE Industries Ltd.