Skope BB Series User manual

PRN80321 Rev. 0.6 November 2021 1 of 4
Underbench Display Ranges
Backbar (BB), Counterline (CL), Slimline (SL)
User Guide
Thank you for purchasing a SKOPE refrigeration product.
Safety
Always observe safety precautions when using any electrical appliance. Read these instructions carefully and retain them
for future reference.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Do not use this appliance for other than its intended use.
• Do not insert fingers / foreign objects into any holes.
• Only use this appliance with the voltage specified on the cabinet rating label.
• Ensure the appliance has adequate ventilation as this is essential to economical, high performance.
• Be careful not to touch internal moving parts and hot surfaces.
• For your own safety and that of others, ensure that all electrical work is done by authorised personnel.
• If the power supply flexible cord becomes damaged, it must be replaced by an authorised service agent or similarly qualified
person in order to avoid a hazard.
• Ensure all necessary safety precautions are observed during installation or removal of the refrigeration unit.
• The appliance is not designed to be stable while in motion. Use extreme caution when moving or transporting it.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• If the cabinet is to be scrapped, ensure the cabinet is unplugged from the power supply and cut off the mains flex close to the
back of the cabinet. Be mindful of the risk of animals or children becoming trapped in the appliance - either remove or secure
doors if necessary.
• Refrigerant must be removed by a qualified service person and the cabinet recycled/disposed of in accordance with local
regulations.
WARNING
• Ensure the appliance is disconnected from the power supply before performing any cleaning or maintenance.
• Do not cover the grilles or block the entry or exhaust of airflow by placing objects up against the refrigeration unit.
• Should manual defrosting be necessary, turn off the refrigeration system and allow the ice to melt by air
circulation. Collect ice and water during defrost to prevent a slip hazard. Do not use mechanical methods to
remove ice, as this may damage the refrigeration circuit.
• Do not use any electrical devices or appliances inside the food storage compartment.
This cabinet is designed to operate within a specific climatic class environment.
See the cabinet rating label inside the cabinet for climate class number.
The cabinet includes relevant hazard symbols that may be associated with the
cooler. Refer to the information below for symbol description.
Climate class Ambient temperature Relative humidity WARNING
The refrigeration system contains flammable R290 refrigerant.
Do not tamper with it.
The refrigeration system must only be serviced by qualified
personnel.
325°C 60%
430°C 55%
540°C 40%
7 (tropical) 35°C 75%

PRN80321 Rev. 0.6 November 2021 2 of 4
Installation Guidelines
Ensure the installation guidelines below are considered and met .
Ventilation Requirements
For efficient operation of the chiller, it is essential that adequate ventilation be provided around the front of the
refrigeration unit. Normal operating conditions should not exceed the operating temperature range.
It is critical that the hot refrigeration exhaust air is not restricted and that it can easily flow out and away from the front
of the cabinet. Never store cardboard cartons or other items in front of the refrigeration unit. The ventilation slots on the
unit front cover must be kept clear at all times.
Power Cord
Before final positioning of the cabinet, pull the power cord out and connect to the power supply.
Lights
The interior lights switch on and off automatically depending on usage.
Ventilation
Ensure all ventilation
requirements below are
met.
Door Opening
Allow adequate space for
the door/s to open and
close properly.
Sunlight
Do not install the cabinet
in direct sunlight.
Uneven Surface
Do not install the cabinet
on an uneven surface.
Surface
The installation surface
must be capable of
supporting the loaded
cabinet.
Power Supply
Do not overload the power
supply.
Blocking Ventilation
Do not store boxes or items in
front or on top of the cabinet.
Climate Class
The cabinet must be
installed in an environment
within its climate class.
The climate class is stated
on the cabinet rating label
inside the fridge, and
explained on the front page
of this user guide.
Underbench Display Ranges
Backbar (BB), Counterline (CL), Slimline (SL)

PRN80321 Rev. 0.6 November 2021 3 of 4
Shelves
Each shelf is held in place with four shelf clips, which clip into the shelf support strips. The shelf clips may be positioned
at different heights to suit various product. The shelf clips twist onto the shelf support strips in the cabinet interior.
Use the numbers on the shelf support strips to assist with setting the shelf clips at the same height.
Loading product
Let the cabinet cool down to the desired storage temperature before loading it with product. When loading the cabinet:
Electronic Controller
The electronic controller regulates the cabinet internal temperature, signals alarms and captures
operational information. The internal temperature is factory set for storage of perishable product.
To customise the settings to your requirements and view historical data, download the
SKOPE-connect app from the Google Play Store or Apple App Store, and connect via
Bluetooth
®
wireless technology.
To fit a shelf clip:
Twist anticlockwise onto the shelf support strip.
To remove a shelf clip:
Pull the centre tab up and twist off clockwise.
To adjust the shelf clip height:
Pull the centre tab up and slide up or down as
required. Once in position, ensure it clicks into
place.
Shelf Loading
Do not overload the
shelves
Shelf Flexing
Remove product if the
shelf is flexing
Shelf Overhang
Do not let product
overhang the shelves
Front
Top
Back
Internal Airflow
Leave 25mm space
between product and the
back of cabinet interior
Cabinet Floor
Do not load product
on the cabinet floor.
Use the shelves.
Load Limit
Do not load product
above the load limit
indicators
LOAD LIMIT
MAX
20kg
per shelf
Underbench Display Ranges
Backbar (BB), Counterline (CL), Slimline (SL)

PRN80321 Rev. 0.6 November 2021 4 of 4
Routine Cleaning
Ensure the cabinet is unplugged from the power supply before cleaning.
IMPORTANT: Do NOT use abrasive, corrosive or solvent based cleaners, as this may damage the cabinet finish.
Wipe the inside and outside of the cabinet with a damp cloth, taking care to keep moisture away from electrical parts.
The condenser coil must be kept clean. SKOPE strongly urges monthly cleaning of the condenser coil and air filter.
Do
NOT use hard or sharp tools to clean the coil as these may cause damage.
Service & Support
We know you will get years of satisfaction from your new SKOPE product when you follow a few simple preventative
maintenance guidelines.
Helpful information is available on the SKOPE website: www.skope.com/serviceandsupport
Clean Filter Clean Coil
1• Unplug the cabinet from the
power supply.
2• The filter is located behind the
bottom grille, and is accessed by
lifting the grille up and rotating the
lower end out towards you. Remove
the filter from the cabinet with the
same movement.
3• Clean the filter with a vacuum
cleaner, wash with cold water and
shake off any excess water before
refitting. Do NOT apply hot water,
blow-dry or place in dishwasher.
If necessary, discard and refit new
filter.
1. With the cabinet
unplugged from the
power supply and the
filter removed, brush the
condenser coil with a soft
brush to remove any dust
and fluff.
2. Refit the filter, close the
bottom grille and
reconnect to the power
supply.
Filter
Grille
Coil
Coil
Underbench Display Ranges
Backbar (BB), Counterline (CL), Slimline (SL)