Skyjack SJ-8831FE User manual

Battery Powered
SJ-800E
TM
Series
For Service please call .....................................................................800 275-9522
SkyjackInc.ServiceCenter3451SwensonAve.,St.Charles,IL.60174.... FAX[phone]
For Parts in North America and Asia please call .................................... 800 965-4626
SkyjackInc. Parts Center3451SwensonAve.,St.Charles,IL.60174 ..............FAX[phone]
For Parts & Service in Europe please call....................................................31 297 255 526
SkyjackEuropeCommunicatieweg 29,3641SGMijdrecht Netherlands .............FAX[phone]
117131AH PrintedinCanada Mar.2002
OPERATING MANUAL
This manual MUST be kept and stored with the aerial platform at all times.

WARNING
This Operating Manual and the “ANSI/SIA Manual Of Responsibilities” are considered
fundamental parts of the elevating work platform. They are a very important way to
communicate necessary safety information to users and operators. A complete and
legible copy of these manuals MUST BE KEPT ON THE WORK PLATFORM in the
provided weather resistant storage compartment at all times.

Mar. 2002
SJ-800E Series Battery Powered
117131AH Page 3
1
2
Table Of Contents
S
E
C
T
I
O
N
I
N
D
E
X
Section - Paragraph PageNo.
Section 1 - Introduction
Purpose Of Equipment ....................................................................................................................7
Use Of Equipment............................................................................................................................7
Warnings...........................................................................................................................................7
Description .......................................................................................................................................7
Operator Warnings...........................................................................................................................8
Specifications And Features ............................................................................................................9
Standard Features And Optional Equipment ............................................................................... 10
Work Platform Major Component Identification ...........................................................................11
Section 2 - Operation
Operating Controls Identification ........................................................................................... 13
Base Controls .................................................................................................................................13
Electrical Panel.............................................................................................................................. 13
Emergency Battery Disconnect Switch ........................................................................................13
Base Control Station ......................................................................................................................14
1500W AC Inverter (Option)...........................................................................................................14
Platform Controls ...........................................................................................................................15
Operators’s Control Box ................................................................................................................15
Powered Extension Platform Control Box .................................................................................... 15
Outrigger Control Box....................................................................................................................15
Identification And Operation Of Safety Devices............................................................................16
Operator Qualifications........................................................................................................... 17
Operating Procedures ............................................................................................................. 17
Set-Up Procedure...........................................................................................................................17
Prestart Checks ..............................................................................................................................18
Start and Operation .......................................................................................................................19
Emergency Lowering System .......................................................................................................20
Shutdown Procedure.....................................................................................................................20
Winching and Towing Procedures ................................................................................................21
Outrigger Operating Procedures...................................................................................................22
Electrical Inverter (Option).............................................................................................................23
Battery Service And Charging Procedures...................................................................................23
Battery Charger Operation ............................................................................................................24
Bycan Charger Operation (4825U) ............................................................................................... 24
MAC Charger Operation (#BA1045).............................................................................................25
MAC Charger Operation (#BA1001).............................................................................................26
List Of Tables
TABLE 1-1. Specifications And Features ...................................................... Section 1, Page 9
TABLE 1-2. Standard Features And Optional Equipment ........................... Section 1, Page 10
TABLE 2-1. Owner’s Annual Inspection Record........................................... Section 2, Page 27
TABLE 2-2A. Maximum Platform Capacities................................................... Section 2, Page 28
TABLE 2-2B. Maximum Platform Capacities................................................... Section 2, Page 29
TABLE 2-3. Maintenance And Inspection Schedule .................................... Section 2, Page 30

SJ-800E Series Battery Powered
117131AH
Mar. 2002
Page 4
WARNING
OPERATOR SAFETY REMINDERS
The National Safety Council reminds us that most accidents are caused by the failure of some individuals to
follow simple and fundamental safety rules and precautions. Common sense dictates the use of protective
clothing when working on or near machinery. Use appropriate safety devices to protect your eyes, ears,
hands, feet and body.
You, as a careful operator, are the best insurance against an accident. Therefore, proper usage of this work
platform is mandatory. The following pages of this manual should be read and understood completely before
operating the work platform. Any modifications from the original design are strictly forbidden without written
permission from SKYJACK, Inc.
ANSI/SIA (United States)
You are required by the current ANSI/SIA A92.6 standards to read and understand YOUR
RESPONSIBILITIES in the Manual Of Responsibilities before you use or operate this work platform.
CSA (Canada) and CE (Europe)
You are required to conform to national health and safety regulations applicable to the operation of this
elevating work platform.
FAILURE TO COMPLY with your REQUIRED RESPONSIBILITIES in the use and operation of the
work platform could result in DEATH OR SERIOUS INJURY!
DANGER
ELECTROCUTION HAZARD
THIS MACHINE IS NOT INSULATED. MAINTAIN SAFE CLEARANCES FROM ELECTRICAL
POWER LINES AND APPARATUS. YOU MUST ALLOW FOR PLATFORM SWAY, ROCK OR SAG.
THIS WORK PLATFORM DOES NOT PROVIDE PROTECTION FROM CONTACT WITH OR
PROXIMITY TO AN ELECTRICALLY CHARGED CONDUCTOR.
Minimum Safe Approach Distance
ANSI/SIA A92.6-1999 &
CSA CAN3-B354.2&.3-M82 Requirements CE Guidance Note “Avoidance of danger from Overhead Lines”
Voltage Range Minimum Safe Approach Distance
(Phase to Phase) Feet Meters
0 To 300V Avoid Contact
Over 300V to 50KV 10 3.05
Over 50KV to 200KV 15 4.60
Over 200KV to 350KV 20 6.10
Over 350KV to 500KV 25 7.62
Over 500KV to 750KV 35 10.67
Over 750KV to 1000KV 45 13.72
These machines should not operate within 15M
of overhead lines suspended from steel towers.
These machines should not operate within 9M of
overhead lines suspended from wooden poles.
FAILURE TO AVOID THIS HAZARD WILL RESULT IN DEATH OR SERIOUS INJURY!

Mar. 2002
SJ-800E Series Battery Powered
117131AH Page 5
SERVICE POLICY AND WARRANTY
SKYJACK, Inc. warrants each new SJ800E Series work platform to be free of defective parts and workmanship
for the first 12 months. Any defective part will be replaced or repaired by your local SKYJACK dealer at no
charge for parts or labor. Refer to Warranty Statement for extensions or exclusions.
NOTE
SKYJACK, Inc. is continuously improving and expanding product features on it’s equipment, therefore,
specifications and dimensions are subject to change without notice.
This Safety Alert Symbol Means Attention!
Become Alert! Your Safety Is Involved.
The Safety Alert Symbol identifies important safety messages on machines, safety signs, in manuals, or else-
where. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions
in the safety message.
DO NOT OPERATE THIS EQUIPMENT WITHOUT PROPER
AUTHORIZATION AND TRAINING. DEATH OR SERIOUS
INJURY COULD RESULT FROM IMPROPER USE OF THIS
EQUIPMENT!
SCOPE OF THIS MANUAL
This manual applies to the ANSI/SIA, CSA and CE versions of the SJ800E Series work platform models listed on
Table 1-1. Equipment identified with “ANSI” meets the ANSI/SIA-A92.6 -1990 or ANSI/SIA-A92.6 -1999 standards.
Equipment identified with “CSA” meets the CAN3-B354.2&.3-M82 standards. Equipment identified with “CE”
meets the requirements for the European countries, i.e. Machinery Directive 89/392/EEC and EMC Directive 89/
336/EEC and the corresponding EN standards.

SJ-800E Series Battery Powered
117131AH
Mar. 2002
Page 6
SKYJACK, Inc. warrants each new work platform to
be free of defective parts and workmanship. During
the first full year, labor and replacement parts will be
provided by the local authorized Skyjack dealer
without charge. For the following 48 months,
structural components found to be defective will be
replaced or repaired at no charge.
A warranty registration card is supplied with each
work platform. The warranty is only effective when
the warranty card has been completed and returned
to Skyjack within 15 days from the time of billing.
When work platforms are put into stock, the warranty
period does not start until the work platform has been
shipped to the dealers customer. If a unit is put into
service and no warranty card has been mailed to
Skyjack, Inc., the warranty period will commence 15
days from the date the dealer was invoiced for the
work platform.
All warranty claims are subject to approval by
Skyjack’s Service Department. Skyjack, Inc. reserves
the right to limit or adjust claims with regard to
defective parts, labor or travel time based on usual
and customary guidelines. Parts purchased from
sources other than Skyjack will not be covered under
this warranty. Misuse or improper operation, lack of
normal maintenance and inspections as outlined in
this Operating/Maintenance and Parts Manual,
alterations to original design and/or components or
accidents will void all warranty. Batteries are not
covered by this warranty.
The above mentioned warranty statement is exclusive
and no other warranty whether written, oral or implied
shall apply. Skyjack excludes any implied warranty
of merchantability and fitness and accepts no liability
for consequential damages or for other negligence.
WARRANTY PROCEDURES
The selling distributor or authorized dealer shall be
responsible for the complete handling of customer
claims under this warranty. Here’s what to do:
1. When a customer files a claim under this warranty,
contact Skyjack’s Service Department to verify
warranty coverage. NOTE: The complete serial
number of the work platform is required to verify
the claim.
2. When Skyjack’s Service Department verifies
warranty coverage, they will also issue an RA
(Return Authorization) number for the return of any
defective component(s). All items over $25.00 in
value must be returned to Skyjack, Inc.
Warranty Statement
3. FilloutaWarrantyClaim Formfromdealer’ssupply of
claimforms. ThennotifySkyjack’sServiceDepartment
ofthewarrantyclaimnumberontheformused.
4. The distributor/dealer should then file a warranty claim
with Skyjack, Inc. describing the nature of the defect,
probablecause,workperformed,travelhours,andlabor
hourslistedseparately. Warrantylaborwillbepaidat a
rate of $42.00 per hour. The travel allowance will be
paidatthesamehourlyratewithinthedealersspecified
territory,limitedtoamaximumoffour(4)hours. Ifapart
hasserviceablecomponents,PLEASEreplacethebad
component. Forinstance,ifyouhaveabadswitchona
controller,pleasereplacetheswitch. Hydrauliccylinders
shouldberesealed,unlessthey aredamagedbeyond
repair. Engine failures should be directed to your local
engine distributor and covered by the manufacturers
warranty. Skyjackwillaccommodateyouandyourlabor.
Laborratesandtravelallowancesaresubjecttochange
withoutnotice.
5. Warranty claims must be received by Skyjack within
15 working days from the date of the repair. Warranty
claims received with insufficient information will be
returned for correction or completion.
6. Materials returned for warranty inspection must have
thefollowingprocedures:
A. Carefully packaged to prevent additional damage
duringshipping.
B. Drained of all contents and all open ports capped
or plugged.
C. Shipped in a container tagged or marked with the
RAnumber.
D. ShippedPREPAID. Anyitem(s)returnedforwarranty
byanyothermeansmayberefusedandreturnedunless
prior approval from Skyjack is obtained.
E. Items shipped to the dealer will be sent freight
prepaid and added to the invoice.
Failure to comply with the above procedures may delay
approvalandprocessingofthe warrantyclaimand could
resultin thedenialofawarrantyclaim. Skyjack’sdealer’s
accounts must be kept current in order to approve and
issuewarrantycredits. Skyjackreservestherighttowith-
hold issuance of warranty credits to a dealer if their ac-
count is not in good standing. This is subject to change
without prior notice.

SECTION 1, Page 7Mar. 2002SJ-800E Series Battery Powered
117131AH
Purpose Of Equipment
The SKYJACK SJ-800E Series Work Platform is
designed to transport and raise personnel, tools and
materials to overhead work areas.
Use Of Equipment
The work platform (Figure 1-1.) is a highly
maneuverable, mobile work station. Lifting and
elevated driving MUST be on a flat, level, compacted
surface. The work platform can be driven over uneven
terrain only when the platform is fully lowered.
Warnings
The operator MUST read and completely understand
the safety panel label located on the platform and
ALL other warnings in this manual and on the work
platform. Compare the labels on the work platform
with the labels found throughout this manual. If any
labels are damaged or missing, replace them
immediately.
Description
The work platform consists of three major assemblies,
the platform, lifting mechanism and the base. An
operator’s control box is mounted on the platform
railing. Auxiliary and emergency controls are located
at the base.
Platform
The platform is constructed of a tubular support frame,
a skid-resistant “diamond plate” deck surface, and
43-1/2" (1.10m) hinged railings with 6" (15.24cm) toe
boards and mid-rails. The platform can be entered
from either side through a spring returned gate. All
models can be equipped with a front or both front
and rear extension platforms.
Lifting Mechanism
The lifting mechanism is constructed from steel tubing
making up a scissor-type assembly. The scissor-type
assembly is raised and lowered by single-acting
hydraulic lift cylinders with holding valves. A single-
section pump, driven by the electric traction motor
through a gear box provides hydraulic power to the
lift cylinders. A safety bar located inside the lifting
mechanism prevents (when properly positioned) the
scissor-type assembly from being lowered while
maintenance or repairs are being performed within
the lifting mechanism.
Base
The base is a rigid one-piece weldment which
supports two component side cabinets. One cabinet
contains the hydraulic components, up/down
controls and electrical components. The other
cabinet contains the hydraulic tank. The front axle
has two wheels, steerable by a hydraulic cylinder
and is non-driven or drive shaft/gear box driven (4WD
option). The rear axle is drive shaft/gear box driven
and has a spring-applied hydraulically-released disc
parking brake. The drive system is designed to
automatically adjust to rough terrain or steep
inclines. A slide-out drawer at the front of the base,
supports a battery compartment which provides
power to the electrical system.
Operator’s Control Box
A removable control box, mounted at the right front
of the platform, contains controls for work platform
motion and emergency stopping.
Manual Storage Box
This weather resistant box is mounted to the inside
of the hydraulic cabinet door at the base. It contains
the Operating Manual, the Operating/Maintenance
and Parts Manual and other important
documentation. The Operating Manual for this make
and model work platform MUST remain with the work
platform and should be stored in this box.
Hydraulic Outriggers (if equipped)
Hydraulic outriggers are mounted to the four corners
of the base. Controls on the operator’s control box
are used to extend and retract the hydraulic outrigger
cylinders.
Serial Number Nameplate
The serial number nameplate, located at the rear of
the machine, lists the model number, serial number,
machine weight, drive height, capacity and
maximum number of persons, maximum speed,
maximum manual force, maximum incline, platform
height, voltage, system pressure, lift pressure,
ground pressure (tire contact pressure), and date
manufactured. Use this information for proper
operation and maintenance and when ordering
service parts.
1
SECTION 1
INTRODUCTION

SJ-800E Series Battery Powered
117131AH
Mar. 2002SECTION 1, Page 8
Warning
Work Platform Conditions
An Operator Should Not Use Any
Work Platform That:
• Has ladders, scaffolding or other devices
mounted on it to increase its size or work
height.
• Does not have a clean, uncluttered work area.
• Does not appear to be working properly.
• Has been damaged or appears to have worn
or missing parts.
• Has alterations or modifications not approved
by the manufacturer.
• Has safety devices which have been altered or
disabled.
Operator Warnings
Warning
DO NOT exert excessive side forces on platform
whileelevated.
DO NOT overload, the lift relief valve does not
protect against overloading when the
platformis elevated.
DO NOT alterordisablelimitswitchesorothersafety
devices.
DO NOT exceedtheratedcapacityofyourscissorlift
and make sure the load is evenly
distributed on the platform.
DO NOT raise your platform in windy or gusty
conditions.
Warning
Jobsite Hazards
DO NOT operateonsurfacesnotcapableofholding
weight of the work platform including the
rated load, e.g. covers, drains, and
trenches.
DO NOT elevatetheworkplatformifitis not on firm
level surfaces. Avoid pot holes, loading
docks,debris,dropoffsandsurfacesthat
may affect the stability of your work
platform.
DO NOT climb or descend a grade steeper than
25%. Elevateddrivingmust only be done
onfirm levelsurfaces.(Ref.Table 1-1)
BEAWARE ofoverhead obstacles,andpoorlylitareas
in case of overhead obstacles.
ENSURE that there is no person(s) in the path of
travel.
Optional Accessories
The SKYJACK SJ-800E Series Work Platform is
designed to accept a variety of optional accessories.
These are listed in (Table 1-2.) Standard Features
and Optional Equipment. Operating instructions for
these options (if required) are located in Section 2 of
this manual.

SECTION 1, Page 9Mar. 2002SJ-800E Series Battery Powered
117131AH
Table 1-1. Specifications and Features
8831E 8831FE 8841E 8841FE
Weight* 10,515 lbs.
(4780kg) 11,015 lbs. (5007 kg) 11,440 lbs. (5200 kg) 11,940 lbs. (5427 kg)
Width 87.0”
(2.21m)
Length 137.5”
(3.5m)
Platform
Size 68” x 133.5”
(1.73 x 3.39m)
Working 37.0’
(11.28m) 47.0’ (14.3m)
Platform 31.0’
(9.45m) 41’ (12.5m)
Lowered 59.0”
(1.50m) 69.0” (1.75m)
Height
Drive Full***
Standard 30 x 10-16.5
#6 Air filled 30 x 10-16.5 #6 Foam filled** 30 x 10-16.5 #6 Air filled 30 x 10-16.5 #6 Foam filled**
Tires
Optional #7 or #8 Air filled #7 or #8 Foam filled** #7 or #8 Air filled #7 or #8 Foam filled**
Normal
Drive 2.6 mph
(4.2 km/h)
Elevated Low
Drive .45 mph
(0.8 km/h)
Raise 46 sec. 71 sec.
Speed
Lower 48 sec. 60 sec.
Gradability 30%
∗Weightsshownareforstandard2WDmachinesnoextensionplatforms. Refertoserialnameplateforspecificweight.
∗∗ Solid urethane must be 50 - 55 durometer
∗∗∗ ANSI Only, CE drivable until 26.0’ (7.92 m)

SJ-800E Series Battery Powered
117131AH
Mar. 2002SECTION 1, Page 10
Table 1-2. Standard Features And Optional Equipment
Standard Features (ANSI & CE)
• Operator Horn
• Joystick Control
• Diamond Pattern, All Steel Platform Deck Construction
• Access Ladders and Gates at Both Sides of Platform
• Flashing Light and Descent Alarm
• Hourmeter
• Self-Centering Scissors Design
• Lockable Cabinets With Swing-Out Door
• Color-Coded, Numbered Wiring System
• Tie Down Points
• Hinged Railing System With 6” (15.24cm) Toe Boards
• Battery Compartment Mounted on Slide-Out Tray
• Type #6 Air Filled Tires (Models 8831E & 8841E)
• Type #6F Foam Filled Tires (Model 8831FE & 8841FE)
• AC Outlet on Platform
• Scissor Guards (CE Only)
• Disc Brake System on Rear Axle
• Tilt Alarm with Lift/Drive Cut Out
• Base Control Station
• D-Rings (Lanyard Attachment Points)
• Movement Alarm (ANSI)
Optional Equipment (ANSI & CE)
• Movement Alarm (CE)
• Front and/or Rear Mounted 4 Ft. (1.2m) Powered Extension Platform
• 4 Ft. (1.2m) Slide Out Extension Platform
• 4-Wheel Drive Package
• Rotating Amber Beacon
• Type #6F Foam Filled Tires
• Type #7F Foam Filled Tires
• Type #7 Air Filled Tires
• Type #8 Air Filled Tires
• Independently Operated Hydraulic Outriggers
• Scissor Guards (ANSI Only)
• EE Rating
• 1500 Watt Electrical Inverter

SECTION 1, Page 11Mar. 2002SJ-800E Series Battery Powered
117131AH
Work Platform Major Component Identification
Figure 1-1. SKYJACK SJ-800E Series Work Platform
(Model 8841FE shown)
OPERATOR’S
CONTROL BOX
ENTRY
GATE
MAIN
PLATFORM
LIFTING
MECHANISM
BATTERY
CHARGER/
HYDRAULIC
TANK SIDE
CABINET
BATTERY
TRAY
HYDRAULIC/
ELECTRIC
SIDE
CABINET
BASE
EXTENSION
PLATFORM
(optional)

SECTION 2, Page 13
Mar. 2002
SJ-800E Series Battery Powered
117131AH
SECTION 2
OPERATION
2
Operating Controls Identification
The following descriptions are for identification,
explanation and locating purposes only. A qualified
operator MUST read and completely understand
these descriptions before operating this work
platform. Procedures for operating this work platform
are detailed in the “Operating Procedures” section.
Both standard and optional controls are identified in
this section. Therefore, some controls may be
included that are not furnished on your work platform.
Base Controls
Electrical Panel
Figure 2-1. Electrical Panel
Electrical Panel
This control station is located in the Hydraulic/Electric
side cabinet. It contains the following controls:
1- Hourmeter - Activated when a function is selected,
this gauge records work platform operating time.
2- 20 Amp Circuit Breaker Resets - In the event of
a power overload or positive circuit grounding, circuit
breaker will pop out. Make the necessary corrections,
then depress the push-button to reset.
Emergency Battery Disconnect
Figure 2-2. Emergency Battery Disconnect Switch
1- Emergency Battery Disconnect Switch -
Located at the front of the Pull-Out Battery Tray, these
connectors when separated, disconnect the batteries
and all power to the platform and base control
stations. In the event of an emergency or when
performing maintenance, grasp the handle and pull
the connectors apart.
2- Battery Lockout - This lockout is provided to
prevent unauthorized use and for maintenance
purposes.
1
2
12

SJ-800E Series Battery Powered
117131AH
Mar. 2002
SECTION 2, Page 14
Base Control Station
Figure 2-3A. Base Control Station (ANSI & CSA)
Figure 2-3B Base Control Station (CE)
Base Control Station
This metal control station is mounted on the rear of
the hydraulic/electric side cabinet. It contains the
following controls:
1- Platform Up/Down Toggle Switch - This toggle
type switch raises or lowers the platform to a desired
height.
2- Emergency Stop Button - This red “mushroom-
head” shaped button switch is designed to disengage
power to both the platform and base controls.
3- Base/Platform Toggle Switch (ANSI & CSA) -
When “BASE” position is selected and held, power is
directed to the Base Control Station. NOTE: This
switch is maintained in the “PLATFORM” position.
1500W AC Inverter (Option)
Figure 2-4. 1500W AC Inverter
Inverter - The inverter is located on the base of the
machine, it has the following controls.
1. ON/OFF Switch - This slide switch will activate or
terminates inverter function.
2. Status LEDs - These LEDs indicate the operating
or fault status of the inverter .
3. 15 Amp Circuit Breaker - In the event of a power
overload or circuit grounding, this circuit breaker will
pop out.
4. GFCI Outlet - During inverter operation, this outlet
provides AC power.
2
14
3
1
1
3
2
2

SECTION 2, Page 15
Mar. 2002
SJ-800E Series Battery Powered
117131AH
12
Platform Controls
Operator’s Control Box
Figure 2-5 Operator’s Control Box
Operator’s Control Box
This metal control station is mounted at the right front
of the platform. It contains the following controls:
1- Lift/Drive Function Controller - A one-hand
toggle-type lever to control drive/lift motion and steer
motion. It is a “deadman” control which returns to
neutral when released.
2- Lift/Drive Enable Switch - This momentary
“Trigger” style switch (on later models) energizes the
proportional controller. It must be held depressed
continuously while engaging either the drive/lift or
steer functions.
3- Warning Alarm Indictor Light - Light will glow and
an alarm will sound when an unsafe condition occurs.
4- Platform/Off/Base Select Key Switch (CE) - This
three-way selector switch allows the operator to turn
off the power to the unit or to activate either the base
or platform controls.
5- Emergency Stop Button - This red “mushroom-
head” shaped button switch is designed to disengage
power to the platform controls.
6- Lift/Off/Drive Select Toggle Switch - If “Lift” is
selected, the lift circuit is energized. “OFF”
disconnects power from both the lift and drive circuits.
If “DRIVE” is selected, the drive circuit is energized.
7- Operator Horn Push-Button - This momentary
push-button switch activates an automotive-type horn.
8- Lift/Drive Enable Push-Button (Earlier Models)
- This momentary push-button switch energizes the
lever controller. It must be held depressed while
engaging either the lift or drive functions.
Powered Extension Platform Control Box
Figure 2-6. Powered Extension Control Box
Powered Extension Platform Control Box
1- Enable Switch - This switch, when activated,
brings power to the Platform Extend/Retract Selector
Switch.
2- Platform Extend/Retract Selector Switch - This
switch, when activated, extends or retracts the
platform.
Outrigger Control Box
Figure 2-7. Outrigger Control Box
Outrigger Control Box
This metal box, adjacent to the Operator’s Control
Box, contains toggle switches to control each
outrigger’s extension and retraction.
1- Outrigger Up/Down Control Toggle Switches -
This switch, when activated, extends or retracts
individual outriggers.
1
1 2
7
8
3
4
5
7
6

SJ-800E Series Battery Powered
117131AH
Mar. 2002
SECTION 2, Page 16
Identification And Operation Of
Safety Devices
Manual Safety Bar
Figure 2-8. Safety Bar
1. Safety Bar - Designed to support the scissors
assembly (when properly positioned), the safety bar
MUST be used for inspection and performing
maintenance or repairs within the scissors assembly.
To lower safety bar, push lock lever rearward and the
safety bar will drop. Follow procedure on safety bar
decal to properly position safety bar.
Warning
Crushing Hazard
DO NOT reach through the scissor assembly when
the platform is raised without the safety bar properly
positioned. Lower the platform until the scissor as-
sembly is firmly supported by the safety bar. Failure
to avoid this hazard will result in death or serious
injury!
Warning Alarm And Indictor Light
Light Indicator on control box (Figure 2-5) will glow
and an alarm will sound when an unsafe condition
occurs. Examples are:
1. Machine is in a tilted position.
2. Outriggers are out of a set position. (Not Fully
extended or retracted.) (if equipped)
3. Platform is overloaded. (If equipped with an
overload pressure switch.)
Correct the unsafe condition to resume normal
operation.
Fold-Down Guardrail System
Figure 2-9. Fold-Down Guardrail System
Fold-Down Guardrail System
This system when folded down, reduces the shut
height of the work platform for transporting and
travelling through doorways.
1- Guardrail Locking Pin With Lanyard - To fold the
guardrail system down, remove the locking pin at
each pivot point and lower each guardrail. To raise
the guardrail system, swing up each guardrail and
lock in place with the locking pins ensuring that the
detent ball of each pin is clear of the side of the pivot
brackets. (Figure 2-10.)
Warning
The guardrail system MUST be upright and locked in
place before resuming normal operation. Check the
guardrail system for loose or missing locking pins
before operating this equipment!
Figure 2-10. Correct Position of Locking Pin
DETENT BALL CLEAR OF
SIDE OF PIVOT BRACKET
1
1

SECTION 2, Page 17
Mar. 2002
SJ-800E Series Battery Powered
117131AH
Operator Qualifications
Only trained and authorized persons should use this
work platform. Safe use of this work platform requires
the operator to understand the limitations and
warnings, operating procedures and operator’s
responsibility for maintenance. Accordingly, the
operator MUST understand and be familiar with this
operating manual, its warnings and instructions and
ALL warnings and instructions on the work platform.
Operator also MUST be familiar with employer’s work
rules and related government regulations and be able
to demonstrate his/her ability to understand and
operate THIS make and model work platform in the
presence of a qualified person.
Operating Procedures
The following descriptions are for Operating
Procedures. A qualified operator MUST read and
completely understand these descriptions before
operating this work platform.
Set-Up Procedure
1. Remove all packing materials and inspect for
damage incurred during transport. This is
normally required for equipment being put into
service for the first time, after the equipment
has been unloaded.
Note
Report any damage to delivery carrier immediately.
2. Inspect work platform thoroughly and remove
any foreign objects.
3. Raise the side, extension platform (if so
equipped), and gate railings to their upright
position and lock in place with locking pins.
Lock side railings to front railings with locking
pins. (Refer to Figure 2-10.).
4. Remove the operator’s control box from its
shipping container and secure it to the railing
at the right front of the platform. Attach the
control cable and power deck extension cable
(if so equipped) to the scissor’s control cable.
Warning
Explosion Hazard
Keep flames and sparks away. DO NOT smoke near
batteries. First Aid
Immediatelyflusheyes withcoldwaterifelectrolytic acid
is splattered into them. Seek medical attention if
discomfort continues.
5. Unlock and roll out the battery tray. In the battery
tray, check the electrolyte level in all eight
batteries. If plates are not covered, carefully add
distilled or demineralized water. If needed, check
the specific gravity in each battery, it should be
1.260 to 1.275. (This reading will not be correct
if you just added water to the batteries.)
6. Connect the A.C. battery charger cord to the
proper A.C. voltage source and charge the
batteries. (Refer to “Battery Charging
Procedures”).
7. When charger cycle is complete, disconnect the
battery charger A.C. cord and return the battery
tray to the locked closed position. Ensure that
the Emergency Battery Disconnect is properly
connected and all the Emergency Stop Switches
are pulled out.
8. In the hydraulic/electric cabinet, check the
hydraulic oil level (scissors MUST be fully
lowered) in the tank. Level should be at or
slightly above the top mark on the gauge. If
required, add a quality grade hydraulic oil such
as ATF Dextron III (ESSO). Refer to the
“HYDRAULIC OIL” label located on the oil
reservoir for specific applications.
10A. On (CE) machines:
Raise the platform, by selecting “BASE” position,
with the Platform/Off/Base Select Switch (Figure
2-5.), then from the base control station, push
the base Up/Down Toggle Switch to the “××
××
×” (up)
position until there is an adequate clearance to
swing down and position the safety bar.
10B. On ANSI/SIA and CSA machines:
Raise the platform from the base control station
by pushing the “Base/Platform” switch to the
“base”positionwhilepressingthebaseUp/Down
Toggle Switch to the “××
××
×” (up) position until there
is an adequate clearance to swing down and
position the safety bar.

SJ-800E Series Battery Powered
117131AH
Mar. 2002
SECTION 2, Page 18
11. Release the Safety Bar from it’s storage location
and swing down into position. (Refer to label on
base for proper procedure.) Lower the platform
until the scissor assembly is firmly supported
by the safety bar.
12. Inspect all hoses, fittings, wires, cables, valves,
etc. for leaks, hidden damage and foreign
material.
13A. On (CE) machines:
Raise the platform, by selecting “BASE” position,
with the Platform/Off/Base Select Switch (Figure
2-5.), then from the base control station, push
the base Up/Down Toggle Switch to the “××
××
×” (up)
position until there is an adequate clearance to
swing up the safety bar. Return the safety bar to
the locked storage position
13B. On ANSI/SIA and CSA machines:
Raise the platform from the base control station
by pushing the “Base/Platform” switch to the
“base” position while pressing the base “Up/
Down Toggle Switch” to the “××
××
×” (up) position
until there is an adequate clearance to swing up
the safety bar. Return the safety bar to the locked
storage position.
14. Raise the platform to the maximum extension
height.
Note
Refer to Table 1-1. General Specifications (Section 1)
for raise and lowering times.
15. Fully lower the platform.
16. The SJ800E Series Work Platform is now ready
for use by an authorized, qualified operator who
has read and completely understands ALL of
Section 2, OPERATION in this manual.
Prestart Checks
1. Carefully read and completely understand ALL
of Section 2, OPERATION in this manual and
ALL warnings and instruction labels on the work
platform.
2. Ensure that there are no obstacles around the
work platform and in the path of travel such as
holes, drop offs, ditches, soft fill or debris.
3. Check overhead clearances.
4. Make sure the batteries are fully charged.
Disconnect the AC charger cord from the
external power source.
5. Make sure all guardrails and lockpins are in
place and locked in position
6. Make sure the battery tray and all cabinet doors
are closed.
7. Make sure you do not climb or descend a
grade steeper than 25%. Elevated driving
must only be done on firm level surfaces.
Warning
DO NOT OPERATE THIS EQUIPMENT WITHOUT
PROPER AUTHORIZATION AND TRAINING.
DEATH OR SERIOUS INJURY COULD RESULT
FROM IMPROPER USE OF THIS EQUIPMENT!
OPERATOR’S CHECKLIST
INSPECT AND/OR TEST THE FOLLOWING
DAILY OR AT BEGINNING OF EACH SHIFT
1 OPERATING AND EMERGENCY CONTROLS.
2 SAFETY DEVICES AND LIMIT SWITCHES.
3 PERSONAL PROTECTIVE DEVICES.
4 TIRES AND WHEELS.
5 OUTRIGGERS (IF EQUIPPED) AND OTHER
STRUCTURES.
6 AIR, HYDRAULIC AND FUEL SYSTEM(S) FOR
LEAKS.
7 LOOSE OR MISSING PARTS.
8 CABLES AND WIRING HARNESSES.
9 PLACARDS, WARNINGS, CONTROL MARKINGS
AND OPERATING MANUALS.
10 GUARDRAIL SYSTEM INCLUDING LOCKING PINS.
11 ENGINE OIL LEVEL (IF SO EQUIPPED).
12 BATTERY FLUID LEVEL.
13 HYDRAULIC RESERVOIR LEVEL.
14 COOLANT LEVEL (IF SO EQUIPPED).

SECTION 2, Page 19
Mar. 2002
SJ-800E Series Battery Powered
117131AH
Start and Operation
Using the controls on the base:
1. Ensure that the Emergency Battery Disconnect
is properly connected and the Emergency Stop
Switch is pulled out.
2. Use the ladder at the either side of the work
platform to access the work platform deck.
3. Latch the entry gate.
Using the controls on the platform:
4. Pull out the Emergency Stop Button.
5. Turn key switch to “PLATFORM” position.
6. To Raise or Lower the Platform: Select “LIFT”
position with the Lift/Off/Drive Toggle Switch.
Depress and hold the Enable push-button, then
lift the controller lock ring and push the controller
handle forward to raise or backwards to lower
until a desired height is reached. Release handle
to stop.
Note: Platform lowering is not proportional.
Note
If the tilt alarm sounds and the platform does not, or
only partially raises, immediately lower the platform
and ensure that the machine is on a compacted
LEVEL surface.
Warning
TO PROTECT AGAINST UNINTENDED
MOVEMENT OF THE WORK PLATFORM, PUSH
INTHEEMERGENCYSTOPBUTTONAFTERYOU
HAVE ARRIVED AT YOUR DESIRED LOCATION
ORELEVATION.
7. To Drive Forward or Reverse: Select “DRIVE”
position with the Lift/Off/Drive Toggle Switch.
Depress and hold the Enable push-button, then
lift the controller lock ring and push the controller
handle forward or backwards. Release handle
to stop.
Warning
IF THE MACHINE DOES NOT DRIVE WHEN
ELEVATED, DISENGAGE THE DRIVE
CONTROLLER. LOWER THE PLATFORM
IMMEDIATELY. ENSURE THE MACHINE IS
BEING OPERATED ON A COMPACTED, FIRM
LEVEL SURFACE OR THE TILT SENSOR WILL
DISABLE SOME OR ALL FUNCTIONS.
8. To Sound the Horn: Depress the horn push-
button located on the side of the operator’s
platform control box.
9. To Steer: Select “DRIVE” position with the Lift/
Off/Drive Toggle Switch. Depress and hold the
Enable push-button, then press the rocker on
top of the controller handle in the direction you
wish to steer.
Note: Steering is not proportional.
10. To Extend/Retract the Manual Extension
Platform: Remove the locking pin(s) and push/
pull the extension deck using the push-bar.
Reinsert the locking pin(s) to prevent accidental
movement of the extension platform.
11. To Extend/Retract the Powered Extension
Platform: To extend the platform, select “LIFT”
position with the Lift/Off/Drive Select Switch on
the main platform control box. Then, from the
extension platform control box, activate the
“Enable” switch while toggling the extend/retract
switch to “××
××
×” (extend) position until desired
extension is reached. Release the switch to stop.
To retract the platform, select “LIFT” position with
the Lift/Off/Drive Select Switch on the main
platform control box. Then, from the extension
platform control box, activate the “Enable” switch
while toggling the extend/retract switch to “ØØ
ØØ
Ø”
(retract) position until desired retraction is
reached. Release the switch to stop.

SJ-800E Series Battery Powered
117131AH
Mar. 2002
SECTION 2, Page 20
Shutdown Procedure
1. Fully lower the platform.
2. Turn Key Switch to “OFF” position. Remove key.
3. Push in Emergency Stop Button.
4. Push in Emergency Stop Button located on
Base and remove key. It is not necessary to
separate the Emergency Battery Disconnect
connectors at work platform shutdown
Emergency Lowering System
Figure 2-11. Emergency Lowering System
Emergency Lowering Valve and Holding Valve
Manual Override Knob
This system allows platform lowering in the event of
an electrical system failure. Use the following proce-
dure to lower the platform:
1. Holding Valve Manual Override Knob - Located
on the holding valve at the bottom of each lift cylinder,
these red knurled knobs when depressed and turned
counter-clockwise allow hydraulic oil to bypass each
holding valve. The red knurled knobs on each
holding valve MUST be depressed and turned
clockwise to restore normal operation. A rod for
elevated manual override knob rotation shall be
provided for CE units only.
2. Emergency Lowering Valve - Pull out and hold
the Emergency Lowering Valve plunger, and the
platform will gradually lower. Located at the rear of
the hydraulic/electric side cabinet, this pull-type valve
when used in conjunction with the holding valve
manual overrides, allows platform lowering in the
event of an emergency or electrical system failure.
Activate all holding valve manual override knobs,
then pull and hold the plunger out to lower platform.
Release to stop.
Warning
Crushing Hazard
Keep clear of scissors mechanism when using
emergency lowering valve! After emergency
lowering is completed, the red knurled knobs on
each holding valve MUST be depressed and turned
clockwise to restore normal operation.
1
2

SECTION 2, Page 21
Mar. 2002
SJ-800E Series Battery Powered
117131AH
Winching and Towing Procedures
Warning
When Towing, DO NOT drive onto a downward slope
or brake the towing vehicle rapidly.
Preparation for Winching Or Towing
Parking Brake System
Figure 2-12. Disc Parking Brake
1 - 3. Parking Brake Disc -This device disengages
the brake disc(1) when driving forward or in reverse.
A hydraulic brake cylinder(2), linked to a disc
caliper(3), engages and disengages a brake disc on
the rear axle drive shaft yoke. The brake MUST be
manually disengaged for pushing, towing or
winching. DO NOT push or tow the work platform
onto a downward slope or pull the platform down
an incline towards the winch. The special procedure
for manually disengaging the parking brake is as
follows:
Warning
DO NOT manually disengage the parking brakes if
the work platform is on a slope.
Figure 2-13. Parking Brake Release Hand Pump and
Brake Valve Plunger
4 - 5. Parking Brake Release Hand Pump(4) and
Brake Valve Plunger(5) - Located on the brake
manifold in the hydraulic electric side cabinet, this
hand operated pump MUST be used when pushing,
towing or winching the work platform. To release the
parking brake:
1. Make sure that the work platform is on level
ground. Chock or block the wheels to keep
work platform from rolling.
2. Turn Emergency Power Disconnect Switch to
“OFF” position.
3. Depress the black plunger on the Brake Valve
until the plunger stays in.
4. Grasp the red hand pump plunger and rapidly
depress 60 to 80 times until firm resistance is
felt. The brake is now released.
5. Remove the wheel chocks or blocks, then push,
tow or winch the work platform to the desired
location. When pushing, towing or winching,
DO NOT exceed 2 mph (3.2 km/h). DO NOT
push or tow the platform onto a downward
slope or pull the platform down an incline
towards the winch.
6. Position machine on a firm and level surface.
Chock or block the wheels to prevent the
platform from rolling or re-engage the parking
brakebymomentarily activatingthedrivefunction.
Note
Theparkingbrakewillresetautomaticallywhenthework
platform is put back into service.
1
2
3
45