SkyLink WA-MT User manual

Section 2 - Programming the Sensor with M-Series Main Console
1. Press the learn button on the back
of the M-Series Main Console for
3 seconds until the Zone 1 light
is ashing.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including
interferences that may cause undesired operation.
Congratulations on your purchase of the Skylink Water Leak Sensor
Model: WA-MT. The sensor will detect the water overow and works
with the SkylinkNet Internet Hub and the Skylink M-Series Alert/Alarm System.
INSTALLATION INSTRUCTIONS
Water Leak Sensor
Model: WA-MT
Safety Information
WARNING:
Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
CE - DECLARATION OF CONFORMITY:
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 301489-1, EN301489-3, EN300220-1, EN300220-2 and
EN60950-1. This equipment conforms to the essential requirement of the
1999/5/EC R&TTE Directive.
Parts Description Quantity
A Water Leak Sensor 1
NOTE: You can program in total up to 4 sensors in one zone. If you try to
program the fth sensor, the rst sensor will be removed.
2. Zone 1 is selected. Press the learn
button to select the zone you want
to program the sensor.
4. Once the sensor is programmed,
the Main Console will beep once
and the corresponding zone led
will be off.
A
1B
Section 1 - Insert a battery in the Water Leak Sensor
NOTE: The battery for the Sensor is not included. Please refer to
instruction below to insert an AAA Alkaline Battery.
Learn Button
Section 3 - Programming the Sensor with SkylinkNet Internet Hub
1. Go to “More” and tap
on “System Settings”.
2. Tap on “Setup
Wizard”.
3. Tap on “Add Device”.
NOTE: Programming the sensor with the SkylinkNet Internet Hub
must be done from the SkylinkNet App.
5. Tap on “Water
Sensor”.
6. Name your Sensor,
and location and tap
“Continue”.
7. Tap on “Learn Now”
and follow the video to
activate the sensor.
Package Contents
Mounting Accessories
1. Press both sides and open the cover of the Water Leak Sensor.
2. Insert an AAA Battery in the sensor and close the cover.
Zone LED
3. Activate the Water Leak Sensor
by placing the sensor portion into
the water.
4. Tap on “Sensors”.
B
NOTE:
The transmitter
portion should never be
submerged in water
Transmitter
Sensor
contact

When a sensor failure occurs, try the following:
1. Check if the sensor is located at where it should be.
2. Check if there is any physical damage to the sensor.
3. Move the Main Console closer to the sensor, if the red LED stops ashing,
that means the Main Console or sensor needs to be relocated.
4. Replace the battery of the sensor if the Main Console does not respond
when the sensor is activated within short range.
NOTE: The corresponding zone LED in the Main Console will ash if a sensor
failure or low battery is occurred.
Section 4 - Testing the Sensor with M-Series Alert/Alarm System Section 6 - Installing the Water Leak Sensor
Troubleshooting M-Series Alert/Alarm System
Solution
The M-Series Main Console
panel does not respond to
the sensor?
- You must program the sensor to the control
panel before they can work together.
Can I erase just one sensor
from a zone in the M-Series
Main Console?
- You must erase all the sensors in that zone
and then program the sensor you want to
keep.
Problem
Warranty
ONE YEAR WARRANTY
This product is guaranteed to be free of defects in materials and
workmanship for 1 year from the date of purchase. If this product is
defective, call 1-800-304-1187 for repair or replacement parts.
Guarantee does not include normal wear and tear or batteries.
If you have any questions, problems or missing parts,
please call Skylink Customer Support:
9:00am - 5:00pm EST, Monday-Friday.
Or e-mail us at [email protected]
P/N : 101Y149 Rev:0
©2014 SKYLINK GROUP.
CUSTOMER SERVICE
17 Sheard Avenue,
Brampton, Ontario,
Canada L6Y1J3
1-800-304-1187
www.skylinkhome.com
Section 7 - Battery Indication/Sensor Failure
M-Series Alert/Alarm System
I have multiple sensors in a
zone and the zone LED keep
ashing indicating a sensor
failure. How do I know which
sensor is having the
problem?
- You need to test each sensor individually.
Place the sensor in the appropriate location:
Section 5 - Testing the Sensor with SkylinkNet Alarm System
1. Slide the switch at the back
of the Main Console to
Alert Mode.
2. Activate the Sensor by placing the
sensor contact into the water.
3. The Main Console will start
beeping and ash the Zone
LED.
4. Take out the sensor contact from the
water and wait few seconds until
the alert sound stops.
1. Activate the Sensor by placing
the sensor contact into the
water.
2. The blue icon will turn red indicating
that water leak is detected.
3. Take out the sensor contact
from the water.
4. Wait few seconds and the red icon will
turn back to blue indicating that there
is no water leak detected.
NOTE: Ensure the mounting surface is smooth and clean.
Mount the sensor to the appropriate location with the double-sided tape.
The sensor should be placed higher above ground where the sensor portion can’t
get damaged and the sensor contact should be placed where it can detect the
water level.