SkylinkHome PA-318 User manual
TM
Thank you for your purchase of a SkylinkHome Plug-In ON/OFF Control
(In /Outdoor), Model PA-318. This receiver module allows you to wirelessly
TM
turn on and off connected lights or small appliances with the SkylinkHome
transmitters.
The Plug-In ON/OFF Control (In /Outdoor) PA-318 can communicate with
up to 8 transmitters, so user has the option to add more transmitters to the
system, such as more remote controls, or motion sensors etc.
TM
All wireless signal communications within the SkylinkHome System are
based on rolling code technology to ensure highest security is used.
The following items are included in this package:
- Plug-In ON/OFF Control (In /Outdoor)
- Antenna
- User's Instructions
1. INTRODUCTION
5. SET TIMER DURATION
2. SETUP
3. PROGRAMMING TRANSMITTERS
3. PROGRAMMING TRANSMITTERS (CONT)
Model PA-318
Plug-In ON/OFF Control (In/Outdoor)
Plug-In ON/OFF Control
(In /Outdoor)
PA-318
Insert the antenna to the Plug-In ON/OFF Control
(In/Outdoor) as shown. Place the antenna in
the upright position to have the best reception.
Simply plug the Plug-In ON/OFF Control (In/Outdoor)
to an electrical outlet, then plug in a light or home
appliance to the socket on the Plug-In ON/OFF
Control (In/Outdoor).
The Plug-In ON/OFF Control (In/Outdoor) is designed
to operate maximum load of 1500W at 120VAC.
In order to operate the Plug-In ON/OFF Control (In/Outdoor) remotely,
transmitter or sensor must be programmed to the Plug-In ON/OFF
Control (In /Outdoor). Each module can be operated by up to 8 different
transmitters (or 8 different command signals).
There are 2 operating modes with the Plug-In ON/OFF Control (In/Outdoor):
1) On / Off Mode - When a valid signal is received, it will turn on or off a
load.
2) Countdown Timer Mode - When a valid signal is received, the load will
be on for a specific period of time, either 1 minute, 5 minutes, 15 minutes,
30 minutes, or 60 minutes, then off. This is mainly for energy saving.
To program a transmitter into the Plug-In ON/OFF Control (In/Outdoor),
follow the instructions below:
Before you program a transmitter to the Plug-In ON / OFF Control (In/
Outdoor), decide the operating mode for this transmitter (On/Off Mode or
Countdown Timer Mode).
1. Plug in a load to the Plug-In Module (Indoor / Outdoor)
2. Plug in the module to an AC electrical outlet, the red LED flashes once
quickly. The connected load (i.e. light) should be in off mode.
3. Press and hold the "SET" button for about 3 seconds, the red LED flashes,
meaning it is in On/Off Mode programming sequence. Release the "SET"
button if you are programming a transmitter to operate in On/Off Mode.
4. If you are programming a transmitter to operate in Countdown Timer Mode,
continue to hold the "SET" button for about 10 seconds, until the red LED
is on steadily. Release the "SET" button once the LED is on steadily.
5. Transmit a "Learn" code from the transmitter. Refer to the manual of the
transmitter to transmit this "Learn" code.
6. Once the transmitter is programmed, the red LED flashes quickly then
stops flashing. You have successfully programmed the transmitter.
Red LED
3
1
2
LED Flashing: On/Off Mode
LED Steadily ON: Timer Mode
On / Off
Countdown Timer
Flashing
Steadily On
Note: You must complete the programming sequence within the
15-second interval, otherwise, the module will quit from programming
mode and you need to start again from step 3 if the red LED is off.
Number of Flashes
1
2
3
4
5
This section is for transmitters that are programmed for Countdown Timer
Mode.
The timer can be set to the following duration, meaning the light will stay
on for the following time: 1 minute, 5 minutes, 15 minutes, 30 minutes, or
60 minutes. Only one timer interval can be set. To set the timer duration,
follow the instructions below.
1. Plug in the module to an AC outlet, the red LED flashes once, so it is
powered on properly.
2. Turn on the connected load by a programmed transmitter. The load
must be on under ON/OFF mode in order to set the timer duration.
3. Press and hold the SET button for 3 seconds, the red LED flashes
once. The number of flashes indicates the timer duration:
Timer Duration
1 min.
5 min.
15 min.
30 min.
60 min.
Antenna
4. ON / OFF OPERATION
The PA-318 Plug-In ON/OFF Control (In/Outdoor) allows on / off operation,
when the programmed transmitter is activated.
Depends on the type of transmitter, different functions can be performed
such as:
- Individual On / Off, Zone On / Off, All On, All Off etc.
- Motion Activation
Refer to the user's instructions of the transmitter for detailed instructions .
Note:
When using the Plug-In ON/OFF Control (In/Outdoor) in outdoor, always
connect it to a wall socket so it is hanging down. Placing the unit on
ground level may cause serious damage due to water penetration.
4. Continue to hold the SET button until it reaches the desired setting. The
status will change every 6 seconds, i.e. hold the SET button, you will
see the number of flashes changes from 1 to 2, 2 to 3, etc.
LED Indication
during programming
Operating Mode
8. TECHNICAL SPECIFICATIONS
Input Voltage: 120V AC, 60Hz
Standby Current: 3mA
Maximum Rating: 15 Amps
Maximum Ballast Load: 500W
Maximum Tunsgsten Load: 800W
Maximum Resistive Load: 1500W
Operating Frequency: 318MHz
Range: Up to 500 feet in open area.
Minimum Load: 10W
oo
Operational Temperature: -4 F - 140 F oo
(-20 C - 60 C)
Humidity: 5%-95%
7. ERASING TRANSMITTERS
You may erase a transmitter or sensor from the
module, but you cannot erase a specific device
directly, you must erase all the wireless devices,
then program the ones you want to keep. Follow
the instructions below to erase programmed
transmitters / sensors.
1. Power off the Plug-In Module (Indoor / Outdoor)
by removing it from the AC socket.
2. Press and hold the SET button, while plugging in
the module to an AC outlet.
3. The red LED will be on first, then flashes rapidly
for 1 second, then on and off.
4. You may release the SET button, now
you have successfully erased all the
devices from the lighting receiver.
5. Now you have successfully erased all
the devices.
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101Z700-001 R1
Patent Pending
©2010 SKYLINK GROUP
6. COUNTDOWN TIMER OPERATING MODE
If a transmitter or a sensor is programmed to the Plug-In ON/OFF Control
(In/Outdoor) under the countdown timer mode, when that transmitter is
activated, the load connected will be on for the predetermined timer interval,
the LED on the Plug-In ON/OFF Control will also be on. After the timer
interval, the load will be turned off.
Pressing a programmed button for ON/OFF mode can override timer
operation.
Press and hold the SET
button while plugging
it in to an AC socket
5. SET TIMER DURATION (CONT)
Note: Once the number of flashes reaches 5, it will stay at this setting. If
you would like to go back to other settings, such as 1 flash, release the
button and repeat from step 1 to start over.
Once a transmitter (button) is programmed for timer mode, activating this
programmed transmitter (button) will turn on the light for the specified
timer duration.
During a timer count down, if the module receives another signal for timer
operation, the timer will start again and overrides the previous timer,
therefore, extending the On period by another timer interval.
To stop timer count down, press a programmed button for ON/OFF mode.
9. FCC
The device is approved by the FCC and it complies with Part 15 of the FCC Rules.
Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
11. CUSTOMER SERVICE
12. ACCESSORIES
The Skylink System consists of many other devices such as
SkylinkHome Remotes, Motion Sensor, ON/OFF Wall Switch, Wall
Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF
Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control,
ON/OFF Control, Smart Button Garage Door Control, etc. Please visit
Skylink website at www.skylinkhome.com for more information.
TM
Home
TM
TM
10. WARRANTY
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
If you would like to
-find out the up-to-date specifications
-know more about features and applications
-download documents, i.e. user’s instructions
-order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
