Skytech firegear Outdoors FPB-36L Series User manual

6.875” (Min.)
Cradle Bracket
Cradle Bracket
Cradle Bracket
Cradle Bracket
Pilot Cover
Pilot Cover
Butt Ends Together
Butt Ends Together
Cradle Bracket
Extension Bracket
Figure 1. Side view of burner showing extension bracket.
Combining Linear Burners
Figure 2. Top view installation
NOTICE: Please be aware that when you are combining two linear burners together it is extremely important to size the
gas line for the total Btu’s of both burners together.
The FPB-36L, FPB30L and FPB24L Series re pits can be combined in various combinations to create a longer length re
pit look. This is accomplished by removing the extension bracket (Fig. 1) outlined in the drawing above from each linear
burner you are wanting to combine together. The extension bracket has the angled end and is secured with two screws
on each side. Simply remove the screws and slide the extension bracket off from each burner. Butt the two non-pilot
ends of each burner tight together and keep them level to provide the appearance of one long linear burner (Fig. 2).
REV. 4-6-16

Figure 3. MT (Match Throw) plumbing diagram.
Cradle Bracket
Cradle Bracket
Incoming Gas Line
Key Valve
NOTE: It is required to install seperate key valves
when lighting a MT model to ensure each burner is
lit safely.
Two key valves are required to enable safe lighting of individual burners or you will void the warranty. Without them you
risk delayed ignition of the one burner not being lit at the same time. It is highly recommended to keep the key valves with
in 6-feet of each other and on the same side. See Match Throw lighting instructions below.
REV. 4-6-16
Model Model Minimum Rough Opening Total Btu’s NG Total Btu’s LP
FPB-36LTFS + FPB-36LTFS = 76.25” long x 6.875” wide 110,000 110,000
FPB-36LMT + FPB-36LMT = 76.25” long x 6.875” wide 104,000 104,000
FPB-36LTFS + FPB-30LTFS = 70.25” long x 6.875” wide 97,000 97,000
FPB-36LMT + FPB-30LMT = 70.25” long x 6.875” wide 97,000 100,000
FPB-36LTFS + FPB-24LTFS = 64.25” long x 6.875” wide 90,000 90,000
FPB-36LMT + FPB-24LMT = 64.25” long x 6.875” wide 87,000 90,000
FPB30L-TFS + FPB30L-TFS = 64.25” long x 6.875” wide 84,000 84,000
FPB30L-MT + FPB30L-MT = 64.25” long x 6.875” wide 90,000 90,000
FPB30L-TFS + FPB24L-TFS = 58.25” long x 6.875” wide 77,000 77,000
FPB30L-MT + FPB24L-MT = 58.25” long x 6.875” wide 80,000 80,000
FPB-24LTFS + FPB-24LTFS = 52.25” long x 6.875” wide 70,000 70,000
Table 1
IMPORTANT: Ensure you have proper gas pipe sizing when combining two burners together. Gas pipe
sized too small will cause improper operation from both burners.
Linear Burner Possible Congurations
MATCH THROW (MT) LIGHTING INSTRUCTIONS
ON
OFF
Figure 4. Key Valve Face
READ ALL WARNINGS AND SAFETY INFORMATION IN INSTALLATION MANUAL
BEFORE ATTEMPTING TO LIGHT FIRE PIT
CAUTION: Ensure you have leak tested the re pit before operating.
TURNING ON FIRE PIT
1. Insert key into shut-off valve and secure into square end (see Figs. 4 & 5).
2. Light a long match or butane lighter and hold it near the center of the burner.
3. Turn the key counter-clockwise in gas valve (until it stops) to allow gas to ow and
simultaneously apply the long burning match or Butane lighter as close to the end
burner as possible to light the re pit. See Fig. 10.
4. Gas should ignite within 10 seconds or less. If re pit does not light within 10 seconds
turn key clockwise to turn OFF the gas supply. Ensure there is not too much media on
top of the burner that might inhibit gas ow and try again in 5-minutes.
5. Repeat steps 1 - 4 with the second burner.
MATCH THROW (MT) INSTALLATION

Cradle Bracket
Cradle Bracket
Incoming Gas Line
Valve Box Valve Box
Gas Shut-O Vale
Figure 7. TFS (Thermocouple Flame Sense) plumbing diagram.
Key
Figure 5. Inserting Key into Valve Figure 6. Lighting re pit with lighter
TURNING OFF FIRE PIT
1. Insert key into each shut-off valve and secure into
square end.
2. Turn key clockwise until it stops.
3. Repeat steps 1 and 2 for the second burner.
3. After cooling off install cover.
Butane Lighter
End View
THERMOCOUPLE FLAME SENSE (TFS) INSTALLATION
THERMOCOUPLE FLAME SENSE (TFS) LIGHTING INSTRUCTIONS
READ ALL WARNINGS AND SAFETY INFORMATION IN INSTALLATION MANUAL BEFORE ATTEMPTING TO
LIGHT FIRE PIT
L
O
W
H
I
O
F
F
O
N
Figure 8. Transmitter
TURNING ON FIRE PIT
1. Ensure you have leak tested the re pit before operating. Turn main gas supply ON.
2. Ensure batteries are installed in battery pack and switch is on Latching Solenoid.
3. Press the ON button on the transmitter. You will hear the ignitor probe will begin sparking
for up to 20 seconds and the re pit will turn ON.
4. If the re pit does not light the module will “beep” one time every second indicating an
ignition error. This is a hard lockout. If this occurs press the OFF button on the remote
control and repeat step 1-3.
5. If re pit does not light after second try turn main gas OFF, wait 5 minutes and repeat
steps 1-3.
NOTE: It may take several cycles of ON/OFF to purge the airow from the gas lines. The direct spark ignition
will turn OFF after 20 seconds if the burner does not light after which you will need to press transmitter OFF button then
back ON to initiate ignition again.
Flame height can be adjusted HI and LO. After the re pit is operating press the hand-held transmitter HI or LO. The
transmitter defaults to the HI setting when initially lighting the re pit each time or if attempting to re-light but will
remember the last setting used and change back to that last setting in approximately 5 seconds after lighting.
TURNING OFF FIRE PIT
1. To turn OFF the re pit press the OFF button on the transmitter. Fire pit will turn OFF.
2. After re pit has completely cooled off install cover.
REV. 4-6-16

Always refer to the installation instructions that comes with
each linear re pit for additional information.
Leave this insert for re pit for lighting instructions.
FOR TECHNICAL SERVICE, CALL:
Firegear Outdoors
9230 Conservation Way
Fort Wayne, IN 46809
For Sales: [phone]
WEB SITE: www.regearoutdoors.com
[phone]
REV. 4-6-16