Steelcase Verb Active Media Table User manual

®
3 mm
P2
P2
2
3
4
8 mm
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2017 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Verb®Active Media Table
English - Pages 1 to 20 of 60
French - Pages 21 to 40 of 60
Spanish - Pages 41 to 60 of 60
1094808001 Rev C
LEG ASSEMBLY W/ GLIDE
NEXUS LIFT ASSEMBLY
MEDIA BOX, 43"
SUPPORT BRACE PACKAGE, 51
1102388001
1355399001
1383755001
1383754001
1063469001
6852006
1083322001
DESCRIPTION
TAPERED WORKSURFACE, 43"
TAPERED WORKSURFACE, 34"
RECTANGULAR WORKSURFACE, 43"
RECTANGULAR WORKSURFACE, 34"
ROUNDED WORKSURFACE, 43"
ROUNDED WORKSURFACE, 34"
LEG ASSEMBLY W/ LOCKING CASTER
PARCEL NUMBER
1102393001
1102392001
1102391001
1102390001
1102395001
1102394001
1102387001
ELECTRICAL PACKAGE MODULE
MEDIA BOX, 34"
SUPPORT BRACE PACKAGE, 48

Page 2 of 60
1094808001 Rev C
®
GROUNDED
OUTLET
GROUNDED
OUTLET BOX
GROUNDING
PIN
Figure 2
Grounding methods
DANGER
WARNING
1. Do not allow use by or near children or others who do not understand how to use product safely.
2. Use extra care and unplug power when installing components and routing cables inside monitor cabinet.
Follow all noted cable routing instructions and use cable management components provided to contain and
protect all cabling from damage from moving parts. Use additional cable retaining hardware, as needed, to
ensure that an orderly and safe condition is maintained inside the monitor cabinet.
3. Use only indoors in dry conditions, do not allow liquids to come in contact with the product operating system.
4. Use this table only for its intended use as described in these instructions. Do not use attachments not
recommended by manufacturer.
5. Maximum Table Load = 125 lbs (56.7 kg). Max Monitor Weight = 40 lbs (18.1 kg).
6. This product must be installed in accordance with all applicable state and local codes and ordinances.
Only connect this product to standard electrical power supply of 120VAC-60Hz, 1440 watts.
7. Never operate this table if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged.
8. Confirm appropriate critical components and accessories (identified on page 1) are being used.
X
No children
1. Always unplug this furnishing from the electrical outlet before cleaning or removing components.
2. Improper connections of the equipment-grounding conductor can result in risk of electric shock. Check with a
qualified electrician if you are in doubt as to whether the product is properly grounded. Do not modify the plug
provided with the product - If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This
product is for use on a nominal 120-V circuit and has a grounding plug that looks like the plug illustrated in figure 2.
Make sure that the product is connected to an outlet having the same configurations as the plug.
No adapter should be used with this product.
RISK OF FIRE OR INJURY - ELECTRIC SHOCK
RISK OF INJURY - BURNS, FIRE, ELECTRIC SHOCK, CRUSHING
IMPORTANT SAFETY INSTRUCTIONS

Page 3 of 60
1094808001 Rev C
®
CAUTION
1. Read and follow all technical instructions fully and heed all warnings during installation.
2. It is the installers responsibility to make available all product documentation, and for any users to be familiar with this
product before operation.
3. Do not alter any mechanism components or mounting structure provided with this product.
4. Always exercise care and planning when routing building source power cords to ensure that power cords will not be
damaged.
5. Clean system mechanism only with a clean dry cloth.
6. Refer to Steelcase contact information on page one for questions on product operation or service.
WARNING
10. Keep the cord away from heated surfaces.
11. Never drop or insert any object into any opening.
12. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
13. Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.
14. Do not attempt to open or service electrical control box.
RISK OF INJURY - BURNS, FIRE, ELECTRIC SHOCK, CRUSHING
Continued: RISK OF INJURY - BURNS, FIRE, ELECTRIC SHOCK, CRUSHING

Page 4 of 60
1094808001 Rev C
®
FLAT SCREEN MONITOR REQUIREMENTS:
This product is designed to accommodate a variety of television “flat screen” monitors and provides the required hardware
necessary for their mounting. NOTE: Monitor “not-to-exceed” size dimensions are noted below. Failure to follow these
requirements may result in operational failure and/or product damage.
34 INCH TABLE MAXIMUM MONITOR SIZE:
Width = 29.32 inches (744.7 mm), Height =
21.20 inches (538.5 mm), Depth = 3.50 inches (88.9mm).
43 INCH TABLE MAXIMUM MONITOR SIZE:
Width = 38.32 inches (973.3 mm), Height =
22.70 inches (576.5 mm), Depth = 3.65 inches (92.7 mm).
>1"
(25mm)
Max.
>1"
(25mm)
>1"
(25mm)
>1"
(25mm)

®
Additional Operating Information
ADJUSTING THE HEIGHT LIMIT:
If it is necessary to adjust or set the travel height limit of your lift system -
1. Remove the height limit insert from the port on the control box
2. Using the up/down button, extend the lift column to desired height.
3. Reinstall the height limit insert back into the control box port. This will store the adjusted height setting.
REINITIALIZE:
It may become necessary, to reset the resting height of the lifting column. To reinitialize the lift column
refer to the Initializing information on page 11.
RESETTING LIFT FROM SAFE MODE:
“Safe Mode” occurs when there is an interuption in the power supply when the lift is in operation. This function is noted
by the lift column operating at half speed or less. To reset from safe mode -
1. With power restored, press and hold the down button until the lift is fully retracted.
2. Follow the Initializing procedure from page 11.
SETTING THE HEIGHT LIMIT:
To set the travel height limit of your lift system -
1. Using the up/down button, extend the lift column until the bottom of the monitor screen is flush with the table top surface.
2. Install the height limit insert into the control box port (noted below). This will store the current height setting.
HEIGHT
LIMIT
INSERT
Page 5 of 60
1094808001 Rev C
CONTROL BOX CABLE UP/DOWN SWITCH CABLE
CONTROL BOX

®
1b
1a
(X2)
(X2)
2a 2b
(X14)
(X2)
2c
.875"
(22.2mm)
x36
2
Leg and Top Brace Installation 1
x18
Braces only
used when
worksurface
is 50" long
or longer.
1.125"
(28.6mm)
(X3)
(X6)
1c
Teardrop
shaped hole
(X3)
(X6)
1e
(X3)
1d
Page 6 of 60
1094808001 Rev C

®
1b
1a
c
L
.875"
(22.2mm)
x2
.875"
(22.2mm)
x18
2
1
Wire Manager and Table Bracket Installation
Page 7 of 60
1094808001 Rev C
2a
2b

®
2
.875"
(22.2mm)
x18
3
4
4a 4b
4c
Connecting Table to Cabinet
x6
Page 8 of 60
1094808001 Rev C
.875"
(22.2mm)
1

®
Table to Cabinet Cable Routing
TO POWER
SOURCE
UP/DOWN
SWITCH
TO CONTROL BOX
PORT A1
OPTIONAL RECEPTACLE BOX
RECEPTACLE BOX
.750"
(19.1mm)
x6
CABLE ANCHOR GROMMET
CAUTION:
1
2
3
4
All cabling routed along
cabinet bottom panel
must be routed under the
column support plate.
5
6
.875"
(22.2mm)
x2
Page 9 of 60
1094808001 Rev C

®
2
LIFT COLUMN
CONTROL BOX
UP/DOWN
SWITCH
LIFT SYSTEM WIRING DIAGRAM
TO POWER SOURCE
1A2 A1
AC
3
LIFTING COLUMN CABLE TO CONTROL BOX
LIFT MOTOR CABLE
TO CONTROL BOX
CABLE
Lifting Column Electrical Connections
1
CONTROL BOX
POWER CORD
UP/DOWN SWITCH CABLE
Page 10 of 60
1094808001 Rev C

®
1
3
x2
2
Lifting Column to Cabinet Installation
THUMB SCREWS
BASE
LOCATING
PINS
Page 11 of 60
1094808001 Rev C

®
UP/DOWN SWITCH
Initializing the Lifting Column
IMPORTANT: Before installing the monitor onto the lifting column you must
“ Initialize” the column to pre-set it to it’s at rest height. Failing to complete this
task may affect the mounting of the cabinet top.
1. Check that all electrical cable connections are complete, and that all
cable routing is organized, secured and will not interfere with lift
operation. (See pages 7 and 9).
2. With all electrical cables and connections secure, connect the lifting
column to a power source.
3. Press and hold the “DOWN” button for a full 5 seconds and observe
the column to ensure the ram jogs up and down slightly. If you do
not hear or see any movement, release the button and repeat this
step until a slight jog movement is observed.
4. After successfully completing step 2, press the “UP” button on the
up/down switch to extend the lift column to it’s full extension.
5. Press and release the “DOWN” button to fully retract the lift column
to it’s at rest height.
Page 12 of 60
1094808001 Rev C

®
Installing Monitor Mounting
Components for 34”
Tables
Page 13 of 60
1094808001 Rev C
1
2
NOTE:
Adjust tray height to hang below your
monitor but not bottoming out in box.

®
TOP
ADAPTER PLATE
HARDWARE
BAG
Installing Monitor Mounting
Components for 34”
Tables (Continued)
Page 14 of 60
1094808001 Rev C
3

®
34” Table, Cabinet Top Support Plate and
Monitor to Lift Column Installation
IMPORTANT:
Make sure that the cable is routed
through the two (2) cableclips that were installed onto the
inside of the hanger side panel.
NOTE: Using the up/down switch, extend the lift column
to full height to ease installation of monitor.
NOTE: Assembly shown on this page is for
34” table monitors. To install monitor for 43“
tables, see page 16.
CABLE
CLIPS
2
MONITOR
HANGER
Page 15 of 60
1094808001 Rev C
3b
3a
.750"
(19.1 mm)
x1
ARTICULATING
WIRE MANAGER
x1
0.472"
(12.0 mm)
M6
IMPORTANT:
Make sure the articulating wire
manager is installed and used to contain moving wires to
prevent wire pulling or pinching.
IMPORTANT:
Plastic cover must be installed for lift
mechanism to open lift automatically.
x2
0.630"
(16.0 mm)
M6
1

®
Installing Monitor Mounting Components
for 43” Tables
SCREEN BACK PLATE
1b
1a
2
3
4
.750"
(19.0mm)
x4
Page 16 of 60
1094808001 Rev C
3/8-16
CENTER OF SCREEN
BACK PLATE
1/2 OF MONITOR
SCREEN HEIGHT

®
NOTE: Using the up/down switch, extend the lift column
to full height to ease installation of monitor.
Installing Monitor Mounting Components for 43” Tables
(Continued)
I MPORTANT:
Page 17 of 60
1094808001 Rev C
ARTICULATING
WIRE MANAGER
4a
.750"
(19.1 mm)
x1
x1
0.472"
(12.0 mm)
M6
4b
Make sure the articulating wire
manager is installed and used to contain moving wires to
prevent wire pulling or pinching.
IMPORTANT:
Plastic cover must be installed for lift
mechanism to open lift automatically.
CABLE
CLIPS
3
MONITOR SUPPORT
ASSEMBLY
x2
0.630"
(16.0 mm)
M6
2

®
HANGER
BRACKET
5
TOP
END VIEW
HARDWARE
BAG
EQUAL
OPTIONAL
SPACERS
TOP
MONITOR
SCREEN
HANGER
BRACKET
Installing Monitor Mounting Components for 43” Tables
(Continued)
SQUARE
HANGER
WASHERS
Page 18 of 60
1094808001 Rev C

2
®
END VIEW
HANGER BRACKETS
TOP
43” Table, Monitor to Lift Column Installation
SCREEN BACK PLATE
SCREEN LOCK (X2)
1
4
CAUTION: Use care when lowering the lift column
with mounted monitor screen for the first time. Check
to ensure that no interference will occur between the
monitor screen and cabinet structure.
3
IMPORTANT: Select hanger bracket hooks that
will ensure monitor screen is installed at proper
height. Align monitor screen, horizontally, on
screen back plate. Make sure that both hanger
brackets are fully engaged and that two (2) screen
locks are installed.
Page 19 of 60
1094808001 Rev C
MONITOR SCREEN WITH
VERTICAL HANGER BRACKETS

®
Monitor Screen Wiring Installation
Page 20 of 60
1094808001 Rev C
MONITOR
POWER CORD
CONTROL BOX
POWER CORD
NOTE: Assembly shown on this page is for
34” table monitors. 43“ table monitor conduit
installation is similar.
SAFETY NOTICE: Any cables in the monitor
cabinet that travel vertically during operation of
the lifting column must be enclosed and protected
by the articulating conduit. Ensure that all cables
are routed in a manner that provides free move-
ment thoughout the lifting range and prevents any
pull strain or wear points.