Furniture of America CM7127CK/EK-VN User manual

Assembly Instructions
EASY DIFFICULT
Page 1 of 6
ASSEMBLY RATING
The Assembly Rating is a 5-point system that
shows the degree of effort needed in
assembling a specific product (with 1 being
easy and 5 being difficult). For some
products, two persons are recommended.
2 PERSONS RECOMMENDED
Tools Required For Assembly:
Allen Wrench (Included)
For more information contact our team: [email protected]
Phillips Screwdriver
(Not Included)
CM7127CK/EK-VN
Rev: 19-01-16

Page 2 of 6
BASIC ASSEMBLY TECHNIQUES
FOR YOUR FURNITURE TO LAST,CORRECT ASSEMBLY AND PROPER MAINTENANCE ARE NECESSARY.
PLEASE FOLLOW THE INFORMATION PROVIDED BELOW TO FULLY ENJOY YOUR FURNITURE.
FAILURE TO FOLLOW THE GUIDELINES ABOVE MAY
RESULT IN INJURY AND/OR PROPERTY DAMAGE.
IT IS THE USER'S RESPONSIBILITY TO MAINTAIN THE FURNITURE.THE HARDWARE MAY
LOOSEN OVER TIME AND MAY CAUSE THE FURNITURE TO BE WOBBLY AND UNABLE TO
SUPPORT ITS INTENDED WEIGHT CAPACITY. THIS MAY LEAD TO COLLAPSE AND MAY CAUSE
SERIOUS INJURY.
When lock or spring washer is used in
an assembly, please make sure the
lock or spring washer is placed
between the larger flat washer and the
head of the screw or bolt.
Some furniture comes with height
adjusetment knobs underneath each
leg. To lower or to raise each leg, you
need to turn clockwise or
counterclockwise, respectively.
FURNITURE OF AMERICA.ALL RIGHTS RESERVED.
Make sure all parts are properly
aligned, then use the appropriate
hand tool to completely tighten the
bolts or screws. Do not use power
tools and do not overtighten.
Position each part correctly and insert
screws or bolts into their respective
holes by hand tighten or using the
proper hand tool. Only tighten when
step is completed or when instructed
to do so.
Save the instructions and store the Allen
wrench or any supplied tool for later
maintenance. After two weeks, check and
tighten any loose hardware and repeat
again every six months thereafter.
Use cardboard or carpet area when
assembling furniture to prevent
scratches .Make sure the furniture
rests on a flat and level surface with
each leg evenly touching the floor.
No dragging of products/parts.

#1 x 1pc
#2 x 1pc
Footboard
Headboard
Parts List
Hardware List
Before you begin, please read Page 2
of "Assembly and Care Advice".
And remember, do not tighten until
each step is completed or instructed.
Page 3 of 6
#3 x 2pcs
Side Rail
#4 x 8pcs Ø5/16"
#5 x 1set
Slat (13pcs)
#6 x 4pcs
#7 x 2pcs
HB/FB Foot
Support Rail
Support Leg 30x30x270mm
#A x 8pcs
Bolt Ø5/16" x 1-1/2"
#C x 12pcs
Lock Washer Ø5/16"
#D x 12pcs
Flat Washer Ø5/16"
#E x 1pc
#F x 26pcs
Screw #8 x 38mm
Allen Wrench 5mm
#B x 4pcs
Bolt Ø5/16" x 2-1/2"

Page 4 of 6
Exploded View
# 3
#1
# 6
# 2
# 4
# 3
# 5
# 7
#E
#B
#C
#D
#B x 2pcs
#C x 2pcs
#D x 2pcs
#1
# 6
Align feet (#6) onto the headboard (#1), then secure by
using bolts (#B) with washers (#C,D).

Page 5 of 6
#B x 2pcs
#C x 2pcs
#D x 2pcs
#E
#B
#C
#D
#1
# 6
#E
#A
#C
#D
#A x 8pcs
#C x 8pcs
#D x 8pcs
#1
#2
#3
#3
Align feet (#6) onto the footboard (#2), then secure by using
bolts (#B) with washers (#C,D).
#2
Align side rails (#3) to the headboard (#1) and
footboard (#2), then secure by using bolts (#A)
with washers (#C,D).

Page 6 of 6
#5
#4
#7
#F
#F x 26pcs
# 3
# 3
# 5
Align center slat (#7) to slats (#5), then secure by using support legs
(#4). Adjust the levelers on the support legs (#4) according to ground
level.
Align slats (#5) to the side rails (#3), then secure by using
screws (#F).