Slinex Design Direct Series User manual

{ Design. Uniqueness. Innovations }
DESIGN
DIRECT
SERIES
SL-07IP 7” video door phone
User manual
Thank you for
choosing our equipment

{ Design. Uniqueness. Innovations}DESIGN
DIRECT
SERIES
1Rev. 3.0 2
Attention!
As a result of continuous upgrades and functionality improvements, technical
characteristics of the device can be changed without any preliminary declaration.
This manual can contain some inaccuracy or misprint. The owner reserves the right to
make corrections to the information described in the user manual and device package.
The last revision of this manual is available on www.slinex.com
Safety instructions
Read and keep that manual.
The device installation process should be carried out by the qulied specialists.
Use the device from the –10 ˚C to +55 ˚C, always keep it within that temperature range.
Installation surface should be free from vibration and impact inuence.
Keep this device far from open sources of heat, such as radiators, heaters, and ovens.
The device can be installed near other electronic equipment in case if the temperature of the environment
does not exceed previously mentioned range.
The device should be protected from the direct inuence of the natural phenomena, such as direct sunlight,
rain or snow.
Don’t use aggressive or abradant detergent for the device surface cleaning.
Use soft wet cloth or tissue to remove strong dirt.
Don’t overpower outlets. It can cause re or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that
symbol. Some regions have separation and recycling systems for the electronic
equipment. Connect with local authorities to receive information about recycling of
electronic equipment for your region.
Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other
languages or reproduced in any way including electronic or mechanical.
Document recording and copying is strictly denied without owner permission.
Table of contents
1. Package ............................................................................................................................................................................................3
2. Specication...................................................................................................................................................................................3
3. Description......................................................................................................................................................................................4
4. Installation.......................................................................................................................................................................................5
4.1 Cable requirements.......................................................................................................................................................5
4.2 Schematic diagrams......................................................................................................................................................6
4.3 Unit mount .......................................................................................................................................................................8
5. Operation.........................................................................................................................................................................................9
5.1 Incoming call ...................................................................................................................................................................9
5.2 Door panel and camera image monitoring....................................................................................................... 10
5.3 Incoming call redirection ......................................................................................................................................... 11
5.4 Intercom ......................................................................................................................................................................... 12
6. Monitor settings......................................................................................................................................................................... 12
6.1 Main menu..................................................................................................................................................................... 12
6.2 Display and conversation volume settings........................................................................................................13
7. Network connection diagrams.............................................................................................................................................14
8. Software........................................................................................................................................................................................15
8.1 Creating new account ...............................................................................................................................................15
8.2 Wired network connection steps...........................................................................................................................15
8.3 Wireless Wi-Fi network connection steps...........................................................................................................17
8.4 Operation....................................................................................................................................................................... 19
8.5 Notication messages...............................................................................................................................................20
9. Limited Warranty........................................................................................................................................................................21
!

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
3 4
Screen
Resolution
Video system
Audio type
Call time
Internal memory
Memory extension slot
Standby mode power consumption
Working mode power consumption
Power supply
Mounting type
Size
Working temperature
7”, color TFT
800×480 pixels
PAL/NTSC
Half duplex
120 seconds
No
microSD, up to 32 Gb
4 W
8 W
Built-in power supply, ~100–240 V
Surface mount
230×165×22 mm (9.25×6.50×0.87")
−10...+55 ˚C (+14...+131 ˚F)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Power LED. Active when power is on.
First door panel LED. Active when the rst door panel is on.
Second door panel LED. Active when the second door panel is on.
Display
«Up» button – increase talking volume, system settings menu cursor movement,
parameter increase inside settings menu
«Down» button – decrease talking volume, system settings menu cursor movement,
parameter decrease inside settings menu
Speaker (on the back side of the monitor)
«Settings» button:
• push this button in standby mode to enter system settings menu;
• push this button on chosen parameter inside system settings menu to change its
value. Then push it again to confirm the changes;
• push this button in monitoring or talking mode to enter brightnes, contrast and
color settings menu;
«Record» button – start/stop manual video recording from the door panel or camera in
monitoring or talking mode
«Monitor» button – door panel or camera image monitoring
«Answer» button – incoming call answer and start talking with the visitor
«Unlock» button – door unlocking
MicroSD memory card slot (on the side of the monitor)
«Hang Up» – stop conversation with the visitor / current system settings menu exit
Microphone
1. Package
SL-07IP door monitor − 1 pc.
Wall mounting bracket − 1 pc.
Connection wires − 5 pcs.
Mounting screws and nuts − 1 pkg.
User manual − 1 pc.
2. Specication
5
1 2 3 4
6
7
8
9
10
11
12
13
14
15
3. Description
165 mm (6.50")
230 mm (9.25") (0.87")
22
mm

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
5 6
4.2 Schematic diagrams
Diagram 1. SL-07IP door panels, cameras and locks connection.
Lock
Door panel 1
Door panel 2
Lock power
supply
Lock Lock power
supply
Camera
power
suppply
Camera
power
suppply
CCTV 1
CCTV 2
4. Installation
4.1 Cable requirements
Disconnect all power cables before device installation.
This device can be connected with such cable types depends on the distance between door monitor and
door panel:
) Use 4-wire cable with such parameters:
• distance up to 25 meters (82 ft.) use a cable with 0,22 mm square of one wire (AWG 24);
• distance 25 to 50 (82-164 ft.) meters use a cable with 0,41 mm square of one wire (AWG 21);
• distance 50 to 100 meters (164-328 ft.) use a cable with 0,75 mm square of one wire (AWG 18).
b) If the distance between door monitor and door panel is between 80 and 100 meters (262-328 ft.) then use
a 3-wire cable with 0,75 mm(AWG 18) square of one wire and RG-59 or RG-6 coaxial cable for the video
signal.
c) Shielded or non-shielded twisted pair (not recommended):
• distance up to 25 meters (82 ft.) non-shielded twisted pair can be used;
• distance 25 to 50 (82-164 ft.) meters shielded twisted pair should be used.
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
0 - 50 m
Shield
Shield
50 - 80 m
80 - 100 m
RG-59 or RG-6
Video
GND
GND
+12 V
Video
GND
GND
+12 V
Power
Audio
GND
Video
Power
Audio
GND
Video
0 - 25 m
25 - 50 m
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Power
Audio
Ground
Video
Shield Shield
Door 2
Output
CCTV 1/2
Power
Door 1
Video 2
Ground
Ground
Video 1
SL-07IP
Power
Ground
+13,5 V
*
164 - 262 ft.
0 - 164 ft.
262 - 328 ft.
0 - 82 ft.
82 - 164 ft.

Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
Door 1
Door 2
CCTV 1
CCTV 2
Input
Output
PowerTV out
{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
7 8
Diagram 2. SL-07IP system connection.
SL-07M (Slave)
Notes:
* Use «Power»plug on the monitor to connect external power supply +13,5 V. While use external power
supply please keep main power cord ~100-240 V disconnected from the outlet, otherwise it can damage
monitor circuits.
** Door panels, cameras, power supplys and locks, described on the schemes are optional devices and are
not included into monitors kit.
*** SL-07IP can only be used as a «Master» in the door phones system.
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
Audio
GND
Data
Video
SL-07M (Slave) SL-07M (Slave)
4.3 Unit mount
1) Take the surface mount bracket from the kit and place it 150-160 cm from the oor line.
2) Mark and drill four halls in the wall.
3) Take four wall anchors from the kit and hammer them into the drilled halls.
4) Fix surface mount bracket on the wall by four screws from the kit.
5) Connect all communication wires and x the monitor on the surface mount bracket.
SL-07IP (Master)
Door 2
Output
CCTV 1/2
Power
Door 1

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
9 10
5.2 Door panel and camera image view
Standby mode
Monitor will display
the image from the
rst door panel
(monitoring time – 60 seconds)
Monitor will display
the image from the
second door panel
(monitoring time – 60 seconds)
Press «Monitor»
button on the
monitor
5. Operation
5.1 Incoming call
Standby mode
Standby mode
Melody is ringing on the
monitor and door panel,
image from the door panel
appears on the monitor screen
Visitor presses call button
on the rst door panel
Visitor presses call button
on the second door panel
Press «Answer» button to start
conversation with the visitor
Melody stops ringing and
conversation starts,
talking time is 120 seconds
Press «Hang up» button to
stop conversation or
incoming call
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Notes:
1) Monitor will be automatically switched into standby mode if the user doesn’t answer incoming call
during 60 seconds;
2) Image and sound from the door panel will be active during 20 seconds after the moment user presses
button. It let the user know if the visitor passed through the door.
20 seconds
20 seconds
Standby mode
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Press «Monitor»
button on the
monitor again
Monitor will display
the image from the
rst CCTV camera
(monitoring time is unlimited)
Monitor will display
the image from the
second CCTV camera
(monitoring time is unlimited)
Press «Hang up» button to
stop monitoring or
conversation
Press «Answer» button to start
conversation with the visitor
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
11 12
5.4 Intercom
Two monitors connected into one system are used.
Melody starts
ringing on the
other monitor
Standby mode
5.3 Incoming call redirection
Two monitors connected into one system are used.
Notes:
1) If only two door panels connected to the monitor (no CCTV cameras) then you can escape monitoring
mode by pressing «Monitor» button one more time. (all other sources of video signal should be
disabled in the monitor settings).
2) If several monitors connected into one system, the user can view the image from door panels on any
monitor inside this system. The image will be transferred from the «Master» monitor door panels to the
«Slave» monitors.
3) If someone press call button on the door panel while monitoring is active then the image from this door
panel appears on the monitor screen and call melody starts. Press «Answer» button to start
conversation.
Note:
If incoming call was successfully redirected to the other monitor and other user answered the call then
current monitor will enter standby mode.
Melody starts ringing on
the other monitor inside
the system and visitor image
appears on the monitor screen
Conversation with the
visitor on the other
monitor begins
Incoming call from the
door panel and the
user starts conversation
Press and hold
«Answer» button
for 3 sec. to start
call redirection
20 seconds
Note:
If someone press call button on the door panel while intercom is active then the image from this door panel
appears on the monitor screen and call melody starts. Press «Answer» button to start conversation
with the visitor.
6. Monitor settings
6.1 Main menu
Press button in standby mode to enter main menu monitor settings. Use or buttons
to move through the settings. Press button again to enter current setting. Then press or
button to change current parameter value and approve the setting by pressing button.
Press button on the keyboard to exit from the current menu.
Main menu has following settings:
English – choose menu language;
Ringtone – choose one of 16 melodies;
Ringtone volume – incoming call volume level, from 01 to 08;
Duration of the ringtone – call melody duration time, from 05 to 30 seconds;
Unlock time – relay unlock time, from 01 to 10 seconds;
CCTV 1 and CCTV2 – include (Enable) or exclude (Disable) CCTV camera from the monitoring list.
Press «Answer» button on the
other monitor to start
conversation with the visitor
Standby mode
Press «Unlock» button to open
lock connected to the current
door panel, relay built into the
panel will open the lock
Press «Hang up» button to
stop conversation or
incoming call
Standby mode
Press «Answer»
button to start
intercom
conversation
Conversation with the
other monitor starts
Press «Answer» button on
the other monitor to start
conversation
Press «Hang up»
button to stop
conversation

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
13 14
English
Ringtone
Ringtone volume
Duration of the ringtone
Unlock time
CCTV 1
CCTV 2
Exit
01
08
30
02
Enable
Disable
Панель 1
25
Android / iOS
Internet
3G / Wi-Fi
Router
PC
WAN 1 2 3 4
SL-07IP
7. Network connection diagrams.
Diagram 1. SL-07IP wired network connection.
Diagram 2. SL-07IP wireless Wi-Fi network connection.
Android / iOS
Internet
3G / Wi-Fi
Wi-Fi (LAN)
«Access point»
mode
Router
PC
WAN 1 2 3 4
Android / iOS
SL-07IP
6.2 Display and conversation volume settings
Press button in monitoring or talking mode to enter brightnes, color, contrast and volume settings
menu. Brightness setting bar will appear on the screen. Press or buttons to increase or decrease
brightness, then press button to go to the next parameter setting in the next order:
color/contrast/volume. Every parameter value can be changed by or buttons. After volume
setting press button again to exit settings menu.

{ Design. Uniqueness. Innovations}DESIGN
DIRECT
SERIES
15 16
8. Software
Enter «Google Play»(for Android) or «Apple App Store»(for iOS) and search for «Cloud Call»application,
then install this applicationи on your mobile device.
Below you can nd basic steps how to add new device to «Cloud Call» application.
Full manual on «Cloud Call» application you can nd on www.slinex.com
8.1 Creating new account
1) Start «Cloud Call» application on your mobile device and press «NEW USER» button to create an account;
2) Fill in «Email» box and press «GET CODE» button;
3) Check for a new message with activation code on your Email account and enter it into «Verication
Code» box;
4) Fill in «Password» and «Conrm Password» boxes and press «CONFIRM» button to create new account.
That password will be used to login into created account.
8.2 Wired network connection steps
1) Use twisted pair CAT5 or CAT6 cable to connect device to the router;
2) Connect mobile device into the same local network;
3) Press «CONNECT NEW DEVICE» button, then choose «EXISTING» check box and press «CONFIRM»
button;
4) New devices search will be applied and you will see the list of the devices, connected to the local
network;
!
5) Tap on UID in the left column, corresponding to the device sticker or press «QR CodeScan» button and
then scan QR code on your device sticker if device UID isn’t in the list;
6) Fill in device information:
Device UID: unique identication number of the device (already lled);
Device Name: any name you like;
Password: 888888 (by default);
then press «CONFIRM» button and you will see added device on the main bar.

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
17 18
8.3 Wireless Wi-Fi network connection steps
1) Connect mobile device into the Wi-Fi network you want to connect the monitor;
2) Disable 3G/4G internet connection on your mobile device;
3) Press «CONNECT NEW DEVICE» button, then choose «NEW» check box and press «CONFIRM» button;
4) Enter into «Access point» mode if the monitor doesn’t enter it automatically. In «Access point» mode
monitor buttons backlight is constantly blinking. You can enter into «Access point» mode manually by
following next steps: press&hold button on the monitor until you will hear a «beep» sound,
then release button and wait for another «beep» sound after a minute. It means the monitor
restarted and entered into «Access point» mode.
5) Press «CONTINUE» button on the mobile device screen to go to the next step. In case if you add current
monitor for the second time then before pressing «CONTINUE» button forget (delete) monitor’s network
(network name begins from cctv2...) in your mobile phone or tablet Wi-Fi settings;
6) Enter password of the Wi-Fi network which you want to connect to and press «CONTINUE» button;
7) Fill in device information:
Device UID: unique identication number of the device (already lled);
Device Name: any name you like;
Password: 888888 (by default);
then press «CONFIRM» button and you will see added device on the main bar.
Notes:
1) If there is no LAN cable connected to the monitor or outdoor panel on the rst boot then it will automatically
go into «Access point» mode and you can skip 4th step of section 5.3.
2) If device is already added to some account, you can’t add it to another one, only can share it with other
account.

{ Design. Uniqueness. Innovations} DESIGN
DIRECT
SERIES
19 20
8.4 Operation
Tap on the device
image to start
monitoring
Main bar Device bar
Tap on the recycle
bin to delete
this devise from
the account
Talk with
the visitor
Hang on
Door unlock
(Default password:
888888)
Disable
monitoring
Tap on settings icon
to enter device
settings
Change default
device password
Motion detection
settings
SD card
information
Door panel/
monitor
rmware update
List of
shared
devices
Change
default
unlock
password
Time sync
with mobile
device
Default
settings/
reboot
Share
device with
other
account
8.5 Notication messages
Press button to activate notification
messages preset.
DND mode – notification messages are
disabled;
Online mode – notification messages
are enabled;
Custom mode – notification messages
can be enabled or disabled depending
on the settings inside that preset;
In case notification messages are
enabled then you wil receive push
message if somebody presses call
button on the outdoor panel.
Press «ANSWER» button to start talking
with the visitor or «CANCEL» button to
stop the call.
Take a
snapshot Record video
Speaker volume/
microphone
sensitivity
Full screen
mode
Image quality:
HD or SD
Note:
While device monitoring, one way audio is constantly active from the outdoor panel side so you can hear
what hapens nearby. To activate two way communication press «Talk with the visitor» button in the
application.
Call

{ Design. Uniqueness. Innovations } DESIGN
DIRECT
SERIES
21 22
9. Limited warranty
Manufacturer guarantees product normal functioning during the warranty period if the user keeps all safety
instructions described in that manual.
Warranty period is 12 months from the moment of the product purchasing (warranty period could be
extended up to 24 months or more, depending on the local regulations).
Warranty period allows user to make guarantee repair in cases when normal functioning of the product was
violated by the fault of manufacturer and the user haven’t oend transporting, installation and working
conditions.
This limited warranty does not cover any damage to the product that results from improper installation,
accident, abuse, misuse, natural disaster, insucient or excessive electrical supply, abnormal mechanical or
environmental conditions, or any unauthorized disassembly, repair or modication.
Warranty void in such cases:
• the product was damaged by the fault of the customer;
• the product wasn’t properly installed according reccomendations from the manual;
• the sticker on the backside of the product was broken;
• the product was not used for its intended function.
This limited warranty covers only repair, replacement, refund or credit for defective products, as provided
above. Manufacturer is not liable for, and does not cover under warranty, any damages or losses of any kind
whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with
determining the source of system problems or removing, servicing or installing products. This warranty
excludes third party software, connected equipment or stored data. Manufacturer is therefore not liable for
any losses or damage attributable to third party software, connected equipment or stored data.
In the event a product has been discontinued, manufacturer shall either repair the product, oer to replace
it with a comparable product or provide a refund at the lesser of the purchase price or the product’s current
value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder of
the original warranty term.