Sloan G2 Optima Plus Instruction sheet

Remove Control Stop Cap.
Turn off water supply at Control Stop.
Push valve Handle to relieve pressure.
Remove Outside and Inside Covers
and old Inside Parts Assembly.
Remove old Handle Assembly and
Gasket.
Install new Handle Seal and Handle
Cap to Flushometer Valve Body.
GG22OOppttiimmaaPPlluussFFlluusshhVVoolluummee
FFoorrRREESSSS-CCaannddRREESSSS-UURReettrrooffiittMMooddeellss
The Flush Volume of the Optima Plus is controlled by the Regulator in
the Flex Tube Diaphragm Kit. Regulators are identified by color.
Reference CChart
Fixture &&FFlush Regulator
Color
0.5 gpf (1.9 Lpf) Urinal Green
1.0 gpf (3.8 Lpf) Urinal Green
1.5 gpf (5.7 Lpf) Urinal Black
1.6 gpf (6.0 Lpf) Closet Green
3.5 gpf (13.2 Lpf) Closet White
4.5 gpf (17.0 Lpf) Closet White
3.5 gpf (13.2 Lpf) Urinal White
2.4 gpf (9.0 Lpf) Closet Blue
NNootteess::For a 4.5 gpf (17.0 Lpf) Water Closet flush, use the EBV-1020-A
kit with the White Regulator. Cut and remove the A-164 Flow Ring from
the Guide.
A 0.5 gpf (1.9 Lpf) Urinal kit can be converted to a 1.0 gpf (3.8 Lpf) by
cutting and removing the smooth A-164 Flow Ring from the Guide.
RESS-C and RESS-U G2 Optima Plus valves are supplied with
multiple Regulators to address multiple flushing applications. The
product is shipped with it’s lowest flush volume configuration. To
convert the flush to a higher flushing volume, simply change the
Regulator.
When installing a new Regulator on a Flex Tube Diaphragm Kit, be
sure to push the Regulator past the O-ring when Installing.
Note: Never use more water than needed. Low Consumption water
closets and urinals will not function properly on excess water.
Remove Tab.
Make sure Flush Volume Regulator is
installed past O-ring. Insert metal end
of Flex Tube Diaphragm Assembly into
hole at the base of the Sensor Module.
O-ring must be fully inserted into hole.
RESS V.I.G. — Rev. 0 (05/03)
Code No. 0816455
3
4
5
2
1
1
2
3
4
5
7
6
7
6
VVIISSUUAALLIINNSSTTAALLLLAATTIIOONNGGUUIIDDEELLIINNEESSFFOORRSSLLOOAANN
FFLLUUSSHHOOMMEETTEERRSSRREESSSSUUNNIITTIINNSSTTAALLLLAATTIIOONN
FLUSH VOLUME
REGULATOR
0-RING
0-RING
REGULATOR
(MUST BE INSTALLED
PAST 0-RING)
FLEX TUBE
DIAPHRAGM

Test Sensor by standing in front of Sensor for Ten (10) Seconds.
Step away from Sensor and listen for "CLICK."
Click
any questions
?
• We recommend that you review our G2 OPTIMA Plus Installation Instruction Manual and Maintenance Guides for
complete instructions including Rough-in Dimensions, Specifications, Troubleshooting Guide, and Replacement Parts.
• Call our Installation Engineers for additional information at 1-800-9-VALVE-9 or fax them at 1-800-737-3061.
The information contained in this document is subject to change without notice.
Test your Flushometer!
SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131
Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: [phone] or 1-847-671-4380 • http://www.sloanvalve.com
Copyright © 2003 Sloan Valve Company • Printed in the U.S.A. • Made in the U.S.A. • 0816455 — Rev. 0 (05/03)
9
16
13
15 17
11
12
Tighten with Strap Wrench. Pull Tab to activate.
Install Assembly onto
the Flushometer Valve
Body. Lens must face
directly forward.
8 10
Activate Flushometer and adjust Control Stop after each flush until rate of flow delivered
properly cleanses the fixture. The Control Stop should never be opened to the point
where the flow from the valve exceeds the flow capability of the fixture. In the event of a
valve failure, the fixture must be able to accommodate a continuous flow from the valve.
Open Control Stop (counterclockwise) ½ turn
from closed position.
Place hand over lens for 10 seconds
or press override button to activate.
Adjust Control Stop to meet the flow
rate requirement for proper cleansing
of the fixture.
Install Control Stop Cap.
14
Range adjustment is factory set
and typically does not require
adjustment.
If range adjustment is required,
refer to the Installation
Instructions furnished with the
G2 Optima Plus Flushometer.