Sloan EBV-200-A SMOOTH User manual

EBV-200-A SMOOTH FLUSHOMETER RETROFIT KIT INSTALLATION INSTRUCTIONS
Code No. 0816556
Rev. 0b (07/07)
INSTALLATION INSTRUCTIONS
(SIDE-MOUNT-OPERATOR-OVER-THE-HANDLE)
FLUSHOMETER RETROFIT KIT
1Pull and swing Mounting Clamp to the
open position.
NOTE: Water does not need to be shut off.
2Slide the unit over the existing handle up
to the flushometer body.
3Swing the Mounting Clamp around the
flushometer body and press the clamp
end into the unit until it clicks into place.
4Tighten unit by pushing in on the
spring loaded Mounting Screw and
turning clockwise with a 1/8” hex
wrench. Do Not overtighten.
5Remove Adhesive Label from sensor
window.
NOTE: Red LED light will flash and
product will cycle. Unit is now ready
for use.

2
OPERATION
NORMAL OPERATION
When a user enters the sensor's effective range,
the Red LED light in the sensor window flashes for
eight seconds. After eight seconds of sensing a
user, the light will stop flashing and the unit waits
for the user to step away before initiating a flush
cycle.
LOW BATTERY INDICATOR
A manual flush cycle may be initiated by fully
pressing and releasing the Override Handle.
INITIATING A MANUAL FLUSH CYCLE
When a user enters the sensor’s effective range
and the Red LED light in the sensor window
flashes twice as fast as normal, the batteries need
replacement. Refer to the Battery Replacement
Instructions on Page 4.

3
ADJUSTMENT PROCEDURES
RESETTING UNIT TO NORMAL RANGE
(Water Closets)
The SMOOTH unit is factory set with a Sentinel Flush Feature. This Feature will activate the flushometer once
every 72 hours with no activity, to maintain the water seal in the fixture and conserve water. There should be no
need for further adjustments; however, if an adjustment is required, refer to the following instructions.
Note: To make the adjustments indicated below, power to unit(s) must be turned off for ten (10) seconds.
Mode selection is available within one (1) hour after every power up condition (reinstalling batteries).
Mode A
The SMOOTH unit may be reset to normal range
by fully pressing and holding in the Override
Handle until the Red LED light in the Sensor
Window illuminates. Then immediately release the
Override Handle.
SETTING UNIT TO REDUCED RANGE
(Typically for Urinals)
Mode C
The SMOOTH unit may be set to reduced range by
pressing and holding in the Override Handle until
the Red LED light in the Sensor Window displays
a rapid on and off blinking light. Then immediately
release the Override Handle.
SETTING UNIT FOR REDUCED RANGE
(Water Closets)
Mode B
The SMOOTH unit may be set to reduced range
for closet applications by pressing and holding in
the Override Handle until the Red LED light in the
Sensor Window flashes a slow long blinking light.
Then immediately release the Override Handle.

Copyright © 2007 SLOAN VALVE COMPANY
Air Delights, Inc. • 11170 SW 5th St., Ste. 100, Beaverton, OR 97005
Phone: [phone] or email: [email protected]
www.airdelights.com
07-07
LIMITED WARRANTY
Sloan Valve Company warrants its OPTIMA SMOOTH™ EBV-200-A unit to be made of rst class materials, free from defects of material or workmanship
under normal use and to perform the service for which it is intended in a thoroughly reliable and ecient manner when properly installed and serviced, for
a period of three years from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove
to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available underthis warranty. No claims will
be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company’s
products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of the batteries.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
NOTICE: The information contained in this document is subject to change without notice.
If further assistance is required, please contact the Air Delights, Inc. Installation Engineering Department at:
1-800-440-5556 or email [email protected]
BATTERY REPLACEMENT INSTRUCTIONS
1Release Mounting Clamp by turning
the Mounting Screw counterclockwise
with a 1/8” hex wrench.
NOTE: Water does not need to be shut o.
2Swing the Mounting Clamp into the open
position.
3Slide the unit from the ushometer body.
4Open Battery Compartment Door and
remove old batteries from unit. Replace
batteries with 4 (four) new C-size
batteries. Close Battery Compartment
Door. Reinstall unit as instructed on front
page.
MAINTENANCE PROCEDURES