Sloan TruFlush TRF 8936-CP User manual

Code No. 08160044
Rev. 2(07/22)
INSTALLATION INSTRUCTIONS FOR
TRUFLUSH ELECTRONIC DUAL FLUSH WALL PLATE
TruFlush Model:
TRF 8936-CP
TRF 8924-CP
TRF 8924-N-CP
PRIOR TO INSTALLATION
TOOLS REQUIRED FOR INSTALLATION
• Phillips screwdriver
This valve is designed for new construction or where there is easily
accessed plumbing for the xture and the valve.
This valve is designed for minimum six inch (152 mm) wall space
depth. Distance from center of the valve (inlet or outlet pipe) to the
nished surface of the wall can vary from 2”-3” (51-76 mm).
Wall plate opening must be of 5.6” x 5.6” (142 x 142 mm). Mud plate
is provided and must accompany valve for proper installation. Mud
plate is removed after wall is nished.
ITEMS INCLUDED WITH THE PRODUCT
ITEM #1: WALL BOX AND
ELECTRONIC VALVE
ASSEMBLY
ITEM #2: MUD GUARD
ITEM #3: ACTIVATION
ASSEMBLY TOOL
ITEM #4: #8-32 X 2" TRUSS
HEAD SCREWS
ITEM #5: 1/4-20 X 2"
SCREWS
SENSOR VALVE BOX
ITEM #1: WALL BOX ITEM #2: WALL PLATE ITEM #3: SENSOR ASSEMBLY ITEM #4: ACTIVATION BUTTON ITEM #5: BATTERY PACK ITEM #6: 4X BATTERIES ITEM #7: 4X #8-32 X 2"
TRUSS HEAD SCREWS
ITEM #7: 5/64" HEX KEY
WALL PLATE BOX
ITEM #1: WALL BOX AND
ELECTRONIC VALVE
ASSEMBLY
ITEM #2: MUD GUARD
ITEM #3: ACTIVATION
ASSEMBLY TOOL
ITEM #4: #8-32 X 2" TRUSS
HEAD SCREWS
ITEM #5: 1/4-20 X 2"
SCREWS
SENSOR VALVE BOX
ITEM #1: WALL BOX ITEM #2: WALL PLATE ITEM #3: SENSOR ASSEMBLY ITEM #4: ACTIVATION BUTTON ITEM #5: BATTERY PACK ITEM #6: 4X BATTERIES ITEM #7: 4X #8-32 X 2"
TRUSS HEAD SCREWS
ITEM #7: 5/64" HEX KEY
WALL PLATE BOX
• Adjusting tool (supplied)
1. Wall Bracket
2. Wall Plate
3. Sensor Assembly
4. Battery Pack
5. (4) Batteries
6.(4) #8-32 x 2 Screws
7.Allen Key
8.Installation instructions
WALL PLATE BOX
1. Wall Bracket 2. Wall Plate 3.PCB Assembly
4. Battery Pack 5. (4) Batteries 6. (4) #8-32 x 2 Screws 7. Allen
Key
8. Instructions
• Flathead screwdriver .118”
(3 mm or below)
• Wire stripper tool
Sloan® India Private Limited - Limited Warranty Summary
Sloan India Private Limited (“Sloan”), warrants its products against defects in materials and workmanship,
excluding damage caused by matters beyond Sloan’s reasonable control. Instructions for filing claims can be
found in the Limited Warranty which can be obtained at https://www.sloan.com/company/international/sloan-
india or by requesting a free copy by telephone to Sloan India toll free number 1 800 123 3080 or via Mobile:
[phone] or via Landline : [phone]. Sloan will repair or replace your defective product, or
provide a refund, as your exclusive remedy.
This is only a general summary of Sloan’s Limited Warranty so it is important to note that the specific terms,
conditions, limitations and exclusions, including the duration of warranty coverage for your particular Sloan
product, are contained in the actual Sloan Limited Warranty. The Limited Warranty is subject to applicable
laws in your country, state, province or other jurisdiction—and disputes arising under the Limited Warranty are
to be resolved by binding arbitration unless you provide Sloan with an opt-out notice no later than 30 days
after your purchase date. In case of a conflict with this summary, the terms and conditions set forth in the
complete Limited Warranty will prevail.

1. CONNECT FLUSHOMETER
2
Refer Valve Assembly Installation Manual as per the Valve Selection Guide.
2. INSTALL WALL PLATE ASSEMBLY
-
-
+
+
+
-
3. Open the battery package (supplied) by unscrewing the lid screw, insert the
batteries (4Nos, Supplied) into the battery package as shown and close the lid by
tightening the screw.
4. Insert the battery package on right side of valve as shown.
5. Connect the battery box black connector to black connector on PCB assembly, Connect Solenoid grey connector to grey connector on PCB assembly.
NOTE: RED LED WILL START BLINKING WHEN POWER IS CONNECTED TO THE PCB ASSEMBLY, WAIT FOR THE LED TO FINISH
BLINKING.
!!! ONLY FOR HARDWIRE CONNECTION !!!
5a. Using the wire stripping tool strip, the ends of the transformer wire that was routed when installing the valve.
5b. Insert wire in blue terminal block and tighten the terminal screws.
5c. Connect the terminal block to the PCB assembly as shown.
1. Remove the mudguard by unscrewing the two screws and
discard the mudguard
2. Mount the Wall Bracket to valve and secure it using the
#8-32 x 2 Screws Screws (Supplied).

3
Snap clip
6. Align the 4 slots on the PCB Assembly with the mounting pegs on the Wall Bracket and slide the PCB assembly all the way down.
7. Disconnect the Solenoid Connector and lift the button as shown,
Use the tool to turn the activation assembly clockwise
(to lessen the flow) or anticlockwise (to increases the flow).
8. Reconnect the solenoid and check the flow by flushing, repeat
step 7 to adjust the flow until the flow
rate delivered properly cleanse the
fixture.
THE FLUSHOMETER IS ENGINEERED FOR QUIET OPERATION.
EXCESSIVE WATER FLOW CREATES NOISE, WHILE TOO
LITTLE WATER FLOW MAY NOT SATISFY THE NEEDS OF THE
FIXTURE. PROPER ADJUSTMENT IS MADE WHEN PLUMBING
FIXTURE IS CLEANSED AFTER EACH FLUSH WITHOUT
SPLASHING WATER OUT FROM THE LIP AND A QUIET
FLUSHING CYCLE IS ACHIEVED.
!!! IMPORTANT !!!
THE ACTIVATION ASSEMBLY SHOULD NEVER BE OPENED TO
THE POINT WHERE THE FLOW FROM THE VALVE EXCEEDS
THE FLOW CAPABILITY OF THE FIXTURE. IN THE EVENT
OF A VALVE FAILURE, THE FIXTURE MUST BE ABLE TO
ACCOMMODATE A CONTINUOUS FLOW FROM THE VALVE.
!!! IMPORTANT !!!
UNDER NO CIRCUMSTANCES SHOULD THE SOLENOID BE
REMOVED OR ADJUSTED.
!!! NOTE !!!
MAKE SURE FLUSHOMETER SOLENOID CONNECTOR IS
DISCONNECTED FROM SENSOR ASSEMBLY EVERY TIME
BEFORE ROTATING ACTIVATION ASSEMBLY.
!!! NOTE !!!
MAKE SURE SOLENOID CONNECTOR GOES THROUGH THE
CENTER OF THE ADJUSTING TOOL TO AVOID DAMAGE TO THE
CABLE.
!!! NOTE !!!
9. Make sure the retaining screw is fully tightened, slide the PCB assembly all the way
up and align the wall plate cutout with PCB assembly as shown.
10. Push the wall plate all the way in then slide the wall plate down.
11. Use the allen key (supplied) to unscrew the retaining screw until it touches the wall
plate then make sure the wall plate is completed fixed.
NOTE: DO NOT UNSCREW ANYMORE ONCE THE RETAINING SCREW
TOUCHES WALL PLATE

4
For complete listing of items available for repair, please consult Maintenance and Repair Guide.
available on www.sloan.in
© 2022SLOAN
Code No. 08160044
Rev. 2(07/22)
Manufactured by Sloan India Pvt. Ltd, patents pending.
SLOAN INDIA PRIVATE LIMITED
344, PHASE-II UDYOG VIHAR, GURGAON 122015 Phone: [phone]
Toll Free: 1800.123.3080 | [e-mail] | sloan.in | copyright © 2021 Sloan All rights reserved
CARE AND CLEANING
DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean Flushometers that may dull the luster and attack the chrome or special
decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Flushometer from
any splattering of cleaner. Acids and cleaning fluids will discolor or remove chrome plating.
VALVE ASSEMBLY LESS PLATE SELECTION GUIDE
Code No. Part No. Description
34001003
TRF 8036
*“Part No.”-N Refers to Valve Assembly For 32mm Plumbings.
TRF8036 Dual Flush 3/6 LPF Valve
34001011
TRF 8024-N*TRF8024-N HI EFFI (4 -4.5/2 -2.5 LPF)
34001012
TRF 8036-N* TRF8036 Dual Flush 3/6 LPF Valve
Valve Assembly Installation Manual, available on www.sloan.in
34001015
TRF 8024 TRF8024 HI EFFI (4 -4.5/2 -2.5 LPF)