SMART-AVI DVX-PLUS User manual

DVI-D and USB Extender
via Twisted Pair
EXTEND USB 1.1 AND DVI-D
BEYOND THE LIMIT -
ALL THE WAY UP TO 225FT.
USING STANDARD
TWISTED PAIR CABLE
Quick Start Guide
VIDEO
Video Interface DVI-D
Single Link Range 480P,720i/p, 1080i/p
Video Data Rate 1.65 Gbps
Resolution 1920 x 1200 @ 60 Hz, Resolution
up to 1280 x 1024 min. 75H
USB
USB max data rate 12Mbps
USB compatibility 1.0 and 1.1
Connector Type Type A (Transmitter)
Type B (Receiver)
OTHER
Power Universal Switch mode PSU
(90-240V Input) 5VDC 2A
Operating Temp. 0-55 °C (32-131°F)
Storage Temp. -20-85 °C (-4-185 °F)
Humidity Up to 95%
NOTICE
The information contained in this document is
subject to change without notice. SmartAVI makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
SmartAVI will not be liable for errors contained
herein or for incidental or consequential damages in
connection with the furnishing, performance or use of
this material.
No part of this document may be photocopied,
reproduced, or translated into another language
without prior written consent from SmartAVI
Technologies, Inc.
800.AVI.2131, 702.800.0005
2455 W Cheyenne Ave, Suite 112
North Las Vegas, NV 89032
SmartAVI.com
TECHNICAL SPECIFICATION
DVX-PLUS
WHAT’S IN THE BOX
PART NO. Q-TY DESCRIPTION
DVXU-TX 1 DVI-D and USB Transmitter
DVXU-RX 1 DVI-D and USB Receiver
PS5VD2A-WMT 2 PS5VD2A Power Supply
Quick Start Guide 1

OVERVIEW
DVX Plus extends Universal Serial Bus (USB 1.1) and Digital
Visual Interface (DVI-D) signals via common twisted pair
cable. Using a unique method of transparent data transfer,
the system allows a USB peripheral and a DVI display to be
located up to 225 feet from the CPU.
FEATURES
• Extends USB and DVI signals up to 225 from the
computer
• Uses easy to install, inexpensive twisted pair cable
• Data recovery for digital video
• Supports 1920x1200 digital video resoluon
• Fully compliant with USB 1.1 specicaons
• Supports 1.5 and 12 Mbps data rates
• Compable with all operang systems
• External power adapter for transmier and
receiver unit
• Fully transparent (does not use any emulaon)
• Plug and play
1. Connect the transmitter to the host using an A-B USB cable
2. Connect the transmitter to the host DVI-D using male to male DVI cable
3. The A side of the USB connector would go to the computer host and the B side would be connected to the transmitter
4. Check that power LED is lit. The TX/RX LED should not be ashing at this time
5. In the back of the unit connect the CAT5 cable that will connect to the receiver (DVXU-RX)
6. Connect the receiver to the peripheral device using A-B USB cable. In this case the A side of the connector will go to the
receiver unit and the B side of the connector will go the peripheral. Use a USB Hub if needed
7. Connect the receiver unit to the monitor
8. Join the DVX Plus units using shielded cable for DVI-D and standard CAT5/6 UTP cable for USB. Once connected check
that the Power LED on both receiver and transmitter is on and the TX/RX LED is ashing, indicating that communication
exists between the two units. If receiver LED is not on, make sure the power supply is connected
HARDWARE INSTALLATION
DVI IN
DVI OUT
USB IN
USB K/M OUT
USB 2.0 OUT
FIBER (VIDEO)
FIBER (USB)
225 ft
DVX-PLUS-TX DVX-PLUS-RX