Smartgen HGM6110 User manual

HGM6110/6120
Automatic Generator Module
OPERATING MANUAL
Smartgen Electronics

Smartgen Electronic Equipment Co,.Ltd
No.12 Dongqing Street
Zhengzhou
Henan Province
P.R.China
Tel : [phone] 67991572
Fax: [phone]
Web: http://www.smartgen.com.cn
http://www.smartgen.cn
Email: [email protected]
All rights reserved. No part of this publication may be reproduced in any material
form (including photocopying or storing in any medium by electronic means or
other) without the written permission of the copyright holder.
Applications for the copyright holder’s written permission to reproduce any part of
this publication should be addressed to Smartgen Electronics at the address
above.
Any reference to trademarked product names used within this publication is
owned by their respective companies.
Smartgen Electronics reserves the right to change the contents of this document
without prior notice.
Software Version
Version Date Note
1.0 2008-01-20 Original release.
1.1 2008-03-25 Amend picture error
2.0 2008-10-27 Add control

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 3 of 24
CONTENT
1.SUMMARY .....................................................................................4
2.PERFORMANCE AND CHARACTERISTICS.................................4
3.SPECIFICATION.............................................................................6
4.OPERATION...................................................................................6
4.1KEY FUNCTION........................................................................................ 6
4.2AUTOMATIC OPERATION ........................................................................ 7
4.3MANUAL OPERATION.............................................................................. 8
5.PROTECTION................................................................................9
6.CONNECTING TERMINAL...........................................................12
7.PARAMETER RANGE AND DEFINE............................................14
7.1PARAMETERS TABLE (TABLE 1)........................................................... 14
7.2OUTPUT 1-4 TABLE (TABLE 2)............................................................... 17
7.3DIGIT INPUT 1-2 TABLE (TABLE 3)........................................................ 17
7.4SENSOR (TABLE 4) ................................................................................ 18
7.5CONDITION OF CRANK SUCCEED (TABLE 5) ..................................... 19
8.SETTING PARAMETER ...............................................................19
9.TEST RUN....................................................................................21
10.TYPICAL WIRING DIAGRAM.....................................................22
11.INSTALLATION...........................................................................23
12.FAULT FINDING.........................................................................24

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 4 of 24
1. SUMMARY
HGM6100 Series generator controller integrating digital, intelligent and network
techniques is used for automatic control system of diesel generator. It can carry
out functions including automatic start/stop, data measure and alarming. The
controller uses LCD display, optional Chinese and English display interface with
operation easy and reliable.
HGM6100 Series generator controller uses micro-processing technique which
can carry out precision measure, constant value adjustment, timing and threshold
setting and etc. of multi-parameters. It can be widely used in all types of generator
automatic control system for compact structure, advanced circuits, simple
connections and high reliability.
2. PERFORMANCE AND CHARACTERISTICS
HGM6100 controller has two types:◆
HGM6110: ASM (Automatic Start Module)
HGM6120: AMF (Automatic Mains Failure Module)
Using microprocessor as a core, graphics LCD with big screen and backlight,◆
display between Chinese and English, key touch for operation.
Have a RS485 port, can used for communicat◆e to PC.
Precision measure and display of◆
mains voltage
mains frequency (Hz)
mains current
generator voltage
generator current
generator frequency (Hz)
generator active power (kW)
generator inactive power (kVar)
generator apparent power (kVA)
generator power factor
generator starts count
generator hours count
generator cumulate electric energy (kWh)
generator temperature
generator pressure
generator fuel level
start battery voltage
Configurable single phase 2 wires or 2 phase 3 wires or 3 phase 4 wi◆res AC

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 5 of 24
system input;
Control protection: Automatic start/stop, load transfer and alarming of◆
generator;
Parameters setting: Allow user to modify setting and store them inside internal◆
FLASH memory, the parameters can not be lost even with power down. All
parameters can be set from the front panel, or be set by PC used SG72
Three channel analog inputs, may joint with Resistive◆-type temperature/
pressure/ fuel level sensors, Several temperature and pressure sensors can
be used directly (ie. VDO, DATCON, CUMMINS), also may select “user
defined” sensor via entering 8 point curves;
Display of generator cumulated electric energy;◆
Security◆password-protected programming levels.
Several crank success conditions are optional;◆
Built◆-in speed/frequency detecting units can accurately judge the states such
as crank success and over speed;
Power supply range is wide, accommodating to different starting battery◆
voltage environments;
All parameters use digital modulation, abandoning analog modulati◆on using
conventional electronic potentiometer, reliability and stability are increased;
Built◆-in watch dog can never be dead halt, ensuring smooth program
execution;
Modular configuration design, inserted type connection terminals, flush type◆
installation, compact structure, easy installation.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 6 of 24
3. SPECIFICATION
Operating Voltage DC8. 0V to 35. 0V, Continuous Power Supply
Power Consumption <3W
Alternator Input Range
3-Phase 4 Wire
2-Phase 3 Wire
Single phase 2 wire
15V AC - 360 V AC (ph-N)
15V AC - 360 V AC (ph-N)
15V AC - 360 V AC (ph-N)
Alternator Input Frequency 50Hz - 60 Hz at rated engine speed
Magnetic Input Range +/- 0. 5 V to 70 V Peak
Magnetic Input Frequency 10,000 Hz (max) at rated engine speed.
Start Relay Output 7 Amp DC at supply voltage.
Fuel Relay Output 7 Amp DC at supply voltage.
Auxiliary Relay Output (1-4) （1）7 Amp DC at supply voltage，（2）
7A250VAC free
voltage contact，（3,4）16A250VAC free voltage contact.
Dimensions 200mm x 144mm x 50mm
Panel cutout 184mm x 139mm
Operating Temperature Range -25 to +70°C
Storage Condition Temperature: (-30 - 80)°C
C. T. Burden 2. 5VA
C. T. Secondary 5A
Weight 0. 55kg
4. OPERATION
4.1 KEY FUNCTION
Stop/ Reset key
This button places the module into its Stop/reset mode.
When engine is running, pressing this key will stop the
engine.When a shutdown alarm occur, pressing thiskey will
reset alarm. In stop mode, pressing this key over 3 second
will test LED mounted on the panel.
Start key In manual or manual test mode, pressing this key will start
engine.
Manual mode key Pressing this key will set the module into manual mode.
Auto key Pressing this key will set the module into automatic mode.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 7 of 24
Manual test mode Pressing this key will set the module into manual test mode.,
when generate electricity is normal, the generator will
on-load(HGM6110 have not this key)
Set/enter Enter the set menu, or validate the setting
Page up
/increase Page up, or In setting parameter status, pressing this key will increase setting value.
Page down
/decrease Page down, or In setting parameter status, pressing this key will decrease setting value.
4.2 AUTOMATIC OPERATION
The following description details the sequences followed by a module containing
the standard ‘factory configuration’. Always refer to your configuration source for
the exact sequences and timers observed by any particular module in the field.
This mode is activated by pressing the pushbutton. An LED indicator beside
the button confirms this action.
When a Remote Start signal is applied to the remote start input (Hgm6110) or
when mains voltage occur over-voltage, under-voltage, miss phasic (Hgm6120),
the following sequence is initiated:
To allow for false signals the mains abnormal timer is initiated (only Hgm6120),
Then the Start Delay timer is initiated. After this delay, if the pre-heat output
option is selected then the pre-heat timer is initiated, and the corresponding
auxiliary output (if configured) will energize.
NOTE: If the Remote Start signal is removed(Hgm6110) during the Start Delay
timer, or if mains voltage is normal (Hgm6120) during the mains abnormal timer,
the unit will return to a stand-by state.
After the above delays the Fuel Solenoid is energized, then one second later, the
Starter Motor is engaged. The engine is cranked for a pre-set time period. If the
engine fails to fire during this cranking attempt then the starter motor is
disengaged for the pre-set rest period. Should this sequence continue beyond the
set number of attempts, the start sequence will be terminated and Failed to start
alarm will be displayed on the LCD screen.
When the engine fires, the starter motor is disengaged and locked out at a pre-set
frequency from the Alternator output. Alternatively a Magnetic Pickup mounted on
the flywheel housing can be used for speed detection (This is selected by PC
using the 6100 series configuration software or form from the front panel). Rising
oil pressure can also be used to disconnect the starter motor.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 8 of 24
After the starter motor has disengaged, the Safety On timer is activated, allowing
Oil Pressure, High Engine Temperature, Under-speed, Charge Fail and any
delayed Auxiliary fault inputs to stabilize without triggering the fault.
Once the engine is running, the Warm Up timer, if selected is initiated, allowing
the engine to stabilize before accepting the load.
If an auxiliary output has been selected to give a load transfer signal, this would
then activate.
NOTE: A load transfer will not be initiated until the Oil Pressure has risen. Thus
preventing excessive wear on the engine.
On removal of the Remote Start signal, the Stop delay timer is initiated, once it
has timed out, the load Transfer signal is de-energized, removing the load. The
Cooling timer is then initiated, allowing the engine a cooling down period off load
before shutting down. Once the Cooling timer expires the Fuel Solenoid is
de-energized, bringing the generator to a stop.
4.3 MANUAL OPERATION
●HGM6120: This manual mode is activated by pressing the pushbutton.
This manual test mode is activated by pressing the pushbutton. An LED
indicator beside the button confirms this action. In any of the two mode, pressing
the pushbutton will initiate the start sequence.
If the pre-heat output option is selected this timer is then initiated, and the
auxiliary output selected is energized.
After the above delay the Fuel Solenoid is energized, then the Starter Motor is
engaged.
The engine is cranked for a pre-set time period. If the engine fails to fire during
this cranking attempt then the starter motor is disengaged for the pre-set rest
period. Should this sequence continue beyond the set number of attempts, the
start sequence will be terminated and Failed to start alarm will be displayed on
the LCD screen.
When the engine fires, the starter motor is disengaged and locked out at a pre-set
frequency from the Alternator output. Alternatively a Magnetic Pickup mounted on
the flywheel housing can be used for speed detection (This is selected by PC
using the 6100 series configuration software, or form from the front panel). Rising
oil pressure can also be used to disconnect the starter motor.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 9 of 24
After the starter motor has disengaged, the Safety On timer is activated, allowing
Oil Pressure, High Engine Temperature, Under-speed, Charge Fail and any
delayed Auxiliary fault inputs to stabilize without triggering the fault.
Once the engine is running, the Warm Up timer, if selected is initiated, allowing
the engine to stabilize before it can be loaded.
In manual mode, generator take load or no load depend on mains supply, if
mains is normal, it will not take load, otherwise it will take load.
In manual test mode, generator will take load regardless of mains supply normal
or abnormal.
●Hgm6110: This manual mode is activated by pressing the pushbutton. An
LED indicator beside the button confirms this action. In any of the two modes,
pressing the pushbutton will initiate the start sequence.
The start sequence is similar as the above.
In above process, when the Warm Up timer has expired, if the remote start signal
is active, generator will take load, if inactive, generator will not take load.
In above process, pressing key will bring the generator to a stop.
5. PROTECTION
5.1 WARN
Warns are non-critical alarm conditions and do not affect the operation of the
generator system, they serve to draw the operators attention to an undesirable
condition.
In the event of a warn, the module will display at the last screen of LCD.
Warn is shown as the below:
HIGH ENGINE TEMPERATURE: if the module detects that the engine coolant
temperature has exceeded the high engine temperature setting level after the
Safety On timer has expired and the input of Inhibit WTH stop is activated, a
warn will occur.
LOW OIL PRESSURE, if the module detects that the engine oil pressure has

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 10 of 24
fallen below the low oil pressure setting level after the Safety On timer has expired
and the input of Inhibit OPL stop is activated, a warning will occur.
LOSS OF SPEED SIGNAL, if the speed sensing signal is lost, a warning will occur
and the Lost speed delay set to zero, a warning will occur.
GENERATOR OVER CURRENT, if the module detects a generator output current
in excess of the setting and the Over current delay set to zero, a warning is
initiated.
FAIL TO STOP, If the module detects the engine is still running when the ‘Fail to
stop timer’ expires, a warning is initiated.
BATTERY HIGH VOLTAGE, if the module detects that the plant DC supply has
risen above the high volts setting level, a warning is initiated.
BATTERY LOW VOLTAGE, if the module detects that the plant DC supply has
fallen below the low volts setting level, a warning is initiated.
AUXILIARY INPUTS, if an auxiliary input has been configured as a warning the
appropriate information will be displayed.
Low level warn, if the module detects that the engine oil level has fallen below
the low level setting level has expired, a warning will occur.
Failed to charge warn, if the module detects that the charge of volts has fallen
below the setting level has expired, a warning will occur.
5.2 Shutdown alarm
Shutdowns are latching and stop the Generator. The alarm must be cleared, and
the fault removed to reset the module.
NOTE : The ala r m condition must be rect ified before a reset will take place. If
the alarm condition remains it wil l not be possible to reset the unit (The
except i on to this i s the Low Oil Pressure alarm, as the oil pressure will be
low with t he engine at rest).
EMERGENCY STOP, removal of the +ve DC Supply from the Emergency Stop
input initiates the following sequence, firstly it will initiate a controlled shutdown of
the Generator and prevent any attempt to restart the Generator until the
Emergency Stop push-button has been reset. Secondly it removes the +ve DC
supply from both the Fuel Solenoid and Starter Solenoid.
HIGH ENGINE TEMPERATURE if the module detects that the engine coolant
temperature has exceeded the high engine temperature setting level after the
Safety On timer has expired, a shutdown will occur.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 11 of 24
LOW OIL PRESSURE, if the module detects that the engine oil pressure has
fallen below the low oil pressure setting level after the Safety On timer has
expired, a shutdown will occur.
OVERSPEED, if the engine speed exceeds the setting value a shutdown is
initiated.
UNDERSPEED, if the engine speed falls below the setting value after the Safety
On timer has expired, a shutdown is initiated.
LOSS OF SPEED SIGNAL, if the speed sensing signal is lost, a shutdown is
initiated.
GENERATOR OVER FREQUENCY if the module detects a generator output
frequency in excess of the setting value a shutdown is initiated.
GENERATOR UNDER FREQUENCY, if the module detects a generator output
frequency below the setting value after the Safety On timer has expired, a
shutdown is initiated.
GENERATOR OVER VOLTAGE if the module detects a generator output voltage
in excess of the setting value a shutdown is initiated.
GENERATOR UNDER VOLTAGE if the module detects a generator output
voltage below the setting value after the Safety On timer has expired, a shutdown
is initiated.
GENERATOR OVER CURRENT, if the module detects a generator output current
in excess of the setting value is initiated, a shutdown is initiated.
FAIL TO START, if the engine does not fire after the pre-set number of attempts
has been made a shutdown will be initiated.
AUXILIARY INPUTS, if an auxiliary input has been configured as a shutdown the
appropriate information will be displayed.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 12 of 24
6. CONNECTING TERMINAL
Pin Function Dim Description
1 DC Plant Supply Input
(-ve) 2. 5mm
System DC negative input.
(Battery Negative).
2 DC Plant Supply Input
(+ve) 2. 5mm
System DC positive input.
(Battery Positive).(Recommended
Maximum Fuse 20A)
3 Emergency Stop Input 2. 5mm
Plant Supply +ve. Also supplies fuel &
start outputs.
(Recommended Maximum Fuse 32A)
4 Fuel relay Output 2. 5mm
Plant Supply +ve from pin 3.
7 Amp rated.
5 Start relay Output 2. 5mm
Plant Supply +ve from pin 3.
7 Amp rated.
6 Auxiliary Output relay 1 1.5mm
Plant Supply +ve from
pin 2.
7 Amp rated.
7
8
9 Auxiliary Output relay 2 1.5mm
Free voltage contacts.
7 Amp rated
10
11 Auxiliary Output relay 3 2.5mm
12
13 Auxiliary Output relay 4 2.5mm
Free voltage contacts.
16 Amp rated
Reference
table 2
14 Charge fail / excite 1.0mm Do not connect to ground (battery –ve)
15 Magnetic pickup +ve
16 Magnetic pickup -ve Connect to Magnetic Pickup device

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 13 of 24
Pin Function Dim Description
17 Coolant Temperature
Input Connect to Coolant Temperature
sender
18 Oil Pressure Input Connect to Oil pressure sender
19 Fuel Level input Connect to Fuel Level sender
Reference
table 4
20 Auxiliary input 1 1.0mm Switch to -ve
21 Auxiliary input 2 1.0mm Switch to -ve Reference
table 3
22 Remote start input 1.0mm Switch to -ve
23 CT Secondary for L1 2. 5mm
Connect to secondary of L1
monitoring CT
24 CT Secondary for L2 2. 5mm
Connect to secondary of L2
monitoring CT
25 CT Secondary for L3 2. 5mm
Connect to secondary of L3
monitoring CT
26 CT secondary common 2. 5mm
Connect to secondary of all
monitoring CT’s
27 Generator L1 voltage
monitoring 1. 0mm
Connect to Generator L1 output
(Recommend 2A fuse)
28 Generator L2 voltage
monitoring 1. 0mm
Connect to Generator L2 output
(Recommend 2A fuse)
29 Generator L3 voltage
monitoring 1. 0mm
Connect to Generator L3 output (
(Recommend 2A fuse)
30 Generator Neutral input 1. 0mm
Connect to Generator Neutral
terminal (AC)
31 Mains L1 voltage
monitoring 1. 0mm
Connect to mains L1 output
(Recommend 2A fuse)
32 Mains L2 voltage
monitoring 1. 0mm
Connect to mains L2 output
(Recommend 2A fuse)
33 Mains L3 voltage
monitoring 1. 0mm
Connect to mains L3 output
(Recommend 2A fuse)
34 Mains Neutral input 1. 0mm Connect to mains Neutral terminal
35 RS485 port Common 0. 5mm
36 RS485 port A(-) 0. 5mm
37 RS485 port B(+) 0. 5mm
Use only 120Ω RS485 approved
cable
Note:
1. These terminals of 31, 32, 33, 34 are not used for HGM6110 module.
2. The terminal of LINK on the rear panel is an interface for upgrading module software.
3. Sensor sensing input. Connect to resistive type sender.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 14 of 24
7. PARAMETER RANGE AND DEFINE
All parameters of HGM6100 as follows:
7.1 PARAMETERS TABLE (TABLE 1)
Num Parameter Range Default Remark
1 Mains normal delay (0-3600)S 10
2 Mains abnormal
delay (0-3600)S 5 Mains transient delay, suited for
ATS(automatic transfer switch)
3 Mains under volt (30-360)V 184
When mains voltage is under than
the point, mains under voltage is
active. When the point is zero,
mains under voltage is disabled.
4 Mains over volt (30-360)V 276
When mains voltage is over than the
point, mains over voltage is active.
When the point is 360V, mains over
voltage is disabled.
5 Transfer rest time (0-99.9S) 1.0
It’s the delay from mains is opened
to generator closing or from
generator is opened to mains
closing.
6 Start delay (0-3600s) 1 It’s the delay from remote start signal is active or mains is failure, to
start generator.
7 Stop delay (0-3600s) 1 It’s the delay from remote start signal is inactive or mains is normal,
to stop generator.
8 Number of Crank (1-10)次3 Numbers of crank cycles.
9 Preheat time (0-300)S 0
10 Cranking time (3-60)S 5
11 Crank rest time (3-60)S 10
12 Safe time (1-60)S 10
13 Start idle time (0-3600)S 0
14 Warming up time (3-3600)S 10
15 Cooling time (3-3600)S 10
16 Stop idle time (0-3600)S 0
17 ETS solenoid hold (0-120)S 20 It’s the delay for energizing to stop.
18 Fail to stop delay (0-120)S 0
19 ATS close time (0-10)S 5.0 Mains or Generator switch closing pulse width, when it is zero, output
is continuous.
20 Flywheel teeth (10-300) 118
21 Gens Volt Abnorm
Time 0-20.0S 10.0

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 15 of 24
Num Parameter Range Default Remark
22 Gens over volt (30-360)V 264
When generator voltage is over than
the point, generator over voltage is
active. When the point is 360V,
generator over voltage is disabled.
23 Gens under volt (30-360)V 196
When generator voltage is under
than the point, generator under
voltage is active. When the point is
30V, generator under voltage is
disabled.
24 Under speed (0-6000)RPM 1200
When the engine speed is under
than the point and hold great than
10 seconds, generator under speed
is active.
25 Over speed (0-6000)RPM 1710
When the engine speed is over than
the point and hold great than 2
seconds, generator over speed is
active.
26 Gens under freq 0-75.0Hz 45.0
When generator frequency is low
than the point, generator low
frequency and hold great than 10
seconds is active.
27 Gens over freq 0-75.0Hz 57.0
When generator frequency is over
than the point and hold great than 2
seconds, generator over frequency
is active.
28 High temperature (80-140)℃98
When engine temperature sensor
value is large than this point and
remain for 2 seconds, send out
shutdown alarm. When the value is
140, send out warning alarm. (It’s
suited for engine temperature
sensor only).
29 Low oil pressure (0-400)kPa 103
When engine oil pressure sensor
value is less than this point and
remain for 2 seconds, send out
shutdown alarm. When the value is
zero, send out warning alarm. (it’s
suited for oil pressure sensor only)
30 Low fuel level (0-100)% 10 When fuel level sensor value is less than this point and remain for 10
seconds, send out warning alarm.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 16 of 24
Num Parameter Range Default Remark
31 Lost speed delay 0-20.0S 5.0
When speed is zero and remain for
the delay, send out shutdown alarm.
When the delay is zero, send out
warning alarm.
32 Charge fail volt (0-30)V 6.0
During generator is running, when
charge alternator WL/D+ voltage is
low than this point and remain for 5
seconds, generator will warning
alarm.
33 Battery over volt (12-40V) 33.0
When generator battery voltage is
over than the point and hold for 20
seconds, battery over voltage signal
is active. It’s a warning alarm.
34 Battery under volt (4-30V) 8.0
When generator battery voltage is
less than the point and hold for 20
seconds, battery under voltage
signal is active. It’s a warning alarm.
35 CT rate (5-6000)/5 500 Current transformer rate
36 Full load current (5-6000)A 500 Mains or generator set maximum
rated current.
37 Over current (50-130)% 120 When the load current is over than the point, the over current delay is
initiated.
38 Over current delay (0-3600)S 1296
When load current is over than the
point and hold great than the timer,
send out over current signal. When
the delay is zero, over current is
disabled.
39 output1 set (0-9) 2 Energized to stop
40 Output2 set (0-9) 3 Idle control
41 Output3 set (0-9) 5 Close gens
42 Output4 set (0-9) 6 Close mains
43 Digit input1 set (1-16) 1 High Temperature input
44 Digit input1 delay 0-20.0S 2.0
45 Digit input2 set (1-16) 2 Low Oil Pressure input
46 Digit input2 delay 0-20.0S 2.0
47 Passwords set (0-9999) 1234
48 Crank disconnect (0-5) 2 Setting Item Is Given in Table 5.
49 Speed disconnect (0-3000)RPM 360 When engine speed is large than
this point, starter will disconnect.
50 Freq disconnect (10-30)Hz 14 When generator frequency is large than this point, starter will
disconnect.

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 17 of 24
Num Parameter Range Default Remark
51 OP disconnect (0-400)kPa 200 When engine oil pressure is large than this point, starter will
disconnect.
52 SelectAC system 0 3P4L 1 2P3L
2 1P2L 0 3P4L(3 phase 4 wire)
53 Select temp curve (0-8) 04 SGD(120 )℃
54 Select press curve (0-8) 04 SGD(10Bar)
55 Select level curve (0-5) 0 Not used
7.2 OUTPUT 1-4 TABLE (TABLE 2)
Num Content Description
0 Not used
1 Common alarm The designated programmable output relay will energize when any warning or shutdown fault
circuit has been activated.
2 Energised to stop
The designated programmable output relay will
energize when a stop signal has been activated.
The output will remain energized for pre-set timer
once the engine has come to a complete stop, then
de-energizes.
3 Idle control
The designated programmable output relay will
energize when the idle delay is not zero. The
output contact would typically be connected to the
“idle/run” input control of an electronic governor.
4 Preheat control
The designated programmable output relay will
energize during the preheat delay timer period and
also energize until the engine receive a crank
success signal. The preheat output is typically
used for an engine starting aid such as glow plugs.
5 Close Gens Switch generator breaker on.
6 Close mains Switch mains breaker on.(HGM6120)
7 Open ATS Switch breaker off. The output delay is 3 seconds.
8 Raise speed control It’s active from entering warming to switching load
on.
9 Drop speed control It’s active from idling in stopping to engine has
been stopped.
10 Reserve
7.3 DIGIT INPUT 1-2 TABLE (TABLE 3)
Num Content Description
0 Not used

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 18 of 24
Num Content Description
1 high Temp input High engine temperature digital input
2 Low OP input Low oil pressure digit input
3 Auxiliary warn Auxiliary warn alarm digital input.
4 Auxiliary shutdown When power on, if active, generator will stop
immediately.
5 Stop after cooled
During engine running, if the engine occur high
temperature shutdown, when the input is active, the
engine will first initiate cooling delay and then stop,
else will stop immediately.
6 Gen closed input The input state of generator closed.
7 Mains closed input The input state of Mains closed.
8 Inhibit WTH STOP When it is active, during engine running, if the engine occur high temperature, the engine will only send out
high temperature warning alarm, not stop.
9 Inhibit OPL STOP When it is active, during engine running, if the engine occur low oil pressure, the engine will only send out
low oil pressure warning alarm, not stop.
10 Reserve
7.4 SENSOR (TABLE 4)
Num Item Content Remark
1 Temperature
Sensor
0 Not used
1 Defined curve
2 VDO
3 SGH
4 SGD
5 CURTIS
6 DATCON
7 Reserve
8 Reserve
Defined curve input resistance
range is 0-
999.9 ohm, Default
is SGD
2 Oil pressure
Sensor
0 Not used
1 Defined curve
2 VDO 10Bar
3 SGH
4 SGD
5 CURTIS
6 DATCON 10Bar
7 Reserve
8 Reserve
Defined curve input resistance
range is 0-
999.9 ohm, Default
is SGD

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 19 of 24
Num Item Content Remark
3 Level
Sensor
0 Not used
1 Defined curve
2 SGH
3 SGD
4 Reserve
5 Reserve
Defined curve input resistance
range is 0-
999.9 ohm, Default
is Not used
7.5 CONDITION OF CRANK SUCCEED (TABLE 5)
Num Content
0 Speed
1 Frequency
2 Speed＋Frequency
3 Speed + Oil pressure
4 Frequency + Oil pressure
5 Frequency＋Speed + Oil pressure
8. SETTING PARAMETER
After the controller is powered up, press the key to enter into the setting
interface:1 Set Parameters
2 Information
3 Set Language/语言
uSet parameters
The default password is “1234” when it leaves factory. The senior
setting password is fixed as “0318”. When setting each item, after
selecting this item, press the key to enter the setting interface,
then press the key or to adjust the numerical value, press
the key to move the cursor, finally press the key to confirm
the set parameter.
NOTE:
a．Please set parameters in stop mode, else shutdown or other

HGM6110/6120 AUTO START MODULE
HGM6110/6120 Auto Start Module ISSUE 2.0 2008-10-27 Page 20 of 24
event may occur.
b．The over value point must be great than the under value.
c．The configurable output 1 to 4 allow to set as same item.
uInformation
LCD will display the controller software version, issue date. Note:
press the key will display the states of configurable input 1, 2
and all outputs.
uSet language
User may set display interface language as Chinese or English.
﹡Hint: Press the key will exit at any time.
Note :Sensor config
1. If the used sensor curve is not same as the standard curve, please adjust
in “Sensor curve”.
2. When entering the sensor curve, X value (voltage or resistance) must be
from small value to big value.
3. If the oil pressure sensor is not exist and the oil pressure alarm switch is
exist, please set “Oil pressure sensor” as “not used”, else low oil pressure
shutdown will occur.
4. If the sensor curve slope is positive, please according to the below curve
Diagram
Common units conversion table
1N/m2 (pa) 1kgf/cm21bar (1b/in2) psi
1Pa 1 1.01972×10-5 1×10-5 1.45038×10-4
1kgf/cm2 9.80665×1041 0.980665 14.2233
1bar 1×1051.01972 1 14.5038
1psi 6.89476×1037.0307×10-2 6.89476×10-2 1