Smartgen CMM366-3G User manual

CMM366-3G
CLOUD MONITORING COMMUNICATION MODULE
USER MANUAL
SMARTGEN (ZHENGZHOU) TECHNOLOGY CO., LTD.

Chinese trademark
English trademark
SmartGen —make your generator smart
SmartGen Technology Co., Ltd.
No.28 Jinsuo Road
Zhengzhou
Henan Province
P. R. China
Tel: [phone]
0086-371-67991553/67992951
0086-371-67981000(overseas)
Fax: [phone]
Web: http://www.smartgen.com.cn
http://www.smartgen.cn
Email: [e-mail]
All rights reserved. No part of this publication may be reproduced in any material form (including
photocopying or storing in any medium by electronic means or other) without the written permission of
the copyright holder.
Applications for the copyright holder’s written permission to reproduce any part of this publication should
be addressed to Smartgen Technology at the address above.
Any reference to trademarked product names used within this publication is owned by their respective
companies.
Smartgen Technology reserves the right to change the contents of this document without prior notice.
Software Version
Version
Date
Note
1.0
2016-01-19
Original release.

CMM366-ET Cloud Monitoring Communication Module User Manual
CMM366-ET Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 3 of 18
CONTENT
1 OVERVIEW...................................................................................................................4
2 PERFORMANCE AND CHARACTERISTICS ...............................................................4
3 SPECIFICATION...........................................................................................................5
4 PANEL AND TERMINAL DESCRIPTION......................................................................6
4.1 PANELINDICATORAND BUTTONS.......................................................................6
4.2 GPRS......................................................................................................................7
4.3 GPS.........................................................................................................................7
4.4 SIM INSTALLATION................................................................................................7
4.5 RS485.....................................................................................................................8
4.6 RS232.....................................................................................................................8
4.7 LINK........................................................................................................................8
4.8 USB HOST..............................................................................................................9
4.9 USB DEVICE...........................................................................................................9
4.10 TERMINAL............................................................................................................10
5 PROGRAMMABLE PARAMETERS ............................................................................11
5.1 CONTENTSAND SCOPES OFPARAMETERS....................................................11
5.2 PC CONFIGURATION INTERFACE......................................................................15
6 SYSTEM DIAGRAM....................................................................................................16
7 CASE DIMENSION AND INSTALLATION...................................................................17
8 FAULT FINDING .........................................................................................................18

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 4 of 18
1 OVERVIEW
CMM366-3G Cloud Monitoring Communication Module is GPRS wireless network communication
protocol switch module which can achieve genset (with SCI) connect to Internet. The module gains
genset data via RS485 port, USB port, LINK port or RS232 port of genset controller modules of
international first-class brands including SmartGen, DeepSea, ComAp, etc. Then the module transmits
the data to corresponding cloud server via GPRS wireless network for achieving user’s real-time
monitoring to running status and searching of running records via APP (IOS or Android) and pc terminal
devices.
CMM366-3G module has already integrated protocols of mainstream genset control module. It not only
can achieve genset monitoring but also can insert some digital alarm input/output signal to achieve
monitoring of generator room entrance guard, guard against theft and fire facilities.
This module, which has GPS locate function, can upload gained longitude, latitude and elevation to
corresponding cloud server.
2 PERFORMANCE AND CHARACTERISTICS
1) Connect to cloud server via WCDMA3G&GPRS 2G, one to one monitoring;
2) Multiple ports for communication with genset control module: RS485, RS232, LINK and USB
(Host); can monitor great majority genset control modules of international first-class brands;
3) Widely power supply: DC (8~35)V, can direct use genset build-in battery;
4) With ARM-based 32-bit SCM, high integration of hardware and strong programming ability;
5) Include with GPS locate function to achieve gain location information and locate genset;
6) Take JSON network data communication protocol, upload real-time data variation and take
compression algorithm to vastly reduce network flow at the same time;
7) Users can set up history data upload rest to upload monitoring data to server (history data can be
analyzed);
8) When alarm occurs it can upload data to server immediately;
9) 2 auxiliary digital input ports which can receive external alarm signal;
10) 1 auxiliary relay output ports which can output various of alarm signal;
11) Power and multiple communication status indicators on front panel that working status is clear at a
glance;
12) Lamp test function;
13) Parameter adjust function: users can adjust parameters via USB port;
14) Take standard π-type 35mm guide-rail installation or screw-fixed installation that the module can
be installed in the genset control box;
15) Modular design, self extinguishing ABS plastic shell, light weight, compact structure with easy
installation.

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 5 of 18
3 SPECIFICATION
Items
Contents
Operating Voltage
DC 8.0V~35.0V, continuous power supply.
Power Consumption
Standby: ≤2W
Working: ≤5W
Auxiliary Input
Digital Input, connect (B-) is active.
Auxiliary Output
1A DC30V Volts free output
USB Host
A-type USB mother port
RS485
Seclusion type
RS232
General type
LINK
SmartGen exclusive port
USB Device
B-type USB mother port
GPRS Port
Standard SMA port (female), SMA port (male) for antenna.
GPS Port
Standard SMA port (female), SMA port (male) for antenna, active antenna.
Wireless Network
WCDMA 3G GPRS 2G
Case Dimensions
73mmx105mmx33mm
Working Conditions
Temperature: (-30～+70)°C Humidity: (20～93)%RH
Storage Condition
Temperature: (-40～+80)°C
Weight
0.15kg

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 6 of 18
4 PANEL AND TERMINAL DESCRIPTION
4.1 PANEL INDICATOR AND BUTTONS
Icon
Note
POWER/ALARM
GreenLED Light: Power supply normal indicator
RedLED Light: Common alarm indicator
RS485(Red)
Normally Extinguish: RS485 disabled
Normally Light: Communication fail
Blink: Communication normal
USB(Red)
Normally Extinguish: USB(Host) disabled
Normally Light: Communication fail
Blink: Communication normal
GPS(Red)
Normally Extinguish: GPS disabled
Normally Light: GPS not gained satellite signal
Blink: GPS gained satellite signal
LINK(Red)
Normally Extinguish: Disabled
Normally Light: Communication fail
Blink: Communication normal
RS232(Red)
Normally Extinguish: RS232 disabled
Normally Light: Communication fail
Blink: Communication normal
GPRS/3G(Red)
Extinguish: CMM366-3G login with server unsuccessfully
Light: Login with server successfully
Blink: Real-time communication normal
Lamp test/Rest:
Press this button for 1s, all the LEDs are illuminated; press for 10s, reset the module to default and all
the LEDs blink for 3 times.
Note: After reset the module, set up the parameters via PC software is recommended. Please
operate cautiously.

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 7 of 18
4.2 GPRS
Connect GPRS antenna to GRPR/3G port.
Antenna: 50Ω/SMA female.
4.3 GPS
GPS enabled, connect GPS antenna to CMM366-3G.
Note: GPS antenna needs to be placed to open outdoors, otherwise location information may not
accurate or cannot be gained.
Antenna: 50Ω/SMA female, active antenna.
Note: GPRS antenna and GPS antenna cannot be connected reversely.
4.4 SIM INSTALLATION
Insert 3G or 2G SIM card. CMM366-3G will connect to servers via GPRS network.
Note: WCDMA 3G network, all 2G network are supported. Use standard SIM card (25mmX15mm); If
GPS indicator and GPRS indicator blink in the same time, which means SIM card hasn’t been inserted or
bad contacts.
After detached 4 screws in the shell, the installation steps are as below:

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 8 of 18
4.5 RS485
Receive genset data information by CMM366 RS485 port connecting with Genset Controller RS485 port.
If communication is abnormal, 120Ω terminal resistance is recommonded. One end of shield wire hangs
in the air and the other one connects with SCR.
4.6 RS232
Receive genset data information by CMM366 RS232 port connecting with Genset Controller RS232 port.
4.7 LINK
Receive genset data information by CMM366 LINK port connecting with Genset Controller LINK port.

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 9 of 18
4.8 USB HOST
Receive genset data information by CMM366 A-type USB mother port connecting with Genset Controller
USB port.
4.9 USB DEVICE
Set up all the parameters and view CMM366-3G ID&Login password by CMM366 USB port connecting
with PC USB port.

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 10 of 18
4.10 TERMINAL
No.
Function
Cable Size
Note
1
B-
1.0mm2
Connected with negative of starter battery.
2
B+
1.0mm2
Connected with positive of starter battery. 3Afuse
is recommended.
3
Aux. Input 1
1.0mm2
Active when connect to B-.
4
Aux. Input 2
1.0mm2
Active when connect to B-.
5
Aux. Output
Normally
Open
1.0mm2
Normally open outputs, rated 1A DC30V
6
Common
1.0mm2
7
Normally
Close
1.0mm2
8
RS485 B(-)
0.5mm2
Impedance-120Ω shielding wire is recommended,
its single-end earthed.
9
RS485A(+)
0.5mm2
10
RS485 (SCR)
0.5mm2
11
RS232 RX
0.5mm2
RS232
12
RS232 TX
0.5mm2
13
RS232 GND
0.5mm2

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 11 of 18
5 PROGRAMMABLE PARAMETERS
5.1 CONTENTS AND SCOPES OF PARAMETERS
Form1
No.
Items
Parameters
Defaults
Description
Gateway
1
Website
(0-65535)
20 Chinese characters, letters or
numbers
2
URL
(0-65535)
monitor.smartgen.com.cn
40 characters
3
Server Port
(0-65535)
81
4
Password
(0-65535)
123456
16 characters
GPS
1
GPS Enabled
(0-1)
0
0: Disabled 1: Manual Input
2
Longitude
(-180-180)°
0.000000
GPS location, altitude
3
Latitude
(-90-90)°
0.000000
4
Altitude
(-9999.9-9999.9)
100.0
GSM
1
GSM Enabled
(0-1)
1
0:Disabled; 1:Enabled
2
GPRS Password
Reserved
3
Message Center
Reserved
Cloud Server
1
Auto Gain Comm.
Port
(0-1)
1
0:Disabled; 1:Enabled
2
ID
(1-254)
1
Module ID
3
Communication Port
(0-4)
2
0:Disabled;
1:LINK;
2:RS485;
3:RS232;
4:USB
4
Baud Rate
(0-2)
0
0:9600bit/s;
1:19200bit/s
2:Reserved
5
Location Info
(0-1)
0
0: Manual input location info
1: Use GPS to gain location
6
Longitude
(-180-180)°
0.000000
Manually set module location and
elevation.
7
Latitude
(-90-90)°
0.000000
8
Altitude
(-9999.9-9999.9)
100.0
9
Type
(0-65535)
6000
See: Form4
10
Name
(0-65535)
Module Names(20 Chinese characters, letters or
numbers)
11
Debug Staff Name
20 Chinese characters, letters or numbers
12
Telephone
20 Chinese characters, letters or numbers
13
Installation Time
20 Chinese characters, letters or numbers
14
History Data Rest
(0-3600)s
0
History data upload rest.
Note: No upload when it is 0s
15
Time Zone
(-12-12)
8
Time Zone

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 12 of 18
Module Configuration Info
1
Type
(0-5)
1
0:AMF module
1:Single-unit self-starting module
2: Single-single parallel module
3:Mains-genset parallel module
4:Mains-bus parallel module
5:Bus-bus parallel module
Note: The parameter will auto change
according to genset type.
2
Rated Speed
(0-6000)r/min
1500
Rated Speed
3
AC Supply
(0-3)
0
0:3P4W;1:3P3W;2:2P3W;3:1P2W。
4
Rated Volt
(30-30000)V
230
Rated Volt
5
Rated Freq
(10-600)Hz
50
Rated Freq
6
Rated Current
(5-6000)A
500
Rated Current
7
Rated Power
(0-6000)kW
276
Rated Power
8
Custom Description 1
(0-65535)
Custom Description (20 Chinese characters,
letters or numbers)
9
Custom Description 2
(0-65535)
Custom Description (20 Chinese characters,
letters or numbers)
10
Custom Description 3
(0-65535)
Custom Description (20 Chinese characters,
letters or numbers)
11
Custom Description 4
(0-65535)
Custom Description (20 Chinese characters,
letters or numbers)
12
Custom Description 5
(0-65535)
Custom Description (20 Chinese characters,
letters or numbers)
Digital Input
Digital Input 1
1
Setting
(0-9)
0
Default: Not used
2
Type
(0-1)
0
0:Active when close
1:Active when open
See: Form2
3
Delay
(0-20.0)
0.0
Action delay
Digital Input 2
3
Setting
(0-9)
1
Default: Lamp test
4
Type
(0-1)
0
0:Active when close
1:Active when open
See: Form2
5
Delay
(0-20.0)
0.0
Action delay
Digital Output
1
Setting
(0-14)
0
Default: Not used
See: Form3

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 13 of 18
Form2
No.
Item
Description
0
Not Used
Not used.
1
Lamp Test
All the indicators are illuminated when input is active.
2
Remote Control Inhibited
Cloud start/stop control is prohibited when input is active.
3
Access Alarm Input
Access alarm is uploaded to server when input is active.
4
Fire Alarm Input
Fire alarm is uploaded to server when input is active.
5
Alarm Input
External alarm is uploaded to server when input is active.
6
Reserved
7
Reserved
8
Reserved
9
Factory Test Mode
It is only used for factory hardware port test when active.
Form3
No.
Item
Description
0
Not used
Output port won’t output when this item is selected.
1
Digital Input 1 Active
Output when auxiliary input 1 is active.
2
Digital Input 2 Active
Output when auxiliary input 2 is active.
3
RS485 Comm. Fail
RS485 communication fails.
4
Network Comm. Fail
Network communication fails.
5
LINK Comm. Fail
LINK communication fails.
6
RS232 Comm. Fail
RS232 communication fails.
7
Common Alarm
Output when there is an alarm.
8
Reserved
9
Reserved
10
Reserved
11
Reserved
12
Reserved
13
Reserved
14
Reserved

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 14 of 18
Form4
Manufacturers
Type
Note
SmartGen
HGM6110
Single-unit self-starting module
HGM6120
AMF module
HGM7x10
Single-unit self-starting module
HGM7x20
AMF module
HGM410
Single-unit self-starting module
HGM420
AMF module
HGM9120
AMF module
HGM9210
Single-unit self-starting module
HGM9220
AMF module
HGM9310
Single-unit self-starting module
HGM9320
AMF module
HGM9410
Single-unit self-starting module
HGM9420
AMF module
HGM9510
Single-single parallel module
HGM9520
Mains-genset parallel module
HGM9530
Single-single parallel module
HGM9540
Mains-genset parallel module
HGM9560
Mains-bus parallel module
HGM9580
Bus-bus parallel module
HGM9610
Single-unit self-starting module
HGM9620
AMF module
DeepSea
DSE7110MKII
Single-unit self-starting module
DSE7120MKII
AMF module
DSE7210
Single-unit self-starting module
DSE7220
AMF module
DSE7310
Single-unit self-starting module
DSE7320
AMF module
DSE7410
Single-unit self-starting module
DSE7420
AMF module
DSE7450
Single-unit self-starting module
DSE8610
Single-single parallel module
DSE8620
Mains-genset parallel module
ComAp
MRS10 Ⅱ
Single-unit self-starting module
MRS16 Ⅱ
Single-unit self-starting module
AMF25 Ⅱ
AMF module
Harsen
GU620A
Single-unit self-starting module
GU621A
AMF module
GU630A
Single-unit self-starting module
GU631A
AMF module

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 15 of 18
5.2 PC CONFIGURATION INTERFACE
The USB port of CMM366-3G communication module connects PC port to configure the parameters.
Gateway Configuration
Cloud Server Configuration
Module Monitoring Interface

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 16 of 18
6 SYSTEM DIAGRAM
1 CMM366-3G module connects with 1 genset monitor module. It can be connected via RS485 port,
LINK port, RS232 port or USB port.
图1 CMM366-3G System Diagram

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 17 of 18
7 CASE DIMENSION AND INSTALLATION
2 ways for installation: 35mm guide rail in box or screw (M4) installation as below:
CMM366-3G Case Dimension
CMM366-3G Guide Rail Installation
CMM366-3G Screw Installation

CMM366-3G Cloud Monitoring Communication Module User Manual
CMM366-3G Cloud Monitoring Communication Module 2016-01-19 Version 1.0 Page 18 of 18
8 FAULT FINDING
Symptoms
Possible Solutions
Controller no response with
power.
Check power voltage;
Check controller connection wirings.
Network Indicator Not Light
Check SIM card is inserted or not;
Check GPRS antenna is connected or not.
GPS Not Gained Location
Check GPS parameters are enabled or not;
Check GPS antenna is connected or not and placed outdoor or not.
RS485 Communication
Abnormal
Check connections;
Check RS485 port is enabled or not;
Check settings of genset ID and baud rate are correct or not.
Check RS485’s connections of A and B is reverse connect or not.
RS232 Communication
Abnormal
Check connections;
Check RS232 port is enabled or not;
Check settings of genset ID and baud rate are correct or not.
LINK Communication
Abnormal
Check connections;
Check LINK port is enabled or not;
Check settings of genset ID and baud rate are correct or not.