SMC Networks EX120-SDN1 User manual

OPERATION MANUAL
SMC Corporation
SI unit
EX120-SDN1
Doc.No. EX## -OME0015
EX121-SDN1
EX122-SDN1
EX124D/U-SDN1

Contents
1.Safety instructions ------------------------------------------------------ P3
2.Specifications
2-1.General specifications ------------------------------------------------------ P4
2-2.Electrical and network specifications ------------------------------------------------------ P4
2-3.Applicable solenoid valve series ------------------------------------------------------ P5
3.Wiring and setting
3-1.Connection type ------------------------------------------------------ P5
3-2.Address setting ------------------------------------------------------ P8
4.LED indicator and Physical dimensions
4-1.LED indication ------------------------------------------------------ P9
4-2.Physical dimensions ------------------------------------------------------ P9
5.EDS(Electronic Data Sheet) File ------------------------------------------------------ P12
6.Trouble Shooting ------------------------------------------------------ P13
SMC CORPORATION
Doc.No.EX##-OME0015
- 2 -

SMC CORPORATION
Doc.No.EX##-OME0015
1.Safety instructions
These safety instructions are intended to prevent a hazardous situation and/or equipment damage. These instructions indicate
the level of potential hazard by label of "CAUTION" , "WARNING".
To ensure safety, be sure to observe ISO, JIS and other safety practices.
CAUTION: Operator error could result in injury or equipment damage.
WARNING: Operator error could result in serious injury or loss of life.
CAUTION
Thoroughly read this manual and operate the product within the specified range. Follow the instructions.
Do not drop or impart any impact to the product.
Use within specified voltage range. Use outside of specified voltage will cause malfunction, damage of unit, electric shock, and
fire.
Do not touch the terminal or internal circuit board while they are energized. It may cause malfunction, damage to unit, and
electric shock.
Use within operating ambient temperature. Do not use where temperature can rapidly change even thought it is within the
specifications.
Foreign objects should be prevented from entering the product. Contamination by foreign objects, such as wire chips will cause
fire, breakage, and malfunction.
Use within the operating environment of the protection structure. In case of IP20, avoid use in the place where water and oil
scatter. To realize IP65, install manifold properly and give some prevention against splash of liguid to electrical entry.
Carry out periodical checks to confirm correct operation. Safety may not be maintained by unintentional malfunction or incorrect
operation. Design must consider the space necessary for maintenance.
As the contents of this manual is sometimes changed without the previous announcement, understand them beforehand,
please.
SI unit is not explosion proof. Operation in explosive enviromment may cause explosion accident.
WARNING
The product specified here is designed to be used in standard factory automation equipment. Do not use in machinery and/or
equipment where operators may be injured, and malfunction or failure may cause loss of life.
Do not disassemble to repair or modify the product.
Connection
CAUTION
Power of the product and all other equipments should be turned off while wiring.
Tighten the wiring with connector and tarminal screw completely. Short circuit, fire, and malfunction will be caused if connector
and tarminal screw are not tightened enough.
Avoid incorrect wiring. It may damage the product and/or other equipments.
Ensure that the FG terminal is correctly grounded.
Power with correct capacity should be prepared by considering the in-rush current when starting.
Influence of noise should be avoided for the wiring. Wiring should be separated from power cables and high voltage cables.
Ensure that the power is within the specified voltage range.
Ensure that the cable is capable of supporting the solenoid valve and SI unit in terms of rating.
Applicable solenoid valves
CAUTION
SMC offers no guarantee against malfunction and damage of unit when valves not described to “2-3.Applicable solenoid
valve series” and loads which is not valve are connected.
- 3 -

- 4 -
2-1. General specifications
Item Specifications
Model EX120
-SDN1
EX121
-SDN1
EX122
-SDN1
EX124D
-SDN1
EX124U
-SDN1
Operating ambient temp. 0 to +55(with 8 points of valve ON)
0 to +50℃(with 16 points of valve ON)
Operating ambient humidity 35 to 85%RH(No dew condensation)
Storage ambient temp. -20 to +60℃
Vibration proof 50m/s2 (comply with JIS C 0911)
Impact proof 100m/s2 (comply with JIS C 0912)
Noise immunity Normal mode ±1500 V Pulse 1µs
Common mode ±1500 V Pulse 1µs
Radiation 1000 V ±Pulse 1µs
Withstand voltage AC1000V for 1 min. between FG and external
terminal package.
Insulation resistance DC500V, 2MΩbetween FG and external terminal
package.
Operating environment No corrosive gas and no dust
Weight 110g
or less
140g
or less
130g
or less
240g
or less
Protection class IP20 IP65
2-2. Electrical and network specifications
Item Specifications
Applicable system DeviceNet Release 2.0
Power supply voltage for communication DC11V to DC25V
(supplied by communication connector)
Power supply voltage for solenoid valve DC24V +10% -5%
Communication and
Internal power supply
90mA or less (DC24V)Consumption
current
Power supply for
Solenoid valve
1.5A or less (DC24V)
Output style NPN output (Open collector)
Connected load DC24V, Solenoid valve with lamp-surge voltage
protection circuit of 2.1W or less.
(made by SMC)
Solenoid valve
Connection
spec.
Insulation type Opt-coupler insulation type
Residual voltage 0.4V DC or less
Applicable DeviceNet VolumeⅠ- Release 1.2
VolumeⅡ- Release 1.1
MAC ID setting range 0 to 63 (Set by Dip switch)
Baud Rate (Transmission speed) 500kbps, 250kbps, 125kbps (Set by Dip switch)
Slave (branch station) type Group 2 only server
Connection type T branch type, Multi drop type
Device type 16
Product code 288
Revision Referred to EDS file.
Vendor ID 7
Network connection spec.
Corresponding message Polled command (I/O message ), Explicit message
2. Specifications SMC CORPORATION
Doc.No.EX##-OME0015

- 5 -
3. Wiring and Setting
2-3. Applicable solenoid valve series
SI unit Valve series
EX120 VQ1000, VQ2000
EX121 VQ1000, VQ2000, SX3000, SX5000
EX122 SY3000, SY5000
EX124U/D VQ2000, VQ4000, VQ5000
Terminal resistance
Node Node
NodeNode
Node
Node
Node
Node
Node
Branch
line
Branch
line
Branch
line
T branch
Branch line
branch
Main line
Multi branch
Terminal resistance
Communication
distance Baud rate Total length of trunk
Length of
branch line
Total length of
branch line
500 kbps 100m or less 39m or less
250 kbps 250m or less 78m or less
Thick cable
125 kbps 500m or less
6m or less
156m or less
Thin cable Common 100m or less ――――――
Terminal resistance 121 ohm (1/2W)
Length of cable
3-1.Connection type
DeviceNet can be connected by T branch, Multi branch, Branch line branch and Multi drop. Total
extension length of trunk and Branch line is different for different Baud rate and thickness of
communication cable.
SI unit I/O data (Receiving and sending data of polled command)
Item Output(Poll request) Input(Poll response)
Occupied byte 2 byte
(Solenoid valve output)
2 byte
Address +0 Output No. 0 to 7Sending/
receiving data Address +1 Output No. 8 to 15
Bit of each output data and corresponding solenoid valve no.
Offset MSB LSB
0 No.7 No.6 No.5 No.4 No.3 No.2 No.1 No.0
1 No.15 No.14 No.13 No.12 No.11 No.10 No.9 No.8
SMC CORPORATION
Doc.No.EX##-OME0015
*) Mapping method of sending / receiving data is different by PLC.
For further information, refer to the manual for PLC master (scanner)

- 6 -
Cable specification
CAUTION
For Multi drop connection, prepare plug connector for T branch separately.
(Example, TMSTBP 2.5...- STF -5.08 made by Phoenix Contact Corp.)
Use DeviceNet special cable for communication cable.
Be sure to connect DeviceNet special terminal resistor with both ends of trunk.
SMC CORPORATION
Doc.No.EX##-OME0015
Thickcable Thincable
Item Communication
Signal Power upply Communication Signal Power supply
Conductor
cross section 0.82 mm21.65 mm20.20 mm20.33 mm2
Colors Blue, White Red, Black Blue, White Red, Black
Impedance 120Ω±
10%(1MHz) ―― 120Ω±
10%(1MHz) ――
Propagation
delay 1.36ns / ft(max) ―― 1.36ns / ft(max) ――
Attenuation
rate
500k：0.25dB / ft
125k：0.13dB / ft
1.00M：0.40dB / ft
――
500k：0.50dB / ft
125k：0.29dB / ft
1.00M：0.70dB / ft
――
Conductor
resistance
6.9Ω/
1000ft(max)
3.6Ω/
1000ft
(max)
28Ω/
1000ft(max)
17.5Ω/
1000ft(max)

Wiring of cable for solenoid valve power supply and communication
Communication connector for DeviceNet
Terminal Wire color Connected to
V- Black (-) side of power supply cable
CANL Blue Low side of communication cable
FG - Ground / Shield
CANH White High side of communication cable
V+ Red (+) side of power supply cable
Power supply connector for solenoid valve
Terminal Wire color Connected to
24V - (+) side of solenoid valve source supply
0V - (-) side of Solenoid valve source supply
CAUTION
• Before wiring, be sure to turn power supply off.
• Screw for connectors is M3. Tighten them properly by torque of 0.5 to 0.6 [N·m].
• SI unit isn’t available for monitoring of power supply for solenoid valve.
• Do not put cable specified by DeviceNet with/near high voltage line or strong
electric line such as driving line.
- 7 -
SMC CORPORATION
Doc.No.EX##-OME0015

3-2. Address setting
Before setting of address by DIP switch, turn power supply for communication cable in SI
unit “OFF”.
Setting (binary) of following items is available by DIP switch installed to cover.
1) Node address (00 to 63)
2) Communication speed (125kbps, 250kbps, 500kbps)
- 8 -
SMC CORPORATION
Doc.No.EX##-OME0015
<Setting of node address>
SW1 SW2 SW3 SW4 SW5 SW6
Node
address 12481632
#0 000000
#1 100000
#2 010000
:
:
:
#62 011111
#63 111111
<Setting of communication speed>
Setting Max. transmission distance (m)
Length of trunk
SW7 SW8
Communication
speed (kbps) Thick
cable
Think
cable
Length
of
branch
line
Total length
of
branch line
0 0 125 500 156
1 0 250 250 78
0 1 500 125
100 6
39
1 1 Not used Not used
CAUTION
• When shipped, node address of 63 and communication speed of 125kbps are set in
advance.
• When communication error occurs, output condition is cleared.
ON

4.LED indicator and Physical dimensions
- 9 -
Indication Contents
PWR Green Lights up when power for DeviceNet line is supplied.
Lights off SI unit isn’t on line or power supply for communication
line isn’t turned on.
Green
flashing Waiting for connection (ON line)
Green
lights up Connection completed (ON line)
Red
flashing Connection time out (Minor communication error)
MOD / NET
Red
lights up
MAC ID duplication error or BUS OFF error
(Major communication error)
4-1 LED indication
EX120-SDN1
EX121-SDN1
EX122-SDN1
EX124D-SDN1
EX124U-SDN1
4-2 Physical dimensions
SI unit (EX120-SDN1)
SMC CORPORATION
Doc.No.EX##-OME0015
1
1
1
1
0
0
2
2
3
3
4
4
5
5
6
6
7
7
8
8
0
0
1
1
2
2
4
4
8
8
16
16
32
32
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
2
2
1
1
0
0
0
0
0
0
0
0
0
0
62
62
1
1
0
0
1
1
1
1
1
1
1
1
63
63
1
1
1
1
1
1
1
1
1
1
1
1
STATION
STATION
ADDRESS
ADDRESS
TRANSMIT
TRANSMIT
SPEED
SPEED
125K
125K
250K
250K
500K
500K
0
0
0
0
1
1
0
0
0
0
1
1
1
1
1
1
SWITCH
SWITCH
SETTINGS
SETTINGS
ON
ON
SERIAL UNIT
SERIAL UNIT
SMC
SMC
28.8
28.8
10.2
10.2

- 10 -
SI unit (EX122-SDN1)
SI unit (EX121-SDN1)
SMC CORPORATION
Doc.No.EX##-OME0015
1
1
1
1
0
0
2
2
3
3
4
4
5
5
6
6
7
7
8
8
0
0
1
1
2
2
4
4
8
8
16
16
32
32
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
0
0
0
0
0
2
2
1
1
0
0
0
0
0
0
0
0
0
0
62
62
1
1
0
0
1
1
1
1
1
1
1
1
63
63
1
1
1
1
1
1
1
1
1
1
1
1
STATION
STATION
ADDRESS
ADDRESS
TRANSMIT
TRANSMIT
SPEED
SPEED
125K
125K
250K
250K
500K
500K
0
0
0
0
1
1
0
0
0
0
1
1
1
1
1
1
SWITCH
SWITCH
SETTINGS
SETTINGS
ON
ON
Flat cable length about 70mm
Flat cable length about 70mm
SERIAL UNIT
SERIAL UNIT
SMC
SMC
64
64
60.8
60.8
66.1
66.1
28.8
28.8
2
2
10.2
10.2
5.4
5.4

SI unit (EX124D-SDN1)
SI unit (EX124U-SDN1)
- 11 -
SMC CORPORATION
Doc.No.EX##-OME0015
4-G(PF)1/2
19
19.8
114
5.5 67
(72.5)
53.8
11.6

5.EDS (Electronic Data Sheet) File SMC CORPORATION
Doc.No.EX##-OME0015
The EDS File is a file which described ID information on SI unit and important information in the
operation.
The DeviceNet controller or scanner automatically recognizes the SI unit by referring to the EDS File.
* Please refer to the undermentioned list when DeviceNet controller or the scanner dose not
automatically recognize the EDS File.
- 12 -
$ Electronic Data Sheet File for
$ SMC EX120-SDN1 Serial Interface Unit
[File]
DescText = "SMC EX120-SDN1 EDS File";
CreateDate = 05-20-1999; $ created
CreateTime = 10:30:00;
Revision = 1.1; $ Revision of EDS
[Device]
VendCode = 7;
VendName = "SMC Corp.";
ProdType = 16;
ProdTypeStr = "General Motion Controller";
ProdCode = 288;
MajRev = 2; $ Device Major Revision
MinRev = 7; $ Device Minor Revision
ProdName = "Valve Manifold SIU";
Catalog = "EX120-SDN1";
[IO_Info]
Default = 0x0001; $ Poll(Bit 0)
PollInfo = 0x0001 , 1 , 1; $ Prod. Cnxn=1
$ Cons. Cnxn=1
Input1 = 2, $ 2 byte
0, $ All bits are significant
0x0001, $ Poll Only Connection
"Solenoid Status", $ Name String
6, $ Path Size
"20 04 24 05 30 03", $ Assy Obj Inst 5 Attr 3
""; $ Help String
Output1 = 2, $ 2 byte
0, $ All bits are significant
0x0001, $ Poll Only Connection
"Solenoid Output", $ Name String
6, $ Path Size
"20 04 24 23 30 03", $ Assy Obj Inst 23 Attr 3
""; $ Help String

6. Trouble Shooting
- 13 -
MOD/NET LED Cause & Countermeasure
Lights off PWR LED lights off
<Countermeasure>
Confirm that power for SI unit circuit is supplied.
Confirm correct wiring.
If above countermeasures do not improve status, please exchange SI unit.
PWR LED lights up
<Countermeasure>
Confirm that baud rate is set correctly.
If MOD/NET LED lights off in spite of baud rate is set correctly, change SI unit.
Green flashing Connection waiting
Shows communication waiting status between SI unit and master.
<Countermeasure>
Confirm master operate correctly.
If using scan list, ensure slave is recorded to scan list correctly.
Red flashing Communication wire disconnected error
<Countermeasure>
Confirm communication wire is not disconnected.
<Remark>
Red flashing if master power source is turned off during communication.
Red lights up Node address overlapping error
<Countermeasure>
Confirm there is no overlapping on the node address.
BUS OFF error
Detects communication error.
<Countermeasure>
Case 1
Communication error due to noise.
Confirm there is no component or high voltage cable that generate noise
around communication wire.
Make some distances between communication wire and noise source.
Case2
Communication cable problem.
Confirm terminal resistance (121ohm) connects to the both ends of
communication wire that is main wire of communication wire.
If red MOD/NET LED is still lights up in spite of above countermeasures,
change SI unit.
CAUTION
When red MOD/NET LED is lit, even if cause is solved, SI unit do not do auto-recovery. In
this case, please reset the power to SI unit circuit (Communication/Internal power supply).
SI unit isn’t available for monitoring of power supply for solved valve.
SMC CORPORATION
Doc.No.EX##-OME0015