SMC Networks 9452TX User manual

SMC9452TX

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is
assumed by SMC for its use, nor for any infringements of patents or other rights of third parties, which may result from its
use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to
change specifications at any time without notice.
SMC Networks, Inc.
38 Tesla
Irvine, CA 92618
Copyright © SMC Networks, Inc., 2003. All rights reserved.
SMC is a registered trademark; and Barricade is a trademark of SMC Networks, Inc.
Other product and company names are trademarks or registered trademarks of their respective holders.

EZ Card™ 1000 SMC9452TX
10/100/1000 Mbps Copper Gigabit PCI Card
Thank you for choosing the SMC Networks Wired 10/100/1000
Network Interface Card (SMC9452TX). This EZ Quick Installation
Guide provides simple setup instructions. For additional informa-
tion, see the manual included on the CD-ROM.
Box Contents:
One EZ Card™ 1000 (SMC9452TX)
One Quick Installation Guide
One CD containing: EZ Installation Wizard, Manual, and Driver
Before you begin installation please verify the following:
•All of the box contents are included
•Atleast one windows-based desktop computer has a
CD-ROM Drive
•You have an Ethernet cable to attach to hub, switch, broadband
router, broadband modem etc..
*NOTE: Please DO NOT install the SMC9452TX prior to running the
EZ Installation Wizard.

Once you have removed the SMC9452TX contents from the
box, you are ready to install the EZ Installation Wizard.
•Ifthe computer is off, turn it on
•When the computer boots up, insert the SMC9452TX
CD-ROM into the CD-ROM drive of the computer that you
are going to install the SMC9452TX
NOTE:If the EZ Installation Wizard does not start automatically,
follow the steps below to start the program:
1. Double-click the [My Computer] icon.
2. Double-click on the CD-ROM or Compact Disk icon to view
the contents of the Installation CD.
3. Click on the [EZ Install] icon to launch the program.

NOTE: Network cards are sensitive to static electricity.To protect the card,
avoid touching its electrical components and always touch the metal
chassis of your computer before handling the card.
1. Switch off the computer, unplug the power cord, and remove
the computer’s cover.
2. Select an unused PCI bus-master slot and remove its protective
bracket.
3. Carefully insert the card and press until all the edge connectors
are firmly seated inside the slot.Then screw the card’s bracket
securely into the PC’s chassis.
4. Connect the EZ Card™ 1000 (SMC9452TX) directly to a 10BASE-T
or 100BASE-TX hub or switch using UTP cable (Category 3, 4,or
5 for 10BASE-T; Category 5 for 100BASE-TX).The maximum allow-
able length of UTP cable connections is 100 meters (328 ft).
When inserting an RJ-45 plug, be sure the tab on the plug
clicks into position to ensure that it is properly seated.
5. Replace the computer’s cover and power it on. Once the
computer has booted you will be networked!

FOR TECHNICAL SUPPORT, CALL:
From U.S.A. and Canada (24 hours a day, 7 days a week)
(800) SMC-4-YOU; Ph: [phone]; Fax: [phone]
From Europe : Contact details can be found on
www.smc-europe.com or www.smc.com
INTERNET
E-mail addresses:
t[email protected]
european.techsuppor[email protected]
Driver updates:
http://www.smc.com/index.cfm?action=tech
support drivers downloads
World Wide Web:
http://www.smc.com/
http://www.smc-europe.com/
If you are looking for further contact information, please visit
www.smc.com or
www.smc-europe.com
38 Tesla
Irvine, CA 92618
Phone: [phone]
Model Number: SMC9452TX
Publication Number: 150200006400A
Edition Number: 01-012084-215