SMC Networks 6704FMSC User manual

1
 4 expansion slots to configure flexible network
 One built-in intelligent module with RS-232 console port
 Supports half-duplex mode for backpressure, and
full-duplex for flow-control
 Store-and-Forward switching architecture for abnormal
packet filtering
 SNMP management
 Console and Telenet management
 Port trunking supported
 IGMP supported
 Port Mirror
 MIB II and Private MIB supported
 Port Security
InstallationGuide
SMC6704M
Tiger Switch 10/100/1000

2
LIMITED WARRANTY
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its
products to be free from defects in workmanship and materials, under
normal use and service, for the applicable warranty term. All SMC products
carry a standard 90-day limited warranty from the date of purchase
from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or
replace any product not operating as warranted with a similar or
functionally equivalent product, during the applicable warranty term. SMC will
endeavor to repair or replace any product returned under warranty
within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty
by registering new products within 30 days of purchase from
SMC or its Authorized Reseller. Registration can be accomplished via the
enclosed product registration card or online via the SMC web site.
Failure to register will not affect the standard limited warranty. The Limited
Lifetime warranty covers a product during the Life of that Product,
which is defined as the period of time during which the product is an “Active”
SMC product. A product is considered to be “Active” while it is
listed on the current SMC price list. As new technologies emerge, older
technologies become obsolete and SMC will, at its discretion, replace an
older product in its product line with one that incorporates these newer
technologies. At that point, the obsolete product is discontinued and is no
longer an “Active” SMC product. A list of discontinued products with their
respective dates of discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty.
All products that are replaced become the property of SMC. Replacement
products may be either new or reconditioned. Any replaced or repaired
product carries either a 30-day limited warranty or the remainder of the initial
warranty, whichever is longer. SMC is not responsible for any
custom software or firmware, configuration information, or memory data of
Customer contained in, stored on, or integrated with any products
returned to SMC pursuant to any warranty. Products returned to SMC should
have any customer-installed accessory or add-on components, such
as expansion modules, removed prior to returning the product for replacement.
SMC is not responsible for these items if they are returned with
the product.
Customers must contact SMC for a Return Material Authorization number prior
to returning any product to SMC. Proof of purchase may be

3
required. Any product returned to SMC without a valid Return Material
Authorization (RMA) number clearly marked on the outside of the
package will be returned to customers at customer’s expense. For warranty
claims within North America, please call our toll-free customer
support number at [phone]. Customers are responsible for all shipping
charges from their facility to SMC. SMC is responsible for return
shipping charges from SMC to customer.
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE
AS WARRANTED ABOVE, CUSTOMER’S SOLE
REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN
QUESTION, AT SMC’S OPTION. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF
ALL OTHER WARRANTIES OR CONDITIONS,
EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW,
STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. SMC NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH
THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.
SMC SHALL NOT BE LIABLE UNDER THIS
WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE
ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST
OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE,
NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE
BEYOND THE RANGE OF THE INTENDED USE, OR BY
ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE),
SHALL SMC BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND,
OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER
FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE,
FAILURE, OR INTERRUPTION OF ITS PRODUCTS,
EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED

4
WARRANTIES OR THE LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
WHICH MAY VARY FROM STATE TO STATE.
NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR
STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from
the active SMC price list. Under the limited lifetime warranty,
internal and external power supplies, fans, and cables are covered by a
standard one-year warranty from date of purchase.
SMC Networks, Inc.

5
LIMITED WARRANTY................................................................................................2
1. Introduction........................................................................................6
2. Product Overview...................................................................10
3. Network Configuration...................................................16
4. Connecting to the Network.......................................20
5.Web-Based Management...............................................33
6.SNMP Management..............................................................55
7.Product Specifications.......................................................57
Appendix A. Internet Explorer Setting ........................................................................59
Appendix B. VLAN Setting......................................................................................63
Appendix C. Technical Support and Service...............................................................68

6
1. Introduction
Welcome to the World of Switching-Network. In modern business
society, communication and information sharing are fundamental to
our lifestyle. Computer networks are one of the fastest means of
communication.
Congratulations on purchasing the Modular Switch. This Modular
Switch is a combination of 4-slot host cabinet and optional 4 kinds of
media modules. A maximum 32 x 10/100Base-TX switched ports
can be achieved using 4 x 8 port 10/100 Base-TX switch modules.
Modular Switch features store-and-forward switching scheme. Every
module has it’s own entry MAC address table to store source
address. The backplane of the Modular Switch can reach up to 10.4
Gbps as to improving network performance.
Figure 1-1 The Modular Switch
Modular Switch with layer 2 management functions, 4 expansion
slots can flexible configure your network. The 4 optional modules
can be 8-Port 10/100 Auto-sensing Intelligent Switch Module,
2/4/8-Port 100 Base-FX Intelligent Fiber Module, Gigabit
1000Base-T Intelligent Switch Modules, and Gigabit
1000Base-SX/LX Intelligent Fiber Modules.

7
With its build-in Web-based Management, managing and configuring
the Modular Switch becomes easier. From cabinet management to
port-level control and monitoring, you can visually configure and
manage your network via Web Browser. Just click your mouse
instead of typing cryptic command strings. However, the Modular
Switch can also be managed via Telnet, Console, or third-party
SNMP Management.
Key Features
 Conforms to IEEE 802.3, 802.3u, 802.3z, 802.3ab and
802.3x standards
 4 expansion slots to configure flexible network
 One built-in intelligent module with RS-232 console
port ( front side )
 Supports Half-duplex mode for backpressure, and
full-duplex for flow-control
 Store-and-Forward switching architecture for abnormal
packet filtering
 Up to 10.4Gbps Back-plane forwarding rate
 4K entry MAC address table per Intelligent switch
Module
 128Kbyts for 8 ports 10/100TX module, 4 Mbytes for
100FX Fiber module, 128Bytes for Gigabit module
 LED System Power, Diagnostic
8 ports TX module: 10/100Mbps,Link/Active,
Full-duplex/Collision;
2/4/8 ports Fiber module: Link/Active,
Full-duplex/Collision
Gigabit Module: Link, Active, Full-duplex, Collision
 Optional different modules including
Gigabit module ( SX/LX ), Gigabit 1000Base-T, 8-port
auto-sensing 10/100Base-TX switch module, 2/4-port
100BaseFX ( ST/SC/MT-RJ/VF-45 ) fiber module, 8-port
100BaseFX ( MT-RJ/VF-45 ) fiber module

8
Intelligent Module Features
 Web-Based Management
 SNMP Management
 Console and Telnet Management
 IEEE 802.1Q Tagging VLAN ( Up to 4095 VLANs )
 IEEE 802.1d Spanning Tree Protocol ( STP )
 Statistic Address Table for manual address-addition
 Port Trunking supported
 IGMP supported
 Broadcast Storm Filter
 Port Mirror
 Web Browser Security
 Firmware upgradeable trough TFTP
 MIB II and Private MIB supported
 IEEE 802.1p QoS, ToS
 Port Security
Management Methods
The Modular Switch supports following management methods :
 Console and Telnet Management
 Web-based Management
 SNMP Network Management
Console and Telnet Management
Console Management is done through the RS-232 Console Port.
Managing the Modular Switch in this method requires a direct
connection between PC and the Switch. While Telnet management
is done over the network. Once the Switch is on the network, you
can use Telnet to Log in and change the configuration.

9
Web-based Management
The Modular Switch provides an embedded HTML web site residing
in flash memory. It offers advanced management features and allow
users to manage the Modular Switch from anywhere on the network
through a standard browser such as Microsoft Internet Explorer. For
more information, See Section 5 Web-Based Management.
SNMP Network Management
SNMP ( Simple Network Management Protocol ) provides a means
to monitor and control network device, and to manage configurations,
statistic collection, performance, and security.
Data is passed from SNMP agents, which are hardware & software
processes reporting activity in each network device to the
workstation console used to oversee the network. The agent return
information contained in a MIB ( Management Information Base ),
which is a data structure that defines what is obtainable from the
device and what can be controlled.
Package Contents
Unpack the carton of the Modular Switch and verify them against the
checklist below.
 Modular Switch
 Power Cordially
 Four Rubber Feet
 RS-232 cable
 User Guide

10
Modular Switch Rubber Feet
Rack-mounted Kit RS-232 cable User Guide
Power Cord Figure 1-2. Package
Contents
Compare the contents of your Modular Switch package with the
standard checklist above. If any item is missing or damaged, please
contact your local dealer for service.
2. Product Overview
This section contains the following topics:
 Physical Description
 Optional Modules
 Installing Optional Modules
 Software Concepts

11
Physical Description
The physical dimensions of the HomePNA 312M are:
440mmx 227mm x 67mm ( Lx Wx H )
The Modular Switch is a modular unit, and its chassis contains four
slots. All optional models come with the built-in CPU modules. The
LEDs are located on the front panel of the Switch to allow you to
monitor the operation and performance at a glance. All ports can be
used for network configuration. The RS-232 port is used for
Out-of-Band Management.
Front & Rear Panel
The front panel of Modular Switch displayed in Figure 1-1 is shown
with 8-port 10/100Base-TX Module, 4-port 100Base-FX Fiber
Module and Gigabit 1000Base-T and Gigabit SX Fiber Module.
Figure 2-1. Front Panel
The 3-pronged power plug and On/off switched are located at the
Rear Panel of the Modular Switch displayed in Figure 2-2. The
Switch will work with AC in the range 100-240VAC, 50-60Hz.
F
igure 2-2.
R
ear Pane

12
LED Indicators
All LED status indicators are located on the FRONT panel of the
switch. They provide a real-time indication of system and operational
status. The ports for connections to other devices and networks are
also on the front panels.
LED Status Meaning
Power Green Power on
Diag Red Alert and problem notice
Green Device has been connected to the port
Blinks The data is transmitting on the port
LK/ACT
Off No device attached
Yellow Port in full duplex mode
Blinks A collision occurs on the port
FD/COL
Off No device attached or in half duplex mode
Green The Port is in 100Mbps mode
100
( Only for 8
port 10/100M
Switch Module )
Off Not connected or in 10 Mbps mode
Table 2-1. The above table provides descriptions of the LED status
and their meaning.
RS-232 Console
This Console port is used to connect a management station or
terminal with the switch. Out-of-band management means go
through the RS-232 port. For more information about switch
management, see Section 4 “ Connecting to the Network ”.

13
Software Concepts
Static Address
This feature allows you to enter the addresses that will not be aged
out. It can confine users on certain ports specified by the system
manager, so that they cannot switch to other ports.
Spanning Tree
Spanning Tree Protocol (STP) is an industry standard that prevents
loops configurations in switched networks. The Spanning Tree
algorithm creates a single path through network by making sure that
if more than one path exists between parts of a network, only one of
those paths is used.
This also permits multiple interswitch links to remain active for data
transport while operating in conjunction with the Spanning Tree
algorithm. The IEEE 802.1d Spanning Tree Protocol support for
redundant backbone connections and loop-free networks simplifies
network configuration and improves fault tolerance.
Virtual LANs ( VLANs )
A VLAN is a group of switch ports designated by the switch as
belonging to the same broadcast domain.
This feature allows workgroups to be defined on the basis of their
logical function instead of their physical location, and does not
require recabling. It also enables you to configure port-based VLANs
to help isolate broad- cast traffic and increase security, so as to
increase bandwidth to each station.
VLAN also helps you create limited broadcast domains, to prevent
traffic from being forwarded to stations where it is not needed.
Port Trunking
Port Trunking allows you to build higher bandwidth connections by

14
aggregate several ports into one single group.
Additionally, it may be more cost-effective to trunk multiple lower
speed links than to underutilize a gigabit port. Available copper links
and supported distances are more pervasive for lower speed links.
For example, 100Mbps NICs and switch ports are less expensive
than 1Gbps equipment.
Port trunking also allows end users to protect their investment in
existing infrastructure by reusing current equipment.
SNMP
( Simple Network Management Protocol ) A widely-used network
monitoring and control protocol. Data is passed from SNMP agents,
which are hardware and/or software processes reporting activity in
each network device ( hub, router, bridge, etc. ) to the workstation
console used to oversee the network. The agents return information
contained in a MIB ( Management Information Base ), which is a
data structure that defines what is obtainable from the device and
what can be controlled ( turned off, on, etc.). Originating in the UNIX
community, SNMP has become widely used on all major platforms.
Port Mirror
Port mirror allows user to define a destination port and a target port ,
all the packet on the target port will be copy and resend to
destination port, it make user can monitor the packet and won’t
effect the bandwidth of target port.
IGMP
Internet Group Multicast Protocol (IGMP) is used to support
real-time applications such as video conferencing or streaming
audio. IGMP allow you to query for any attached hosts who want to
receive a specific multicast service. The switch looks up the IP
Multicast Group used for this service and adds any port which

15
received a similar request to that group. It then propagates the
service request on to any neighboring multicast switch to ensure
that it will continue to receive the multicast service.
Port Security
Port Security allow you to restrict specific MAC addresses to reside
in some port. The mean is only packet that with pre-defined MAC
address will be received by the port. It allows user by manual input
the MAC address table.
Priority
There are two priority queues ( high and low ) on each port. Each
port arbitrates between two transmit queues ( high and low priority ).
The arbitration uses weighted round-robin between the high and low
priority queues, and you can adjust this weight.
Broadcast Storm Filter
Storm Filter can avoid any flooded data packets. This feature
prevents the bursts of broadcast traffic. Excessive broadcast
packets ( Broadcast Storms ) can be filtered in our managed switch
by enabling the "Broadcast Storm Filtering" option.

16
3. Network Configuration
This chapter provides 3 network configuration examples by using
the Modular Switch:
 Collapsed Backbone Application
 Departmental Bridge Application
 Virtual LAN (VLAN)Application
The switch provides versatile configuration options for the network. It
is ideally suited as a workgroup or segment switch in a network; it
aggregate traffic from workgroup switches, or provide dedicated
100Mbps to servers with bandwidth-intensive applications. And
because all Fast Ethernet ports auto-negotiate for operation at 100
Mbps or 1000Mbps ( Gigabit ) the switch is perfectly suited to an
evolving network environment where demand for network speed is
increasing.
Collapsed BackboneApplication
For small network where substantial growth can be expected in the
near future, this switch is an ideal solution supporting backbone
connectivity.
The switch can be used as a standalone switch for a group of heavy
traffic users. Switching is brought to the desktop either through a
single end-station per switch port or through a multi-port hub.
A 100 Mbps server is connected to a port, providing end stations
high-speed accessibility to its applications. This configuration
provides dedicated 100 Mbps connections to the network center, to
the server, and the most up to 24 users.
When the network needs expansion, you can simply daisy-chain the
switch to any IEEE 802.3 ( Ethernet ), IEEE 802.3u ( Fast Ethernet ),

17
IEEE 802.3z ( Gigabit Ethernet ) compliant hub. This switch can also
cooperate with a wide range of networking devices (e.g., firewall
routers and printer servers) added to the network.
Figure 3-1. Collapsed Backbone Application
Departmental Bridge
For enterprise networks where large data broadcasts are constantly
processed, this switch is an ideal solution for department users to
connect to the corporate backbone. The Modular Switch used as
segment switch can alleviate user contention for bandwidth and
eliminate server and network bottlenecks. All ports can connect to
high-speed department servers that need high bandwidth. This
switch provides parallel communications between each of its ports,
which can run up to 200 or 2000Mbps at full duplex.
The Switch makes key servers available to more users by allowing
multiple conversations to occur concurrently, thereby significantly
expanding overall network throughput. Moreover, this switch eases
supervision and maintenance by allowing network manager
centralize multiple servers in a single location.

18
Figure 3-2. Departmental Bridge Application
NOTE: Full-duplex operation only applies to point-to-point access
(for example, when attaching the switch to a workstation, server, or
another switch). When connecting to hubs, use a standard cascaded
connection set for half-duplex operation.
IEEE 802.1Q VLAN Application
The switch support up to 4095 port-based 802.1Q-compatible virtual
LANs (VLANs).
Port-based VLAN Workgroup
You can group the switch ports into broadcast domains by assigning
them to the same VLAN to increase network capacity and
performance. With network segmentation, each switch port connects

19
to a segment that is a single broadcast domain. Packets received in
one VLAN can only be forwarded within that VLAN.
VLAN allows the grouping of end stations logically, based not on
physical location but on business policies such as job function or
department. Members of a group can be dispersed throughout a
facility - they do not have to be connected in close physical
locations.
Hence, group members can coordinate their data communication
requirements regardless of the actual working locations; and the
logical network can extend to any point you want it to. Moreover,
VLAN groups can be modified at any time to add, move or change
users without any re-cabling.
Figure 3-3. VLAN Workgroup Application
Shared Server
The switch compliant to the IEEE802.1Q tagging VLAN standard
allows ports to exist in multiple VLANs for shared resources, such as
servers, printers, and switch-to-switch connections. It is also
possible to have resources exist in multiple VLANs on one switch as
shown in the following figure.

20
Figure 3-4. Shared Server
In this example, stations on different VLANs share resources. As a result,
VLAN 1 and VLAN 2 can access VLAN 3 for printing. The broadcasts
from ports configured in VLAN3 can be seen by all VLAN port members
of VLAN3.
4. Connecting to the Network
This chapter provides the installation procedure and instructions for
assigning IP address. This chapter contains following topics:
 Pre-instruction requirements
 Mounting the switch
 Connecting to the switch
 Assigning IP address
Pre-Installation Requirements
Before you start hardware installation, make sure your installation
environment has below items: