SMC Networks EliteConnect SMCE21011 User manual

USER GUIDE
EliteConnectTM SMCE21011
802.11b/g/n AP
SMCE21011

20 Mason
Irvine, CA 92618
Phone: [phone]
EliteConnectTM SMCE21011
User Guide
April 2009
Pub. # XXXXXXXXXXX
E042009-DT-R01

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable.
However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or
other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications
at any time without notice.
Copyright © 2009 by
SMC Networks, Inc.
20 Mason
Irvine, CA 92618
All rights reserved
Trademarks:
SMC is a registered trademark; and EZ Switch, TigerStack, TigerSwitch, and TigerAccess are
trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered
trademarks of their respective holders.

– 4 –
LIMITED WARRANTY
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its
products to be free from defects in workmanship and materials, under
normal use and service, for the applicable warranty term. All SMC products
carry a standard 90-day limited warranty from the date of purchase from
SMC or its Authorized Reseller. SMC may, at its own discretion, repair or
replace any product not operating as warranted with a similar or
functionally equivalent product, during the applicable warranty term. SMC
will endeavor to repair or replace any product returned under warranty
within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime*
warranty by registering new products within 30 days of purchase from SMC
or its Authorized Reseller. Registration can be accomplished via the
enclosed product registration card or online via the SMC Web site. Failure
to register will not affect the standard limited warranty. The Limited
Lifetime warranty covers a product during the Life of that Product, which is
defined as the period of time during which the product is an “Active” SMC
product. A product is considered to be “Active” while it is listed on the
current SMC price list. As new technologies emerge, older technologies
become obsolete and SMC will, at its discretion, replace an older product in
its product line with one that incorporates these newer technologies. At
that point, the obsolete product is discontinued and is no longer an “Active”
SMC product. A list of discontinued products with their respective dates of
discontinuance can be found at:
http://www.smc.com/index.cfm?action=customer_service_warranty .
All products that are replaced become the property of SMC. Replacement
products may be either new or reconditioned. Any replaced or repaired
product carries either a 30-day limited warranty or the remainder of the
initial warranty, whichever is longer. SMC is not responsible for any custom
software or firmware, configuration information, or memory data of
Customer contained in, stored on, or integrated with any products returned
to SMC pursuant to any warranty. Products returned to SMC should have
any customer-installed accessory or add-on components, such as
expansion modules, removed prior to returning the product for
replacement. SMC is not responsible for these items if they are returned
with the product.
Customers must contact SMC for a Return Material Authorization number
prior to returning any product to SMC. Proof of purchase may be required.
Any product returned to SMC without a valid Return Material Authorization
(RMA) number clearly marked on the outside of the package will be
returned to customer at customer’s expense. For warranty claims within
North America, please call our toll-free customer support number at (800)
762-4968. Customers are responsible for all shipping charges from their
facility to SMC. SMC is responsible for return shipping charges from SMC to
customer.
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR
REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN

– 5 –
LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME
FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,
INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL
NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES
NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S
MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND
THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING,
OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT
OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS,
OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH
THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE,
OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED
RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES
OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR
CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS
WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance
from the active SMC price list. Under the limited lifetime warranty, internal
and external power supplies, fans, and cables are covered by a standard
one-year warranty from date of purchase.
SMC Networks, Inc.
20 Mason
Irvine, CA 92618

– 6 –

– 7 –
COMPLIANCES
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
◆Reorient or relocate the receiving antenna
◆Increase the separation between the equipment and receiver
◆Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
◆Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
This device is going to be operated in 5.15~5.25GHz frequency range, it is
restricted in indoor environment only.

A BOUT T HIS G UIDE
– 8 –
IMPORTANT NOTE:
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator & your body.
IC STATEMENT :
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe B conforme á la norme NMB-003 du
Canada.
To reduce potential radio interference to other users, the antenna type and
its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p) is not more than that permitted for successful
communication.
This device has been designed to operate with the antennas listed below,
and having a maximum gain of [5] dB. Antennas not included in this list or
having a gain greater than [5] dB are strictly prohibited for use with this
device. The required antenna impedance is 50 ohms.
The device could automatically discontinue transmission in case of absence
of information to transmit, or operational failure. Note that this is not
intended to prohibit transmission of control or signaling information or the
use of repetitive codes where required by the technology.
The device for the band 5150-5250 MHz is only for indoor usage to reduce
potential for harmful interference to co-channel mobile satellite systems.
The maximum antenna gain permitted (for devices in the band 5725-5825
MHz) to comply with the e.i.r.p. limits specified for point-to-point and non
point-to-point operation as appropriate, as stated in section A9.2(3).
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed
and operated with minimum distance 20 cm between the radiator & your
body.

A BOUT T HIS G UIDE
– 9 –
AUSTRALIA/NEW ZEALAND AS/NZS 4771
JAPAN VCCI CLASS B
TAIWAN NCC
根據交通部低功率管理辦法規定：
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更
頻率、加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應
立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通
信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
EC CONFORMANCE DECLARATION
Marking by the above symbol indicates compliance with the Essential
Requirements of the R&TTE Directive of the European Union (1999/5/EC).
This equipment meets the following conformance standards:
◆EN 60950-1 (IEC 60950-1) - Product Safety
◆EN 301 893 - Technical requirements for 5 GHz radio equipment
◆EN 300 328 - Technical requirements for 2.4 GHz radio equipment
◆EN 301 489-1 / EN 301 489-17 - EMC requirements for radio
equipment
This device is intended for use in the following European Community and
EFTA countries:
Requirements for indoor vs. outdoor operation, license requirements and
allowed channels of operation apply in some countries as described below:
◆Austria ◆Belgium ◆Cyprus ◆Czech Republic ◆Denmark
◆Estonia ◆Finland ◆France ◆Germany ◆Greece
◆Hungary ◆Iceland ◆Ireland ◆Italy ◆Latvia
◆Liechtenstein ◆Lithuania ◆Luxembourg ◆Malta ◆Netherlands
◆Norway ◆Poland ◆Portugal ◆Slovakia ◆Slovenia
◆Spain ◆Sweden ◆Switzerland ◆United Kingdom ◆
ACN 066 352010

A BOUT T HIS G UIDE
– 10 –
◆In Italy the end-user must apply for a license from the national
spectrum authority to operate this device outdoors.
◆In Belgium outdoor operation is only permitted using the 2.46 - 2.4835
GHz band: Channel 13.
◆In France outdoor operation is only permitted using the 2.4 - 2.454 GHz
band: Channels 1 - 7.
N OTE : The user must use the configuration utility provided with this
product to ensure the channels of operation are in conformance with the
spectrum usage rules for European Community countries as described
below.
◆This device requires that the user or installer properly enter the current
country of operation in the command line interface as described in the
user guide, before operating this device.
◆This device will automatically limit the allowable channels determined
by the current country of operation. Incorrectly entering the country of
operation may result in illegal operation and may cause harmful
interference to other systems. The user is obligated to ensure the
device is operating according to the channel limitations, indoor/outdoor
restrictions and license requirements for each European Community
country as described in this document.
◆This device employs a radar detection feature required for European
Community operation in the 5 GHz band. This feature is automatically
enabled when the country of operation is correctly configured for any
European Community country. The presence of nearby radar operation
may result in temporary interruption of operation of this device. The
radar detection feature will automatically restart operation on a channel
free of radar.
◆The 5 GHz Turbo Mode feature is not allowed for operation in any
European Community country. The current setting for this feature is
found in the 5 GHz 802.11a Radio Settings Window as described in the
user guide.
◆The 5 GHz radio's Auto Channel Select setting described in the user
guide must always remain enabled to ensure that automatic 5 GHz
channel selection complies with European requirements. The current
setting for this feature is found in the 5 GHz 802.11a Radio Settings
Window as described in the user guide.
◆This device is restricted to indoor use when operated in the European
Community using the 5.15 - 5.35 GHz band: Channels 36, 40, 44, 48,
52, 56, 60, 64. See table below for allowed 5 GHz channels by country.
◆This device may be operated indoors or outdoors in all countries of the
European Community using the 2.4 GHz band: Channels 1 - 13, except
where noted below.

A BOUT T HIS G UIDE
– 11 –
◆In Italy the end-user must apply for a license from the national
spectrum authority to operate this device outdoors.
◆In Belgium outdoor operation is only permitted using the 2.46 -
2.4835 GHz band: Channel 13.
◆In France outdoor operation is only permitted using the 2.4 - 2.454
GHz band: Channels 1 - 7.
OPERATION USING
5 GHZCHANNELS IN THE EUROPEAN COMMUNITY
The user/installer must use the provided configuration utility to check the
current channel of operation and make necessary configuration changes to
ensure operation occurs in conformance with European National spectrum
usage laws as described below and elsewhere in this document.
DECLARATION OF CONFORMITY IN LANGUAGES OF THE EUROPEAN
COMMUNITY
Allowed Frequency Bands Allowed Channel Numbers Countries
5.15 - 5.25 GHz* 36, 40, 44, 48 Austria, Belgium
5.15 - 5.35 GHz* 36, 40, 44, 48, 52, 56, 60, 64 France, Switzerland,
Liechtenstein
5.15 - 5.35* & 5.470 - 5.725 GHz 36, 40, 44, 48, 52, 56, 60, 64, 100,
104, 108, 112, 116, 120, 124, 128,
132, 136, 140
Denmark, Finland, Germany,
Iceland, Ireland, Italy,
Luxembourg, Netherlands,
Norway, Portugal, Spain,
Sweden, U.K.
5 GHz Operation Not Allowed None Greece
* Outdoor operation is not allowed using 5.15-5.35 GHz bands (Channels 36 - 64).
Czech
Estonian
Eesti
Käesolevaga kinnitab SMC seadme Radio LAN vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English Hereby, SMC, declares that this Radio LAN device is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Finnish
Suomi
Valmistaja SMC vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/
5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Dutch
Nederlands
Hierbij verklaart SMC dat het toestel Radio LAN device in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG
Bij deze SMC dat deze Radio LAN device voldoet aan de essentiële eisen en aan de
overige relevante bepalingen van Richtlijn 1999/5/EC.
French
Français
Par la présente SMC déclare que l'appareil Radio LAN device est conforme aux
exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE

A BOUT T HIS G UIDE
– 12 –
Swedish
Svenska
Härmed intygar SMC att denna Radio LAN device står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv
1999/5/EG.
Danish
Dansk
Undertegnede SMC erklærer herved, at følgende udstyr Radio LAN device overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF
German
Deutsch
Hiermit erklärt SMC, dass sich dieser/diese/dieses Radio LAN device in
Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten
Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)
Hiermit erklärt SMC die Übereinstimmung des Gerätes Radio LAN device mit den
grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie
1999/5/EG. (Wien)
Greek
ελληνικά
Με την παρουσα SMC δηλωνει οτι radio LAN device συμμορφωνεται προσ τισ ουσιωδεισ
απαιτησεισ και τισ λοιπεσ σΧετικεσ διαταξεισ τησ οδηγιασ 1999/5/εκ
Hungarian
Magyar
Alulírott, SMC nyilatkozom, hogy a Radio LAN megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Italian
Italiano
Con la presente SMC dichiara che questo Radio LAN device è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latvian
Latviski
Lithuanian
Maltese
Malti
Spanish
Español
Por medio de la presente SMC declara que el RadioLANdevice cumpleconlos requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/
5/CE
Polish
Polski
Portuguese
Português
SMC declara que este Radio LAN device está conforme com os requisitos essenciais e
outras disposições da Directiva 1999/5/CE.
Slovak
Slovensky
Slovenian
Slovensko
SMC izjavlja, da je ta Radio LAN v skladu z bistvenimi zahtevami in ostalimi relevantnimi
doloili direktive 1999/5/ES.

– 13 –
ABOUT THIS GUIDE
PURPOSE This guide gives specific information on how to install the 11n wireless
access point and its physical and performance related characteristics. It
also gives information on how to operate and use the management
functions of the access point.
AUDIENCE This guide is intended for use by network administrators who are
responsible for installing, operating, and maintaining network equipment;
consequently, it assumes a basic working knowledge of LANs (Local Area
Networks), the Internet Protocol (IP), and Simple Network Management
Protocol (SNMP).
CONVENTIONS The following conventions are used throughout this guide to show
information:
N OTE : Emphasizes important information or calls your attention to related
features or instructions.
C AUTION : Alerts you to a potential hazard that could cause loss of data, or
damage the system or equipment.
W ARNING : Alerts you to a potential hazard that could cause personal injury.
RELATED PUBLICATIONS As part of the access point’s software, there is an online web-based help
that describes all management related features.
REVISION HISTORY This section summarizes the changes in each revision of this guide.
MARCH 2009 REVISION
This is the first revision of this guide.

– 14 –
CONTENTS
LIMITED WARRANTY 4
COMPLIANCES 7
ABOUT THIS GUIDE 13
CONTENTS 14
FIGURES 19
TABLES 21
INDEX OF CLI COMMANDS 23
SECTION I GETTING STARTED 26
1INTRODUCTION 27
Key Hardware Features 27
Description of Capabilities 27
Package Contents 28
Hardware Description 29
Antennas 30
External Antenna Connector 30
LED Indicators 32
Console Port 33
Ethernet Port 33
Power Connector 33
Reset Button 34
2NETWORK TOPOLOGIES 35
Interference Issues 35
Infrastructure Wireless LAN 35
Infrastructure Wireless LAN for Roaming Wireless PCs 36
Infrastructure Wireless Bridge 37

C ONTENTS
– 15 –
3INSTALLING THE ACCESS POINT 39
Location Selection 39
Mounting on a Horizontal Surface 40
Mounting on a Wall 41
Connecting and Powering On 42
4INITIAL CONFIGURATION 43
Connecting to the Login Page 43
Home Page and Main Menu 44
Common Web Page Buttons 45
Quick Start 46
Step 1 46
Step 2 47
Step 3 49
Main Menu Items 50
SECTION II WEB CONFIGURATION 51
5SYSTEM SETTINGS 52
Administration Settings 52
IP Address 54
Radius Settings 55
Primary and Secondary RADIUS Server Setup 56
RADIUS Accounting 58
System Time 58
SNTP Server Settings 59
Time Zone Setting 59
Daylight Saving Settings 60
SpectraLink Voice Priority 60
VLAN Configuration 60
System Logs 62
Quick Start Wizard 64
6MANAGEMENT SETTINGS 65
Remote Management Settings 65
Access Limitation 67
Simple Network Management Protocol 68

C ONTENTS
– 16 –
SNMP Basic Settings 68
SNMP Trap Settings 70
View Access Control Model 71
SNMPv3 Users 73
SNMPv3 Targets 74
SNMPv3 Notification Filters 74
7ADVANCED SETTINGS 76
Local Bridge Filter 76
Link Layer Discovery Protocol 77
Access Control Lists 78
Source Address Settings 78
Destination Address Settings 79
Ethernet Type 80
8WIRELESS SETTINGS 82
Spanning Tree Protocol (STP) 82
Bridge 83
Ethernet Interface 84
Wireless Interface 85
Authentication 85
Local Authentication 85
RADIUS MAC Authentication 87
Interface Mode 88
Radio Settings 89
Virtual Access Points (VAPs) 93
VAP Basic Settings 94
WDS-STA Mode 95
Wireless Security Settings 95
Wired Equivalent Privacy (WEP) 97
QoS 99
9MAINTENANCE SETTINGS 103
Upgrading Firmware 103
Running Configuration 106
Resetting the Access Point 107
10 STATUS INFORMATION 109
AP Status 109

C ONTENTS
– 17 –
AP System Configuration 109
AP Wireless Configuration 111
Station Status 112
System Logs 112
SECTION III COMMAND LINE INTERFACE 114
11 USING THE COMMAND LINE INTERFACE 116
Console Connection 116
Telnet Connection 117
Entering Commands 118
Keywords and Arguments 118
Minimum Abbreviation 118
Command Completion 118
Getting Help on Commands 118
Showing Commands 118
Negating the Effect of Commands 119
Using Command History 119
Understanding Command Modes 119
Exec Commands 120
Configuration Commands 120
Command Line Processing 121
12 GENERAL COMMANDS 122
13 SYSTEM MANAGEMENT COMMANDS 127
System Management Commands 127
14 SYSTEM LOGGING COMMANDS 143
15 SYSTEM CLOCK COMMANDS 148
16 DHCP RELAY COMMANDS 152
17 SNMP COMMANDS 154
18 FLASH/FILE COMMANDS 167
19 RADIUS CLIENT COMMANDS 170
20 802.1X AUTHENTICATION COMMANDS 175

C ONTENTS
– 18 –
21 MAC ADDRESS AUTHENTICATION COMMANDS 177
22 FILTERING COMMANDS 181
23 SPANNING TREE COMMANDS 186
24 WDS BRIDGE COMMANDS 193
25 ETHERNET INTERFACE COMMANDS 195
26 WIRELESS INTERFACE COMMANDS 201
27 WIRELESS SECURITY COMMANDS 218
28 LINK LAYER DISCOVERY COMMANDS 228
29 VLAN COMMANDS 232
30 WMM COMMANDS 235
SECTION IV APPENDICES 240
ATROUBLESHOOTING 241
Diagnosing LED Indicators 241
Before Contacting Technical Support 241
BHARDWARE SPECIFICATIONS 244
CC
ABLES AND PINOUTS 247
Twisted-Pair Cable Assignments 247
10/100BASE-TX Pin Assignments 248
Straight-Through Wiring 248
Crossover Wiring 249
1000BASE-T Pin Assignments 250
Cable Testing for Existing Category 5 Cable 250
Adjusting Existing Category 5 Cabling to Run 1000BASE-T 250
Console Port Pin Assignments 251
GLOSSARY 252
INDEX 256

– 19 –
FIGURES
Figure 1: Top Panel 29
Figure 2: Rear Panel 29
Figure 3: Ports 30
Figure 4: External Antenna Connector 31
Figure 5: Screw-off External Antenna Connector - Close Up 31
Figure 6: LEDs 32
Figure 7: Infrastructure Wireless LAN 36
Figure 8: Infrastructure Wireless LAN for Roaming Wireless PCs 37
Figure 9: Bridging Mode 38
Figure 10: Attach Feet 40
Figure 11: Wall Mounting 41
Figure 12: Login Page 43
Figure 13: Home Page 44
Figure 14: Set Configuration Changes 45
Figure 15: Help Menu 45
Figure 16: Quick Start - Step 1 46
Figure 17: Quick Start - Step 2 47
Figure 18: Quick Start - Step 3 49
Figure 19: Administration 53
Figure 20: Set DNS Address 54
Figure 21: TCP/IP Settings 54
Figure 22: Invalid DNS 55
Figure 23: RADIUS Settings 57
Figure 24: SNTP Settings 59
Figure 25: SVP Settings 60
Figure 26: Setting the VLAN Identity 62
Figure 27: System Log Settings 63
Figure 28: Remote Management 66
Figure 29: Access Limitation 67
Figure 30: SNMP Basic Settings 69
Figure 31: SNMP Trap Settings 70

F IGURES
– 20 –
Figure 32: SNMP VACM 71
Figure 33: Configuring SNMPv3 Users 73
Figure 34: SNMPv3 Targets 74
Figure 35: SNMP Notification Filter 75
Figure 36: Local Bridge Filter 76
Figure 37: LLDP Settings 77
Figure 38: Source ACLs 79
Figure 39: Destination ACLs 79
Figure 40: Ethernet Type Filter 81
Figure 41: Spanning Tree Protocol 83
Figure 42: Local Authentication 86
Figure 43: RADIUS Authentication 87
Figure 44: Interface Mode 88
Figure 45: Radio Settings 90
Figure 46: VAP Settings 93
Figure 47: VAP Basic Settings 94
Figure 48: WDS-STA Mode 95
Figure 49: Configuring VAPs - Common Settings 96
Figure 50: WEP Configuration 98
Figure 51: WMM Backoff Wait Times 100
Figure 52: QoS 101
Figure 53: Firmware 104
Figure 54: Running Configuration File 106
Figure 55: Resetting the Access Point 107
Figure 56: AP System Configuration 110
Figure 57: AP Wireless Configuration 111
Figure 58: Station Status 112
Figure 59: System Logs 112
Figure 60: RJ-45 Connector 247
Figure 61: Straight Through Wiring 249
Figure 62: Crossover Wiring 249
Figure 63: DB-9 Connector 251