Smeg PUM60X User manual

PUM60X & PUM90X
RANGE HOOD
INSTRUCTION MANUAL
Thank you for your purchase of this product. Please read the
manual carefully before operating the appliance.

Installation Diagram
Warning: Before cleaning, please ensure that the power is
switched off by detaching the plug from the wall socket.
10.1 Clean the surface of hood every week with mild soap
or detergent . Avoid solvents, acid, alkali, scouring pads
or powders that could irreparably damage the stainless
steel surface.
10.2 The grease filters may be washed using mild soap,
detergent or degreasing agent.
10.3 Charcoal filters cannot be cleaned and must be gen-
erally replaced after 6 months of use.
Cleaning & Maintenance

Power Supply 220V~240V 50Hz
Rated Input Power 140W
Lighting Power 2W×1
Motor Power 138W
Airflow ≥700m³/h
Outlet Diameter 150mm
Specifications
Power Supply 220V~240V 50Hz
Rated Input Power 142W
Lighting Power 2W×2
Motor Power 138W
Airflow ≥700m³/h
Outlet Diameter 150mm
PUM60X
PUM90X
Introduction………………………….1
Features……………………………...2
Installation………………………......2
How To Use…………………………..4
Lamp Change……………………..…5
Safety Information………………….6
Trouble Shooting………………..….7
Electrical Diagram……………..…..8
Specifications……………………….9
Cleaning & Maintenance………….10
Contents

1.1 This appliance has been manufactured with materials
and processes that respect the environment. We hope that
you will continue this important consideration in the opera-
tion of this appliance & the disposal of the packaging mate-
rials, thank you.
1.2 The installation work must be undertaken by a qualified
technician experienced in cooker hood installation. Please
connect the correct power rating (see page 6).
1.3 The manufacturer disclaims all liability for any damage
or injury caused as a result of not following the instructions
for installation contained in the following text.
1.4 The appliance is not intended for use by young children
or infirm persons without supervision.
1.5 Young children should be supervised to ensure that they
do not play with the appliance.
1.6 The maximum number of hobs covered by range hood
should not exceed 5.
1.7 Any modifications to the appliance, electric wire and
plug is dangerous & voids the warranty.
Introduction
PUM60X
PUM90X
Electrical Diagram

If any problem occurs, please detach the plug from the
socket and contact the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
Problem Cause Solution
Light on, but motor
does not work
The outlet valve is blocked Detach flue and duct then
turn on the hood to check if
the valve opens
The capacitor has failed Call for technical service
The control switch has failed Call for technical service
Light does not work,
motor does not work
No power supply Plug another appliance into
the socket to confirm there is
power supply
Vibration The propeller is damaged or
unbalanced
Call for technical service
The hood is not installed cor-
rectly
Review the installation in-
structions & check the instal-
lation again for loose screws,
brackets or connections
Insufficient suction
effect
The distance between the hood
and the cooker is too far
Check that the distance is
between 650mm to 700mm
The filters are saturated Clean the filters from grease
residue and replace after
drying.
Troubleshooting
2.1 This appliance is manufactured from top quality materials,
and offers superb streamlined operation.
2.2 With high suction power and low noise, it is designed to
remove cooking fumes from your kitchen quietly & effectively.
3.1 The range hood should be mounted at a distance of 650-
750mm from the cooking surface for safety & optimum per-
formance (If the instructions for installation of the gas hob spec-
ify a greater distance, this has to be taken into account.) (see
pic1). That exhaust air must not be discharged into a flue which
is used for exhausting fumes from other appliances burning gas
or other fuels.
3.2 To install, drill 2 holes of Ø8mm on a
sturdy wall and in line with the hood.
3.3 Insert expending screws into the holes.
3.4 Fix drilling template on the wall (see pic
2).
3.5 The appliance should be embedded into
the wall unit or another support. This process
should be carried out by 4 screws（provide
with hood）suitable for the kind of unit fol-
lowing the instructions for the drilling of the holes
as shown in (see pic 3).
3.6 Attach the duct to the one way valve, and connect it to the
Features
Installation（duct is not supplied)
pic 1

3.7 Ensure that the wall to be installed on is sufficiently
sturdy to carry the weight of the hood. It should be
mounted level for best performance (see illustration).
3.8 Do not connect to a common vent with other appliance
such as gas heater, water heater, laundry dryer etc.
3.9 The duct should not be bent more than ≥120°from the
one way valve outlet to the kitchen vent.
3.10 Check to make sure that the electric cord is not in con-
tact with sharp edges of the appliance.
3.11 Be sure that the plug is accessible after installation.
pic 2
\\
pic 3
\\
pic 4
\\
pic 5
\\
◆There must permanent & adequate ventilation of the room
when operating the range hood with appliances burning
gas or other fuels.
◆Do not check the status of the filters when the range hood
is operating, wait at least 30 minutes after switching off to
avoid scalding.
◆Do not touch the light within 30 minutes after appliance
use.
◆Avoid operating a gas cooker when there is no pan on the
stove, it is a fire hazard and may cause damage to the
hood filters.
◆Disconnect the electrical plug prior to any maintenance.
◆This appliance is not intended for use by young children
and persons unless they have been adequately supervised
by a responsible person to ensure that they can use the
appliance safely.
◆The range hood is for home use only and is not suitable
for outdoor, barbecue, and other commercial applications.
◆The range hood and its filter should be cleaned regularly
for best performance.
◆Before cleaning, please confirm that the power is
switched off.
◆Building regulations concerning the discharge of exhaust
air have to be fulfilled.
◆Don’t cook with an open flame under the range hood.
◆For any technical issues ensure that a suitably qualified
person effects any repairs or inspection.
Safety Information

As with any maintenance on the appliance, first turn off the
power supply by unplugging from the wall socket.
1.Remove the filters from the appliance.
2.Unload the screws on the stainless steel hood panel.
3.Remove the stainless steel panel before changing the lamp
(see pic 7).
4.Change the lamp (LED Lamp Max.2W) and then reinstall
in the reverse manner.
pic 7
Lamp Change
3 Speed
3 Speed adjustment
adjustment
adjustment ( (see
see
see pic 6). pic 6).
◆Push Stop button, and the motor will stop.
◆Push the Low button, and the motor runs at low
speed.
◆Push the Mid button, and the motor runs at mid. speed.
◆Push the High button, and the motor runs at high
speed.
◆Push the Light button, and the two lighting lamps illu-
minate. Push it again and the lamp will turn off.
◆On any speed, push “T” & the delay timer will switch
off the hood after 5 minutes.
pic 6
How To Use