Smithco DIESEL SUPER RAKE User manual

PARTS & SERVICE
MANUAL
DIESEL SUPER RAKE
Model 17-001-C Bunker Rake
Starting Serial #2636 December, 2002
SMITHCO PRODUCT SUPPORT
1-800-891-9435
Hwy SS and Poplar Avenue, Cameron WI 54822
E-mail: [email protected]

Introduction Service Diagrams Parts Accessories Reference
Accessories ....................................50-101
13-680HydraulicPlowwith Lift ................... 50-53
13-679Hydraulic Plowwith Lift ................... 50-53
13-7303-Bank HydraulicValve.................... 54-55
13-644ManualPlow ................................... 56-59
13-678 Castor Wheel Kit............................ 60-61
13-107Scarifier withChisel Blades............. 62-63
13-577Scarifier Vertical Blades .................. 64-65
13-116SandCultivator ................................ 66-67
13-199 EdgerKit........................................ 68-69
13-111Drag MatKit .................................... 70-71
42-026 84”SSTournamentRake ............... 72-75
42-128 72”SSTournamentRake ............... 76-79
13-438 RakeAssembly............................ 780-81
13-606 RakeAssembly (Lexan) ................. 82-83
13-684 BrushKit for13-438 and13-606 ..... 84-85
13-298Fan RakeAttachment ..................... 86-87
13-319 Fan Rake Kit.................................. 86-87
26-007 ProfessionalInfield Finisher ............. 88-89
26-008FlexAction FieldFinisher................ 90-93
34-191BoxGrader...................................... 94-97
42-582Spiker.............................................. 98-99
42-586SpikerMainFrame ...................... 100-101
Reference......................................103-104
Decal List ...................................................... 103
QuickReference ReplacementParts ............. 104
Warranty..................................InsideBackCover
CONTENTS
Introduction .......................................... 1-4
Introduction........................................................1
Safe Practices ...................................................2
Specifications .................................................... 3
OptionalEquipment ...........................................4
Service ................................................ 5-11
Maintenance ................................................... 5-7
ServiceChart .....................................................8
EndUser’s ServiceChart ...................................9
Adjustments ............................................... 10-11
Storage ............................................................ 11
Diagrams...........................................12-15
Wiring Diagram ........................................... 12-13
HydraulicDiagram ...................................... 14-15
Parts ..................................................16-49
MainFrame ................................................ 16-19
AcceleratorLinkage .................................... 20-21
RightFender andEngine ............................ 22-23
LeftFenderandTank .................................. 24-25
ThreeWheel DriveFrontFork ..................... 26-27
Engineand Pump ....................................... 28-31
RearAxle.................................................... 32-33
HydraulicOilFilter ...................................... 34-35
HydraulicOil Tank....................................... 34-35
RearRake Lift............................................. 36-37
On-OffValve................................................ 38-39
13-7292-Bank HydraulicValve.................... 40-41
13-110Variable Pump ................................. 42-43
13-032Front WheelMotor(4.9C.I.)............ 44-45
13-615Rear WheelMotor (7.5C.I.)............. 46-47
LiftAssembly.............................................. 48-49

1
Informationneededwhen orderingreplacement parts:
1. Model Numberof machine
2. Serial Number of machine
3. Name and Part Number of part
4. Quantity ofparts
INTRODUCTION
Thankyoufor purchasinga product.
Readthismanual andall other manualspertaining tothe Diesel SuperRake carefullyasthey havesafety, oper-
ating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment
damage.
Keepmanuals inasafe placeafter operatorand maintenancepersonnel haveread them.Rightandleftsides are
fromthe operator’sseat, facingforward.
All machineshave aSerial Numberand ModelNumber.Bothnumbersare neededwhen ordering
parts. The serial number plate on the Diesel Super Rake is located on the right side main frame. Refer to engine
manual for placement of engine serial number.
For easy access record your Serial and Model numbers here.

2
Introduction
SAFE PRACTICES
1. It is your responsibility to read this manual and all publications associated with this machine (engine,
accessoriesand attachments).
2. Never allow anyone to operate or service the machine or its attachments without proper training and
instructions.Never allowminorsto operateany equipment.
3. Learn the proper use of the machine, the location and purpose of all the controls and gauges before you
operate the equipment. Working with unfamiliar equipment can lead to accidents.
4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,
hands and feet. Operate the machine only in daylight or in good artificial light.
5. Inspect the area where the equipment will be used. Pick up all debris you can find before operating.
Beware of overhead obstructions and underground obstacles. Stay alert for hidden hazards.
6. Never operate equipment that is not in perfect working order or without decals, guards, shields, or other
protective devices in place.
7. Never disconnect or bypass any switch.
8. Carbon monoxide in the exhaust fumes can be fatal when inhaled, never operate a machine without
properventilation.
9. Fuel is highly flammable, handle with care.
10. Keep engine clean.Allow the engine to cool before storing and always remove the ignition key.
11. Afterenginehas started,machinemust notmove.If movementisevident, theneutralmechanism isnot
adjusted correctly. Shut engine off and readjust so the machine does not move when in neutral position.
13. Never use your hands to search for oil leaks. Hydraulic fluid under pressure can penetrate the skin and
cause serious injury.
14. This machine demands your attention.To prevent loss of control or tipping of the vehicle:
A. Use extra caution in backing up the vehicle. Ensure area is clear.
B. Do not stop or start suddenly on any slope.
C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.
D. Stay alert for holes in the terrain and other hidden hazards.
15. Before leaving operator’s position for any reason:
A. Disengage all drives.
B.Lowerall attachmentsto theground.
C. Set park brake.
D. Shut engine off and remove the ignition key.
16. Keep hands, feet and clothing away from moving parts. Wait for all movement to stop before you clean,
adjust or service the machine.
17. Keep the area of operation clear of all bystanders.
18. Never carry passengers.
19. Stop engine before making repairs/adjustments or checking/adding oil to the crankcase.
20. Use parts and materials supplied by SMITHCO only. Do not modify any function or part.
These machines are intended for professional maintenance on golf courses and baseball fields. Other use is
forbidden.

3
Introduction
SPECIFICATIONS
WEIGHTSANDDIMENSIONS
Lengthwith Rake 85" (216 cm)
WidthwithRake 73.5" (187 cm)
Height 44" (112 cm)
Wheel Base 47" (119 cm)
Weight 990 lbs (449 kg)
SOUND LEVEL AT 3200 RPM
At earlevel 96 dB
At 3 ft (0.914 m) 90 dB
At 30 ft (9.14 m) 78 dB
ENGINE
Make Kubota
Model# ZB600E
Horsepower 12.5 Hp (9.5 kW)
Fuel No. 2 Diesel
CoolingSystem Liquid Cooled
LubricationSystem Full Pressure
Alternator 12.5amp
WHEELS&TIRE (3) 21 x 11.00 x 8 NHS 5 psi (0.35 bar)
Front tire fluid filled to 60lbs. total; 34.5 pints of windshield washer fluid or
equivalent.
SPEED
ForwardSpeed 0 to 10 mph (0-16 kph)
ReverseSpeed 0 to 4 mph (0-6 kph)
BATTERY (Not Included) Automotivetype 45-12volt
BCI Group Size 45
ColdCrankingAmps 480
GroundTerminal Polarity Negative(-)
MaximumLength 9" (23 cm)
MaximumWidth 5.38" (14 cm)
MaximumHeight 9" (23 cm)
FLUID CAPACITY
CrankcaseOil See EngineManual
Fuel 15.6 quart (14.8 liters)
HydraulicFluid 12.9 quart(12.2 liters)
Coolant .82gallon(3.1 liters)
Gradeof HydraulicFluid SAE 10W-40APIServiceSJ orhigher

4
Introduction
OPTIONALEQUIPMENT
13-680 Hydraulic Plow (Dealer Installed) 13-678 Castor Wheel Kit
13-644 ManualPlow,Aluminum Blade 13-298 FanRakeAttachment
13-679 Hydraulic Plow (Factory Installed) 34-191 BoxGrader
13-505 Attachment Lift (13-551 Only) 42-582 Spikerwith42-586MainFrame
13-107* InfieldScarifier,Chisel Blades 26-007 ProfessionalInfield Finisher
13-577* InfieldScarifier,Vertical Blades 26-008 FlexAction Field Finisher
13-116* SandCultivator 13-111 Drag Mat Kit
13-199* Edger Kit 42-550 Green Star Total RBS System
13-438 RakeAssembly 42-503 RBSMount for SmithcoSuper Rake
13-606 RakeAssembly with Lexan Blades 42-530 22-11.00 x 8Turf Track R/S Tire
42-026 84"StainlessSteelTournamentRake 42-531 22-11.00x8 CustomSmoothTreadTire
42-128 72"StainlessSteelTournamentRake 13-684 BrushKit for13-438 and13-606
* Must have 13-505 LiftAssembly installed before installation(13-551 Only)

5
Service
MAINTENANCE
Before servicing or making adjustments to machine, stop engine and remove key from ignition.
Use all procedures and parts prescribed by the manufacturer's. Read the engine manual
before operation.
Thesuggestedmaintenance checklistis notoffered as areplacement forthe manufacturer’s butas asupple-
ment.Youmust adhereto guidelinesestablishedby manufacturerfor warrantycoverage. Inadverse conditions
suchasdirt, mudor extremetemperatures, maintenanceshouldbe morefrequent.
LUBRICATION
UseNo. 2Generalpurpose LithiumBase Greaseand lubricateevery100hours.The DieselSuper Rakehas two
grease fittings. One is located in bearing on steering shaft and the other is on the relay on the foot pedal.
AIRCLEANERONFENDER
1. Removeend cap andfilter element, cleanby tapping gentlyon flat surface.Do not oilcartridge. Replace if
verydirty ordamaged.
2. Removeair cleanercapand clean.Cap canbe washed insolvent, makesure itsdrybefore reinstalling.
TIREPRESSURE
Caution must be used when inflating a low tire to recommended pressure. Over inflating can cause tires to ex-
plode.Tires shouldbe 5psi (0.35bar). Improperinflation willreducetire lifeconsiderably.
COOLANT
UsethePermanent (PT)antifreeze forthis engine.IMPORTANT: Whenthe antifreezeismixed withwater,the
antifreeze mixing ratio must be less than 50%.
TOWING
When it is necessary to move the Super Rake without engine running, bypass valve built into hydrostatic pump
must be "open" by turning it counterclockwise. The valve is located on bottom left of pump.An "open" valve al-
lowsfluid topass throughthe wheelsfreely. Whennormal,driven, operationis desired,valve shouldbe "closed
byturningit clockwise. Failureto "close" thevalve with enginerunning means nopower to wheels.The machine
can be moved for a short distance with the engine off, but we do not recommend this as a standard procedure.
When towing do not tow the machine faster than 2-3 MPH (3-5 km/h) because the drive system may be dam-
aged. The tires may lock up if the machine is towed too fast. If this occurs, stop towing the machine. If the ma-
chine must be moved a considerable distance, transport it on a truck or trailer.

6
Service
MAINTENANCE
ENGINEOIL
Changeandadd oilaccording to chartbelow. Donot overfill. Usea high qualitydetergent oilclassified"For Ser-
vice SJ or higher" SAE 30 oil. Use no special additives with recommended oils. Do not mix oil with gasoline.
SAEViscosityGrades
Starting Temperature Range Anticipated Before Next Oil Change
SAE 30 oil, if used below 40° F (4° C), will result in hard starting and possible engine bore damage due to inad-
equatelubrication.
HYDRAULICOIL
1. Use SAE 10W-40API Service SJ or higher motor oil.
2. Forproper warranty,changeoil every500 hoursor annually, whichever isfirst andchange filterafter the
first20 hours,thenat 100hours, thenevery 250hoursthereafter.
3. The oil level should be 2" to 21/2" from top of tank when fluid is cold. Do not overfill.
4. After changing oil and/or filter, run the machine for a few minutes. Check oil level and for leaks.
5. Always use caution when filling hydraulic oil tank or checking level to keep system free of contaminants.
Checkandservice morefrequently whenoperatingin extremelycold, hotor dusty conditions.
6. If natural color of fluid is now black or smells burnt, it is possible that an overheating problem exists.
7. If fluid becomes milky, water contamination may be a problem.
8. Ifeither oftheabove conditionshappen, changeoil andfilterimmediately afterfluid iscool and findcause.
Take fluid level readings when system is cold.
9. In extreme temperatures you can use straight weight oil. We recommend SAE 30WAPI Service SJ or
higherwhen hot(above 90°F(33°C)) andSAE 10WAPIServiceSJorhigherwhen cold(below 32°F(0°C)
ambient temperature. Use either motor oil or hydraulic oil, but do not mix.
10. Oil being added to the system must be the same as what is already in the tank. Mark tank fill area as to
which type you put in.
WHEELMOUNTINGPROCEDURE
1. Setpark brake.Turnmachineoffand removekey.
2. Block one of the other wheels.
3. Loosennuts slightlyonwheel tobe removed.
4. Jackup machinebeingcareful notto damageunderside ofmachine.
5. Removenuts, removeWheel.
5. Place new wheel on hub lining up bolt holes.
6. Torque nutsto 64-74ft/lb(87-100 Nm)usinga crosspattern.Retorqueafterfirst 10hoursand every200
hoursthereafter.
7. Lower machine to ground and remove blocks and jack.

7
Service
MAINTENANCE
BATTERY
Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or
any ignited object to come near the battery. When charging or working near battery, always shield your eyes
andalways provideproper ventilation.
Battery cable should be disconnected before using "Fast Charge".
Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging
rate. If electrolyte starts boiling over, decrease charging.
Always remove grounded (-) battery clamp first and replace it last.Avoid hazards by:
1. Filling batteriesinwell-ventilatedareas.
2. Wear eye protection and rubber gloves.
3. Avoid breathingfumes whenelectrolyte isadded.
4. Avoid spilling or dripping electrolyte.
Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte is
splashed on any part of your body, flush all contact areas immediately with liberal amounts of
water. Get medical attention immediately.
JUMP STARTING
Use of booster battery and jumper cables. Particular care should be used when connecting a
booster battery. Use proper polarity in order to prevent sparks.
To jumpstart(negative groundedbattery):
1. Shield eyes.
2. Connect ends of one cable to positive (+)
terminals of each battery, first (A) then (B).
3. Connect one end of other cable to negative (-)
terminal of "good" battery (C).
4. Connect other end of cable (D) to engine block
onunitbeing started(NOTto negative(-)terminal
of battery)
To prevent damage to other electrical components on unit being started, make certain that engine is at idle
speed before disconnecting jumper cables.

8
Service
SERVICECHART
Before servicing or making adjustments to the machine, stop engine, set park break, block
wheels and remove key from ignition.
Follow all procedures and ONLY use parts prescribed by the manufacturer. Read the engine
manual before maintenance.
C=Check or Clean at specified intervals
R=Replaceat specifiedintervals
* Tire pressure: 5 psi (0.35 bar)
† Replace hydraulic filters after the first 20, 100, and every 250 there after.
§ Torque tire nuts after the first 10 hours and every 200 hours there after (64 to 74 ft/lb (87-100 Nm))
¤ Change Oil and Filter after first 8 hours.
£ Change oil every 25 hours when operating under heavy load or in high ambient temperatures.
‡ Clean more often under dusty conditions or when airborne debris is present , replace air cleaner parts, if very dirty.
The suggested maintenance checklist is not offered as a replacement for the manufacturer’s engine manual but
as a supplement. You must adhere to the guidelines established by the manufacturer for warranty coverage. In
adverseconditions suchasdirt, mudor extremetemperatures, maintenanceshould bemore frequent.
Daily As Required 75 Hours 150 Hours 250 Hours 225 Hours 300 Hours Every 500 Hours/Yearly
¤ Engine Oil w/ Filter 3.28qt. (3.1 L) C R R R R R
¤ Engine Oil Filter R R R
Engine for Leaks and Loose Parts C C C C C C
‡AirCleaner(PaperElement) CCCC CCR
Idle Speed (1200 RPM) C C
‡CoolingSystem CCC CCC
Belts and Hoses C C C
* Tire Pressure C C C C C C
Visual Inspection of Tires C C C C C C
Fuel Level C C
FuelFilter RCC CCR
HydraulicOil C CC CCR
†Hydraulic Oil Filter R R
Hydraulic System for Leaks and Loose Parts C C C C C C
Battery Electrolyte Level C C C C C
Clean Battery Terminals C C
§ Torque Lug Nuts C C C
Lubricate C C C C C

9
Service
ENDUSER'SSERVICECHART
C=Check or Clean at specified intervals
R=Replace at specified intervals
* Tire pressure: 5 psi (0.35 bar)
† Replace hydraulic filters after the first 20, 100, and every 250 there after.
§ Torque tire nuts after the first 10 hours and every 200 hours there after (64 to 74 ft/lb (87-100 Nm))
¤ Change Oil and Filter after first 8 hours.
£ Change oil every 25 hours when operating under heavy load or in high ambient temperatures.
‡ Clean more often under dusty conditions or when airborne debris is present , replace air cleaner parts, if very dirty.
Daily As Required 75 Hours 150 Hours 250 Hours 225 Hours 300 Hours Every 500 Hours/Yearly
¤ Engine Oil w/ Filter 3.28qt. (3.1 L)
¤ Engine Oil Filter
Engine for Leaks and Loose Parts
‡ Air Cleaner (Paper Element)
Idle Speed (1200 RPM)
‡ Cooling System
Belts and Hoses
* Tire Pressure
Visual Inspection of Tires
Fuel Level
Fuel Filter
Hydraulic Oil
†Hydraulic Oil Filter
Hydraulic System for Leaks and Loose Parts
Battery Electrolyte Level
Clean Battery Terminals
§ Torque Lug Nuts
Lubricate

10
Service
ADJUSTMENTS
RAKELIFTCYLINDER
Completelylower RakeLift. Removecotterpin(A)
and clevis pin (B). Place attachment lift arms (C) at 1/
16"above crossmember(D) onRake Lift.Loosen jam
nut (E). Twist cylinder extension (F) so clevis pin end of
cylinder extension lines up with holes in attachment lift arm.
Replaceclevisand cotterpins. Tightenjam nut. Raiseand lower
RakeLiftto checkfor properclearance.
PARKBRAKE
By turning knob on end of lever you can tighten or loosen brake a small amount. Make all adjustments on knob.
Adjusting yokes will result in cable kinking.
STEERINGCHAIN
Steering sprockets (K) should be level with each other, check with straight edge.
Make any adjustments. Slide idler pulley (J) so that it is snug onto the chain.
Tighten all nuts and bolts in place.
LIFTASSEMBLY
When it is necessary to have attachment lift dig deeper or lower into
ground,relocatecylinder rodofhydraulic cylinderwhichcontrols thelift
distances, into lower set of holes in attachment lift swing arm. This
newposition forcesattachment fartherdown.
WHEEL‘CREEP’ADJUSTMENT
‘Creep’ is when engine is running and hydrostatic transmission is in neutral, but due to inadequate alignment
wheels still move. Do the following procedures to stop this motion.
1. Liftup and supportmachine so allwheels are off
theground andcanturn freely.
2. At rear of machine, on the Front of the hydro-
static transmission is the shift mount (A). Loosen
bolts (B).
3. Withenginerunning movestop (C)so itmoves
shift mount (A) to center and wheel creep stops.
4. Tighten all fasteners and test by using foot pedal
linkage to see that the "creep" is removed.
5. Turnengine offandlower machine.

11
Service
ADJUSTMENTS
SPEEDBOSS
Speed Boss allows the machine to operate at a proper speed
whilerakingbunkers ongolf courses.This speedhasbeen
factoryset atan averagespeedof3-4MPH(5-6.5kph).The
Speed Boss will only limit the speed while the rake is in
loweredintothe operatingposition. Thespeed settingmay
be adjusted by removing the ball joint (A) from the push pull
cable (B). Then loosen nut (C). Turn ball joint clockwise to
makethemachine operatefasteror turncounter clockwise
to go slower. Tighten jam nut. Connect ball joint to limiting
arm. Check to make sure nothing is binding and test drive to
checkdesiredspeed.
When the rear rake attachment is lowered while the machine is in forward position, the
forward speed of the machine will slow drastically. Operator should be prepared for rapid
change in speed.
STORAGE
Enginesstoredover 30days needto beprotectedor drainedof fuelto preventgumfrom formingin afuelsystem
oronessential carburetorparts.
1. Forengine protection,werecommend useof Briggsand StrattonGasolineAdditive,Part Number5041,or
acomparablegasolineadditive. MixAdditivewithfuel infuel tankor storagecontainer. Runengine fora
short time to circulate additive through carburetor. Engine and fuel can be store up to 24 months. Your
ServiceDealer hassingle-usepouchesofGasolineAdditiveavailable.
2. Ifengine is stillwarm, drainoil from crankcase.Refill withfresh oil ofrecommended grade.
3. Remove spark plugs and pour about 1 oz. (3 ml) of engine oil into cylinders. Replace spark plugs and
crank slowly to distribute oil.
4. Cleandirt andchafffromcylinders,cylinder headfins, blowerhousing, rotatingscreen andmuffler area.
5. Store in a clean and dry area, but NOT near a stove, furnace or water heater which uses a pilot light or any
device that can create a spark.

12
Diagrams
WIRINGDIAGRAM
Color Code Chart
Bl Blue
Br Brown
Y Yellow
Grn Green
O Orange
R Red
B Black
P Purple
W White

13
Diagrams
WIRINGDIAGRAMPARTSLIST
REF# PART# DESCRIPTION QUANTITY
1 Battery, 480 Cold Cranking Amps min. (not included) 1
22-054 Black Cable (negative) 1
76-236 Red Cable(positive) 1
12-031 Battery Boot (included with Red Cable) 1
2 Starter (on engine) 1
3 14-272 Seat Switch 1
4 17-202 TemperatureGauge 1
5 Temperature Sender (part of 17-202) 1
6 Engine Oil Sensor(on engine) 1
7 50-359 OilIndicator Light 1
8 12-017 Hourmeter 1
9 17-068 Ignition Switch (comes with engine) 1
17-079 Key Set 1
10 17-172 Glow Lamp Indicator (comes with engine) 1
11 22-017 30 Amp Fuse 1
34-146 FuseHolder 1
12 17-089 Rectifier (on engine) 1
13 DynamoAlternator (on engine) 1
14 17-171 GlowPlug 2
17-198 MainWire Harness 1
22-017 Ground Cable(engine to frame) 1

14
Diagrams
HYDRAULICDIAGRAM
HYDRAULIC PRESSURESHYDRAULIC PRESSURES
HYDRAULIC PRESSURESHYDRAULIC PRESSURES
HYDRAULIC PRESSURES
PumpDisplacement .913 in.3/ rev
Pump Input Speed (up to) 3600rpm
Max.Operating Pressure 3500 psi, 4500 Peek psi
ChargePump Displacement .33 in.3/ rev
Max.Inlet Vacuum 5 in. Hg
Max.Case Pressure 25 psi
ReliefValve Pressure(set at) 3600psi
13-729Hydraulic Valve (2bank) 1500 psi
13-730Hydraulic Valve (3bank) 1500 psi

15
Diagrams
HYDRAULICDIAGRAMPARTSLIST
REF# PART# DESCRIPTION QUANTITY
1 13-032 WheelMotor 1
2 13-424 Hydraulic Hose (631/4 long) 1
8840-62 FlexGuard Loom 1
3 13-425 Hydraulic Hose(701/4long) 1
8840-69 FlexGuard Loom
4 13-409 On - Off Valve 1
18-174 Elbow1/2StraightThread 2
18-228 HollowHex Plug 2
5 13-698 Hydraulic Hose (39" long) 1
6 13-584 OilTank 1
13-586 FillerBreather 1
7 8917-26 Suction Hose 5/81
18-040 HoseClamp 2
8 13-616 Hydraulic Hose(29" long) 1
9 8917-36 Suction Hose 5/81
18-040 HoseClamp 2
10 13-110 HydrostaticPump 1
11 23-006 Oil Filter 1
23-031 ReplacementFilter Only
12 8917-32 Suction Hose 5/81
18-040 HoseClamp 2
13 13-698 Hydraulic Hose (39" long) 1
14 13-617 Hydraulic Hose (25" long) 1
15 13-615 WheelMotor 2
16 13-612 HydraulicTube 2
17 42-265 OilCooler 1
18 13-633 Hydraulic Hose (191/2"long) 2
19 18-164 Hydraulic Hose(16" long) 2
20 13-292 HydraulicCylinder 1
21 13-357 HydraulicCylinder 1
23 13-549 Hydraulic Hose (241/8" long) 2
24 42-045 Hydraulic Hose (41" long) 2
HLC-A-200 LoomCLamp 2" 1
25 13-729 2-BankHydraulic Valve 1
78-418 BentHandle 1 perbank
13-730 3-BankHydraulic Valve
26 13-686 Hydraulic Hose (64" long) 1
27 13-406 HydraulicCylinder 1
28 13-444 Hydraulic Hose (50" long) 1

16
Parts
MAINFRAMEDRAWING

17
Parts
MAINFRAMEPARTSLIST
REF# PART# DESCRIPTION QUANTITY
1 13-712 LeftFloor Board 1
13-717 LeftRubber Mat 1
2 13-713 FrontBumper 1
3 HB-38-16-250 Bolt 3/8- 16 x 21/22
HW-38 Washer3/82
HNTL-38-16 Lock Nut 3/8- 16 2
4 13-208 BumperBrace 2
5 HB-38-16-350 Bolt 3/8- 16 x 31/22
HW-38 Washer3/82
HNTL-38-16 Lock Nut 3/8- 16 2
6 13-692 Console 1
HSDPS-14-100 SS Pan Head Drill Screw 1/4x 1 4
7 20-057 SteeringWheel 1
20-129 CenterCap 1
8 13-703 Seat Bracket 1
9 14-269 AdjustableSeat 1
13-398 Adjuster Set with 9" Handle 1
HNFL-516-18 Flange Whiz-Lock Nut 5/16 - 18 4
10 HB-516-18-100 Bolt 5/16 - 18 x 1 3
HNFL-516-18 Whiz Lock Nut 5/16 - 18 3
11 13-693 RearHood 1
78-384 Latch 2
HRS-316-1125 Pop Rivet3/16 x 11/86
12 13-570 Bracket 1
13 13-569 GasSpring60# 1
26-034 Ball Stud 2
HWL-516 Lockwasher5/16 2
HN-516-18 Nut 5/16 - 18 2
14 HB-516-18-200 Bolt 5/16 - 18 x 2 2
HNTL-516-18 Lock Nut 5/16 x 18 2
15 13-016 SeatHinge 1
16 HB-516-18-100 Bolt 5/16 - 18 x 1 2
HN-516-18 Nut 5/16 - 18 2
HW-516 Washer5/16 4
HWL-516 Lockwasher5/16 2
17 13-711 RightFloor Board 1
13-716 RightRubber Mat 1
18 13-708 MainFrame 1
19 13-611 Tireand Wheel 2
13-611-01 Tire 22 x 11.00 x 8 Turf Tamer 2
13-610-02 Wheel 2
60-268 Lug Bolt 1/2- 20 x 15/16 10
20 13-118 U-Bolt 2
21 13-705 Axle 1
HWL-12 Lockwasher1/24
HN-12-20 Nut 1/2- 20 4
(Continuedonnextpage)

18
Parts
MAINFRAMEDRAWING