Smithco Star 1015 User manual

Spray Star 1015/1016
SharpShooter-Rate Sync w/ Envizo Pro II
with 15’ and 18’ Booms
Oct 2016
Operator’s
Product Support: Hwy SS & Poplar Ave; Cameron WI 54822
1-800-891-9435 [e-mail]

CONTENTS
Introduction................................................................ 1-11
Introduction ................................................................. 1
Symbols................................................................... 2-3
Safety.......................................................................... 4
Safety Decal Location................................................. 5
General Safe Practices............................................... 6
Safe Spraying Practices ............................................. 7
Specifications.............................................................. 8
Optional Spray Equipment .......................................... 8
Set Up ......................................................................... 9
Controls & Instruments.........................................10-11
Operation ................................................................. 12-26
Operating Instructions.......................................... 12-14
Envizio Pro II Do’s and Don’ts................................... 14
SharpShooter-RateSync Console Features ............. 15
Initial Set Up of Envizio Pro II................................ 16-19
SharpShooter-Rate Sync Control ........................ 20-21
Spray Operation ................................................... 22-23
Re-Calibration of Flow Meter..................................... 22
SprayIntroduction ..................................................... 24
Turf Management ...................................................... 24
Hose & Handgun Spraying ........................................ 25
Nozzle Trouble Shooting ...................................... 25-26
Reference ................................................................ 27-32
Collection Times ....................................................... 27
Blended Pulse Tip Selection Guide ........................... 28
Declaration of Conformity ......................................29-30
Quick Reference .................................................................32

1
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
INTRODUCTION
Read this manual and all other manuals pertaining to the Spray Star 1000 carefully as they contain safety, oper-
ating, assembly and maintenance instructions. Failure to do so could result in personal injury or equipment
damage.
Keepmanualsin a safeplaceafteroperator andmaintenancepersonnelhave readthem.Rightand left sidesare
fromtheoperator’s seat,facingforward.
All SmithcoSmithco
SmithcoSmithco
Smithco machineshaveaSerialNumber and Model Number. Both numbers areneededwhenordering
parts. The serial number plate on the Spray Star 1000 is located on the left side in front of the front tire.. Refer to
enginemanualfor placementofengine serial number.Referto engine manualforplacement ofengineserial
number.
For product and accessory information, help finding a dealer, or to register your procuct please contact us at
www.Smithco.com.
Informationneededwhenorderingreplacementparts:
1. ModelNumberofmachine
2. SerialNumberof machine
3. NameandPart Numberofpart
4. Quantityofparts
For easy access record your Serial and Model numbers here.
CALIFORNIA
Proposition 65 Warning
Engineexhaustand someof itsconstituents
are known to the State of California to
cause cancer, birth defects, and other
reproductive harm.
WARNING
lb/kg Empty lb/kg Full

2
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SYMBOLS
ParkBrake ParkBrake
Release HydraulicOil
Level
Choke-OpenChoke-ClosedHandThrottle
HourMeter Hour Meter Fuse
GlowPlugGlowPlug- OffGlow Plug - On
RPM Gasoline Diesel
Water
Temperature
Temperature
Light
EngineOil
Engine - Stop Engine - Start Engine -Run
No Electrical
Power
ElectricalPower
ReadOperator’s
Manual

3
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SYMBOLS
NoSmoking MovingParts Manual
Operation
Pinch Point Step HotSurface
HydraulicFluid
Penetration LiftArm Tractor
Engage Disengage PTO
GroundSpeed Fast Slow
HHigh LLow FForward
RReverse NNeutral Warning
Danger
Caution
Up/RaiseDown/LowerUp/DownArrow

4
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SAFETY
Readandunderstandthismanual and all safety signsbeforeoperatingand maintaining. Review the safety
instructionsandprecautionsannually.
TAKE NOTE! THIS SAFETYALERT SYMBOL FOUND THROUGHOUT THIS MANUALIS USED TO CALL
YOURATTENTION TO INSTRUCTIONS INVOLVING YOUR PERSONALSAFETYAND THE SAFETY OF
OTHERS. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH.
SAFETY SIGNAL WORDS
Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The
appropriatesignalwordforeach has been selectedusing
thefollowingguidelines:
DANGER: Red.Indicatesanimminently hazardous situa-
tion that, if not avoided, will result in death or serious injury.
This signal word is to be limited to the most extreme
situations typically for machine components which, for
functionalpurposes,cannot be guarded.
WARNING: Orange. Indicatesapotentiallyhazardous
situation that, if not avoided, could result in death or serious
injury, and includes hazards that are exposed when guards
are removed. It may also be used to alert against unsafe
practices.
CAUTION: Yellow. Indicates a potentially hazardous
situation that, if not avoided, may result in minor or moder-
ate injury. It may also be used to alert against unsafe
practices.
IMPORTANT: Blue.Indicatesprocedureswhichshouldbe
followedtoavoiddamageto themachine.
Safety Alert Symbol
This symbol with a warning statement means:
“Warning, be alert! Your safety is involved!”
Carefully read the message that follows.

5
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SAFETYDECALLOCATION
If Safety Decals** have been damaged, removed, become illegible or parts replaced
without decals, new decals must be applied. New decals are available from your autho-
rized distributor.
This is a list of decals located on the Spray Star 1000. Part number, description and location will help in reorder-
ing a decals.
A 10-367 Decal, Spray Star 1000 Right and LeftTank Sides
B 25-356 Decal,TirePressure 20psi All Wheels
C 25-352** Decal,BypassValve HangTagonpump
D 25-298** Decal,WarningHot TailpipeGuard
D 25-286** Decal,CrushPinch Hood - Back Edge, Both Sides
RHControlPanel
E 15-719** Decal,Speed Control LHControlPanel
27-093** Decal,OilLevel LHControlPanel
F 25-370** Decal,88dba LH Front Panel
15-463** Decal,SprayPump LHFrontPanel
G 15-672 Decal,DashPanel Dash Board
H 25-373 Decal, Smithco FrontNoseCone
I 27-077 Decal, Smithco SteeringWheel
J 10-414** Decal,ControlPanel RH ControlPanel
K 25-277** Decal,BatteryWarning SeatPanel
**SafetyDecalsRequired
A
A
B
B
BB
CD
D
E
FG
H
I
J
K

6
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SAFEPRACTICES
1. It is your responsibility to read this manual and all publications associated with this machine.
2. Neverallowanyone to operateorservice themachineor its optionalequipmentwithout propertrainingand
instructions.Neverallow minors tooperateany equipment.
3. Learntheproper use of themachine,the location and purposeofall the controls andgaugesbeforeyou
operatetheequipment.Working with unfamiliarequipmentcan lead to accidents.
4. Wear all the necessary protective clothing and personal safety devises to protect your head, eyes, ears,
hands and feet. Operate the machine only in daylight or in good artificial light.
5. Inspect the area where the equipment will be used. Pick up all debris you can find before operating.
Bewareofoverhead obstructionsandunderground obstacles.Stay alertforhidden hazards.
6. Neveroperateequipment that isnotinperfect working orderorwithoutdecals, guards, shields,orother
protectivedevicesin place.
7. Never disconnect or bypass any switch.
8. Carbonmonoxidein the exhaustfumescan befatalwhen inhaled, neveroperatea machinewithoutproper
ventilation.
9. Fuel is highly flammable, handle with care.
10. Keep engine clean.Allow the enginetocoolbefore storing and alwaysremovetheignition key.
11. Disengageall drivesandsetpark brakebeforestartingthe engine.
12. Never use your handstosearchfor oil leaks. Hydraulicfluidunderpressure can penetrate theskinand
cause serious injury.
13. This machine demandsyourattention.Topreventlossof control ortippingof the vehicle:
A. Use extra caution in backing up the vehicle. Ensure area is clear.
B. Do not stop or start suddenly on any slope.
C. Reduce speed on slopes and in sharp turns. Use caution when changing directions on slopes.
D. Stay alert for holes in the terrain and other hidden hazards.
14. Beforeleavingoperator’sposition:
A. Disengageall drives.
B. Set park brake.
C. Shut engineoffandremovethe ignitionkey.
D. If engine has to run to perform any maintenance keep hands, feet, clothing and all other parts of body
awayfrommovingparts.
15. Keep hands, feetandclothingaway from movingparts.Waitfor all movementtostopbefore you clean,
adjustorservicethe machine.
16. Keep the areaofoperationclear of allbystanders.
17. Nevercarrypassengers.
18. Stopenginebeforemaking repairs/adjustmentsor checking/adding oiltothecrankcase.
19. Use parts and materials supplied by only. Do not modify any function or part.
20. Use caution when booms are down as they extend out beyond the center line of the machine.
21. The tank is a confined space, take precaution.
These machines are intended for professional maintenance on golf courses, sports turf, and any other
area maintained turf and related trails, paths and lots. No guaranty as to the suitability for any task is
expressed or implied.

7
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SAFESPRAYINGPRACTICES
Personsengagedinthe handling, preparationorapplicationof chemicals mustfollowacceptedpractices to
insurethesafetyof themselves andothers,
1. WEAR protectiveclothingincluding: gloves, hat,respirator,eyeprotectionand skincoveringsuitable for
protectionfromchemicals being used.
2. BATHE thoroughlyafterany exposure tochemicals,givingparticular attentiontoeyes,nose, ears and
mouth.
3. CLEAN equipmentandmaterialsin accordance withemployer,municipal andstateregulations.Useonly
approvedareas anddrains.
4. DISPOSE ofchemicalsandrinse solutions byapprovedand legal means.
5. PROVIDE methodsandmaterialsfor operators towasheyes and hands immediatelyduringthe spraying
process.
6. PROVIDE methodsandmaterialsfor control, safedilutionand neutralization of chemicalspillsduring
preparation,spraying,transporting andcleanup.
7. Always check and follow the directions and safety warnings of the chemicals to be used.
8. Securethedischargelines before startingthepump.An unsecureddischargelinemay whip.
9. Periodically inspect the pump and the system components.
10. Check hoses for weak or worn condition before each use. Make certain that all connections are tight and
secure.
11. Do not operate unit with leaks, frayed, kinked hoses or tubing. Repair or replace immediately.
12. Use only pipe,hoseandfittings rated formaximumpressure or pressure atwhichpressure relief valveis
set at. When replacing pipe, hose or fittings, use new product.
13. Do not operate any fuel engines in an enclosed area. Be sure the area is well ventilated.
14. Do not usethesepumpsfor pumping waterorotherliquids for humanoranimalconsumption.
15. Do not pump flammable or explosive fluids such as gasoline,
fuel oil, kerosene, etc.
Do not use in explosive atmospheres. The pump should be used
only with liquids compatible with the pump component materials.
16. Be sure allexposedmoving parts areguardedandthat allcouplingdevicesare securely attachedbefore
applyingpower.
17. Before servicing, disconnect all power, make sure all pressure in the system is relieved, drain all liquids
from the system and flush.
18. Protect pump fromfreezingconditions by drainingliquidand pumping rustinhibitingantifreezesolution
through the system, coating the pump interior.
19. TRANSPORT - Machine must be stopped to raise or lower booms. Because of cam system, if booms
areraisedintransit they canfallforward or backwardwhencomingto a stoporwhile traveling onuneven
terrain.

8
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SPECIFICATIONS
WEIGHTSANDDIMENSIONS
Length 112" (285cm)
Width 70"(178cm)
Width With Boom Open 180"(457m)
Height 48"(122cm)
Wheel Base 53" (135 cm)
Weight Empty 1480lbs(675kg)
Weight Full 2248lbs(1025 kg)
SOUNDLEVEL(DBA)
Atearlevel 85dba
At 3 ft (0.914 m) 83dba
At 30 ft (9.14 m) 72dba
ENGINE
Make Briggs & Stratton
Model# 386447
Type /Spec# 0058G1
Horsepower 23HP(17kw)
Fuel Unleaded87Octane GasolineMinimum
CoolingSystem AirCooled
LubricationSystem FullPressure
Alternator 25Amp
WHEELS&TIRE Front: Two 20 x 10.00 x 10 NHS Multi-Rib; 20psi (1.4 bar)
Rear: Two 24 x 13.00 x 12 NHS Multi-Trac; 20 psi (1.4 bar)
PARKBRAKE HandOperatedLever, DiscsonRearAxleSpeed 0 to 3 mph (0-4.8 kph)
SPEED
Forward Speed 0-8 mph(0-12.8kph)
Reverse Speed 0-3 mph(0-4.8kph)
BATTERY Automotivetype24F-12 Volt
BCIGroup Size 24
ColdCrankingAmps 575minimum
GroundTerminalPolarity Negative(-)
MaximumLength 10.25"(26 cm)
Maximum Width 6.88" (17 cm)
MaximumHeight 10" (25 cm)
FLUIDCAPACITY
CrankcaseOil SeeEngine Manual
Fuel 6 gallon(22.7liters)
HydraulicFluid 5gallon (19 liters)
Grade of Hydraulic Fluid SAE 10W-40API Service SJ or higher Motor Oil
OPTIONALEQUIPMENT
10-417 ChemicalCleanloadSafeFill System 1002 203 Spray System
10-419 Fresh Water Tank 1008 440 Spray System
17-601 15'HeavyDuty Boom 1010 3-Way Manual System
15-835 Tank Rinsing System 1011 Sharp Shooter + 440 Spray System
17-585 18'HeavyDuty Boom 10-378 FoamMarker
10-370 Water Meter Kit (liters) 30-141 26 Gal. Wash System
10-365 Water Meter Kit (gallons)
10-422 Hose Reel Mount Kit
16-129 ManualRewindHose Reel,200-foot/61-metercapacity
16-906 ElectricRewindHose Reel,200-foot/61-metercapacity

9
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
SETUP
TheSpray Star1000arrives from Smithco setupandready forservice.Depending on freightconditionsthe
battery may have to be installed.
The spray system is normally shipped attached to the 1000 Prime Mover. If a spray system is to be fitted to a
Prime Mover by a dealer or end user, assemble and attach the com-
ponents in accordance with the parts drawings in the Spray Star
1000Parts/ServiceManual.
1. Checkthetire pressure. Thefrontare20 psi (1.4 bar)andrear
tires are 18 psi (1.3 bar).
2. Battery is located under the seat. This is a negative grounding
system.
Connecting battery cables to the
wrong post could result in per-
sonal injury and/or damage to the
electrical system. Make sure
battery and cables do not interfere or rub on any
moving part. Connect red positive (+) cable (A) to
battery first. When disconnecting remove black
negative (-) cable (B) first.
3. Check hydraulic fluid level in tank located on the left side of the seat. Remove cap and add SAE 10W-40
API Service SJ or higher motor oil if necessary. Fluid level should be about 2-21/2" (5-6.4 cm) from the top
ofthetankwhen cold.DONOTOVERFILL.
4. Fill fuel tank, located on the right side, with Unleaded 87 Octane gasoline (minimum).
Fuel is flammable, caution must be used when storing or handling it. Do not
fill fuel tank while engine is running or an enclosed area, fumes are explosive
and dangerous to inhale. DO NOT SMOKE while filling the fuel tank. DO NOT
OVERFILL.
5. Machineshouldbe greased beforestarting,refer to SprayStar1000 Parts/Service Manualforlocation.
6. Attach the Spray Boom and any other Optional Equipment to the Prime Mover, in accordance with
instructions in the Spray Star 1000 Parts/Service Manual. The nozzles must be the correct distance above
theturfasdescribedin Turf Spraying Guide.The spray boommustoperateproperlyand the outer sec-
tions must break away safely if an object is struck by them, they must then return to normal operation
position.
7. Be sure to double check boom heights, nozzle spacing and displacement before spraying.
8. Machine is shipped with windshield washer fluid in Spray System to prevent freezing. Flush system
completely with clear water. Fill tank with water and retighten the four bolts used to hold the tank in place.
9. Readoperatinginstructions beforestarting.
Never allow pump to run dry! The valve on the suction side of the pump
(between the pump and tank) must be fully open whenever the pump is
operated.

10
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
CONTROLS &INSTRUMENTS
A. HourMeter -Thehourmeter indicates hoursofmachineoperation. It operatesonlywhen the ignition
switch is on.
B. Speedometer -TheSpeedometer indicatesgroundspeed of thevehiclein miles perhourand kilometers
perhour.
C. Oil Light - The oil light should come on when the ignition is on without the engine running and go out when
the engine is running. The oil light will light when the oil pressure is low. If oil light should come on, shut
engineoffimmediately and findthecause.
D. Ignition Switch - The ignition switch has three positions: Off - Run - Start.
E. Buzzer -The buzzer sounds if the pump is running dry.
F. Lights - This rocker switch turns lights on by pushing on the top and off by pushing on the bottom.
G. Spray Pump - This rocker switch turns the spray pump on by pushing on the top and off by pushing on the
bottom.
H. Left Boom Switch - This rocker switch lifts and lowers the left boom.
I. Right Boom Switch - This rocker switch lifts and lowers the right boom.
J. Choke - The choke is used in starting the engine.
Pull choke out to close choke plate when starting a
cold engine. Push in when engine starts.Awarm
engine may not require "choking" to start.
K. HandThrottle - The hand throttle is usedtoregulate
enginespeed.
L. Park Brake - The park brake is only a parking brake.
Pull back to release, push forward to apply. Some
adjustment can be made by turning the knob clock-
wise to tighten and counter clockwise to loosen.

11
Introduction
PARTS MANUALS AVAILABLE ONLINEATsmithco.com
CONTROLS&INSTRUMENTS
M. Spray Boss Control - Engages and disengages speed boss.
Forward is engage and all the way back is disengage. When
the lever is engaged it sets a stop for the accelerator. The
accelerator pedal must be used to maintain this speed.To
adjust speed use the knob on the end of the lever, counter
clockwise increases speed and clockwise decreases speed.
Disengagethelever andyouwill havefullaccelerator pedal
range.
N. Master Boom Switch - is used to override the master switch on
the computer console of the spray systems.
O. ReversePedal- Thispedalcontrols ground speedinthe
reversedirection.
P. Accelerator Pedal - This pedal controls ground speed. Press pedal to increase speed. Varying the amount
ofmovementof thepedalwill varythegroundspeed.
MASTERBOOMSWITCH
The master boom switch (P), located on the left floorboard is used to override the master switch on the computer
console of the spray systems. By pushing down it will turn on/off the booms.

12
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
OPERATION
BeforeoperatingtheSprayStar1000, become familiar with allcontrolsandfunctions.Also complete all mainte-
nancerequirementsandreadall safety warnings.Knowingthe SprayStar1000 thoroughly,howitoperates, and
by doing the prescribed maintenance steps, you can expect trouble free operation for years to come.
SAFETY
Safetyneedstoalways be theconcernofan operator ofamoving vehicle or anymachinewith moving parts.
1. Keep all shields and guards in place.
2. Keeptheparking brake engagedanytime the operatorisaway from thevehicleor whenever serviceis
performed.
3. Alwayswearthe necessary protectiveclothingandequipment.
4. Turn engineoffwhenrefueling orperformingmaintenance notspecificallyrequiringenginepower.
DAILYCHECKLIST
1. Checktheengine oil level.Addas needed.DO NOT OVERFILL.Referto engineowner'smanualfor oil
gradeand procedure.
2. Tirepressureshould be 20psi(1.4bar) maximum.
3. Inspect the electrical system and battery cables for loose connections or frayed wiring. Replace any faulty
equipmentortightenif loose.
4. Check hardware for loose or missing nuts, bolts, screws, etc., and tighten or replace as needed.
5. Inspect hydraulic lines for damage or leaks. Never use hands to inspect for leaks.
6. Check the hydraulic fluid level. The hydraulic fluid tank is located on the left side of the machine. The fluid
level should be 2"-2½" (5 - 6.4 cm) from the top of the tank when cold. Use only SAE 10W-40API Service
SJ or higher Motor Oil.
7. Inspectthesteering,throttle and shift linkages forgoodhookupsand
cleartravel.
8. Checkcontrolsfor smooth, properworkingoperation. Lubricate as
needed.
9. Check park brake adjustments. Adjust as required.
10. Checkanti-vibrationmounts onengineframe.
STARTINGTHEENGINE
1. Make sure the fuel flow valve is ‘On’. It is located on the fuel tank.
2. The ignition switch is located on the dashboard. Insert the key (A) and
turn clockwise until the engine starts (C). Release the key and it will
return to the run position (B). Use the choke and hand throttle as nec-
essary.
3. Allowengineto idle andwarmup before selectingdirectionoftravel.
STOPPINGTHEENGINE If the engine has been running under high power, let it run at slow idle speed a
few minutes to cool the engine down, before turning the ignition switch to the
OFF position.
1. Disengagespraypump.
2. Movethethrottle lever to “slow”andturnignition key tothe“off”position.
3. Removetheignition key andengagethe park brake.
Never leave the vehicle unattended with the engine running. Always bring the
vehicle to a complete stop, engage park brake, turn key off and remove key.

13
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
OPERATION
Before using the Spray Star, the operator and spray technician must familiarize themselves with all of the information on
chemical spraying contained in the Turf Spray Guide.
All testing and calibrating of sprayers is to be done with water, not chemicals. This
insures the safety to all involved in performing the calibration operation. Only after all
calibration procedures are completed should chemical be added to the sprayer.
TOWING UNIT
When it is necessary to move the Spray Star 1000 without the engine running, the bypass valve built into hydrostatic
pump must be "open" by turning it counterclockwise. The valve is located on the bottom of the pump. An "open" valve
allows fluid to pass through the wheels freely. When normal driven operation is desired, valve should be "closed" by
turning it clockwise. Failure to "close" the valve with engine running means no power to wheels.
HILLSIDE OPERATION
Do NOT stop or start suddenly on any slope. Be especially cautious when changing direction. Do NOT operate on
slopes greater than 20°.
BATTERY
Batteries normally produce explosive gases which can cause personal injury. Do not allow flames, sparks or any ig-
nited object to come near the battery. When charging or working near battery, always shield your eyes and always pro-
vide proper ventilation.
Battery cable should be disconnected before using “Fast Charge”.
Charge battery at 15 amps for 10 minutes or 7 amps for 30 minutes. Do not exceed the recommended charging rate. If
electrolyte starts boiling over, decrease charging.
Always remove grounded (-) battery clamp first and replace it last. Avoid hazards by:
1. Filling batteries in well-ventilated areas.
2. Wear eye protection and rubber gloves.
3. Avoid breathing fumes when electrolyte is added.
4. Avoid spilling or dripping electrolyte.
Battery Electrolyte is an acidic solution and should be handled with care. If electrolyte is
splashed on any part of your body, flush all contact areas immediately with liberal
amounts of water. Get medical attention immediately.
JUMP STARTING
Use of booster battery and jumper cables. Particular care should be used when
connecting a booster battery. Use proper polarity in order to prevent sparks.
To jump start (negative grounded battery):
1. Shield eyes.
2. Connect ends of one cable to positive (+) terminals of each
battery, first (A) then (B).
3. Connect one end of other cable to negative (-) terminal of
"good" battery (C).
4. Connect other end of cable (D) to engine block on unit being
started (NOT to negative (-) terminal of battery)
To prevent damage to other electrical components on unit being
started, make certain that engine is at idle speed before discon-
necting jumper cables.

14
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
OPERATION (CONTINUED)
SPRAYERVALVESETTINGSANDSPRAYTANKAGITATION
The gate valve on the suction side of the pump, between the tank and the pump must be open before pump is
engaged. Close this valve only when necessary to clean the filter with spray material in the spray tank.
Thereisonemanual flow controlvalveon the dischargesideofthe spray system.Thisvalve controls theagita-
tor.Thisvalve maybeopenedas much asnecessaryto provide hydraulicagitationthroughthequadrajet agitator
inthetankbottom. This valvemaybepartially closed to preventorreduce foam buildup fromthespraymaterials
inside the tank. When the liquid level in the spray tank reaches a certain level (usually 1-25 gallons (3.8-95 Li-
ters) depending on terrain and other conditions) it may be necessary to close the valve in the agitator line in
ordertopreventloss of suctionprime.
If your Spray Star is fitted with a hose reel, there is a second ball valve on the discharge system to supply mate-
rial to the hose reel.
The Quadrajet agitation system operates with four venturi jets in the tank bottom. These jets have replaceable
orifice discs which discharge the following amounts of spay material.
Input to Input to Agitator Agitator Agitator Agitator
Nozzle Agitator Agitator Pressure Pressure Output Output
Diameter in gpm in L/min in psi in bar in gpm in L/min
1/8" 1.9 7.2 25 1.7 6.3 23.8
1/8" 2.7 10.2 50 3.4 10.0 37.9
1/8" 3.8 14.4 100 6.9 15.0 56.8
5/32" 2.8 10.6 25 1.7 7.6 28.8
5/32" 4.2 15.9 50 3.4 12.2 46.2
5/32" 5.5 20.8 100 6.9 17.5 66.2
3/16" 3.6 13.6 25 1.7 9.1 34.4
3/16" 5.6 21.2 50 33.4 14.3 54.1
3/16" 7.9 29.9 100 6.9 18.7 70.8
You can change orifice disc sizes to enhance spray system performance. Smaller discs reduce amount of agita-
tion (desirable in some foaming materials) and make more dischargeable liquid available for nozzles. Larger (or
none) discs increase amount of agitation and make less dischargeable liquid available for nozzles.
ENVIZIOPROIIDO'SANDDON'TS
DO’S ANDDON’TS
Do havetheserial number andfirmwarerevisionavailable when callingfortechnical assistance. Itisbest if
the user is in the machine and in front of the field computer when calling for support.
Do reviewthemanual in itsentiretybefore operatingthefieldcomputer.
Do turn machine on prior to starting Envizio Pro II. Voltage spikes can cause damage to computer.
Don't letwateron or nearEnvizioPro IIComputer.
Don’t turnthefieldcomputer offwithout properly closinganyopen jobs andpoweringdownthe computer. If
the field computer loses power during a job, information within the job files may be lost and the associated
filesmaybecomecorrupt.
Do powerdownEnvizio prior toshuttingoff machine.
Don’t use sharp objects or harsh chemicals on the field computer touch screen as they may damage the
display.ConsoleFeatures
Do removeEnvizioPro II duringcoldweather. Coldweatherwillcause the batterytodrain.
EnvizioProIIcomes with aQuickReference Guide and anInstallation& Operation Manual.Pleaseread
thesemanualsbefore operation. Manualscanbe downloaded offthe internetat www.ravenprecision.com
andoffthewww.smithco.com website underPartsandTechnical Information.

15
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
ENVIZIOPROII-SHARPSHOOTER-RATESYNC FEATURES
INITALSETUP
To Begin a Job & Create a Spray Zone
Turn Sharpshooter w/RateSync On
Press Auto/Manual button to Auto
PSI is preset. Use arrow buttons to increase/decrease
POWER
Home
Screen
SwitchPro
AccuBoom
Switches
Master
ON/OFF
Increase/Decrease
Flow
GPSGreen- Signal
Yellow -Low Signal
Red - No Signal
POWER
Auto/Manual
Button

16
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
INITIALSETUP
1. Turn Raven Envizio Pro Controller On 2. Check to Insure GPS Icon is Green
Hold Blue Switch until screen lights up. Touch theGreenArrowtoenter JobMenu
Wait until Home ScreenAppears (see right) where you can Start aNew Job
3. New Job Menu 4. Start a New Job Screen.
Insure ArrowonTractorisForward Touch the Yellow New Job Box
Touch Icon toCorrectif Needed (Thiswillbringup the Keyboard Screen)
Touch the Blue “Job” Box to Start a New Job
5. Name the Job
This can be as elaborate or as simple as you like.
Examples: SouthCourseFairwayNo.4
Or SF4
Touch the Green“Check”Circle
Touch the Blue “Pattern” Box
(This Will Bring Up Your Next Pass Options)
Select “Last Pass” A – B

17
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
INITIALSETUP
6. Touch the “AccuBoom” Blue Box 7. Touch to Check “Use Spray Zone Map”
8. Touch the Yellow New “Field Boundary Map” 9. This will bring up the Keyboard Screen
Again,NametheNewField Boundary Map;
it’s best to use the same name as the New
Jobfile.Touch the Green “Check” Circle
This will return you to the Job “AsApplied” Screen
10. Creating a Field Boundary
Drive to the area where you want to start your Spray Zone. Press the Green “Menu” Box in the Lower
Right Corner ToBring Up the Tools MenuAlong the Right Side
Press the Black “Boundary Tools” Box
TouchtheBlack“Record FieldBoundary”Box

18
Operation
PARTS MANUALS AVAILABLE ONLINEAT smithco.com
INITIALSETUP
11. Select One of the Options Below to Create the Field Boundary
12. This will Enable the On Screen MappingTools
Stop” &“Pause”
13. Screen with Field BoundaryTools on Screen
14. Drive the Outline of theArea.You will see theYellow Line that will be the boundary of the
Field Boundary located at your selection point. Press the Black “Pause” Box at any time
toManeuvertheSprayer tocreatea Square Corner
15. Press the Black “Stop” Box when at the End of the Area You Want to Map. The Envizio
Pro will Draw a Straight Line to Point where Recording Began to Close the Spray Zone