SnowEx VX-1500 User manual

November 1, 2018
Lit. No. 70451, Rev. 06
V-Maxx™ G2 Hopper Spreader
VX-1500
Owner's Manual
Original Instructions
CAUTION
Read this document before operating
or servicing the spreader.
This manual supersedes all editions with an earlier date.

Lit. No. 70451, Rev. 06 3 November 1, 2018
TABLE OF CONTENTS
PREFACE.................................................................... 4
Owner's Information Form .................................... 4
SAFETY ...................................................................... 5
Safety Definitions.................................................. 5
Warning/Caution Labels ....................................... 5
Serial Number Label ............................................. 6
Safety Precautions................................................ 7
Fuses .................................................................... 7
Personal Safety..................................................... 8
Fire and Explosion ................................................ 8
Cell Phones........................................................... 8
Ventilation ............................................................. 8
Battery Safety ....................................................... 8
Noise..................................................................... 8
Vibration................................................................ 8
Torque Chart ......................................................... 9
LOADING .................................................................. 10
Certification......................................................... 10
Material Weights ................................................. 10
Spreader Specifications...................................... 10
Load Volume ....................................................... 11
Determining Vehicle Payload.............................. 11
Determining Vehicle Payload – Worksheet......... 12
MOUNTING THE SPREADER ................................. 13
Install Hopper in Vehicle Bed.............................. 13
Install Tie-Down Ratchet Straps................... 13
INSTALLING & REMOVING THE SPINNER
ASSEMBLY............................................................ 14
Install Spinner Assembly To Hopper................... 14
Remove Spinner Assembly................................. 14
OPERATING THE SPREADER – CAB CONTROL.. 15
Powering the Control .......................................... 15
Starting and Stopping Spreader ......................... 15
Controlling Material Application .......................... 16
BLAST/Maximum Application ...................... 16
Cab Control Modes............................................. 16
Standby Mode .............................................. 16
Ready Mode ................................................. 16
ON Mode ...................................................... 16
Error Mode ................................................... 16
Cab Control Codes ............................................. 17
Setup Procedures ............................................... 19
Calibrate Empty Hopper Setting
(Cb and EH Codes)................................... 19
Adjust LED Brightness Level
(LS and SL Codes).................................... 19
Auto-Reverse (Ar) Feature.................................. 20
Adjusting the Auto-Reverse (Ar) Setting ...... 20
Auto-Reverse (Ar) Sequence ....................... 20
Vibrator Function................................................. 20
Controlling the Flow of Material .......................... 20
Inverted V and Discharge Baffle .................. 20
Baffle Extension ........................................... 20
Spreading Tips.................................................... 21
Accessory LED Work Light................................. 21
Dump Function.................................................... 21
REMOVING & STORING THE SPREADER ............22
Remove Hopper From Vehicle Bed .................... 22
Store the Spreader.............................................. 22
MAINTENANCE........................................................ 23
Lubrication .......................................................... 23
After First Use..................................................... 23
After Each Use.................................................... 23
At End of Each Season or
After Extended Storage ................................... 23
Cab Control......................................................... 23
Fuse Replacement .............................................. 23
Recycle ............................................................... 23
ELECTRICAL COMPONENTS................................. 24
Vehicle Harness Diagram ................................... 24
Electrical Control Box Schematic .......................25
TROUBLESHOOTING GUIDE ................................. 26

Lit. No. 70451, Rev. 06 4 November 1, 2018
PREFACE
This manual has been prepared to acquaint you with
the safety information, operation, and maintenance of
your new hopper spreader. Please read this manual
carefully and follow all recommendations. This will
help ensure profitable and trouble-free operation of
your hopper spreader. Keep this manual accessible. It
is a handy reference in case minor service is required.
When service is necessary, bring your hopper
spreader to your distributor. They know your spreader
best and are interested in your complete satisfaction.
NOTE: This spreader is designed to spread snow
and ice control materials only. Do not use it
for purposes other than those specified in this
manual.
Register your spreader online at www.snowexproducts.com
OWNER'S INFORMATION
Owner's Name: ______________________________________________________________________
Date Purchased: _____________________________________________________________________
Outlet Name: ______________________________________________ Phone:_________________
Outlet Address: ______________________________________________________________________
Vehicle Model: _______________________________________________ Year: _______________
Spreader Type (Model):________________________________ Serial #:______________________
Length:________________________ Weight: __________________ lb/kg: _________________

Lit. No. 70451, Rev. 06 5 November 1, 2018
• DO NOT EXCEED GVWR OF VEHICLE
• DO NOT OVERLOAD SPREADER
• LOAD SPREADER EVENLY D6546
• Shut off control and unplug spreader before servicing.
ROTATING AUGER CAN CAUSE
SERIOUS INJURY OR DEATH
• Keep arms, hands, and loose clothing away from auger.
D6335
• Read Owner’s Manual for Installation Instructions.
• Secure spreader to truck with ratchet straps.
• Anchor spreader securely to truck body with bolt kit provided to prevent
slipping or sliding.
• Routinely check straps and handware to make sure they are secure.
D6548
SAFETY DEFINITIONS
NOTE: Indicates a situation or action that can lead
to damage to your spreader and vehicle or other
property. Other useful information can also be
described.
SAFETY
WARNING/CAUTION LABELS
Become familiar with and inform users about the
warning and caution labels on the spreader.
NOTE: If labels are missing or cannot be read, see
your sales outlet.
CAUTION
Indicates a potentially hazardous situation
that, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
WARNING
Indicates a potentially hazardous situation
that, if not avoided, could result in death or
serious personal injury.

Lit. No. 70451, Rev. 06 6 November 1, 2018
SERIAL NUMBER LABEL
SAFETY
Code Definition
YY 2-Digit Year
MM 2-Digit Month
DD 2-Digit Day
LL 2-Digit Location Code
XXXX 4-Digit Sequential Number
ZZZZZ 5–7-Digit Assembly Part Number
• Shut off control and unplug spreader before servicing.
ROTATING AUGER CAN CAUSE
SERIOUS INJURY OR DEATH
• Keep arms, hands, and loose clothing away from auger.
D6335
D6544
ROTATING PARTS AND FLYING OBJECTS
CAN CAUSE INJURY OR DEATH
• Keep hands, arms, feet and loose clothing away
• Shut off power ans stop engine before servicing
• Read owners manual before operating.
• Keep bystanders at least 60 ft away.
NO STEP
• Slippery Surface When Wet.
• May Cause Severe Injury
D6545
Serial Number Label
(inside frame)
TrynEx International, LLC
531 Ajax Drive
Madison Heights, MI 48071
YYMMDDLLXXXXZZZZZ
VX-1500 1.5 CU YD AUGER POLY HOPPER

Lit. No. 70451, Rev. 06 7 November 1, 2018
SAFETY
SAFETY PRECAUTIONS
Improper installation and operation could cause
personal injury and/or equipment and property
damage. Read and understand labels and this
Owner's Manual before installing, operating, or
making adjustments.
WARNING
• Driver to keep bystanders minimum of
25 feet away from operating spreader.
• Before working with the spreader, secure all
loose-fitting clothing and unrestrained hair.
• Before operating the spreader, verify that all
safety guards are in place.
• Before servicing the spreader, wait for
conveyor, auger, and spinner to stop.
• Do not climb into or ride on spreader.
WARNING
Do not install the control for this product in
the deployment path of an air bag. Refer to
vehicle manufacturer's manual for air bag
deployment area(s).
CAUTION
If rear directional, CHMSL light, or brake
stoplights are obstructed by the spreader, the
lights shall be relocated, or auxiliary directional
or brake stoplights shall be installed.
WARNING
Overloading could result in an
accident or damage. Do not exceed
GVWR or GAWR ratings as found
on the driver-side vehicle door
cornerpost. See Loading section to determine
maximum volumes of spreading material.
CAUTION
During the hopper installation we recommend
the addition of an OSHA compliant Backup
Alarm. This alarm is required for OSHA
governed employers.
CAUTION
Disconnect electric and/or hydraulic power
and tag out if required before servicing or
performing maintenance.
NOTE: Lubricate grease fittings after each use.
Use a good quality multipurpose grease.
FUSES
The electrical system contains several
automotive-style fuses. If a problem should occur
and fuse replacement is necessary, the replacement
fuse must be of the same type and amperage rating
as the original. Installing a fuse with a higher rating
can damage the system and could start a fire. Fuse
Replacement is located in the Maintenance section;
fuse ratings and locations are shown in the Vehicle
Harness Diagram in the Electrical Components section
of this Owner's Manual.
CAUTION
DO NOT leave unused material in
hopper. Material can freeze or solidify,
causing unit to not work properly.
Empty and clean after each use.
CAUTION
• Do not operate a spreader in need of
maintenance.
• Before operating the spreader, reassemble
any parts or hardware removed for cleaning
or adjusting.
• Before operating the spreader, remove
materials such as cleaning rags, brushes,
and hand tools from the spreader.
• Before operating the spreader, read the
engine owner's manual, if so equipped.
• While operating the spreader, use auxiliary
warning lights, except when prohibited by law.
• Tighten all fasteners according to the
Torque Chart. Refer to Torque Chart for the
recommended torque values.
WARNING
Vehicles <10,000 lb GVWR: Obstructing
the visibility from the vehicle's rear camera
could result in serious injury or damage. An
auxiliary camera system shall be installed
if the vehicle's rear camera is removed or
blocked.

Lit. No. 70451, Rev. 06 8 November 1, 2018
SAFETY
PERSONAL SAFETY
• Remove ignition key and put the vehicle in PARK
or in gear to prevent others from starting the
vehicle during installation or service.
• Wear only snug-fitting clothing while working on
your vehicle or spreader.
• Do not wear jewelry or a necktie, and secure long
hair.
• Wear safety goggles to protect your eyes from
battery acid, gasoline, dirt, and dust.
• Avoid touching hot surfaces such as the engine,
radiator, hoses, and exhaust pipes.
• Always have a fire extinguisher rated BC handy,
for flammable liquids and electrical fires.
FIRE AND EXPLOSION
Be careful when using gasoline. Do not use gasoline
to clean parts. Store only in approved containers away
from sources of heat or flame.
CELL PHONES
A driver's first responsibility is the safe operation of
the vehicle. The most important thing you can do
to prevent a crash is to avoid distractions and pay
attention to the road. Wait until it is safe to operate
Mobile Communication Equipment such as cell phones,
text messaging devices, pagers, or two-way radios.
WARNING
Gasoline is highly flammable and gasoline
vapor is explosive. Never smoke while
working on vehicle. Keep all open flames
away from gasoline tank and lines. Wipe up
any spilled gasoline immediately.
VENTILATION
BATTERY SAFETY
NOISE
Airborne noise emission during use is below 70 dB(A)
for the spreader operator.
VIBRATION
Operating spreader vibration does not exceed 2.5 m/s2
to the hand-arm or 0.5 m/s2to the whole body.
CAUTION
Batteries normally produce explosive gases
which can cause personal injury. Therefore,
do not allow flames, sparks, or lit tobacco
to come near the battery. When charging or
working near a battery, always cover your
face and protect your eyes, and also provide
ventilation.
• Batteries contain sulfuric acid, which burns
skin, eyes, and clothing.
• Disconnect the battery before removing or
replacing any electrical components.
WARNING
Vehicle exhaust contains lethal fumes.
Breathing these fumes, even in low
concentrations, can cause death. Never
operate a vehicle in an enclosed area without
venting exhaust to the outside.

Lit. No. 70451, Rev. 06 9 November 1, 2018
SAFETY
TORQUE CHART
1/4-20 109 154
1/4-28 121 171
5/16-18 150 212
5/16-24 170 240
3/8-16 269 376
3/8-24 297 420
7/16-14 429 606
7/16-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
7/8-14 474 669
644 9091-8
1-12 704 995
1/2-13
1/2-20
11.9
13.7
24.6
27.3
43.6
26.9
53.3
93
148
49.4
69.8
77.9
106.4
120.0
8.4
9.7
17.4
19.2
30.8
35.0
49.4
55.2
75.3
85.0
M6 x 1.00
M12 x 1.75
M8 x 1.25
M14 x 2.00
M10 x 1.50
M27 x 3.00
M22 x 2.50
M30 x 3.50
M24 x 3.00
M20 x 2.5011.1
19.5
38.5
67
107
7.7
613
778
1139
1545
450
428
562
796
1117
M33 x 3.50
M36 x 4.00
2101
2701
1468
1952
325
M16 x 2.00 231 167
M18 x 2.50 318222
Recommended Fastener Torque Chart
Size Size
Torque (ft- lb)
Grade
5
Grade
8
Metric Fasteners Class 8.8 and 10.9
These torque values apply to fasteners
except those noted in the instructions.
Torque (ft- lb)
Grade
5
Grade
8
Size Size
Torque (ft- lb)
Class
8.8
Class
10.9
Torque (ft- lb)
Class
8.8
Class
10.9
Inch Fasteners Grade 5 and Grade 8
CAUTION
Read instructions before assembling.
Fasteners should be finger tight until
instructed to tighten according to the Torque
Chart. Use standard methods and practices
when attaching spreader, including proper
personal protective safety equipment.

Lit. No. 70451, Rev. 06 10 November 1, 2018
SPREADER SPECIFICATIONS
Hopper
Model
Overall
Length
(in)
Bed
Length
(in)
Empty
Weight
(lb)
Overall
Width
(in)
Bed
Height
(in)
Capacity
Struck
(yd³)
VX-1500 89.5 66 550 49 34 1.5
LOADING
This Owner's Manual covers vehicles that have been
recommended for carrying the hopper spreader. Please
see your local dealer for proper vehicle applications.
CERTIFICATION
WARNING
Overloading could result in an accident or
damage. Do not exceed GVWR or GAWR as
found on the driver-side cornerpost of vehicle.
WARNING
New untitled vehicle installation of a spreader
requires National Highway Traffic Safety
Administration altered vehicle certification
labeling. Installer to verify that struck load of
snow or ice control material does not exceed
GVWR or GAWR rating label and complies
with FMVSS.
CAUTION
Read and adhere to manufacturer's
ice-control material package
labeling, including Material Safety
Data Sheet requirements.
MATERIAL WEIGHTS
Density
Material (lb/ft3)(lb/yd
3)(kg/m 3)
Salt 80 2160 1282
Sand 100 2700 1602
Material densities are approximate and are based on dry,
loose material. It is the responsibility of the operator to
know the weight of the material to be spread and the vehicle
carrying capacity.

Lit. No. 70451, Rev. 06 11 November 1, 2018
DETERMINING VEHICLE PAYLOAD
1. Install the hopper spreader and optional equipment
according to the Installation Instructions.
2. Install or attach any other equipment that will be
on the vehicle while the hopper spreader will be in
use (step bumper, trailer hitch, snowplow, etc.). Fill
gas tanks.
3. Obtain the Gross Vehicle Weight Rating (GVWR),
Front Gross Axle Weight Rating (FGAWR), and
Rear Gross Axle Weight Rating (RGAWR) from
the certification label located inside the driver-side
door jamb or door.
4. With the occupants in the vehicle for normal
hopper spreader operation, weigh the vehicle to
obtain gross vehicle weight (GVW).
5. Subtract the GVW from the GVWR to determine
the available material payload.
6. Obtain the weight per cubic yard (lb/yd³) of the
desired material. Divide the weight into the
payload to determine the maximum volume of
material that can be carried.
7. Refer to the Load Volume table and diagrams to
determine the maximum fill level for the material.
8. Fill the hopper with material to the calculated level.
Reweigh the vehicle with occupants and verify that
the Loaded Gross Vehicle Weight, Front Gross
Axle Weight, and Rear Gross Axle Weight are less
than the vehicle's ratings.
9. Repeat Steps 6–8 for each type of material.
The worksheet for Determining Vehicle Payload (next
page) includes an example.
WARNING
Overloading could result in an accident or
damage. Do not exceed GVWR or GAWR
ratings as found on the driver-side door
cornerpost of the vehicle. See Loading
section to determine maximum volumes of
spreading material.
LOADING
Hopper
Model
Load Volume (yd³)
ABC
VX-1500 (1.5 yd³) 1.7 1.5 0.7
LOAD VOLUME
A: Rounded Load
B: Struck Load
C: Flange
A
B
C

Lit. No. 70451, Rev. 06 12 November 1, 2018
Determining Vehicle Payload – Worksheet
Material Type Example:
Dry Salt
AEquipment installed when
vehicle was weighed
VX-1500
Spreader
BFront Gross Axle Weight
Rating [FGAWR] (lb) 6000
CRear Gross Axle Weight
Rating [RGAWR] (lb) 7000
DGross Vehicle Weight
Rating [GVWR] (lb) 11,000
EGross Vehicle Weight [GVW],
empty (lb) – 7402
F Payload Available (lb) = 3598
G Material Density (lb/yd³) ÷ 2160
H Maximum Volume (yd³) = 1.7
I
Maximum Material Fill Level,
approx. Refer to Load Volume
table and diagrams.
A
J
Loaded Front Gross Axle
Weight (lb) Must be less than
weight in Row B.
K
Loaded Rear Gross Axle
Weight (lb) Must be less than
weight in Row C.
L
Loaded Gross Vehicle Weight
[GVW] (lb) Must be less than
weight in Row D.
LOADING

Lit. No. 70451, Rev. 06 13 November 1, 2018
INSTALL HOPPER IN VEHICLE BED
NOTE: Periodically throughout the snow and ice
control season, verify that mounting devices
are secure.
1. If the spinner assembly has been stored inside
the hopper or is attached to the hopper, remove it
and set aside. Remove any debris from inside the
hopper.
2. Remove the vehicle tailgate.
3. Lift the spreader by all four large round holes on
the top of the diagonal corner rails (two shown
below), using slings or chains. Move the spreader
into the vehicle bed.
MOUNTING THE SPREADER
4. Adjust the spreader position to align the holes in
the hopper frame with the frame mounting holes in
the vehicle bed. If mounting holes are not already
drilled, refer to the hopper spreader Installation
Instructions for drilling instructions.
NOTE: Pay special attention when drilling or
clamping dissimilar metals to aluminum bodies.
Galvanic corrosion can occur if not handled
properly. Contact vehicle manufacturer for
recommended attachment practices.
5. Install the spreader to the vehicle bed using four
1/2" cap screws down through the spreader frame
and secure with 1/2" washers and 1/2" locknuts.
NOTE: If the mounting holes are not directly over
the vehicle box supports, the vehicle bed must
be braced to the frame to prevent buckling or
deforming the vehicle bed.
6. Install the frame spacer between the end of the
hopper frame and the front of the vehicle bed
as shown. If you do not have a spacer, refer to
the hopper spreader Installation Instructions for
directions on building one. Failure to install this
spacer could result in damage to the spreader.
7. Connect the vehicle-side harness to the
hopper-side harness.
Install Tie-Down Ratchet Straps
Install ratchet straps from the large round holes on the
top of the diagonal corner rails of the spreader frame
diagonally outward to the vehicle frame.
CAUTION
Before lifting, verify that the hopper is empty
of material. The lifting device must be able to
support the spreader's weight as shown in
the spreader specifications table.
Round Holes
(two per side)
Stop Bars
Frame Mounting
Holes
WARNING
Spreader shall be bolted to vehicle frame.
Do not rely on the tie-down chains or straps
alone to hold spreader in vehicle.
Frame Spacer
Built to Fit

Lit. No. 70451, Rev. 06 14 November 1, 2018
INSTALLING & REMOVING THE SPINNER ASSEMBLY
INSTALL SPINNER ASSEMBLY TO
HOPPER
1. Remove the 1/4" x 20" locking pin and hairpin
cotter, and open the cover.
2. Move the spinner assembly upward into position
and engage the tabs onto the locating pins.
IMPORTANT: When installing the spinner
assembly on the spreader, make sure that the
material chute fits under the trough of the hopper.
3. Install the locking pin through the spinner
assembly and the locking pin tabs on the spreader
frame. Secure the latch to the cover.
4. Connect the spinner motor plug to the spinner
harness plug on the rear of the electrical control
box.
REMOVE SPINNER ASSEMBLY
1. Release the latch. Disconnect the wire harness.
2. Swing the hood open.
3. Remove the 1/2" x 20" locking pin.
4. Lift the spinner assembly off of the locating pins.
Latch
Tabs
Cover
Locating
Pin
Locking
Pin Tabs
Locking
Pin
Hairpin
Cotter
Material
Chute

Lit. No. 70451, Rev. 06 15 November 1, 2018
OPERATING THE SPREADER – CAB CONTROL
POWERING THE CONTROL
Power is not applied to the control until the vehicle
ignition is turned to ACC or ON. Once the control
has power it performs a light check and displays the
software version on the status display. The control
then checks for a connected spreader. If no spreader
is detected, the following occurs:
• nC (no connection) appears on the red status
display for five seconds;
• A single beep sounds;
• Control enters Standby mode with no lights
illuminated.
If any button is pressed on the control, it will wake and
check again for spreader connection. If no spreader
is detected, it will act as previously described. If a
spreader is detected, it will transition to Ready Mode.
STARTING AND STOPPING SPREADER
To start the spreader, press the ON/OFF button. The
control backlights are illuminated when the vehicle
ignition is ON and the spreader is connected. When
the spreader is ON, the ON/OFF button and inner arc
around each control knob will also illuminate.
To stop the spreader, press the ON/OFF button
again.
The ON/OFF button also operates as an emergency
stop when required.
NOTE: The vehicle ignition must be ON to start
the spreader.
NOTE: If vehicle ignition is turned OFF while
spreader is running, the motors will stop.
Material
Width
Material
Flow
VIBRATE LIGHT STROBE PREWET
MIN MAX
ON/OFF
MIN MAX
BLAST
Material Width
Control Knob
(Spinner Speed)
Indicator Lights
(8 per Knob)
Material Flow
Control Knob
(Feed Rate)
BLAST Button
(Maximum Application)
ON/OFF Button
& Emergency Stop
Status/Error Code
Display (Red)
Accessory
Control Buttons
WARNING
Before starting the spreader, the driver shall
verify that all bystanders are a minimum of
25 feet away from operating spreader.
WARNING
Never operate equipment when under the
influence of alcohol, drugs, or medications that
might alter your judgment and/or reaction time.
WARNING
Never exceed 45 mph (72 km/h) when loaded
spreader is attached to vehicle. Braking
distances may be increased and handling
characteristics may be impaired at speeds
above 45 mph (72 km/h).
WARNING
Never allow children to operate or climb on
equipment.

Lit. No. 70451, Rev. 06 16 November 1, 2018
OPERATING THE SPREADER – CAB CONTROL
CONTROLLING MATERIAL APPLICATION
The material application settings can be adjusted
while the spreader is ON or OFF. Settings are shown
by the indicator lights around the control knobs. When
the spreader is OFF, a single LED will light to show the
current setting. When the spreader is ON, the number
of blue LEDs illuminated will increase/decrease as the
knobs are turned clockwise/counterclockwise.
The hopper drive will not deliver material until the ON
button is pressed.
The Material Width (left) knob controls spinner speed.
Turning the knob clockwise will increase the width of
the application area.
The Material Flow (right) knob controls the hopper
drive. Turning the knob clockwise will increase the
feed rate of material to the spinner.
Turning the control knobs counterclockwise will
decrease the width of the application area and the
feed rate of material.
BLAST/Maximum Application
1. Press and hold the BLAST button when maximum
flow rate and application area are needed
temporarily. The BLAST button will illuminate
while depressed.
2. Release the button when maximum application
settings are no longer needed.
NOTE: Spinner speed and material feed rate revert
to the previous settings once the BLAST button
is released.
CAB CONTROL MODES
Standby Mode
Vehicle ignition is set to ACC or ON; cab control is
OFF. Control has power. No spreader was detected.
No lights are illuminated on the control. Press any
button to wake.
Ready Mode
Vehicle ignition is set to ACC or ON; cab control is OFF.
Control has power. Spreader is detected.
The Material Width and Material Flow control knobs
can be set to start-up conditions, but the spinner and
drives will not operate until the cab control is turned
ON.
Accessory lights and vibrator are operational. The
BLAST function is not operational.
ON Mode
Vehicle ignition is set to ACC or ON; cab control is ON.
Spinner and hopper motors will start. All cab control
functions are operational. Accessory lights and
vibrator are operational.
During normal spreader operation, no control codes
are displayed. Information or setup codes will appear
when relevant. These codes will not stop spreader
operation.
Error Mode
When an error condition occurs, spreader operation
will shut down. A two-character error code will flash
on the display and a beep will sound. If there are
multiple error codes, the codes will flash in a repeating
sequence.
Refer to the Error Codes portion of the
following Cab Control Codes table. Also see the
Troubleshooting Guide section of this manual.
Once the error condition has been resolved, press the
ON/OFF button to clear the error code(s). Press the
ON/OFF button again to resume spreader operation.
The error code will reappear if the error condition
has not been rectified. If the error condition persists,
contact your authorized dealer.
Multiple resets within a short time frame will cause
the hopper module to time out if components are
overheating. The control will display an EF error code.
Accessory work lights and strobe lights can be used
when an error code is in effect and will remain in
their current state. The vibrator and pre-wet will not
function.

Lit. No. 70451, Rev. 06 17 November 1, 2018
OPERATING THE SPREADER – CAB CONTROL
Error Codes – Spreader Operation Stopped
Code Definition Possible Cause Suggested Solution
bb Bad button. Button is stuck.
Button was pressed while
vehicle ignition was entering
ACC or START mode.
Inspect control. Free up button.
Do not press any spreader cab control buttons
while the vehicle ignition is being engaged.
bH Bad hopper. Possible module or control
mismatch.
Replace control or module. Use only genuine
service parts. Contact authorized dealer.
CE No communication with
spreader module.
Loose connection.
Module lost power.
Disconnected spreader
harness while vehicle is ON.
Confirm that spreader and control harnesses are
connected to the vehicle harness. Check power
to spreader module, all connections, fuses, and
power studs. Check that port B is plugged in.
CP Spinner assembly present
fault.
Spinner assembly harness is
not attached.
Install the spinner assembly harness. Reset the
control by pressing the ON/OFF button.
Ct Control is hot. Cab temperature is too high.
Control overheated.
Turn OFF spreader and allow control to cool off.
EF Excessive drive faults. Too many HO and/or SO
error codes; hopper module
overheating.
Control times out for 60 seconds.
Ensure that the auger and/or spinner are not
jammed.
Setup Codes
Code Definition Procedure
Cb Calibrate the Empty Hopper setting. With control in ON mode, press and hold the left control knob until the
Cb code displays. Calibration cycle is automatic.*
Cc Clear calibration data for Empty Hopper
setting; clear EH code.
Press the right control knob to clear all calibration data during the
calibration cycle.
LS Set LED brightness level. With control in Ready mode, press and hold left control knob to get
LS code. Release pressure and turn left control knob to desired
brightness setting. Wait for confirming SL code to display.*
SL Confirms that LED brightness level has
been reset.
* For full instructions, see "Setup Procedures" in the Operating the Spreader – Cab Control section of this manual.
Information Codes
Code Definition Response
Ar Auto-reverse sequence is active. The spreader will automatically detect and attempt to clear a jam. See
the Operating the Spreader section of this manual.
dU Spreader is in dump mode:
• Spinner assembly is removed.
• Back Dump buttons are enabled.
To operate the dump function, see instructions in the Operating the
Spreader section of this manual.
If dU code displays when the spinner assembly harness is attached,
contact authorized dealer.
EH Empty hopper (beep will sound). Check hopper for material.
Recalibrate Empty Hopper setting as described above for Cb code.
Lb Low battery. Hopper module is sensing
<10V. (Lb becomes an error code
when module senses <6V.)
Refer to the Lb row under "Error Codes" (next table).
CAB CONTROL CODES
Table continues on next page.

Lit. No. 70451, Rev. 06 18 November 1, 2018
OPERATING THE SPREADER – CAB CONTROL
Error Codes – Spreader Operation Stopped
Code Definition Possible Cause Suggested Solution
HO Hopper overload –
software trip.
Drive system has high current.
Material is jammed.
Auger is damaged.
Inspect auger; clear material jam, or fix auger as
needed.
HO .Hopper overload –
hardware trip.
HP Hopper power issue.
No motor present.
Hopper drive motor is not
connected.
Possible motor defect.
Check connections to the auger drive motor
(P–FEED and FEED–N posts on the module and
studs on the motor).
Replace the motor.
Lb Low battery. Hopper
module is sensing ≤6V.
Bad connection or low battery.
Snowplow or other vehicle
power use may be driving
down voltage.
Voltage is measured at the hopper module;
therefore, Lb code may indicate cable voltage
loss. Check battery, alternator, and connections.
nC No connection. Spreader not connected to
vehicle harness.
Connect vehicle and spreader harness.
Check vehicle harness fuse.
Inspect spreader and vehicle harnesses.
Check module.
OH Overheating. Spreader module is too hot.
Spreader module malfunction.
Accessories wiring/function
problem.
Drive motor overload.
Allow a cool-off period of 60 seconds or longer.
Check for loose harness connections.
Check accessory connections. Check integrity of
accessory wiring and harness.
Clear jammed material.
Contact authorized dealer.
OH .Overheating module –
microprocessor.
rS Reset of spreader module. Power loss to module detected
on startup.
Reset the control by pressing the ON/OFF button.
Check vehicle harness and battery connection.
SO Spinner drive overload –
software trip.
Material jammed in spinner.
Spinner shaft is damaged.
Inspect spinner and spinner drive components for
alignment and condition.
SO .Spinner drive overload –
hardware trip.
SP Spinner power issue.
No motor present.
Spinner drive motor is not
connected.
Possible motor defect.
Check connections to the motor (SPIN and GND
posts on the module).
Replace the motor.
CAB CONTROL CODES continued

Lit. No. 70451, Rev. 06 19 November 1, 2018
OPERATING THE SPREADER – CAB CONTROL
SETUP PROCEDURES
Calibrate Empty Hopper Setting
(Cb and EH Codes)
Calibrating the empty hopper setting enables the cab
control to alert the operator when the hopper is empty.
Recalibrate the empty hopper setting at the start of
each ice-control season.
1. Verify the hopper is empty before beginning the
calibration.
2. Turn the vehicle ignition to ACC or ON. Press
the ON/OFF button on the cab control to turn the
control ON.
3. Press and hold the Material Width (left) knob
for approximately 10 seconds until the Cb code
displays.
4. The calibration cycle will begin. The blue LEDs
around the Material Flow (right) knob will illuminate
in succession until all eight are lit.
5. When the automatic calibration cycle is complete,
the control will automatically revert to the previous
material application settings.
If the control is turned OFF or loses power during
the calibration cycle, the calibration data will be lost.
Make sure the control is ON and restart the calibration
process at Step 3.
After the empty hopper setting has been calibrated,
the EH code will flash on the display and a beep will
sound whenever the hopper is empty. The EH code is
informational only and will not stop spreader operation.
Clearing Empty Hopper Calibration Data (Cc Code)
The empty hopper calibration may be cleared, if
desired. The control will no longer display the EH
status code when the hopper is empty.
Start the calibration cycle as described above. At
Step 4, press the Material Flow (right) knob during the
calibration cycle to clear all calibration data. The Cc
(Clear Calibration) code will display and the control will
exit Cc mode automatically.
Adjust LED Brightness Level
(LS and SL Codes)
The brightness setting of the cab control lights can be
adjusted from 1 to 16. The factory default setting is 8.
1. Turn the vehicle ignition to ACC or ON. If
necessary, press the cab control ON/OFF button
to turn the control OFF.
2. Press and hold the Material Width (left) knob for
approximately 3 seconds until the LS code is
displayed.
3. Release the knob and turn it clockwise or
counterclockwise to increase/decrease the
brightness level. The light level number will show
in the status display.
4. After selecting the desired brightness level, wait
a few seconds for the SL confirmation code to
display.
NOTE: A brightness level setting of 12 or higher is
recommended for daylight conditions.

Lit. No. 70451, Rev. 06 20 November 1, 2018
OPERATING THE SPREADER
VIBRATOR FUNCTION
A heavy-duty vibrator is standard equipment on the
model VX-1500 spreader. Turn the vibrator ON as
needed to keep dense material flowing and prevent
bridging of material in the hopper.
A second vibrator can be added. Accessory vibrator
kits are available through your authorized dealer.
CONTROLLING THE FLOW OF MATERIAL
Inverted V and Discharge Baffle
The V-Maxx™ 1500 hopper spreader uses an
inverted V baffle design over the auger area. This
baffle is used to reduce the load to the auger drive
train. It must not be removed unless servicing the unit.
This spreader also uses a discharge baffle to reduce
material leakage. Do not remove the discharge baffle
unless servicing the unit.
Baffle Extension
The baffle extension is intended to be used with very
dry products that free-flow with little effort. The baffle
is designed to keep these types of materials from
leaking out.
• If using damp/wet materials, remove this baffle by
removing the self-drilling screws.
• If using a sand/salt mixture, remove the baffle
extension.
AUTO-REVERSE (Ar) FEATURE
The spreader is automatically able to sense and clear
material jams. The sensitivity level of the auto-reverse
feature is adjustable.
Adjusting the Auto-Reverse (Ar) Setting
1. With the spreader connected and the control
powered up in the READY mode, press and hold
the BLAST button. After 5 seconds, a number will
appear on the status display (factory default is 20).
2. Continue to hold the BLAST button and turn
the right-hand knob to control the material flow
setting (range is 2–30). Turn the knob clockwise to
increase the flow. Turn the knob counterclockwise
to decrease the flow.
3. Release the BLAST button.
4. Press the ON/OFF button twice (turning the
spreader ON, then OFF) to save the setting.
5. If auto-reverse is too sensitive or not sensitive
enough, repeat Steps 1–4 and adjust the value. If
the value is set to 30, the auto-reverse feature will
be disabled.
Auto-Reverse (Ar) Sequence
The Ar sequence will begin automatically, and consist
of a series of reverse-then-forward movements of the
auger.
The Ar sequence will make up to five attempts to
clear the jam. The status display will flash Ar then a
number, and repeat as it counts down from 5 to 1. If
the jam is cleared, the auger will automatically return
to normal operation at the previous control settings.
If auto-reverse is unsuccessful, then the operator must
extract the material that is causing the problem. Follow
all warning directions when clearing jams.
CAUTION
Disconnect electric power and tag out, if
required, before servicing or performing
maintenance.
Baffle
Extension
Self-Drilling
Screws
Discharge
Baffle
Inverted V