Socket 9M User manual

Socket Bluetooth®Cordless Ring Scanner
Series 9
User’s Guide

2/2009 Document # 6410-00273 P
COPYRIGHT NOTICE
Copyright © 2005-2009 Socket Mobile, Inc. All rights reserved.
Socket, the Socket logo, Battery Friendly, Socket Bluetooth Cordless Ring
Scanner, SocketScan, Connect!Agent, Error Proof Protocol, ActivePairing,
SocketCare, Business Mobility Now! and Mobility Friendly are registered
trademarks or trademarks of Socket Mobile, Inc. Bluetooth and the Bluetooth
logos are trademarks owned by Bluetooth SIG, Inc., U.S.A. and licensed to
Socket Mobile, Inc. All other brand and product names are trademarks of
their respective holders.
The Bluetooth Cordless Ring Scanner includes technology licensed under
United States Patent No. 5,902,991, 7,429,000 B1, D510,087S, D554,641 S,
and D570,350, and European Community Registered Designs 000522289-
0001 and 000522289-0002.
Reproduction of the contents of this manual without the permission of Socket
is expressly prohibited. Please be aware that the products described in this
manual may change without notice.
Feel free to contact Socket at:
Socket Mobile, Inc.
39700 Eureka Drive
Newark, CA 94560-4808
USA
Other than the above, Socket can assume no responsibility for anything
resulting from the application of information contained in this manual.
Please refrain from any applications of the Socket Bluetooth Cordless Ring
Scanner that are not described in this manual. Please refrain from
disassembling the Bluetooth Cordless Ring Scanner. Disassembly of this
device will void the product warranty.
You can track new product releases, software updates and technical
bulletins online at: socketmobile.com

IMPORTANT!
The information in this User’s Guide is based on version 3
of the Bluetooth Cordless Ring Scanner hardware, which
includes devices with any of the following part numbers:
Bluetooth
CRS version Ring Unit Part
Number Wrist Unit Part Number
9M 8550-00032 8550-00028
9P 8550-00027 8550-00028
The features described in this manual that do not apply to older
hardware versions of the Bluetooth Cordless Ring Scanner will be noted
as such.

4
TABLE OF CONTENTS
COPYRIGHT NOTICE 2
1 | INTRODUCTION 6
About the Software 6
Performance Levels 6
System Compatibility Requirements 7
Package Contents 8
Product Registration 8
SocketCare™ Service Program 8
Advanced Programming Guide 8
Product Diagram 9
Cable Break Away 9
Status Indicator LEDs and Beeps 10
2 | HARDWARE PREPARATION 11
Assembling the AC Adapter 11
Charging and Installing the Battery 11
Assembling and Putting on the Bluetooth CRS 13
3 | SETUP FOR WINDOWS MOBILE 16
STEP 1: Uninstall Other Scanning Software 17
STEP 2: Install SocketScan and Connect!Agent 18
STEP 3: Start SocketScan 21
STEP 4: Enable Cordless Scanner Support 21
STEP 5: Turn on the Bluetooth CRS 22
STEP 6: Connect Device to Bluetooth CRS 23
STEP 7: Assemble and Put on the Bluetooth CRS 25
STEP 8: Open your Application 25
STEP 9: Scan Data into Your Application 26
Disconnecting 27
Symbology Selector 28
Scanner Settings 29
Scan Demo 31
Connect!Agent Utility 32
Dual Device Support 33
4 | SETUP FOR WINDOWS XP AND VISTA 34
STEP 1: Uninstall Other Scanning Software 35
STEP 2: Install the Software 35
STEP 3: Turn on the Bluetooth CRS 37
STEP 4: Start Bluetooth On Your Computer 37
STEP 5: Configure Bluetooth Settings 38
STEP 6: Start SocketScan 44
STEP 7: Configure Scanner Settings 44

TABLE OF CONTENTS 5
STEP 8: Connect Computer to Bluetooth CRS 47
STEP 9: Assemble and Put on the Bluetooth CRS 48
STEP 10: Open Your Application 48
STEP 11: Scan Data into Your Application 49
Scanner Settings 51
Advanced Scanner Settings 52
Remote Trigger Button 55
Floating Trigger 56
Symbology Selector 57
5 | ACTIVEPAIRING 58
APPENDICES
A SPECIFICATIONS 65
B SCANNING, SAFETY AND USAGE TIPS 68
C BAR CODE LABEL SPECIFICATIONS 72
D ENABLING OR DISABLING SYMBOLOGIES 74
E DECODE ZONE 76
F RESTORING FACTORY DEFAULTS 78
G TROUBLESHOOTING 79
H TECHNICAL SUPPORT 83
LIMITED WARRANTY 84
REGULATORY COMPLIANCE 87

6
1 | INTRODUCTION
Thank you for purchasing the Socket Bluetooth Cordless Ring
Scanner (CRS) Series 9 with Bluetooth wireless technology. This
wearable device provides hands-free bar code scanning to boost
productivity in warehousing, inventory control, shipment tracking,
and other data capture applications.
The Bluetooth CRS features a durable design that is IP54 compliant,
with an exclusive Liquidmetal®construction that is twice as strong as
titanium, extremely rugged and scratch-resistant.
The Battery Friendly® design uses minimal power, so you can use the
Bluetooth CRS for up to 10 hours on a single charge.
The Bluetooth CRS features a Class 1 Bluetooth radio so you can
scan bar codes while wirelessly connected to computer located up to
300 feet (100 m) away. Socket offers multiple wireless connection
tools, including Connect!Agent™ software and ActivePairing™, which
automate the connection process.
ABOUT THE SOFTWARE
SocketScan™software feeds scanned data into any open program,
as if the data were manually typed. A configuration utility that
enables you to select Prefix/Suffixes, sounds, and other special
settings for the Bluetooth CRS.
Connect!Agent™software for Windows Mobile simplifies Bluetooth by
automatically setting up and managing the wireless connection.
PERFORMANCE LEVELS
Performance
Level Features Ring Unit Part Number

CHAPTER 1: INTRODUCTION 7
9M
Mid-range Class 1 laser for normal indoor use 8550-00032 8550-00025
8550-00022
9P
Performance Class 2 laser for demanding requirements like scanning outdoors in sunlight, over long distances or
through Mylar, auto windshields, or other glass
8550-00027
8550-00024
8550-00018
SYSTEM COMPATIBILITY REQUIREMENTS
Windows Mobile:
•Any of the following Windows Mobile versions:
−Windows Mobile 2003, 2003SE or 5.0 for Pocket PC/Pocket PC Phone
−Windows Mobile 6.0 or 6.1 Classic/Professional
•Bluetooth radio and any of the following Bluetooth stacks:
−Broadcom 1.5 or greater
−Microsoft Bluetooth stack for Windows Mobile
−Stonestreet One 1.2.4 (Build 1783) for Windows Mobile
Note: Software installation requires a host PC, connection cable/ cradle, and
ActiveSync or Windows Mobile Device Center software, available free from the
Microsoft website. Alternatively, advanced users can install a CAB file (please
see Readme file for instructions).
Windows XP and Vista:
•Windows XP Professional/Tablet PC (SP1, SP2, SP3) or
Windows Vista Business/Ultimate (SP1)
•Bluetooth radio and any of the following Bluetooth stacks:
−Broadcom 5.1.0.1700 or greater
−Microsoft Bluetooth stack
−Toshiba 4.00.34, 5.00.06F or greater
Note: For information and instructions on using the Bluetooth CRS with the
Intermec CK30, please contact Socket technical support.

8
PACKAGE CONTENTS
Wrist unit Ring unit Coiled cable
Finger straps (2) Wrist strap Wrist unit case
Li-ion battery Battery charger AC adapter with plugs
for USA and Europe
CD with software and
documentation
PRODUCT REGISTRATION
Socket recommends that all customers register their products.
Registered users benefit from priority technical support and can choose
to get special offers, and product/upgrade information. Register online
at: www.socketmobile.com/support/support/new
SOCKETCARE™SERVICE PROGRAM
The SocketCare service program is available for the Bluetooth CRS. For
more information, please visit: www.socketmobile.com/support/
ADVANCED PROGRAMMING GUIDE
The SocketScan Advanced Programming Guide is available online at:
www.socketmobile.com/support/downloads/

CHAPTER 1: INTRODUCTION 9
PRODUCT DIAGRAM
Note: The Bluetooth Device Address is labeled on the bottom of the wrist unit.
It helps you identify your CRS.
CABLE BREAK AWAY
The Bluetooth CRS is designed to break away from the hand if
subjected to unusual force. This feature is designed to reduce the risk
or extent of injury in case the Bluetooth CRS gets entangled with
industrial equipment. If the cable breaks away during use, simply plug
it back in to resume operation.
Power button
Good Read LED
Left Tri
gg
er Button Ri
g
ht Tri
gg
er Button
Bluetooth Status LED
Batter
y
Status LED
Batter
y
Door Lock
Coiled cable
Wrist Unit
Rin
g
Unit

10
STATUS INDICATOR LEDS AND BEEPS
Ring Unit LED
LED LED Activity Meaning
Good Read
(Green LED) On Data successfully scanned and sent
to host device
Wrist Unit LEDs
LED LED Activity Meaning
Solid on Side power button pressed
1 blink per
second Bluetooth radio is on, no connection
Bluetooth
Status
(Blue LED) 1 blink every 3
seconds Bluetooth connection
Blinking 20% battery capacity remaining
On 10% battery capacity remaining
Battery Status
(Red LED) Off Off or Good Battery status
Wrist Unit Beeps
Beep Pattern Meaning
2 beeps (low-high) Power on
2 beeps (high-low) Power off
1 beep CRS connected to host computer
2 beeps
(same tone) CRS disconnected from host computer
1 beep with green
LED (optional
setting)
Data successfully scanned and sent to host
computer
3 long beeps Cable disconnected from wrist unit
5 beeps CRS has detected an error and reset

CHAPTER 2: HARDWARE PREPARATION 11
2|HARDWARE PREPARATION
ASSEMBLING THE AC ADAPTER
The AC adapter for the Bluetooth CRS
charger comes with plugs for USA and
Europe.
1. Insert the appropriate plug for your region
into the AC adapter.
2. While pressing the release button, push
down on the plug and turn it clockwise until
it locks into place.
3. Release the button.
CHARGING AND INSTALLING THE BATTERY
Notes:
•Please charge the battery before initial use.
•You can charge the battery before or after inserting it into the wrist unit.
•The charger can charge a wrist unit and spare battery simultaneously.
•Do not use the charger or Bluetooth CRS with other batteries, doing so
will void the warranty.
•A fully charged battery can power 12,000+ scans in ~ 10 hours under
normal conditions.
Battery Charger LEDs
LED LED Activity Meaning
Power Red Plugged into valid power source
Yellow Charging
Charging Green Battery is fully charged

12
OPTION 1:
Charge battery
separately.
When inserting the battery, make sure the metal contacts of the battery
touch those inside the charger.
OPTION 2:
Charge battery
inside wrist
unit.
After installing the battery (see instructions below), connect the charger
cable to the top of the wrist unit.
Installing the
Battery
Use a coin or screwdriver to unlock the battery door. Open the door.
With the wrist unit right-side up, insert the battery with the blank side of
on top and metal contacts in front.
Metal contacts
WARNING! To prevent damage to the battery, do not insert it
backwards or upside-down!
Close and lock the battery door. The door will not fully close if the battery
is inserted wrong.

CHAPTER 2: HARDWARE PREPARATION 13
ASSEMBLING AND PUTTING ON THE BLUETOOTH CRS
STEP 1:
Attach finger
strap to ring
unit.
Insert clip post into slot and gently push down. Repeat on other side.
Important! Do not twist the clips during insertion or removal!
Note: To remove, grasp a clip and gently pull out. Repeated removal
may distort the post and make it unusable.
STEP 2: Put on
wrist strap.
The wrist strap can be worn on the right or left wrist. Adjust for a
comfortable fit.
Note: A shorter, 6-inch strap is also available, SKU#.
STEP 3:
Connect cable
to ring unit.
Plug the narrow end of the cable into the connector on the back
of the ring unit.

14
STEP 4: Put on
the ring unit.
Insert index finger, adjust strap for a comfortable fit, and secure
into place.
STEP 5: Insert
wrist unit into
case.
Insert the wrist unit into the case and fasten into place.
Note: You may hear a beep and see the LED flicker because the power
button was pressed during insertion. However, the wrist unit will not turn
on unless the button was pressed for more than 2 seconds (you will
hear 2 beeps).

CHAPTER 2: HARDWARE PREPARATION 15
STEP 6: Attach
the wrist unit
and connect
the cable.
Press the wrist case onto the wrist strap and connect the cable
into the top of the wrist unit.
Replacement Parts
Straps and other replaceable components of the Bluetooth CRS are
available in single or multi-packs.
Part SKU#
Coiled cable, 1 pack AC4044-1139
Coiled cable, 10 pack AC4045-1140
Battery, 5 pack AC4031-714
Finger Strap, 10 pack AC4027-710
Wrist Unit Case, 10 pack AC4029-712
Wrist Strap, 10 pack AC4028-711

16
3|SETUP FOR WINDOWS MOBILE
This chapter explains how to install and use the Bluetooth Cordless
Ring Scanner (CRS) with a Bluetooth enabled Pocket PC or other
Windows Mobile powered device.
Before you begin the instructions in this chapter, make sure you
have charged and installed the battery as explained in Chapter 2,
“Hardware Preparation.”
SETUP SUMMARY
STEP 1: Uninstall other scanning software.
STEP 2: Install SocketScan and Connect!Agent.
STEP 3: Start SocketScan.
STEP 4: Enable cordless scanner support.
STEP 5: Turn on the Bluetooth CRS.
STEP 6: Connect device to Bluetooth CRS.
STEP 7: Assemble and put on the Bluetooth CRS.
STEP 8: Open your application.
STEP 9: Scan data into your application.
Application Features
Symbology selector
Scanner settings
Scan Demo
Connect!Agent utility

CHAPTER 3: SETUP FOR WINDOWS MOBILE 17
STEP 1: UNINSTALL OTHER SCANNING SOFTWARE
Remove any bar code scanning software already installed in your
device, including previous versions of SocketScan.
OPTION 1: Uninstall Directly from the Pocket PC
1. Make sure the bar code scanning software is not running, and
remove or disconnect any Socket data collection products from
your Pocket PC.
2. Tap Start | Settings. Tap on the System tab or Control Panel.
3. Tap on the Remove Programs icon.
4. Use the utility to remove the software.
OPTION 2: Uninstall via ActiveSync
1. Make sure the bar code scanning software is not running, and
remove or disconnect any Socket data collection products from
your device.
2. Use ActiveSync and a serial/USB cable or cradle to make an
active connection between your device and a host PC.
3. On the host PC, open Microsoft ActiveSync.
4. Click Tools | Add/Remove Programs.
5. Use the utility to remove the software.

18
STEP 2: INSTALL SOCKETSCAN AND CONNECT!AGENT
ADVANCED USERS: Refer to the README file for CAB installation instructions.
1. Make an active connection between your device and a host PC.
Use a USB/serial connection cable or cradle and synchronization
software (ActiveSync or Windows Mobile Device Center).
Note: The synchronization software is available free from the Microsoft
website.
2. Insert the installation CD into your host PC.
3. If it does not start automatically start, use My Computer or
Windows Explorer to access your CD-ROM drive. In the CD,
click on SETUP.EXE.
4. The SocketScan Setup Center will appear in your web browser.
Read the first page and click Installation in the left margin.

CHAPTER 3: SETUP FOR WINDOWS MOBILE 19
5. In the Windows CE section of the SocketScan Installation page,
click Install In the first paragraph.
6. Your web browser will present a series of dialogs.
Internet Explorer:
•In the File Download –Security Warning dialog, click Run.
•In the second warning dialog, click Run.
•Internet Explorer will download the file.
Firefox:
•In the file opening dialog, click Save File.
•Firefox will download the file.
•In the Downloads list, next to SocketScanCE.exe, click Open.
•In the warning dialog, click OK to continue.
7. The installation wizard will automatically begin. Follow the wizard
to install the software.

20
8. When software installation is complete, remove the device from
the cradle. Soft reset the device by either tapping ok when
prompted or pressing the reset button.
9. Install Connect!Agent. Return to the SocketScan Setup Center
Installation page. Scroll down to the Connect!Agent – Mobile
Devices section and click on the Connect!Agent software link
there.
IMPORTANT! You must install both SocketScan and
Connect!Agent software!