Socket DURASCAN D750 User manual

Bluetooth Barcode Scanner
Model D750
www.socketmobile.com
DURASCANTM
SERIES 700
socketmobile.com

Package Contents 4
Product Information 5
Scanner Setup 6
Charge the Battery 7
Optional Charging Accessories 8
Powering Scanner On/Off 9
Scanning Barcodes 10
Bluetooth Connection Modes 11
Setup without software application (Basic Mode):
• Android 13
• Apple 14
• Windows (Peripherals) 15
TABLE OF CONTENTS

Setup using Application Mode:
• Android or Windows Mobile Device 16
• Windows PC 18
• Apple® iOS 20
Unpairing Bluetooth Connection 22
Bluetooth Reconnection 23
Scanner Status Indicators 24
Product Specifications 28
Helpful Resources 30
Safety, Compliance &Warranty 31-41
Battery Warning 36-37
Changing the Scanner Settings 41
TABLE OF CONTENTS

© 2010-2016 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, and
SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The
Bluetooth word mark and logo are registered trademarks of the Bluetooth SIG, Inc.
USA, and any use by Socket Mobile, Inc. is under license. All other trademarks and
trade names contained herein may be those of their respective owners.
USB A to USB
Type-C Cable
Lanyard
DuraScan
D750
Thank you for choosing Socket Mobile!
Let’s get started!
PACKAGE CONTENTS

PRODUCT INFORMATION
5
The D750 has a protection rating of IP54 for dust and water protection. It is also
made with antimicrobial additives for protection against harmful microbes.
*Also used to display the on-screen keyboard in Basic Mode (iOS only).
Scanner head
Product label
Lanyard Eyelet
Scan Indicator Light
Trigger button
Power button*
Battery Light (Green/Yellow/Red)
Bluetooth Light (Blue)
Pins for
charging
cradle
Power Connector Stand Attachment

Attach the Lanyard (optional)
1. Detach the string loop of the tether from the lanyard.
2. Feed the string loop through the eyelet.
3. Pull tight so the string loop is secure.
4. Reattach the string loop to the tether from the lanyard.
SCANNER SETUP
6

The scanner must be fully charged before rst use. Please allow 6 hours
uninterrupted charging for the initial battery charge.
Lift the rubber ap to access the power connector.
• Yellow/Amber Light = Charging
• Green Light = Fully charged
Important: Charging from a computer USB port is not reliable and
not recommended.
CHARGE THE BATTERY
Rubber Flap
To open
“Beep Beep”
7

Available separately.
OPTIONAL CHARGING ACCESSORIES
8
Charging Cradle Charging Stand AC Power Supply
International Adapters
available
For all optional accessories visit our Socket Store.

Powering On:
Press and hold down the small
power button until the Battery
light turns on and the scanner
beeps twice (low-high).
Powering Off/ Disconnecting:
Press and hold down the small
power button until the scanner
beeps twice (high-low) and lights
turn off.
The scanner will power off au-
tomatically if device is not con-
nected within 5 minutes. Scanner
connected to a device will power
off within 2 hours if idle/inactive.
POWERING ON/OFF
Power button
9

1D Barcode
Aim the scan beam straight
across the entire barcode.
2D Barcode
Aim at the center.
Scanning Barcodes
1. Hold the scanner a few inches from the barcode.
2. Aim, press and hold the trigger button.
By default, the scanner will beep, vibrate, and the scan indicator will
ash green to conrm a successful scan.
Caution: Do not stare directly into the scanner light beam.
SCANNING BARCODES
Trigger button
10

Connect your scanner using one of the following Bluetooth connection
modes:
Bluetooth Connection Proles
Bluetooth Mode Description
Basic Mode (HID)
(Default)*
Human Interface
Device Prole
• NO software installation required
• Connects to most devices
• Good for barcodes containing small amounts of
data
• Scanner interacts with host device like a keyboard
Application Mode
(SPP)
Serial Port Prole
For Android or Windows
• Software installation is required
• More efcient and reliable data communications
for barcodes containing lots of data
• If you have an application that supports Socket
Mobile Scanners this is the mode recommended
Application Mode
(MFi-SPP)
Apple Specic
Serial Prole
For iOS Devices
• Must use with an App developed to work with
iOS devices
• Software installation is required
• If you have an iOS application that supports
Socket Mobile Scanners this is the mode you
want to use
*By default, the scanner is set to Basic Mode (HID).
BLUETOOTH CONNECTION MODES
11

Operating System Connection Options
Operating
Systems
(OS)
Devices
Bluetooth
HID
Support
Bluetooth
SPP
Support
Bluetooth
Apple
Serial
Specic
(MFi Mode)
Android Android 4.0.3 &
later Yes Yes N/A
Apple iOS iPod, iPhone, &
iPad Yes N/A Yes
Windows
Mobile
Windows Mobile
6.x (SoMo only) Yes Yes N/A
Windows PC Windows 7, 8, 10 Yes Yes N/A
Mac OS
Mac OS X 10.4 to
10.X
Mac Books, Mac
Mini, &iMac
Yes No N/A
Note: To switch from one mode to the other you must remove the
pairing information from both devices - host computer and the scanner.
(see unpairing procedure on page 21)
12
BLUETOOTH CONNECTION MODES

Android: Connect Android Device in Basic Mode
In this mode the scanner functions and communicates similar to a key-
board. Therefore, scanner will work with Notes, and any other
application that support an active cursor.
1. Power on the scanner. Make sure the scanner is
discoverable (unpaired) The Blue light blinks fast.
2. Settings | Bluetooth.
3. Make sure the device has Bluetooth “On” and scan for devices.
4. In the list of found devices, select D750 [xxxxxx]. Tap Pair.
5. The scanner will connect to the Android device.
6. The scanner will beep once after it has connected.
*If you have trouble connecting or pairing with host device, turn host
device’s Bluetooh off/on, and/or perform factory reset to the scanner
(see page 44).
Now you are ready to scan barcodes!
BASIC MODE
13

Apple: Connect to Apple iOS Device or Mac OS Device Basic Mode
In this mode the scanner functions and communicates similar to a key-
board. Therefore, scanner will work with Safari, Notes, and any other
application that support an active cursor.
1. Power on the scanner. Make sure the scanner is
discoverable (unpaired). The Blue light blinks fast.
2. Start a Bluetooth device search.
• Settings | Bluetooth: Turn on Bluetooth and search for device.
• Mac OS: Click System Preferences | Bluetooth. A Bluetooth device
search will begin.
3. In the device list, tap on D750 [xxxxxx]. Tap Pair.
4. The scanner will connect to the Apple device.
5. The scanner will beep once after it has connected.
Now you are ready to scan barcodes!
To use the virtual keyboard while the scanner is connected, double tap on
the power button. See YouTube video for demonstration.
14
BASIC MODE

APPLICATION MODE
Connect Android or Windows Mobile Device:
In this mode the scanner functions and communicates similar to a key-
board. Therefore, scanner will work with Notes, and any other
application that support an active cursor.
1. Power on the scanner and scan this barcode. The scanner will beep
3 times. Make sure the scanner is discoverable (unpaired). The blue
light will blink fast.
(Scanning this barcode changes the connection mode)
2. Turn Bluetooth on for your device. Go to Settings > Bluetooth. A
Bluetooth Devices search will begin.
3. Tap Socket D750[xxxxxx] in the list of Devices found. After a few
seconds the “Not Paired” status will change to “Connected” or
“Paired” and the scanner blue light will stop blinking and turn solid
blue.
Now you are ready to scan barcodes!
15

APPLICATION MODE
Connect Android device in Application Mode using EZ Pair
Install Software
1. Go to GooglePlay Store, search for “SocketScan ”.
2. Download &install. Follow the on screen instructions.
Getting Started
3. Follow the on screen instructions.
4. Tap on screen the ON SCREEN button.
5. Tap on screen the 2D SCANNER button.
6. Scan the barcode on the device screen. Wait a few seconds. The
scanner will beep 3 times indicating it has accepted the command to
connect to your device.
7. When notied of a pairing request, swipe the notication icon down,
then tap Pairing request.
8. On the next screen, tap Pair.
9. The scanner will beep once to indicate connected state and is ready to
scan barcodes. Tap Back to close Socket EZ Pair.
10.If you are connecting a scanner which is not registered, a scanner
registration icon will appear on top of the screen. Swipe the icon down
to open the registration screen. Follow the instructions to register
your Scanner. Socket Mobile highly recommends that all customers
register their products for future updates, but registration is optional.
Now you are ready to scan barcodes!
16

APPLICATION MODE
Connect Windows PC in Application Mode
Note: Make sure you have administrative privileges.
1. Download the latest SocketScan 10 software from Socket Mobile’s
support web page.
2. Follow the on-screen instructions to install the software.
3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM
port.
Note: If there is none please click Ports to create at least one new
incoming COM port in Bluetooth settings.
4. Click Finish.
Now you are ready to scan barcodes!
17

APPLICATION MODE
To pair the scanner with Windows PC using EZ Pair:
1. Power on the scanner. Make sure the scanner is available to be
connected to Bluetooth (unpaired).
2. Launch SocketScan 10 and click on the SocketScan 10 icon in the task
tray. In the pop-up menu, click Socket EZ Pair.
3. Click 2D scanner accordingly.
4. Scan the barcode that appears on the screen.
5. The PC will automatically try to pair with the scanner. If prompted
to allow the pairing, click Yes. If prompted for a passkey, enter 0000
(four zeroes).
6. After the scanner connects, it will beep once. Close Socket EZ Pair.
6a. In Windows 10 if this step can not be done, open the Bluetooth
settings and add and pair the scanner manually.
7. If you are connecting a scanner which is not registered, a scanner
registration icon will appear on top of the screen. Follow the
instructions to register your scanner. Socket Mobile highly recommends
that all customers register their products, but registration is optional.
8. The task tray icon will change to indicate the status of the
connection.
Now you are ready to scan barcodes.
18

APPLICATION MODE
Connect Apple iOS device in Application Mode
Please check with your scanner application vendor or visit
www.socketmobile.com/appstore to conrm your scanner-enabled
application supports the scanner.
If you are using the scanner with an Apple iOS device and a
scanner-enabled Application that does not provide instructions how to
connect your scanner, please use the following steps.
1. Power on the scanner. Make sure the scanner is discoverable
(unpaired). The Blue light should be blinking fast.
2. To change the prole to Application Mode scan this barcode. The
scanner will beep 3 times.
Use with iPad, iPod touch, and iPhones.
(Scanning this barcode changes the connection mode)
3. Turn on Bluetooth on the Apple device. Go to Settings > Bluetooth.
A Bluetooth Devices search will begin
(Continue on page 20)
19

APPLICATION MODE
4. Tap Socket D750[xxxxxx] in the list of other devices found. After a
few seconds the “Not Paired” status will change to “Connected” or
“Paired” and the scanner blue LED will stop blinking and turn solid
blue.
Note: The characters in brackets are the last 6 characters of the
Bluetooth Address.
5. Launch your scanner-enabled Application. The scanner will beep once
indicating that it is connected to the appropriate application.
Now you are ready to scan barcodes!
20