Socket DURASCAN D750 User manual

Bluetooth Barcode Scanner
Model D750
www.socketmobile.com
DURASCANTM
SERIES 700
socketmobile.com

Application Mode (MFi-SPP) Setup for Apple® iOS 22
Application Mode (SPP)
• Android 17
• Windows PC 20
• Windows (Peripherals) 20
Basic Mode (HID)
• Android 13
• Windows PC 14
• Windows (Peripherals) 15
Battery Charger &Battery Warning 40-44
Bluetooth Connection 25
Bluetooth Connection Modes 11
Bluetooth Unpairing 24
Command Barcodes 26
Helpful Resources 34
TABLE OF CONTENTS

Optional Charging Accessories 8
Package Contents 4
Powering on/off 9
Product Information 5
Product Specifications 33
Safety, Compliance &Warranty 35-46
Scanning Barcodes 10
Status Indicators 30
TABLE OF CONTENTS

© 2010-2016 Socket Mobile, Inc. All rights reserved. Socket, the Socket logo, and
SocketScan are registered trademarks or trademarks of Socket Mobile, Inc. The
Bluetooth word mark and logo are registered trademarks of the Bluetooth SIG, Inc.
USA, and any use by Socket Mobile, Inc. is under license. All other trademarks and
trade names contained herein may be those of their respective owners.
AC adapter* &USB to
DC plug cable
*Use the plug that is
regionally appropriate
Lanyard
DuraScan
D750
Thank you for choosing Socket Mobile!
Let’s get started!
PACKAGE CONTENTS

PRODUCT INFORMATION
5
*Also used for keyboard Pop-up in Basic Mode (HID) only
Scanner head
Product label
Lanyard
Green/Red LED
Trigger button
Power button*
Battery LED (Green/Yellow/Red)
Bluetooth LED (Blue)
Pins for
charging
cradle
Direct Current

1. Attach the Lanyard (optional)
Detach the string loop of the tether from the lanyard. Then feed the
string loop through the slot. Pull tight so the string loop is secure,
reattach the string loop to the tether from the Lanyard.
SCANNER SETUP
6

The scanner must be fully charged before rst use. Please allow 6 hours
uninterrupted charging for the initial battery charge.
For the Scanner, lift the rubber ap to access the power connector.
• Red LED = Charging
• Green LED = Fully charged
Important: Charging from a computer USB port is not reliable and
not recommended.
Battery warning: Do not remove the pre-installed battery.
The DuraScan contains a rechargable lithium-ion battery.
The battery may be replaced with a Socket Mobile battery
replacement kit. See socketmobile.com for replacement battery.
See other battery warning at pg. 39
6 Hours
CHARGE THE BATTERY
7

Battery charger warning: Only use the dedicated charger
provided for this unit. See more battery charger warnings at pg. 41
Charging with Cradle or QX Stand is
optional (available separately).
OPTIONAL CHARGING ACCESSORIES
8
Charging Cradle QX Stand

Powering On:
Press and hold down the small
power button until the LED turns
blue and the scanner beeps twice
(low-high).
Powering Off/ Disconnecting:
Press and hold down the small
power button until the scanner
beeps twice (high-low).
The scanner can power off
automatically if it is not connected
within 5 minutes and it is
connected within 2 hours of
inactivity.
POWERING ON/OFF
Power button
9

1D Barcode
Aim the scan beam straight
across the entire barcode.
2D Barcode
Aim at the center.
Scanning Barcodes
1. Hold the scanner a few inches from the barcode.
2. Aim, press and hold the trigger button.
By default, the scanner will beep, vibrate, and the LED will ash green
to conrm successful scan.
Caution: Do not stare directly into the LED beam.
SCANNING BARCODES
Trigger button
10

Connect your scanner using one of the following Bluetooth connection
modes:
Bluetooth Connection Proles
Bluetooth Mode Description
Basic Mode (HID)
(Default)*
Human Interface
Device Prole
• “NO” software installation needed
• Connects to most devices
• Good for barcodes containing small amounts of
data
• Scanner appears like a keyboard to host device
Application Mode
(SPP)
Serial Port Prole
• Software installation required
• More efcient and reliable data communications
for barcodes containing lots of data
Application Mode
(MFi-SPP)
Apple Specic
Serial Prole
• Must use with an App developed to work with
iOS devices
• Apple MFI tested and certied
• If you have an application that supports Socket
Mobile Scanners this is the mode you want to use
*By default, the scanner is set to Basic Mode (HID).
BLUETOOTH CONNECTION MODES
11

Operating System Connection Options
Operating
Systems
(OS)
Devices
Bluetooth
HID
Support
Bluetooth
SPP
Support
Bluetooth
Apple
Serial
Specic
(MFi Mode)
Android Android 2.1 &later Yes Yes N/A
Apple iOS iPod, iPhone, &
iPad Yes N/A Yes
Windows
Mobile
Windows Mobile
6.x Yes Yes N/A
Windows PC Windows 7, 8, 10 Yes Yes N/A
Mac OS
Mac OS X 10.4 to
10.X
Mac Books, Mac
Mini, &iMac
Yes No N/A
Note: To switch from one mode to the other you must remove the
pairing information from both devices - host computer and the scanner.
(see unpairing procedure on page 21)
12
BLUETOOTH CONNECTION MODES

Android: Connect Android Device in Basic Mode (HID)
1. Power on the scanner. Make sure the scanner is
discoverable (unpaired).
2. Touch Home | Menu | Settings | Wireless &Networks |
Bluetooth settings
3. Make sure the device has Bluetooth “On” and scan for devices.
4. In the list of found devices, select Socket scanner [xxxxxx]. Tap Pair.
5. The scanner will connect to the Android device.
6. The scanner will beep once after it has connected and is ready to scan
barcodes.
BASIC MODE
13

Apple: Connect Apple iOS Device or Mac OS Device Basic Mode (HID)
In this mode the scanner works and behaves just like a keyboard.
Therefore, scanner will work with Safari, Notes, and any other
applications that supports an active cursor.
1. Power on the scanner. Make sure the scanner is
discoverable (unpaired).
2. Start a Bluetooth device search.
• iOS: Tap Settings | General | Bluetooth. Turn on Bluetooth.
A Bluetooth device search will begin.
• Mac OS: Click System Preferences | Internet &Wireless | Bluetooth.
In Bluetooth preferences, select the On checkbox. Click Set up New
Device... A Bluetooth device search will begin.
3. In the device list, tap on Scanner [xxxxxx]. Tap Pair.
4. The Scanner will connect to the Apple device.
5. The Scanner will beep once after it has connected and is ready to scan
barcodes.
14
BASIC MODE

Windows: Connect Windows PC
Power on the Scanner. Make sure the Scanner is discoverable (unpaired).
1. Use your computer’s Bluetooth Settings to connect to the Scanner.
2. Open Devices and Printers and select “Add a device”.
3. In the device list, select Socket Scanner [xxxxxx]. Click Next.
4. If a passkey is requested, enter 0000 (four zeroes). Click OK.
Or Pair Now.
5. Follow the remaining screens to complete the wizard.
Note: On some computers the Scanner will have to be congured as Basic
Mode (HID) Peripheral. If not successful, scan this special barcode and
repeat the steps above.
BASIC MODE
15

Windows: Connect Windows PC as a Basic Mode (HID) Peripheral
1. Power on the Scanner and scan this barcode. The Scanner will beep 3
times.
2. Turn on Bluetooth on your PDA or PC and start a device search.
Make sure it is discoverable.
3. Select Socket Scanner. If prompted for a passkey, enter 0000
(four zeroes). If prompted to select services, select Input Device.
4. After the Scanner connects and is ready to scan barcodes, it will beep
once.
Now you are ready to scan barcodes!
To connect to a new device or use a different prole (mode) on the
same device, you must rst unpair the Scanner See page 21.
16
WINDOWS BASIC MODE (PERIPHERALS)

Connect Android or Windows Mobile Device:
Highly recommended, allows two-way communications with Android,
Windows and Mobile Devices. SocketScan 10 software installation
required.
1. Power on the Scanner and scan this barcode. The Scanner will beep 3
times. Make sure the Scanner is discoverable (unpaired).
2. Turn Bluetooth on for your device. Go to Settings > Bluetooth. A
Bluetooth Devices search will begin.
3. Tap Socket Scanner[xxxxxx] in the list of Devices found. After a
few seconds the “Not Paired” status will change to “Connected” or
“Paired” and the Scanner Blue LED will start blinking every 3 seconds
conrming the connection.
You are now ready to scan barcodes using your Scanner-enabled
Application.
APPLICATION MODE (SPP)
17

Connect Android device in Application Mode (SPP) using EZ Pair
1. Go to Google Play Store, search for “SocketScan 10”.
2. Download &install. Follow the on screen instructions.
Note: If prompted, allow the app to access your Bluetooth settings / USB
storage / SD card / Coarse location.
3. Make sure Bluetooth is turned on.
4. Open SocketScan 10 application.
5. When prompted to set SocketScan 10 as the keyboard language, tap
Back .
6. Go to Settings on Android device / Language and Input
7. Under Keyboard Settings, select SocketScan 10.
8. Open SocketScan 10 on your device.
9. When prompted to enable SocketScan 10 as Input Method,
tap Back .
10. Tap the Menu icon, then select Input Method.
11. On the next screen, select SocketScan 10 as input method.
12. Power on the Scanner. Make sure the Scanner is discoverable
(unpaired).
13. In SocketScan 10, tap the Menu icon then select Socket EZ Pair.
14. Scan the barcode on the screen to switch or set your scanner in
Application Mode (SPP). The Scanner will beep 3 times.
18
APPLICATION MODE (SPP)

Connect Android device in Application Mode (SPP)
15. Select [On screen] button.
16. On the next screen, tap on the 7Qi or 7Xi button that is appropriate
for your scanner button.
17. Scan the barcode on the screen. The Scanner will beep 3 times.
18. When notied of a pairing request, swipe the notication icon down
then tap Pairing request.
19. On the next screen, tap Pair.
20. The Scanner will beep once to indicate connected state and is ready
to scan barcodes. Tap Back to close Socket EZ Pair.
21. If you are connecting a scanner which is not registered, a Scanner
registration icon will appear on top of the screen. Swipe the icon
down to open the registration pages. Follow the instructions to
register your Scanner. Socket Mobile highly recommends that all
customers register their products, but registration is not necessary.
Now you are ready to scan barcodes!
Note: If you are unable to scan the barcode on screen, please use the
alternative Bluetooth Method to connect the Scanner; refer to the User
Guide at Socket Mobile’s support web page.
APPLICATION MODE (SPP)
19

Connect Windows PC in Application Mode (SPP)
Note: Make sure you have administrative privileges.
1. Download the latest SocketScan 10 software from Socket Mobile’s
support web page.
2. Follow the on-screen instructions to install the software.
3. In SocketScan 10 Settings, select an incoming Bluetooth serial COM
port.
Note: If there is none please click Ports to create at least one new
incoming COM port in Bluetooth settings.
4. Click Finish.
20
WINDOWS PC - APPLICATION MODE