Sodex Sport S14633 User manual

DETAILS
SODEX INTERNATIONAL
18 rue de l’Avenir - Bât. 224
14650 CARPIQUET
Tel : + 33 (0) 2.31.53.78.70
Email: [email protected]
DESCRIPTION
Steel structure
Plastified
CONFORM
European standard
NF EN 1270
Decree
SPORT’S LAW 2007
PRODUCT SHEET
MOBILE BASKETBALL GOAL
OFFSET :1.6M
PRODUCT REF :S14633 UNIT
SPORT’S LAW 2007
According to the decree above, for the first installation the goal must be tested like below :
Put a vertical and static charge of 320 kg, at the jonction of the pannel and the basket , at 0.20m of the ground, du-
ring one minute.
During the first installation, this stability and solidity test is compulsory.
Every time that the equipment is assembled, a visual check of the stability and solidity must be realized.
The owner must regularly check the condition of the product.
MAINTENANCE
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufactu-
rer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
If the forecast planned a bad weather (strong wind,…), the goal should be removed from the sheaths and
put on the ground.
WARRANTY
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to
be done within the legal period of the reception of the material. The warranty will not apply to:
- all degradation during the transport.
- all degradation due to use differing from which was intended.
- all degradation due to poor maintenance.
- any defect claimed after the end of the legal period.
- any damaged due to a faulty installation and assembly of the module
THIS PRODUCT HAS BEEN BUILT AND DESIGNED ACCORDING TO THE FRENCH AND EUROPEAN STANDARD NF EN 1270

2
FIXATION AND SEALING
There is two possibilities for the fixation of this basketball goal :
- Option A: Using counterweights located at the back (390kg min)
- Option B: Ground fixation
120mm
Screws M16x300
threaded sockets M16x120mm
Sol
920mm To fix the goal realize two holes in the ground
following the written dimensions.
920mm
3700mm
1600mm
Field limit
Holes for the sealing.
1200mm

3
Always drill the panel from the front side.
Drill a first hole with a bit of 6mm of diametre then do it again with a bit of
12mm of diametre. Start by drill the two holes on the top.
For outside using, it’s necessary to put some silicone around the hole to
protect them from water.
Put the panel on it support, check the height and then put a mark for the
drill of the last holes.
NECESSARY TOOLS (NOT INCLUDED)
Drill Silicone
DRILLING OF THE PANEL

4
ASSEMBLY
NECESSARY TOOLS (NOT INCLUDED)
.
INCLUDED ITEMS
Wrench 17 Wrench 19 Wrench 22
x6
Nuts M12
x24
Washers M10
x6
Nuts M10
x12
Nuts M14
x12
Washers M12
x20
Washers M14
x6
Nuts M16
x6
Screws M16x40
x6
Washers M16
x2
Screws M10x50
X4
Lock washers M14
x8
Screws M14x40
x6
Screws M12x40
x4
Screws M10x40
x4
Screws M14x30
1– ASSEMBLY OF THE BACK SUPPORT (x1)
Vis M16x40
Rondelles M16
NECESSARY
ITEMS
x2
Screws M16x40
x2
Washers M16
x6
Locknuts M10

5
ASSEMBLY
NECESSARY
ITEMS
NECESSARY
ITEMS
2– ASSEMBLY OF THE FRONT SUPPORT (x1)
Screws M16x40
Washers M16
x4
Screws M16x40
x4
Washers M16
3– ASSEMBLY OF THE REINFORCING BAR (x1)
Screw M10x70
Washers M10
Nut M10 Do this step twice
x4
Washers M10
x2
Screw M10x70
x2
Nuts M10

6
ASSEMBLY
4– ASSEMBLY OF THE UPPER PART (x1)
NECESSARY
ITEMS
x8
Screws M14x40
x16
Washers M14
Screws M14x40
Washers M14
Nuts M14
5– ASSEMBLY OF THE OFFSET (x1)
NECESSARY
ITEMS
Screws M12x40
washers M12
nuts M12
x6
Screws M12x40
x6
Nuts M12
x12
Washers M12

7
ASSEMBLY
6– ASSEMBLY OF THE MOUNTING PLATE (x1)
7- ASSEMBLY OF THE BASKET AND PANEL (x1)
NECESSARY
ITEMS
NECESSARY
ITEMS
x4
Screws M10x40
x12
Washers M10
x4
Vis M14x30
X4
Rondelles M14
Only half of the screws are show there.
x2
Screws M10x50
X4
Rondelles de blocage M14
Screws M14x30
washers M14
lock washers M14
Screws M10x50
washers M10
locknuts M10
Screws M10x40
washers M10
locknuts M10
x6
Locknuts M10

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg) Dim. (mm)
A1 AMain frame 1 Plastic
bubbles+cardboa
rd 5 layers
A2 AFront support 1Plastic
bubbles+cardboa
rd 5 layers
A3 ABack support 1 Plastic
bubbles+cardboa
rd 5 layers
A4 AReinforcing bar 1 Plastic
bubbles+cardboa
rd 5 layers
A5 S14522 IPanel 1Plastic
bubbles+cardboa
rd 5 layers
A6 S14333O
S14850 BBasket + net 1 + 1 Plastic
bubbles+cardboa
rd 5 layers
A7 Upper part 1Plastic
bubbles+cardboa
rd 5 layers
A8 Offset part 1Plastic
bubbles+cardboa
rd 5 layers
A9 Telescopic tube D et G 1 + 1 Plastic
bubbles+cardboa
rd 5 layers
A10 Mounting plate 1Plastic
bubbles+cardboa
rd 5 layers
PRE-ASSEMBLED ACCESSORIES
Package
N° Designation Description Qty Note
A2 Sticker
A1 Adaptable feets 4
A1 Wheels 4
A1 Screws M8x25 +
washers M10 + nuts
M10 16 + 32 + 16
PACKING LIST
BASKET MOBILE BASKETBALL GOAL
OFFSET :1.6M
PRODUCT REF S14633 Index A UNIT

ACCESSORIES PUT IN CLEAR PVC BAG
Package Designation Description Qty Note
A2 +
A3 +
A7
Screws M14x40 +
washers M14 + nuts
M14 8 + 16 + 8 Fix the upper part to
the supports
A7 +
A8
Screws M12x40 +
washers M14 + nuts
M14 6 + 12 + 6 Fix the offset part
A8 +
A9
Screws M14x30 +
washers M14 + nuts
M14 4 + 4 + 4 Fix the mouting plate
A5 +
A6 +
A10
Screws M10x40 +
washers M10 + lock-
nuts M10 4 + 8 + 4 Fix the panel and the
basket to the attach-
ment plate
A1 +
A2 +A3
Screws M16x40 +
washers M16 + nuts
M16 6 + 6 + 6 Fix the front and back
support together
A2 +
A3 +
A4
Screws M10x70 +
washers M10 + nuts
M10 2 + 2 + 2 Fix the reinforcing bar
A5 +
A10
Screws M10x50 +
washers M10 + lock-
nuts M10 2 + 4 + 2 Fix the panel to the
mounting plate
VISA PACKING DEPARTMENT DATE :
PACKING LIST
BASKET MOBILE BASKETBALL GOAL
OFFSET :1.6M
PRODUCT REF S14633 Index A UNIT