Solaris LOCOR User manual

8778002
Released January 82018
SOLARIS LOCOR® RECESSED MECHANICAL HARD WOUND ROLL TOWEL DISPENSER USER GUIDE (SKU NUMBERS D68012-A)
The LoCor Recessed Mechanical Hard Wound Roll Towel Dispenser is designed to be mounted into the wall or inside a recessed cabinet on the wall to yield
maximum space in the busy bathroom environment. The dispenser provides hands-free and battery-free operation for paper dispensing and offers an elegant
stainless steel appearance.
The dispenser is designed for an opening of 10 5/8” Width x 15 1/8” Length x 4” Depth.
TABLE OF CONTENT
I. Dispenser Installation Instruction …………………………………………………………………………………………………………. Page 2
1. Install Directly into the Wall – Using Cover Panel …………………………………..……….………….…………… Page 2
2. Install into Existing Recessed Cabinets on the Wall - Using Filler Panels ……………..……….……….…. Page 4
2a. Use Insert Filler Panel ………………………………………………………….……………….……………. Page 5
2b. Use Hanging Filler Panel ……………………….……………………………………………………………. Page 5
II. Changing Mounting Side of Cover ………………………………………………………………………………………………………….. Page 7
III. Roll Support Installation ………………………………………………………………………………………………………………………… Page 8
1. For 7” Width Solaris LoCor Paper Towel SKU Numbers 46897, 46989, 46899, 46902 ………………. Page 8
2. For 8” Width Solaris LoCor Paper Towel SKU Numbers 46896, 46901 …………………………………….. Page 8
IV. Paper Loading and Start Up …………………………………………………………………………………………………………………… Page 9
V. Failure Diagnostics ………………………………………………………………………………………………………………………………… Page 9
1
Outer dimension is 18.17" x 14.67" x 10.97", weighs approximately 8.7 lbs.

8778002
Released January 82018
I. DISPENSER INSTALLATION INSTRUCTION
1. Install Directly into the Wall – Use Cover Panel
Hardware provided with the dispenser:
oKey
o(4) Screws #10 x 1”L, Phillips Head
o(4) Wall Anchors
Tools and materials required (not provided):
-Stud Finder
-Pencil
-Tape Measure
-Level
-Knife or Saw (to cut drywall)
-Powered Screwdriver with Phillips Head and 1/4" Hex Head Drive
-Cotton Gloves
-(2) Studs 2” x 4” x 12”L
-(6) Screws #10 x 1 1/2”L, Phillips Head
Step 1: Dispenser Location
Determine the location of the dispenser to be mounted. Ensure there will be
no interference during the opening and closing of the cover or when paper is
dispensed at the bottom of the dispenser.
Step 2: Studs’ Location
Use a Stud Finder to find the location of the two studs on both sides of the
area where the dispenser will be mounted. Mark the locations of the studs.
Step 3: Cut the Opening on Drywall
Knowing the studs’ location, the dispenser should be mounted roughly in the
middle, between the two studs. The bottom of the dispenser should be 48
inches from the floor.
To install the dispenser into the wall, it is required to cut an opening of
10 5/8” W x 15 1/8”L on the drywall.
Recommend to use a pencil outlining the opening before cutting into the
drywall:
-Using a tape measure, place a mark of 48” from the floor. Then use a
level to draw a horizontal line from the mark. This is the bottom line
of the opening.
-Using a tape measure, place a mark of 15 1/8” from the bottom line
drawn from the last step. Then use a level to draw a horizontal line
from the mark. This is the top line of the opening.
-Use the level to draw two vertical lines to connect the top and
bottom lines. These two lines should be 10 5/8” apart from each
other. These two lines should be roughly in the middle, between the
two studs.
Now use a knife or a saw to carefully cut the opening out of the drywall.
See Figure 1 for more details.
2
10 5/8"
15 1/8"
48"
Floor
Figure 1.

8778002
Released January 82018
Step 4: Install the Two Supporting Studs
Install thetwostuds(2” x 4” x 12”L) onthe left side and right side ofthe
opening, behind the drywall as showed in Figure 2.
Drive three #10 x 1 1/2"L screws through the drywall into each studs on both
sides (total of six screws to be used). Note that the location of these screws
should be different to the location of the mounting holes on the left and right
side of the dispenser. See Figures 3 for more details.
Step 5: Install the Cover Panel and the Dispenser into the Wall
Remove the protecting film on the outside of the panel. Recommend to put
the cotton glove on the one hand that is used to hold the panel to avoid
finger prints. The other hand that is used to peel the film will not need glove.
Carefully place the dispenser into the big opening on the panel. Then install
the assembly (of the cover and the panel together) into the opening on the
wall. Slide the dispenser all the way in; ensure there is no gap between the
panel and the wall.
Use the key (provided) toopen the cover. Drive four #10screws (provided)
into the mounting holes on the left and right sides ofthe dispenser to
secure the dispenser tothe studs that were mounted instep 4.
See Figure 3 formore details.
The dispenser is now ready for Roll Support installation and paper loading.
3
Figure 2.
Figure 3.
the mounting
screws should not
be interenced with
the stud-screws
which are installed
in step 4.
COVER PANEL

8778002
Released January 82018
2. Install into Existing Recessed Cabinets on the Wall – Use Filler
Panels
Tools and materials required (not provided):
-Power Drill with:
oPhillips Head Drive
o1/4” Hex Head Drive
o1/8” Drill Bit
-Marker
-Cotton Gloves
-Other tools may be required, depends on the type of the existing
dispenser in the recessed cabinet
Step 1: Remove the Existing Dispenser from the Recessed Cabinet
Open the cover of the existing dispenser and remove the paper towel (if it is
in present) to examine whether the dispenser was secured in the cabinet by
screws/nuts, rivets or by spot welding.
*If the existing dispenser is secured by screws, use the power drill with the
Phillips Head Drive to loosen the screws to remove the dispenser out of the
cabinet.
* If the existing dispenser is secured by nuts, use the appropriate socket to
loosen the nuts to remove the dispenser out of the unit.
* If the existing dispenser has the cover riveted or spot welded to the
recessed cabinet, use the power drill with the 1/8” drill-bit to drill out the
rivets and spot-welds inside of the dispenser. Then carefully use a hammer
and a chisel to separate the hinge side of the cover from the cabinet frame.
See Figure 5 for more details.
Here are some examples of the existing recessed dispensers:
Recessed Paper Towel Dispenser – secured by screws/nuts
Recessed Paper Towel Dispenser – secured by spot welds
Open the cover and loosen
screws/nuts on the sides to
remove the existing
dispenser
Use a hammer and a chisel to
separate the hinge side of the
cover from the cabinet frame.
Use power drill and 1/8” drill bit todrill out
the rivets or spot welds (from the inside of
the existing dispenser).
4
Figure 4.
Figure 5.

Step 2: Filler Panel Installation
a. Use Insert Filler Panel
Hardware provided with the Insert Filler Panel:
o(4) Screws #8 x 3/4”L, Hex Head
o(4) Screws #6 x 1 1/4”L, Phillips Head
Do not remove the protecting film on the outside of the panel yet.
-Place the panel (with the protecting film still on) into the cabinet
with the top of the panel to be in the contact with the top of the
cabinet.
-Note that there are two mounting holes on each of the left and right
sides of the panel. Use the marker to mark the holes’ locations.
Carefully remove the panel out of the cabinet.
-Use the power drill with the 1/8” drill-bit to drill four holes at the
marks. Each hole should be roughly 1-inch deep.
-Remove the protecting film on the outside of the panel. Recommend
to put the cotton glove on the one hand that is used to hold the
panel to avoid finger prints. The other hand that is used to peel the
film will not need glove.
-Carefully slide the panel into the cabinet. Drive four #8 x 3/4”L Hex
Head screws (provided) into the mounting holes on the left and right
sides of the panel to secure the panel to the cabinet.
5
Figure 6.
b. Use Hanging Filler Panel
Hardware provided with the Hanging Filler Panel:
o(4) Screws #6 x 1 1/4”L, Phillips Head
o(3) Double Sided Tape Strips
Remove the protecting film on the outside of the panel. Recommend to put
the cotton glove on the one hand that is used to hold the panel to avoid
finger prints. The other hand that is used to peel the film will not need glove.
Use two double-sided tape strips (provided).
-Remove the backings on one side of the tape and place them with
the adhesive side onto the bezel as showed in Figure 7. Keep the
backings remaining on the front face of the tape.
-Loosen the screws that were used to secure the cabinet to the studs
(typically these screws locate on the left and right sides of the
cabinet). Store these screws for later use. Then pull the top part of
the cabinet out slightly, just enough to hang the panel on the top
bezel of the cabinet.
-After the top of the panel is hung on the bezel, remove the backings
of the tape and then press the panel onto the tape to secure the
placement of the panel.
-Re-install the mounting screws on the left and right sides the cabinet
to complete the panel installation.
Figure 7.
BEZEL
TOP OF THE PANEL
double sided
tape

8778002
Released January 82018
6
Step 3: Dispenser Installation
Hardware provided with the dispenser:
oKey
o(4) Screws #10 x 1”L, Phillips Head
o(4) Wall Anchors
Through the front opening of the panel, slide the dispenser all the way in,
make sure that the back of the dispenser is in contact evenly with the back of
the cabinet. There are two options to secure the dispenser:
Option 1: Drive the four #10 screws (provided) into the mounting
holes on the back ofthe dispenser tosecure the dispenser tothe
cabinet.
Caution Note: The length of the #10 screwsis1 inch, which may be
longer than the thickness ofthe drywall on the back ofthe cabinet.
Ifitisnot acceptable, please use option 2.
Option 2:Drive the four #6 screws (provided) into the front
mounting holes on the housing tosecure the dispenser tothe
panel.
The dispenser is now ready for Roll Support installation and paper loading. Figure 8.

The cover is designed to be mounted on either left or right side of the
housing. Manufacturing setting is left-side mounting. To change to right-side
mounting, follow steps 1 - 5:
Step 1:Remove Hinge Pins (Top & Bottom)
First remove the e-clips atthe end of the pins. Then remove the pins.
Step 2:Remove the Removable Hinges (Top & Bottom)
First remove the screws. Then remove the hinges.
Step 3: Remove the Door Seal Plug
Flex one of the legs to push the door plug out.
Step 4:Remove the Lock
First remove the screws. Then remove the lock.
Step 5:Reverse steps1 - 4 and switch side when install the components back
on the cover. Note that the Hinges and Pins should be installed on the same
side that the cover is desired to be mounted on. The Lock should be installed
on the opposite side of the Hinges. And the Plug should be installed on the
same side as the Hinges.
See Figure 9 for more details.
Bottom Hinge
Pin
Removable Hinge
E-clip
Top Hinge
E-clip
Removable Hinge
Pin
Lock
Screw
Lock
Door Seal Plug
Flex one of
the three legs
to push the
plug out
Screw
8778002
Released January 82018
7
II.CHANGING MOUNTING SIDE OF COVER
Figure 9.

The dispenser isdesigned to accept both the 7”and 8” wide LoCor Roll
Towels. Itisvery important toidentify the width of the paper roll before
installing the Roll Supports:
SKU Numbers for 7”Width LoCor Paper Towel:46897, 46898, 46899, 46902
SKU Numbers for 8”Width LoCor Paper Towel:46896, 46901
After identifying the paper roll width, install the Roll Supports from the
supplied kit included with the package:
- Two Roll Supports
- Four Screws
- Roll Support Installation Instruction Sheet
7" WIDTH ROLL SUPPORTS 8" WIDTH ROLL SUPPORTS
8778002
Released January 82018
8
III.ROLL SUPPORTS INSTALLATION
Note: Need to use a Phillips Head Screwdriver for the installtion. Use four
screws (provided) to install the Roll Supports into the correct places on the
back of the housing. See Figure 10 for more details.
Figure 10.

For use with LoCor paper towels only (SKU numbers 46896, 46897, 46898,
46899, 46901 and 46902). Other types of paper are not acceptable.
Paper should be loaded with paper “tail” unwinding from the front of the
roll. After the paper roll isloaded correctly into the dispenser,pull the paper
“tail” downward and tuck itunder the tension roller.Turn the assist wheel in
the clockwise direction until the paper “tail” comes out at the bottom of the
dispenser.
The dispenser isnowready for
dispensing. Simply pull the paper
“tail” at the bottom ofthe
dispenser to obtain paper.
a. If there is no paper “tail” at the bottom of the dispenser, turn the assist
wheel in the clockwise direction until the “tail” comes out.
If there is still no paper “tail” after two rotations of the assist wheel, open
the dispenser cover for further examination.
If the assist wheel gets stuck, do not force it to turn. Open the dispenser
cover for further examination.
b. If the dispenser performs poorly (not cutting or only partially cutting
paper), open the dispenser cover for further examination:
Check to ensure that paper roll is loaded correctly
Check to ensure that the Roll Supports are installed at the correct places.
Re-load the paper roll: first tear the paper from the roll at the section
before the paper enters the mechanism, then remove the remaining paper
out the bottome of the dispenser. Turn the assist wheel several times to
insure that the mechanism ismoving smoothly. Next, re-load the paper as
instructed in section 4 – Paper Roll Loading andStart-up.
For further assistance, please contact technical dispenser support at (920) 940-8904
Ensure the paper tail is in the
opening on the cover for
proper dispensing.
8778002
Released January 82018
9
IV.PAPER ROLL LOADING AND START-UP V.DIAGNOSTICS
Figure 11.
Table of contents
Other Solaris Dispenser manuals
Popular Dispenser manuals by other brands

Westomatic
Westomatic Primo Compact Install, Clean & Fill

Stoelting
Stoelting CW5-37A Technical handbook

lancer
lancer CoCo Fountain Tower Operation manual

Royal Catering
Royal Catering RCSD-4 user manual

Lafferty
Lafferty Sentinel 976956-L Installation & operation instructions

Georgia Pacific
Georgia Pacific ActiveAire 56764 reference guide