Solight 1L71 User manual

Thank you for purchasing our wireless doorbell with power outlet.The set consists of a bell button (transmitter) and a bell (receiver). The doorbell
is designed for permanent connection to a 230 V AC/50 Hz power supply. The transmission between the button and the doorbell is via radio waves
with a frequency of 433.92 MHz. The range depends on local conditions and can reach up to 250 m in open spaces without interference. The set has
a so-called pairing function (Learning code) - the button is able to generate its own pairing code, which is received by the doorbell and stored in its
memory. The set can thus be expanded with additional transmitters or receivers. The pairing function also prevents the set from affecting
neighbouring bells. For proper use, read the instruction manual.
Technical parameters
Doorbell power supply
max. AC 250V,50Hz
Continuous electric socket
max. AC 250V/16A, 3680W/230V~
Volume
4 modes, 20-80 dB
Working frequency
433.92 MHz
Receiver standby power
<0.5W
Transmitter operating power
<10mW
Melody
58 melodies
Reach
Up to 250m in open space
Transmitter Coverage
IP55
Power button
CR2032 battery (included)
Installation
1. Tear off one side of the double-sided adhesive tape and stick it to the underside of the button (transmitter).
2. Tear off the other side of the double-sided adhesive tape.
3. Select a suitable place and stick the button. If a stronger fixing is needed, use dowels and screws - open the button (see battery replacement),
drill holes in the marked circular slots on the inside of the button cover and screw it to the base. Then cover the other part of the button and
press the two parts together.
4. Connect the doorbell (receiver) to an electrical socket
5. Select the melody, volume or type of signaling
Replacing the battery
Using a flathead screwdriver push into the groove of the joint on the short side of the button and open the cover . Insert the CR2032 battery,
observing the marked polarity. Then close the cover.
"Code Learning" function
The device has already been paired in production. If you need to change the transmitter, increase or decrease the number of bells or buttons in a
group, follow the steps below:
1. Pairing
Press and hold the button for "Setting the light/sound signalization" until the device emits a bird whistle sound. Then, within 30 seconds, press
the button on the transmitter. If the bell rings, the pairing is successful. If the bell does not ring, press the transmitter again until pairing is
successful. To pair multiple transmitters, repeat the above operation. A maximum of 8 buttons can be paired to one doorbell. One button can
be paired with a maximum of 20 bells, and a different melody can be set on each bell.
2. Cancel pairing
Press and hold the "Setting the light/sound signalization" button for about 10 seconds until the chime (ding dong) sounds twice. This cancels
the pairing. Before the sound of the bell (ding dong) there is usually a bird whistle - do not release the button at this time and wait for the ding
dong melody.
Notice
1. Do not disassemble or repair the equipment.
2. Operating range may be affected by environmental factors and nearby interference sources.
3. Proper use will effectively extend the life of the equipment.
4. Disconnect the receiver from the mains before cleaning. Use only a dry soft cloth for cleaning. If you use wet cleaning, use only cleaning agents
free of aggressive compounds and reagents and allow to dry thoroughly. Do not immerse the product in water! Protect the product from
contact with fluxes and places of high temperature.
EN 1L71
Wireless doorbell with electrical socket
Volume settings
Melody settings
Setting the light/sound signalization
1.
Ringing + light signalization
2.
Ringing only
3.
Only light signalization
4.
Continuous light signalization + ringing
Light
signalization
Electric
outlet

Troubleshooting:
If the receiver does not ring repeatedly after pressing the button on the transmitter, check:
- whether the distance between the transmitter and the receiver is too large
- that there are no strong sources of signal interference between the transmitter and receiver (radio and wireless networks, large metal objects,
reinforced concrete walls, etc.)
Solight Holding s.r.o., declares that the product complies with the requirements and provisions of Directive 2014/53/EU. The
equipment can be freely operated in the EU. The Declaration of Conformity can be found at www.solight.cz. The product can be
operated under general authorisation No.VO-R/10/05.2014-3
Producer: Solight Holding, s.r.o., Na Brně 1972, Hradec Králové 500 06, www.solight.cz