Soltech SOLTAB User manual

SOLTAB
INSTALLATION MANUAL
10W/1100LM
PLEASE READ AND FOLLOW INSTRUCTIONS FOR PROPER OPERATION
SAVE THIS MANUAL FOR FUTURE REFERENCE
NOTICE & WARNING
INSTALLATION
1. The SOLTAB will provide optimal usage where there is enough sunshine.
2. Please note the lighting time depends on sunshine duration and weather.
3. Built-in intelligent IC is with over-charge, over-discharge and over-voltage protection.
4. The lamp is equipped with an internal battery pack, which is replaceable. If needed, please
contact for correct new battery pack.
5. Non-professionsals please do not disassemble the lamp.
6. Please do not dispose the battery with household garbage to avoid explosion.
1. Take out of the whole lamp from package, confirm the installation location and wire
length. (Figure 1)
2. Use the card to measure hole position, then drill 4 holes of .3 in with 2.4 in depth. (Figure
2)
3. Fix expansion screw into the holes with a spare space. Then place Panel and Fixture.
(Figure 3)
4. Open the silicon cover at the bottom of the lamp, connect the wire from the solar panel to
the lamp and screw it tightly. (Figure 4)
5. Adjust the solar panel and LED lamp to the right position according to local latitude and
lighting direction. (Figure 5)
1. 2. 3. 4. 5.

DESIGNATION SOLTAB 10W
MODEL STL-TAB104WMBK
LED NOMINAL POWER 10W
LUMENS @5000K 1100LM
LITHIUM ION BATTERY 3.7V 7.2AH
SOLAR PANEL Mono-Crystalline 6V 10W
CRI >70
CASTING PC/Aluminum
PRODUCT SIZE (SOLAR
PANEL)
13.6x9.3x1.8IN
PRODUCT SIZE (LIGHT) 9.1x6.5x1.3IN
CCT 4000K
IP RATING IP65
BEAM ANGLE 90°
PIR SENSOR ANGLE/AREA 90°/ 16-26 ft
HOUSING COLOR Black
CHARGING TIME 7 Hours
OPERATION MODE 4 operating modes
OPERATING TEMP (NIGHT) -5°F to 113°F
CHARGING TEMP (DAY) 32°F to 149°F
SPECIFICATIONS
FEATURES
OPERATING MODES
ACCORDING TO THE CONNECTION OF THE LIGHT AND SOLAR PANEL,
THE LAMP WILL AUTOMATICALLY RECOGNIZE THE SENSOR MODE &
CONSTANT LIGHTING MODE & POWER BANK FUNCTION.
ZERO ELECTRICITY COST
RADAR INDUCTIVE/
CONSTANT LIGHT MODE
POWER BANK
Constant Lighting Mode
Integrated Power Bank
IP65 RATING
SOLAR POWERED
AUTO ON/OFF
BATTERY REPLACEABLE
MULTI WORKING MODES
On/Off Mode
Mode B3: Press for a 3rd time to turn off
Mode B2: Automatically turns on and remain 100% brightness(1100lm) for 5 hours. After 5 hours or
when battery capacity < 30% it turns to back to Mode B1.
USB Cable
(Not included)
USB Discharge:
5.0V/1.0A
DC-Micro Charge:
5.0V/1.0A
Mode B1: Automatically turns on full brightness (1100lm) when motion is detected in range ≤8m
and then turns to 5% brightness in 20 seconds of no motion.
5 Hours
Under this work mode, the lamp will automatically turn on at night and will turn off daytime.
Under this work model, the Radar sensor & Photocell induction will not work.
Mode A1: Press 1st time for 50% Constant Brightness.
Mode A2: Press for a 2nd time for 100% Constant Brightness.
Mode A3: Press for a 3rd time to turn off.
Mode A: Constant Lighting Mode (Lamp separate with Solar Panel)
Mode B: Sensor Mode (Lamp body connected to Solar Panel)
Additonal Power Bank Function