Somerset SDP-747 User manual

SDP-747 & SDP-747D
OPERATIONS MANUAL
SOMERSET IN DUSTR IES
1 ESQUIRE RD. •N. BILLERICA, MA 01862 • USA •978-667-3355 • s omer s e t@s mr se t.com

UNCRATING AND INSTALLATION
After the outside straps are cut and the box is removed, cut the straps that
hold the unit on the wooden base.
Remove the unit from the base and secure it on top of a solid surface (table
or stand).
CAUTION:
• Verify table stability and make sure the dough press is not sliding.
Wipe off any dust collected during shipping.
Verify the height for the unit is ergonomically suitable for the user(s).
Connect the plug to a power outlet (that meets local electrical codes) as
specified by the power label (rear of unit).
SET UP
Dough thickness is a function of temperature and pressure.
The higher the temperature and time of pressure, the thinner the dough
Temperature Adjustments
SDP-747
Has a preset temperature setting at 150 degrees F (66 degrees C)
SDP-747D
Has a preset temperature setting at 250 degrees F (121 degrees C)
You can change the temperature setting (higher or lower) depending upon
your dough and the speed of your operation (the higher the temperature,
the faster the operation).
Actual platen temperature is displayed on the left side of the temperature
controller. Set up temperature is displayed on the right side of the
temperature controller.
To change the temperature on the controller, press and hold the blank
button (*) on the left of the controller and simultaneously press the
(^) or (v) keys to increase or decrease the controller to the desired
temperature.
Please contact the factory if you need assistance setting the controller.

DOUGH PRESS SERIES SDP-747D die replacing procedure
Swing the bottom platen away from the top platen.
Align the slot on the bottom platen with the mould’s and turn the mould 1/4
of a turn.
Remove the mold from bottom platen by turning it 1/4 of a turn..
• CAUTION: AVOID TOUCHING HOT PLATEN(S).
DOUGH PREPERATION
Dough must be round and its weight should reflect the diameter and
thickness required.
Dough should be room temperature (between 60 TO 70 degrees F (15.6 TO
22 degrees C) for best results.
SDP-747 OPERATION
Verify that the displayed temperature is the same as the set up
temperature.
Swing the bottom platen away from the top.
Spray the bottom and top platen surfaces with cooking oil.
Place the dough ball at the center of the bottom platen and spray the dough
ball with the oil.
Swing the bottom platen under the top, lower the arm and hold it for 1 to 5
seconds or until the dough is spread.
Lift the arm and swing the bottom platen away from the top.
Remove the dough from the bottom platen and repeat the same process for
the next piece of dough.
SDP-747D OPERATION
Verify that the displayed temperature is the same as the set up
temperature.
Swing the bottom platen (with the mold attached on it) away from the top
platen.
Spray the mold and the top platen plate with cooking oil.
Place the dough ball at the center of the mold and spray the dough ball
with the oil.
Swing the bottom platen under the top, lower the arm and hold it for 1 to 5
seconds or until the dough is spread.
Lift the arm and swing the bottom platen away from the top.
Hold/cut the slotted section on the mold with a plastic spatula.
Remove the dough from the bottom platen and repeat the same process for
the next piece of dough.

CLEANING
Turn unit OFF, and remove power cord from power outlet.
Let unit cool down to room temperature.
With a clean rag, wipe off platens, handle and other surfaces.
Do not use scouring pads or sharp objects to clean the platen surfaces.
Clean the Stainless Steel surfaces with a S.S. cleaner.
Do not submerge unit in water or other liquids for cleaning; do not use
inflammable spirits for cleaning this unit.
Plug the power cord into the power outlet after cleaning, the unit is ready
for use.
CAUTION: Do not place metallic objects or screen between the platens.
NOTE: This unit is maintenance free, do not apply any oil or grease on any
parts.
CAUTION: To remove the cylinder or work on the power assists
mechanism (P.A.M.), you must reduce the tension of the P.A.M. mechanism
by turning the tension bolt Counter-Clock Wise until there is no tension on
the P.A.M.
Contact the factory for this operation.

Front Panel Operation
Push
Up
to turn Power On
Push
Down
to turn Power Off
Hold Button
In
To Change Temperature
Push Buttons
To Change
Temperature
Up or Down

SOMERSET
SDP-747
SERVICE MANUAL
1 Esquire Road, North Billerica, MA
www.smrset.com
[phone]
INSPECTING THE LIMIT SWITCH AND HEATER
&
LEVELING THE PLATEN
Disconnect Electrical Plug, and allow Dough Press to Cool Down.
Loosen 3 set screws
Using 3/32” allen wrench.
It is recommended that an extended
Ball end allen wrench be used.
Page4of28
"THIS DRAWING AND SPECIFICATIONS ARE
THE EXCLUSIVE PROPERTY OF SOMERSET
INDUSTRIES INC. IT MAY NOT BE USED
OR REPRODUCED INWHOLE OR PART, NOR
MAY IT BE SENT TO ANY OTHER VENDOR
WITHOUT THE EXPRESS WRITTEN CONSENT
OF SOMERSET INDUSTRIES INC."
Author: GJH Date: 3/11/11
App’d: GJH Date: 3/11/11
REV
C

SOMERSET
SDP-747
SERVICE MANUAL
1 Esquire Road, North Billerica, MA
www.smrset.com
[phone]
Slide Ring Up Raise Cover Up
The use of a “Bungee” Cord
stretched over the top of the press
will help to hold the cover
while working on the top platen.
(Approx. 22”relaxed length)
Page5of28
"THIS DRAWING AND SPECIFICATIONS ARE
THE EXCLUSIVE PROPERTY OF SOMERSET
INDUSTRIES INC. IT MAY NOT BE USED
OR REPRODUCED INWHOLE OR PART, NOR
MAY IT BE SENT TO ANY OTHER VENDOR
WITHOUT THE EXPRESS WRITTEN CONSENT
OF SOMERSET INDUSTRIES INC."
Author: GJH Date: 3/11/11
App’d: GJH Date: 3/11/11
REV
C

SOMERSET
SDP-747
SERVICE MANUAL
1 Esquire Road, North Billerica, MA
www.smrset.com
[phone]
3 Large screws (circled) are for leveling,
and platen removal.
Page6of28
"THIS DRAWING AND SPECIFICATIONS ARE
THE EXCLUSIVE PROPERTY OF SOMERSET
INDUSTRIES INC. IT MAY NOT BE USED
OR REPRODUCED INWHOLE OR PART, NOR
MAY IT BE SENT TO ANY OTHER VENDOR
WITHOUT THE EXPRESS WRITTEN CONSENT
OF SOMERSET INDUSTRIES INC."
Author: GJH Date: 3/11/11
App’d: GJH Date: 3/11/11
REV
C

SOMERSET
SDP-747
SERVICE MANUAL
1 Esquire Road, North Billerica, MA
www.smrset.com
[phone]
Top Locking Bolt
(1/2”Wrench)
Bottom Adjusting Bolt
(5/8”Wrench)
At all 3 points:
Hold the “Bottom Adjusting”Bolt in place. DO NOT ALLOW THIS TO MOVE.
Loosen and remove the 3 “Top Locking”Bolts.
Raise the plate carefully, using the press handle, and Inspect the wiring, connections,
and limit switch.
To Re-Assemble, At all 3 points:
Hold the “Bottom Adjusting”Bolt in place. DO NOT ALLOW THIS TO MOVE.
Insert and tighten the 3 “Top Locking”Bolts, torque the bolts evenly, and insure
the platens are level when complete.
Page7of28
"THIS DRAWING AND SPECIFICATIONS ARE
THE EXCLUSIVE PROPERTY OF SOMERSET
INDUSTRIES INC. IT MAY NOT BE USED
OR REPRODUCED INWHOLE OR PART, NOR
MAY IT BE SENT TO ANY OTHER VENDOR
WITHOUT THE EXPRESS WRITTEN CONSENT
OF SOMERSET INDUSTRIES INC."
Author: GJH Date: 3/11/11
App’d: GJH Date: 3/11/11
REV
C

SOMERSET
SDP-747
SERVICE MANUAL
1 Esquire Road, North Billerica, MA
www.smrset.com
[phone]
Slide cover and ring
Down and tighten
3 screws securely
Page9of28
"THIS DRAWING AND SPECIFICATIONS ARE
THE EXCLUSIVE PROPERTY OF SOMERSET
INDUSTRIES INC. IT MAY NOT BE USED
OR REPRODUCED INWHOLE OR PART, NOR
MAY IT BE SENT TO ANY OTHER VENDOR
WITHOUT THE EXPRESS WRITTEN CONSENT
OF SOMERSET INDUSTRIES INC."
Author: GJH Date: 3/11/11
App’d: GJH Date: 3/11/11
REV
C

CLEANING:
1. TURN OFF MACHINE
2. ALLOW TO COOL DOWN
3. WIPE EXTERIOR OF MACHINE
4. REMOVE, CLEAN & SANITIZE ALL MOULDS
5. CLEAN UPPER & LOWER PLATEN WITH SOFT CLEAN CLOTH
6. WIPE DOWN STAINLESS EXTERIOR DAILY
Removing the moulds from the model CDR-747D Bottom Platten:
CONTACT FACTORY FOR HELP & Q UEST I ON S
SOMERSET INDUSTRIES 978-667-3355

31
REV
D 0747-PART A
D
71
8
C
8 7 6 5 4 3 2 1
REV DESCRIPTION CHG'D APP'D DATE
F 20
75 37 36
80 36
81
40
79 56
38 55
49 49 A
58 53 52
54 F
41
23 24
E
33
82
78
51
39 83
57
57 E
1 37 19
8 35
32 33 67
947
12
4 3 2
32 18
46
34
D
77
32
8 7 48
9
22
7 6
C
66
9
50 5
12
26 65
27
63
74
11
B 11
72 25
45
43
2
B
42 64
76 8 3
13
A
44 16
17 37
68 73 30
21 29
8
59
14 69
28 15
70
60 70
61 62
DO NOT SCALE DRAW ING SOMERSET
UNLESS OT HE RW I SE SP E C I F I ED:
DIM E N SIONS ARE I N I NCHES[ M I L L IM E T ER]
.XX .0 15 [ . 4]
.XXX .0 05 [ .13] FRACTIO NAL 1/32 [ . 8]
.XXXX .0005 [ .0 13] ANGULAR: 1
SOMERSET INDUSTRIES, INC. A
NORTH BILLERICA, MA 01862
T I TLE::
SDP-747 PART
PR OPRIETA R Y AND CON FIDENTIAL II NTTEERP R ETT DR AW IING PEER:
NA M E D AT E
30 10 2T HE
INF O R M A TI O N C O N TA IN E D IN T HIS
D RA W I N G AND ASS O CI A TE D CADDATA
FILE S IST HE SOL E P ROP E R T Y OF
ANSSII Y 14.5M -- 1982
M ATTEERII ALL
N/A
N/A
DRAW N
CHECKED
K S A VII TT SKI Y 0 2 /12/0 8
W LU NT 02 / 12/0 8 SIZE DW G.. NO.. REV
A
S OM E RS E T I N D U S T RI E S . IT MAY NOT
BE RE P R O D U C E D IN PA R T, OR AS A
W H O L E , OR SE N T T O ANY O T HE R V E N D O R,
FI NIISSH ENG APPR.. W LUNT 02 /12 /0 8 D 0747-PART
W I T H O U T T HE E X P RE S S WRITTE N
C O N S E NT OF S OM E R SE T I N D US T RI ES .
8 7 6 5 4 3 2
M FG APPR.. W LU NT 0 2 /12 //08
DATABA SE:SOLIDW ORKS Q.A.
SCALE: 1 :: 2 . 25
WEI GHT N/ A
1
SHEE T 1 O F 2

D 0747-PART
F
F
E
E
D
D
C
C
B
B
A
A
A
8
7
6
5
4
2
3
1
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 0747-121 ASSY, REINFORCEMENT 1
2 3000-201 WASHER, FLAT 3/8 16
3 3000-103 WASHER, LOCK SPLIT 3/8 14
4 3000-409 SCREW, 3/8-16X1 HEXHD SS 10
5 0747-039 BRACKET, FRAME TO SHELL LEFT 6
6 0747-043 BRACKET, FRAME TO SHELL RIGHT 4
7 3000-200 WASHER, FLAT 1/4 20
8 3000-106 WASHER, LOCK SPLIT 1/4 30
9 3000-404 SCREW, 1/4-20 X 3/4 HEXHD 24
10 3000-421 SCREW, 3/8-16 X 1-1/2 HEXHD 5
11 3000-102 WASHER, LOCK SPLIT 5/16 11
12 3000-413 SCREW, 5/16-18 X 1 1/2 HEXHD GR8 7
13 0747-102 BAR, FRONT 1
14 3000-105 WASHER, LOCK SPLIT 1/2 2
15 3000-437 SCREW, 1/2-13 X 1-1/2 HEXHD 2
16 0100-034 FOOT, 1.0 TALL X 1.125 DIA 4
17 4000-300 LEG TIP RUBBER 4
18 4000-122 PLUG, PLASTIC 2.5 DIA 747 FRAME 1
19 5000-611 DECAL, SDP 747 MAIN 1
20 0747-020 PANEL, COVER TOP 1
21 0747-048 PANEL, COVER BOTTOM 1
22 3000-305 NUT, FLANGE 5/16-18 10
23 3000-426 SCREW, 5/16-18 X 1-1/4 SHCS 3
24 0747-167 DOVETAIL, SPACER 1
25 0747-129 BUSHING, PLATEN LEVELING 3
26 0750-199 COVER, 18" PLATEN TOP 1
27 0747-218 INSULATION, COVER CUT TO SIZE 1
28 0747-103 POST, LOWER PLATEN 1
29 4000-312 WASHER, IGUS 1-3/4" ID 1
30 3000-432 SCREW, 1/4-20 X 1-1/2 SHCS 4
31 4000-554 BUSHING, W/SHDR GARLOCK HANDLE 2
32 4000-314 RING, RETAINING EXTERNAL 6
33 3000-205 WASHER, HANDLE PRESS 2 OD 1-1/16ID .047THK 4
34 0747-204 CAM SHAFT 1
35 0747-026 DISK, COVER CYLINDER 1
36 3000-101 WASHER, LOCK INT TOOTH #10 9
37 3000-402 SCREW, 10-32 X 3/8 TRUSS PH SS 11
38 0747-500 ELBOW, HANDLE RIGHT 1
39 0747-128 HANDLE, MAIN 747 1
40 0747-141 BLOCK, MTG C'BAL RIGHT 1
41 0747-144 BLOCK, C'BAL LEFT 1
42 0747-156 STUD, CENTER PLATEN SUPPORT 1
43 0747-124 STUD, BOTTOM PLATEN REST 4
44 4000-257 SPRING, COMPRESSION 747 PLATEN LEVEL 5
45 0747-197 COLLAR, CYLINDER UHMW 747 1
46 0747-109 COLLAR, CYLINDER 747 ALUM 1
47 3000-340 SCREW, 10-32 X 1/4 SET HEX 3
48 3000-303 NUT, FLANGE 1/4-20 1
49 3000-310 NUT, HEX 6-32 6
50 5000-279 BUSHING, CORD LOCK 1
51 5000-280 BUSHING, CORD 747 .565 HOLE 2
52 5000-401 CONTROLLER, TEMP CAL-3200 1
53 5000-200 SWITCH, ROCKER 110/220VAC 3 PRONG SPST 1
54 5000-196 COVER,SWITCH ROCKER 1
55 5000-152 RELAY,CRYDOM D2450G 1
56 5000-153 COVER, RELAY 1
57 5000-267 CLAMP, 5/16ID X 1/2 WIDE X .166DIA NYLON 4
58 0747-117 BRACKET, HEAT SINK 1
59 0747-044 WELDMENT,HORSESHOE 1
60 3000-428 SCREW, 1/4-20 X 3/4 HEX BUTTON HEAD 4
61 3000-410 SCREW, 1/4-20 X 1/2 HEXHD 2
62 3000-420 SCREW, 3/8-16 X 3/4 PAN HD SLOT 1
63 4000-405 KNOB, 2" DIA 3/8-16 1
64 0747-030 BRACKET, KNOB SUPPORT 1
65 5000-323 DECAL "DOUGH PRESS" 1
66 5000-326 DECAL, ETL, MODEL/SERIAL 1
67 5000-317 LABEL, NSF 1
68 0747-104 ROD, LWR PLATEN SPRT 2
69 0747-111 ROD, FRONT FRAME MTG 1
70 4000-558 BEARING, NEEDLE PLATEN SWING 1.75IDX2.125ODX1LG 2
71 4000-557 CAM FOLLOWER, 1 DIA 2
72 0747-602 WELDMENT, BLOCK REAR LEG 2
73 0747-216 CYLINDER WELDMENT 1
74 0747-604 ASSY, PLATEN UPR W/ SWITCH & T/C 120VAC 1
75 0747-146 COUNTERBALANCE #251, 1.044dia 1
76 0747-609 PLATEN, LOWER MACHINED 1
77 0747-010 FRAME, MAIN 747 1
78 0747-160 ASSY, DOVETAIL GEN III 1
79 0747-601 ASSY, HANDLE SHAFT, CAMS 1
80 3000-339 SCREW, 10-24 X 3/4 ROUND PH 2
81 0747-210 BRACKET, CB NO HOLE 1
82 0747-499 ELBOW, HANDLE LEFT 1
83 5000-241 CABLE 17" 1897C ALPHA W/2 FORK 1
126 3000-231 WASHER, LOCK SPLIT 1/4 GR8 12
A
R EV DES CR I P T I O N CHG'D APP'D D AT E
SOMERSET SOMERSET INDUSTRIES, INC.
DO NOT SC ALE DRAW ING
U NLESS O T HE R W I SE SP E C I F I ED :
DI M E N SI O N S A RE I N I NCHES [M IL LIM E T E R ]
T I TL E ::
NORTH BILLERICA, MA 01862
.XX .015 [ . 4 ]
.XXX .00 5 [ .13 ] FR ACT I O NAL 1/32 [ . 8]
.XXXX .0005 [ .0 13] ANGUL AR: 1
PR OPRI ET AR Y A ND CONFI DENT IA L II NTTEERPR ETT DR AW IING P EER:
NA M E D
AT E
SDP-747 PART
THE INF O R M A TI O N C O N TA I N E D I N T HIS
DRA WI N G AND A S S O CI A T E D C AD DA T A
FIL ES IST HE SOL E P ROP E R T Y OF
S OM E R S E T I N D U S T RI E S . IT M AY NOT
BE RE P R O D U C E D IN PA R T, O RAS A
W H O L E , OR SE NT T O ANY O T HE R V E N D O R,
W I T H O U T T HE E X P RE S S WRITTEN
C O N SE NT OF S OM E R SE T I N D U S T RI ES .
ANSSII Y 14. 5M -- 1982
M ATTEERII ALL
N/A
FI NIISSH
N/A
DR AWN
CHECKED
ENG APPR..
M FG APPR..
K S A VII TT SKI Y 0 2 /12 /0 8
W LUNT 02 / 12 /08 SI ZE DWG.. NO..
W LU NT 0 2 / 12 /08
W LUNT 0 2 /12 /0 8
REV
A
DATABASE:SOLIDWORKS
Q. A . SCALE: 1::1 WEI GHT N/ A SHEE T 2 OF 2
D 0747- PART
REV
A

REV
D 0747D-PART A
D
71
66
8 7 6 5 4 3 2 1
37 36 80 36
79 56 49 55 REV
A
49
DESCRIPTION CHG'D APP'D DATE
58 53 52
F 20 75 81 40 38 54 F
41
23 24
E
1
33
84
78
51
37
39 85
57
57 E
19
8
947
12
4 3 2
8 7
9
22
35
32 31 33 32
46
34
48
67 18
D
77
32
7 6
C 8
9
50 5
12
11
B 11
72 25
45
43
68 30
A
C
73 27 26 83 65
82
74 42 63
2
B
64
83
13 59 76 61 62
DO NOT SCALE DRAW ING SOMERSET INDUSTRIES, INC. A
44 16 21 29 14 69 70 U NLESS
OT HE RW I SE SP E C I F I ED: SOMERSETNORTH BILLER ICA, MA 01862
DIM E N SIONS ARE I N I NCHES[ M I L L IM E T E R ] T I TL E ::
. X X .0 15 [ . 4]
17 37 8 28 15 60 70 .XXX .0 05 [ .13] FRACTIO NAL 1/32 [ . 8]
.XXXX .0005 [ .0 13] ANGULAR: 1 SDP-747D, PRESS W /M OULD
PART
30 10 2PR OPRIETAR Y AND CON FIDENTIAL
OM E RS E T I N D U S T RI E S . IT M AY NOT
INTTEER PR ETT DRAW IING PEER:
N/A
NA M E D AT E
T HE INF O R M A TI O N C O N TA IN E D IN THIS
D RA W I N G AND ASS O CI A TE D CADDATA
FILE S IST HE SOL E P ROP E R T Y OF ANSSII Y 14. 5M -- 198 2
M ATTEERII ALL
DRAW N
CHECKED
K S A VII TT SKI Y 0 2 /12 /08
W LUNT 02 /12 /08 SI ZE DWG.. NO..
REV
S
BE RE P R O D U C E D IN PA R T, OR AS A
W H O L E , OR SE N T T O ANY O T HE R VENDOR,
FI NIISSH
N/A ENG APPR. W LUNT 02 /12 /0 8 D 0747D-PART A
W I T H O U T T HE E X P RE S S WRITTE N
C O N S E NT OF S OM E R SE T INDUST RIES.
M FG APPR.. W LU NT 0 2 / 12//08 SCALE: 1:2.25 N/ A SHEE T 1 OF 2
8 7 6 5 4 3 2
DATABA SE:SOLIDW ORKS Q.A. SCALE: 1
: 2 . 25
WEI GHT
1
SHEE T 1 OF 2

F
F
E
E
D
D
C
C
B
B
A
A
A
8
7
6
5
4
2
3
1
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 0747-121 ASSY, REINFORCEMENT 1
2 3000-201 WASHER, FLAT 3/8 16
3 3000-103 WASHER, LOCK SPLIT 3/8 14
4 3000-409 SCREW, 3/8-16X1 HEXHD SS 10
5 0747-039 BRACKET, FRAME TO SHELL LEFT 6
6 0747-043 BRACKET, FRAME TO SHELL RIGHT 4
7 3000-200 WASHER, FLAT 1/4 20
8 3000-106 WASHER, LOCK SPLIT 1/4 30
9 3000-404 SCREW, 1/4-20 X 3/4 HEXHD 24
10 3000-421 SCREW, 3/8-16 X 1-1/2 HEXHD 5
11 3000-102 WASHER, LOCK SPLIT 5/16 11
12 3000-413 SCREW, 5/16-18 X 1 1/2 HEXHD GR8 7
13 0747-102 BAR, FRONT 1
14 3000-105 WASHER, LOCK SPLIT 1/2 2
15 3000-437 SCREW, 1/2-13 X 1-1/2 HEXHD 2
16 0100-034 FOOT, 1.0 TALL X 1.125 DIA 4
17 4000-300 LEG TIP RUBBER 4
18 4000-122 PLUG, PLASTIC 2.5 DIA 747 FRAME 1
19 5000-611 DECAL, SDP 747 MAIN 1
20 0747-020 PANEL, COVER TOP 1
21 0747-048 PANEL, COVER BOTTOM 1
22 3000-305 NUT, FLANGE 5/16-18 10
23 3000-426 SCREW, 5/16-18 X 1-1/4 SHCS 3
24 0747-167 DOVETAIL, SPACER 1
25 0747-129 BUSHING, PLATEN LEVELING 3
26 0750-199 COVER, 18" PLATEN TOP 1
27 0747-218 INSULATION, COVER CUT TO SIZE 1
28 0747-103 POST, LOWER PLATEN 1
29 4000-312 WASHER, IGUS 1-3/4" ID 1
30 3000-432 SCREW, 1/4-20 X 1-1/2 SHCS 4
31 4000-554 BUSHING, W/SHDR GARLOCK HANDLE 2
32 4000-314 RING, RETAINING EXTERNAL 6
33 3000-205 WASHER, HANDLE PRESS 2 OD 1-1/16ID .047THK 4
34 0747-204 CAM SHAFT 1
35 0747-026 DISK, COVER CYLINDER 1
36 3000-101 WASHER, LOCK INT TOOTH #10 9
37 3000-402 SCREW, 10-32 X 3/8 TRUSS PH SS 11
38 0747-500 ELBOW, HANDLE RIGHT 1
39 0747-128 HANDLE, MAIN 747 1
40 0747-141 BLOCK, MTG C'BAL RIGHT 1
41 0747-144 BLOCK, C'BAL LEFT 1
42 0747-156 STUD, CENTER PLATEN SUPPORT 1
43 0747-124 STUD, BOTTOM PLATEN REST 4
44 4000-257 SPRING, COMPRESSION 747 PLATEN LEVEL 5
45 0747-197 COLLAR, CYLINDER UHMW 747 1
46 0747-109 COLLAR, CYLINDER 747 ALUM 1
47 3000-340 SCREW, 10-32 X 1/4 SET HEX 3
48 3000-303 NUT, FLANGE 1/4-20 5
49 3000-310 NUT, HEX 6-32 6
50 5000-279 BUSHING, CORD LOCK 1
51 5000-280 BUSHING, CORD 747 .565 HOLE 2
52 5000-401 CONTROLLER, TEMP CAL-3200 1
53 5000-200 SWITCH, ROCKER 110/220VAC 3 PRONG SPST 1
54 5000-196 COVER,SWITCH ROCKER 1
55 5000-152 RELAY,CRYDOM D2450G 1
56 5000-153 COVER, RELAY 1
57 5000-267 CLAMP, 5/16ID X 1/2 WIDE X .166DIA NYLON 4
58 0747-117 BRACKET, HEAT SINK 1
59 0747-044 WELDMENT,HORSESHOE 1
60 3000-428 SCREW, 1/4-20 X 3/4 HEX BUTTON HEAD 4
61 3000-410 SCREW, 1/4-20 X 1/2 HEXHD 2
62 3000-420 SCREW, 3/8-16 X 3/4 PAN HD SLOT 1
63 4000-405 KNOB, 2" DIA 3/8-16 1
64 0747-030 BRACKET, KNOB SUPPORT 1
65 5000-323 DECAL "DOUGH PRESS" 1
66 5000-326 DECAL, ETL, MODEL/SERIAL 1
67 5000-317 LABEL, NSF 1
68 0747-104 ROD, LWR PLATEN SPRT 2
69 0747-111 ROD, FRONT FRAME MTG 1
70 4000-558 BEARING, NEEDLE PLATEN SWING 1.75IDX2.125ODX1LG 2
71 4000-557 CAM FOLLOWER, 1 DIA 2
72 0747-602 BLOCK, REAR LEG MTG 2
73 0747-217 CYLINDER WELDMENT MOULD 1
74 0747-604 ASSY, PLATEN UPR W/ SWITCH & T/C 120VAC 1
75 0747-146 COUNTERBALANCE #251, 1.044dia 1
76 0747-609 PLATEN, LOWER MACHINED 1
77 0747-010 FRAME, MAIN 747 1
78 0747-160 ASSY, DOVETAIL GEN III 1
79 0747-601 ASSY, HANDLE SHAFT, CAMS 1
80 3000-339 SCREW, 10-24 X 3/4 ROUND PH 2
81 0747-210 BRACKET, CB NO HOLE 1
82 0747-042 BRACKET PLATEN, MOULD 2OF2 1
83 0747-035 BRACKET PLATEN, MOULD 1OF2 1
84 0747-499 ELBOW, HANDLE LEFT 1
85 5000-241 CABLE 17" 1897C ALPHA W/2 FORK 1
130 3000-231 WASHER, LOCK SPLIT 1/4 GR8 12
A
R EV DES CR I P T I O N CHG'D APP'D D AT E
SOMERSET SOMERSET INDUSTRIES, INC.
DO NOT SC ALE DRAW ING
U NLESS O T HE R W I SE SP E C I F I ED :
DI M E N SI O N S A RE I N I NCHES [M IL LIM E T E R ]
T I TL E ::
NORTH BILLERICA, MA 01862
.XX .015 [ . 4 ]
.XXX .00 5 [ .13 ] FR ACT I O NAL 1/32 [ . 8]
.XXXX .00 05 [ .0 13] ANGULAR: 1
PR OPRI ET AR Y A ND CONFI DENT IA L II NTTEERPR ETT DR AW IING P EER:
NA M E D
AT E
SDP-747D, PRESS W / MOULD
PART
THE INF O R M A TI O N C O N TA I N E D IN T HIS
DRA WI N G AND A S S O CI A T E D CAD D A TA
FIL ES IST HE SOL E P ROP E R T Y OF
ANSSII Y 14.5M -- 1982
M ATTEERII ALL
N/A
DR AWN
CHECKED
K S A VII TT SKI Y 0 2 /12 /0 8
W LUNT 02 / 12 /08 SI ZE DWG.. NO.. REV
S OM E R S E T I N D U S T RI E S . IT M AY NOT BE
RE P R O D U CE D IN P A R T, OR AS A WHOL E,
OR SE N T T O ANY O T HE R VENDOR,
W I T H O U T T HE E X P RE S S WRITTEN
C O N S E NT OF S OM E R SE T INDUST RIES.
FI NIISSH
N/A
ENG APPR..
M FG APPR..
W LU NT 02 / 12 /0 8
W LUNT 0 2 /12 /0 8 D 0747D-PART A
DATABASE:SOLIDWORKS
Q. A . SCALE: 1::1 WEI GHT N/ A SHEE T 2 OF 2
D 0747D- PART
REV
A