Sonoff DIY iFan04 User manual

Wi-Fi Smart Ceiling Fan with Light Controller
User manual V1.0
iFan04
中 文 ----------1-6 English----------7-13 FCC Warning----------14

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
产品介绍
配对按钮/灯开关
433MHz RF天线 Wi-Fi天线
设备重量＜1kg，建议安装⾼度＜2⽶。
产品特点
433MHz遥控控制
远程控制 智能定时/延时 语⾳控制 分享功能
局域⽹控制
同步状态
智能场景 创建群组
本设备为⼀款⻛扇灯控制器，⻛扇灯通过与本设备相连可在易微联App端分别控制灯、⻛扇的开关，⻛速控制、
设󶷈󲷡时开/关和󱲴󱜇给您的󲸛󱜣⼀󸤐󳰝制等等。
风速控制
1
使⽤说明
1.断电
ON O FF
ON O FF
ON O FF
ON O FF
设备安装、故障维修请由专业资质电⼯操作。切勿在设备通电时进⾏接线操作，以免发⽣触电危险！

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
2.接线
NL
LIGHT
FAN
CO M
100-240V AC
L端输⼊前需接保护装置（如：保险丝或空⽓开关）
确保线接⼊⽆误。
2
3.下载“易微联”App
易 微 联
eWeLink
Android™ & iOS

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
󸶱电󱿿，设备⾸次使⽤，默认进󱮦快󸶿配⽹模式。设备蜂鸣器呈两短⼀⻓响声。
三分钟内没有进⾏配⽹，设备将退出快速模式。如需再次进⼊，⻓按设备配对按钮5秒或将设备连续
上电3次（开-关-开-关-开）直到设备蜂鸣器呈两短⼀⻓响声即可。
4.上电
5.添加设备
点击“+”，选择“ 快速添加”，再根据App提⽰进⾏操作。
如使⽤快速添加模式配⽹失败，请使⽤“兼容配⽹模式”进⾏配对。
兼容配⽹模式
1⻓按设备配对按钮5秒直到设备蜂鸣器呈󾖶两短⼀⻓󾖶响声，松开。再次⻓按配对按钮5秒直到设备
蜂鸣呈󾖶快响󾖶状态(滴滴滴滴..........)，此时设备进⼊兼容配⽹模式。
2在App界⾯，点击“+”，选择“兼容模式”。
输⼊Wi-Fi󲸹码，点击“下⼀步”再点击“去连接”，将移动设备连接上Wi-Fi账号为：ITEAD-**********，
密码为：12345678，然后回到“易微联”App，点击“下⼀步”，等待配对完成。
设备连续上电5次（开-关-开-关-开-关-开-关-开）也可进⼊“兼容配⽹模式”
3
取出遥控器绝缘⽚
出⼚时，RM433R2遥控器已与iFan04进⾏绑定，取出遥控器电池绝缘⽚之后即可进⾏控制，如不能控制，
请尝试重新学习。

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
设备与RM433R2遥控器的学习⽅法：
在设备上电后的5秒内⻓按遥控器任意按键⾄设备蜂鸣器“滴”⼀声，即全部按键学习成功，如5秒内未进⾏
下⼀步操作，请重新上电。
设备最多配对10遥控器，超过10个则会⾃动覆盖第⼀个学习的遥控器，以此类推。
<RM433R2
产品参数
型号
输󱲠
iFan04-L, iFan04-H
PC V0
-10℃~40℃
灯具:100-240VAC50/60Hz3AMax
钨丝灯:360W/120VMaxLED:150W/120VMax
⻛扇:100-240VAC50/60Hz2AMax
116x55x26mm
输⼊ 100-240V AC 50/60Hz 5A
iFan04-L：
灯具:100-240VAC50/60Hz3AMax
钨丝灯:690W/230VMaxLED:300W/230VMax
⻛扇:100-240VAC50/60Hz2AMax
iFan04-H：
RF 433MHz
Wi-Fi IEEE 802.11 b/g/n 2.4GHz
App⽀持系统 Android & iOS
外壳材料
产品规格
⼯作温度
4

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
更换设备⽹络
在eWeLinkApp设备设置界⾯选择“WiFi设󶷈”进⾏更换。
设备设 置
创建群组
WiFi设置
设备ID
MAC地址
删除设备
1000 a3517 f
60:0 1:94: AC:CC:F D
固件名称 PSF-BF B-GL
⻓按设备“ 配对按钮”5秒直到设备蜂鸣器呈两短⼀⻓响声，松开，此时设备进⼊快速配⽹模式，即可再󴤣
通过eWeLinkApp进⾏添加。
⽅法3：
将设备连续上电3次（开-关-开-关-开）,直到设备蜂鸣器呈两短⼀⻓响声，松开，此时设备进⼊快速配⽹模式，
即可再󴤣通过eWeLinkApp进⾏添加。
恢复出⼚设置
在eWeLinkApp端“删除设备”，设备即恢复出⼚设置。
iF an04
定时 延时⻛扇开关
低中⾼
灯开关
设备信息
通电反应关闭
设备设置
⼩程序控制
局域⽹控制
WiFi设置
5
重新配对
⽅法1：
⽅法2：
⻓按RM433R2遥控器配对按钮5秒直到设备蜂鸣器呈两短⼀⻓响声，松开，此时设备进⼊快速配⽹模式，
即可再󴤣通过eWeLinkApp进⾏添加。
配⽹模式下，短按遥控器任意按键可退出当前模式。

中⽂
Shenzhen Sonoff Technologies Co., Ltd.
遥控器参数
RM433R2
433MHz
87x45x12mm
86x86x15mm(可选)
PCV0
型号
RF
遥控器尺⼨
遥控器底座尺⼨
供电
外壳材料
3V纽扣电池x1（电池型号:CR2450）
灯开/关按键 静⾳按键
三档⻛速
关闭⻛扇
RF清码按键（⻓按5s） Wi-Fi配对按键（⻓按5s）
⼆档⻛速
⼀档⻛速
iFan04⽀持使⽤RM433R2遥控器进⾏控制，学习成功后，即可根据下图按键说明控制设备，此功能属于本地
近程⽆线遥控与Wi-Fi⽹络⽆关。
RF清码⽅法：⻓按RF清码按键5秒⾄设备蜂鸣器发出“滴滴”两声，即完成清码。
Wi-Fi设备与eWeLinkAPP配对失败。
1.确保设备处于配对模式。三分钟内没进⾏配⽹，设备将⾃动退出配对模式。
2.请开启定位服务并允许定位权限。在选择Wi-Fi󶶘络之前，请开启定位服务并允许定位权限。位置信息
权限⽤于获取Wi-Fi列󸀭󱣬󳚢。󾖴󲤕果单击禁⽤，您将⽆法添加设备。
3.确保您的Wi-Fi󶶘络为2.4GHz频段。
4.确保您输⼊了正确的Wi-FiSSID和󲸹码，没有包含特殊字符。密码错误是配对失败的⼀个⾮常常⻅的
原因。
5.配对时设备应靠近路由器，以保证良好的传输信号条件。
常⻅问题
遥控器介绍
6
出⼚默认设备的蜂鸣器会在开/关⻛扇、调节⻛扇档位、设备处于配对模式时发出声⾳作为操作提⽰，在开
关灯时不会响。如果需要关闭蜂鸣器声⾳，请通过配对的433󸹴󳰝󲏜短按“静⾳”按键关闭。

Shenzhen Sonoff Technologies Co., Ltd. English
This is a Wi-Fi smart controller for the ceiling fan with light that allows you to remotely turn on/off the
fan and light separately, adjust the fan speed, schedule it on/off and share it with your families to
control together, etc. on the eWeLink App.
Fan Speed Adjustment
7
ON O FF
ON O FF
ON O FF
ON O FF
433MHz RF antenna
Wi-Fi antenna
Pairing button/On/Off (light)
The device weight is less than 1 kg. The installation height of less than 2 m is recommended.
Features
Remote Control Single/Countdown
Timing
Share Control Voice Control
Smart Scene Sync Status LAN Control 433MHz Remote
Control
Please install and maintain the device by a professional electrician. To avoid electric shock
hazard, do not operate any connection while the device is powered on !
1. Power off
Product Introduction
Operating Instruction
Group Control

Shenzhen Sonoff Technologies Co., Ltd. English
NL
LIGHT
FAN
CO M
100-240V AC
2. Wiring instruction
Make sure all wires are connected correctly.
eWeLink
eWeLink
Android™ & iOS
3. Download the eWeLink APP
Please install protection devices before connecting the live wire. (e.g. fuses or air switches).
8

English
9
Shenzhen Sonoff Technologies Co., Ltd.
1Press and hold the pairing button for 5s until the buzzer makes two short beeps and one
long beep then release. Press the pairing button for 5s again until the buzzer makes a high
frequency of beeps, which means the device has entered "compatible pairing mode".
2
Keep turning the device on and off repeatedly for 5 times (on-off-on-off-on-off-on-off-on) to
enter "compatible pairing mode".
5. Add the device
4.Power on
After powering on, the device will enter the quick pairing mode during the first use, then the
device makes two short beeps and one long beep.
Tap “+” and select “Quick Pairing”, then operate following the prompt on the App.
Compatible Pairing Mode
If you fail to enter Quick Pairing Mode, please try “Compatible Pairing Mode ” to pair.
Tap “+” and select “ Compatible Pairing Mode ” on App.
Select Wi-Fi SSID with ITEAD-****** and enter the password 12345678, and then go back to
eWeLink App and tap “Next”. Be patient until pairing completes.
The device will exit the quick pairing mode if not be paired within 3mins. If you want to enter
the quick pairing mode again, press and hold the pairing button for 5s, or keep turning the
device on and off repeatedly for 3 times (on-off-on-off-on) until the buzzer makes two short
beeps and one long beep.

10
English
Shenzhen Sonoff Technologies Co., Ltd.
Remove the Battery Insulation Sheet
After factory setting, RM433R2 remote controller is bound to iFan04 by default. Simply remove
the battery insulation sheet to use. If the device connected to iFan04 is not controlled by the
remote controller, try to learn the remote controller again.
This device can learn up to 10 remote controllers. The 11th remote controller will automatically
cover the first learned one, and so on.
<RM433R2
Learning Method for iFan04 and RM433R2 Remote Controller
After powering on iFan04, press any button on the controller until the buzzer makes a "beep"
sound within 5s, then all the buttons are learned successfully. If you do not operate any step
within 5s, power the device on again and repeat the above operation.

English
11
Shenzhen Sonoff Technologies Co., Ltd.
Specifications
iFan04-L, iFan04-H
PC V0
-10℃~40℃
116x55x26mm
100-240V AC 50/60Hz 5A
Light:100-240V AC 50/60Hz 3AMax
Tungsten lamp:360W/120V Max LED: 150W/120V Max
Fan:100-240V AC 50/60Hz 2A Max
iFan04-L：
Light:100-240V AC 50/60Hz 3AMax
Tungsten lamp:690W/230VMax LED: 300W/230VMax
Fan:100-240V AC 50/60Hz 2AMax
iFan04-H：
RF 433MHz
Wi-Fi IEEE 802.11 b/g/n 2.4GHz
Android & iOS
Model
Input
Output
Dimension
App operating systems
Working temperature
Material
iF an04
Fan
Low Med ium High
Ligh t
Sched ule Timer
Dev iceSetti ngs
Cre ategroup
WiFiSettings
Dev iceID
MACaddress
1000 a3517 f
60:0 1:94: AC:CC:F D
FWName PSF-B FB-GL
Dev iceinfo
Powe r-onState
WeC hatco ntrol
LANc ontr ol
Dev iceSe ttin gs
Del etedev ice
WiFiSettings
Select the "Wi-Fi Settings" in the "Device Settings" interface on the eWeLink App to change.
Switch Network

English
12
Shenzhen Sonoff Technologies Co., Ltd.
Method 3:
Keep turning the device on and off repeatedly for 3 times (on-off-on-off-on) until the buzzer
makes two short beeps and one long beep then release, which means the device has entered
quick pairing mode, so it can be added in the eWeLink App again.
Method 2:
Press the "pairing button" on RM433R2 remote controller for 5s until the buzzer makes two
short beeps and one long beep then release, which means the device has entered quick pairing
mode, so it can be added in the eWeLink App again.
In quick pairing mode, press any button on the remote controller to exit the current mode.
Factory Reset
Deleting the device on the eWeLink APP indicates you restore it to factory setting.
Method 1:
Press the "pairing button" on the device for 5s until the buzzer makes two short beeps and one
long beep then release, which means the device has entered quick pairing mode, so it can be
added in the eWeLink App again.
Re-establish Pairing

English
Model
RF
Remote controller size
Remote controller base size
Power supply
Material
RM433R2
433MHz
87x45x12mm
PC V0
3V button cell x 1 (Battery model: CR2450)
86x86x15mm (not included)
Mute
Medium speed
Low speed
On/Off (light)
High speed
Off (fan)
13
Shenzhen Sonoff Technologies Co., Ltd.
Remote Controller Introduction
RF Clearing Button (Long Press for 5s) Wi-Fi Pairing Button (Long Press for 5s)
The buzzer of iFan04 in factory default setting will indicate you with the "beep" sound when you
turn on/off the fan, adjust the fan speed, and the device enters pairing mode, but no a "beep"
sound is made when you turn on/off the light. You can press the "Mute" button on the paired
RM433R2 remote controller to silence the buzzer.
Remote Controller Specifications
iFan04 can be controlled by RM433R2 remote controller. After learning is successful, you can
control the device connected with iFan04 according to the button instruction below. This
feature is referred to as a short-distance wireless communication, unrelated to Wi-Fi network
communication.
RF Clearing Method:
Press and hold the RF clearing button for 5s the buzzer makes "beep, beep" sound after clearing
is successful.
Common Problems
Fail to pair Wi-Fi devices to eWeLink APP
1. Make sure the device is in pairing mode. After three minutes of unsuccessful pairing, the
device will automatically exit pairing mode.
2. Please turn on location services and allow location permission. Before choosing the Wi-Fi
network, location services should be turned on and location permission should be allowed.
Location information permission is used to obtain Wi-Fi list information. If you click Disable,
you will not be able to add devices.
3. Make sure your Wi-Fi network runs on the 2.4GHz band.
4. Make sure you entered a correct Wi-Fi SSID and password, no special characters contained.
Wrong password is a very common reason for pairing failure.
5. The device shall get close to the router for a good transmission signal condition while pairing.

FCC Radiation Exposure Statement:
FCC Warning
Changes or modifications not expressly approved by the party responsible for compliance
could avoid the user’s authority to operate the equipment.
Note:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance20cm
between the radiator & your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
FCC Warning
14
Shenzhen Sonoff Technologies Co., Ltd.

Shenzhen Sonoff Technologies Co., Ltd.
MADE IN CHINA
1001, BLDG8, Lianhua Industrial Park, shenzhen, GD, China
ZIP code: 518000 Website: sonoff.tech
https://sonoff.tech/usermanuals
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type
iFan04-L, iFan04-H is in compliance with Directive 2014/53/EU.The full text of the EU declaration
of conformity is available at the following internet address: