Sony CDX-CA540X User manual

1
Ver 1.0 2002. 12
Model Name Using Similar Mechanism NEW
CD Drive Mechanism Type MG-393XC-121//K
Optical Pick-up Name KSS-721A
SERVICE MANUAL
E Model
CDX-CA540X/CA590X
FM/AM COMPACT DISC PLAYER
CD player section
Signal-to-noise ratio 90 dB
Frequency response 10 – 20,000 Hz
Wow and flutter Below measurable limit
Tuner section
FM
Tuning range FM tuning interval:
50 kHz/200 kHz switchable
87.5 – 108 MHz
(at 50 kHz step)
87.5 – 107.9 MHz
(at 200 kHz step)
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz
Usable sensitivity 11 dBf
Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 65 dB (stereo),
68 dB (mono)
Harmonic distortion at 1 kHz
0.7% (stereo),
0.5% (mono)
Separation 33 dB at 1 kHz
Frequency response 30 – 15,000 Hz
AM
Tuning range AM tuning interval:
9 kHz/10 kHz switchable
531 – 1,602 kHz
(at 9 kHz step)
530 – 1,710 kHz
(at 10 kHz step)
Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity AM: 30 µV
SPECIFICATIONS
Power amplifier section
Outputs Speaker outputs
(sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output 50 W ×4 (at 4 ohms)
General
Outputs Audio outputs (rear)
Power antenna relay control terminal
Power amplifier control terminal
Inputs BUS control input terminal
BUS audio input terminal
Remote controller input terminal
Antenna input terminal
Tone controls Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements 12 V DC car battery
(negative earth)
Dimensions Approx. 178 ×50 ×180 mm
(w/h/d)
Mounting dimensions Approx. 182 ×53 ×161 mm
(w/h/d)
Mass Approx. 1.2 kg
Supplied accessories Parts for installation and connections (1set)
Front panel case (1)
Card remote commander
RM-X115 (CDX-CA590X)
Note
This unit cannot be connected to a digital preamplifier or an equalizer
which is Sony Bus system compatible.
Design and specifications are subject to change without
notice.
Sony Corporation
e Vehicle Company
Published by Sony Engineering Corporation
9-874-262-01
2002L0400-1
© 2002. 12
Photo: CDX-CA540X
• The tuner and CD sections have no adjustments.

2
CDX-CA540X/CA590X
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
Notes on CD-R/CD-RW discs
•You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
These marks denote that a disc is not for audio use.
•Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
•You cannot play a CD-R/CD-RW that is not finalized∗.
∗A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
This label is located on the bottom of the chassis.
This label is located on the drive unit’s internal chassis.
When replacing the chassis (T) of mechanism deck which have the
“CAUTION LABEL” attached, please be sure to put a new
LABEL (OP CAUTION) (3-223-913-01) to the chassis (T).

3
TABLE OF CONTENTS
1. GENERAL
Location of controls................................................................. 4
Connections ............................................................................. 4
2. DISASSEMBLY
2-1. Sub PanelAssy (CD)........................................................... 6
2-2. CD Mechanism Block ......................................................... 7
2-3. Main Board ......................................................................... 7
2-4. Heat Sink ............................................................................. 8
2-5. Chassis (T) Sub Assy .......................................................... 8
2-6. Lever Section, In Self Sw Board ......................................... 9
2-7. Servo Board ......................................................................... 9
2-8. Shaft Roller Assy, Load Sw Board.................................... 10
2-9. Floating Block Assy .......................................................... 10
2-10. Optical Pick-up Block .......................................................11
MAIN BOARD CNP701
SERVO BOARD CN1
3. DIAGRAMS
3-1. IC Pin Description............................................................. 12
3-2. Circuit Boards Location .................................................... 14
3-3. Block Diagram –CD Section–........................................... 15
3-4. Block Diagram –Tuner Section–....................................... 16
3-5. Block Diagram –Display Section–.................................... 17
3-6. Printed Wiring Boards –CD Mechanism Section–............ 18
3-7. Schematic Diagram –CD Mechanism Section– ................ 20
3-8. Printed Wiring Boards –Main Section– ............................ 21
3-9. Schematic Diagram –Main Section (1/2)– ........................ 22
3-10. Schematic Diagram –Main Section (2/2)– ........................ 23
3-11. Printed Wiring Board –Relay Section– ............................. 24
3-12. Printed Wiring Board –Display Section– ..........................25
3-13. Schematic Diagram –Display Section–............................. 26
3-14. IC Block Diagrams............................................................ 27
4. EXPLODED VIEWS
4-1. Chassis Section ................................................................. 30
4-2. Front panel Section ........................................................... 31
4-3. CD Mechanism Section (1) ............................................... 32
4-4. CD Mechanism Section (2) ............................................... 33
4-5. CD Mechanism Section (3) ............................................... 34
5. ELECTRICAL PARTS LIST ........................................ 35
CDX-CA540X/CA590X
EXTENSION CABLE AND SERVICE POSITION
Whenrepairing or servicing this set, connect thejig(extensioncable)
as shown below.
•Connect the MAIN board (CNP701) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-062-1).

4
CDX-CA540X/CA590X SECTION 1
GENERAL This section is extracted
from instruction manual.
Connections

5
CDX-CA540X/CA590X

6
CDX-CA540X/CA590X SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY (CD)
2-1. SUB PANEL ASSY (CD)
(Page 6)
2-2. CD MECHANISM BLOCK
(Page 7)
2-5. CHASSIS (T) SUB ASSY
(Page 8)
2-6. LEVER SECTION
IN SELF SW BOARD
(Page 9)
2-8. SHAFT ROLLER ASSY
LOAD SW BOARD
(Page 10)
2-9. FLOATING BLOCK ASSY
(Page 10)
2-10. OPTICAL PICK-UP BLOCK
(Page 11)
SET
2-7. SERVO BOARD
(Page 9)
2-3. MAIN BOARD
(Page 7)
2-4. HEAT SINK
(Page 8)
4 CNP803
5 sub panel assy (CD)
3 claws
2 claws
1 PTT 2.6x6

7
CDX-CA540X/CA590X
3 screw (+BTT)
4 screws (+BTT)
1 PTT 2.6x8
5 MAIN board
2 PTT 2.6x
8
1 PTT 2.6x6
6 PTT 2.6x
6
7 bracket (CD)
2 PTT 2.6x6
5 CD mechanism block
4 CNP701
3
2-2. CD MECHANISM BLOCK
2-3. MAIN BOARD

8
CDX-CA540X/CA590X
2-5. CHASSIS (T) SUB ASSY
2-4. HEAT SINK
7 heat sink
1 PTT 2.6x8
2 PTT 2.6x8
4 PTT 2.6x8
3 PTT 2.6x12
6 PTT 2.6x8
5 PTT 2.6x
8
4 chassis (T) sub assy
3 P 2x3
2 P 2x3
1 Unsolder the
lead wires.
black
red
white

9
CDX-CA540X/CA590X
2-6. LEVER SECTION, IN SELF SW BOARD
2-7. SERVO BOARD
4 claws
2 IN SELF SW board
7 lever (L)
3 tension spring (LR)
6 lever (R)
5 guide (disc)
1 special screw
6 special screws
1 CN3
2 Removal the solders.
4 P 2x3
5 loading motor assy
8 SERVO board
7 special screw
9 FLEXIBLE board
optical pick-up block
3 Unsolder the
lead wires.
black
yellow

10
CDX-CA540X/CA590X
1 tension spring (KF1)
7 compression spring (FL)
6 floating block assy
8 compression spring (FL)
4 Fit lever (D) in the
direction of the arrow.
2 damper (T)
3 damper (T)
5 Turn loading ring in the
direction of the arrow.
2-9. FLOATING BLOCK ASSY
2-8. SHAFT ROLLER ASSY, LOAD SW BOARD
• When installing, take note of the positions
arm (roller) and washers. (Fig. 1)
Fig. 1
1 tension spring (RA)
2 arm (roller)
3 retaining ring (RA)
4 shaft retainer (roller)
5 shaft roller assy
6 special screw
7 LOAD SW board
retaining ring
(RA) arm arm
washer washer shaft retainer
(roller)
shaft retainer (roller)

11
CDX-CA540X/CA590X
1 P 2x3
4 screw
5 plate spring (feed)
6 shaft (feed) assy
2 sled motor assy
3 optical pick-up block
2-10. OPTICAL PICK-UP BLOCK

12
CDX-CA540X/CA590X
3-1. IC PIN DESCRIPTION
• IC801 µPD780076YGK-R24 (SYSTEM CONTROL) (MAIN Board)
Pin No. Pin Name I/O Pin Description
1DSW I Down switch detection signal input “L”: Down switch on
2LM LD O Loading motor drive control signal output (Loading direction)
3LM EJ O Loading motor drive control signal output (Eject direction)
4ATT O Mute control signal output of audio signal line “H”: mute on
5AATTOMute control signal output to power amp IC (IC101) “L”: amp mute on
6 PLL DI I Serial data signal input to PLL IC (IC601)
7VOL ATT O Mute control signal output to Electric volume IC (IC401)
8DOOR SW/IND I Door switch signal input Case of flipdown, sense to open condition of door “H”: open
9VSS0 —Ground pin
10 VDD0 —Power supply pin
11 PLL CE O Chip enable signal output to PLL IC (IC601)
12 BEEP O Beep signal output of key beep, caution alarm to power amp IC (IC101)
13 SDAO O IIC data line signal output (control to electric volume IC (IC401))
14 SCLO O IIC clock line signal output (control to electric volume IC (IC401))
15 LCD CE O Chip enable control signal output to LCD driver IC (IC901)
16 LCD DO O Serial data signal output to LCD driver IC (IC901)
17 LCD CLK O Serial clock signal output to LCD driver IC (IC901)
18 BUS SI I SONY bus data signal input from bus interface IC (IC802)
19 BUS SO O SONY bus data signal output to bus interface IC (IC802)
20 BUS CLK I SONY bus clock signal input
21 BUS CLK GEN O SONY bus clock signal output
22 AM ON O AM select signal output
FM circuit power supply control output of tuner unit (TU601) “H”: FM on
23 FM ON O FM select signal output
FM circuit power supply control output of tuner unit (TU601) “H”: FM on
24 VDD1 —Power supply pin
25 AVSS —Ground pin
Stereo signal input/monaural control signal output
26 ST IND I/O At forced monaural on: “L”output
At forced monaural off: input mode, stereo on for “L”input
27 SHIFT/PH1 I Rotary commander shift key signal input
28 S METER I S meter signal input from tuner unit (TU601)
29, 30 KEY0, KEY1 I A/D key signal input Input ofA/D key matrix and front panel attachment decision.
31 R COM I Rotary commander AD level signal input
Sense to key voltage level of rotary commander
32 DST SEL I Destination select input from frequency select switch (SW803)
33 TEST I Test mode select signal input “L”: test mode
34 AVREF —Analog reference voltage pin
35 AD ON O LCD INHIBIT signal output
36 RESET I Reset signal input from reset IC (IC902) “H”: reset
37 XT2 —Connect to sub clock (32.768 kHz)
38 XT1 —Connect to sub clock (32.768 kHz)
39 IC —At on board writer: 12 V power supply pin (usually ground pin)
40 X2 —Connect to crystal oscillator (8.38 MHz)
41 X1 —Connect to crystal oscillator (8.38 MHz)
42 VSS1 —Ground pin
43 KEYACK I Key acknowledge signal input
44 SIRCS I Wireless remote control signal input from remote control receiver IC (IC951)
45 SELF SW I SELF switch detection signal input “L”: SELF switch on
46 BU IN I Backup power supply detection signal input
47 NOSE I Front panel attachment detection signal input from SW801 “L”: panel on
SECTION 3
DIAGRAMS

13
CDX-CA540X/CA590X
Pin No. Pin Name I/O Pin Description
48 ILL ON O Front panel illumination power supply control signal output “H”: illumination on
49 A REMO O External amplifier remote control signal output
50 CDM ON O CD mechanism deck power supply control signal output “H”: CD power on
51 XCD ON O CD DSP power supply control signal output “H”: CD power on
52 ACC IN I Accessory power supply detection signal input “L”: accessory on
53 BUS ON O SONY bus on signal output to bus interface IC (IC802)
54 BUS RST O SONY bus reset signal output to bus interface IC (IC802)
55 PW ON O System power supply control signal output
56 X SO PLL SO O CD and PLL serial data signal output
57 X SI I CD serial data signal input
58 X SCK PLL SCK O CD and PLL serial data signal output
59 RF OK I CD RF OK signal input
60 CD RST O CD reset control signal output
61 IN SW/PH2 I DISC IN switch detection signal input “L”: DISC IN switch on
62 X AO O Parameter/command select signal output
63 STB O CD strobe signal output
64 L SW I LIMIT switch detection signal input “L”: LIMIT switch on

14
CDX-CA540X/CA590X
3-2. CIRCUIT BOARDS LOCATION
MAIN board
tuner unit
(TU601)
DISPLAY board
SERVO board
IN SELF SW board SPEAKER board
SL SW board
RELAY board
LOAD SW board

15 15
CDX-CA540X/CA590X
84
85
82
83
16
12
D/A
CONV
TRACKING
ERROR
FORCUS
ERROR
9
1
OSC
EFM
DEMOD
SERVO
CTL
RF
EQ
52
56
54
55
DSUB CODE
PROCESS
8
7
6
5
4
3
2
1
45
61
64
50
51
56
57
58
63
62
60
59
I/F
87
86
97
98
LD
DRIVE
Q1
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
SLED
MOTOR
DRIVE
SPINDLE
MOTOR
DRIVE
LOADING
MOTOR
DRIVE
6
5
23
2
15
16
17
18
13
14
11
12
9
10
26
62 63 64 65
3
2
36
CD MECHANISM
ON SWITCH
Q905,906
CD ON
SWITCH
Q921
CD
+6V REG
Q907,D908
CD+5V
REG
Q910,D911
M902
(SLED)
M901
(SPINDLE)
M903
(LOADING)
SW3
(DISC IN)
SW2
(SELF)
SW4
(LIMIT)
SW1
(DOWN)
X1
16.9344MHz
OPTICAL PICK-UP
KSS-721A
I-V
CONV.
CDL
STB
X A0
X_SO/PLL_SO
X_SI
X_SCK/PLL_CLK
CD_RST
RFOK
D_SW
IN_SW
SELF_SW
L_SW
LM _LD
LM_ EJ
CDM ON
XCD_ON
R-CH
TUNER
SECTION
A
X EN
PLL DO
PLL CLK TUNER
SECTION
B
23 24
M
M
M
1RESET
SW802
RESET
2
IC902
UCOM+5V
BATT
D909
LOUT
ROUT
PACK
TSTB
TSI
TSCK
SI
RFOK
SO
SCK
STB
AO
XTALEN
RST
RESET
A
C
B
D
E
F
PD
LD
B
D
A
C
E
F
PD
A+5V
LD
APC
FCS-
FCS+
TRK+
TRK-
SL-
SL+
SP+
SP-
LD-
LD+
FOCUS
COIL
TRACKING
COIL
FD
TD
SD
MD
LOAD
EJECT
SYSTEM CONTROL
IC801(1/3)
RF AMP,DIGITAL SERVO
DIGITAL SIGNAL PROCESSOR
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING MOTOR DRIVE
FD TD SD MD
• Signal path
:CD
• R-ch is omitted due to
same as L-ch.
A+5V
AU+5V
D+5V
DR+6V
IC1
IC2
3-3. BLOCK DIAGRAM — CD SECTION —
(Page 16)
(Page 16)

1616
CDX-CA540X/CA590X
CNJ601
(ANTENNA) 2 16
1
FM_ANT L-CH
17
R-CH
CDL
24
DET_OUT
11
FM/AM_OSC
14
AM_VT
6
FM_VT
20
IF_COUNT
19
OSC-IN
21
12
9
S_METER
TU+8V
22
SD/ST_IND
FM_VCC
AM_VCC
AM_ANT
TUNER UNIT
TU601
7
14
13
27
26
25
10
11
6
821
SYSTEM CONTROL
IC801 (2/3)
PLL
IC601
ELECTRONIC VOLUME
IC401
OUTF1
20
19
18
OUTR1
OUTF2 R-CH
OUTR2
12
BEEP
ATT
55
4
PW ON
5
A_ATT
52
ACC IN
C1
B1
D1
D2
SDA
SCL
MUTE
VOL ATT
SCLO
SDAO
6PLL_DI
11 PLL_CE
LCL
S_METER
FM POWER
CONTROL
Q605,606
SD_IND
REAR AUDIO OUT
CD
SECTION
A
CD
SECTION
B
LINE MUTE
CONTROL
Q401,402
LINE MUTE
Q102
LINE MUTE
Q101
R-CH
BATT
BATT
22 MUTE
4STBY
16 AUX-IN
11
12 5
3
9
7
POWER AMP
IC101
1
9
2
10
CNP901
R-CH
PJ401
-1
-2
FL+
FL–
RL+
RL–
4
12
FR+
FR–
3
11
RR+
RR–
16 +B (BATT)
5AMP REM
6
8
17
ANT REM
GND
R-CH
F901
10A
7ACC
15 TEST
33
TEST
A REMO
13
•
25 FM/AM_VCC
26
28
BATT
19
18
L
R
• Signal path
:FM
:AM
:CD
• R-ch is omitted due to
same as L-ch.
AMP
REMOTE CONTROL
Q911,917 ANT
REMOTE CONTROL
Q903,916
COM+8V REG
Q918,919,929,D923
+5 V REG
Q920,D930,D999
BATT
BATT
BATT DET
D854
+5V
BATT
X EN
PLL DO
PLL CLK
D932
D931
TU+8V
TUNER ON
CONTROL
Q909,912
TUNER +8V
REG
Q913,D913
COM+8V
R-CH
8
FM_VCO
15
AM_VCO
16
FM_CP
18
VT
19
AM_CP
20
OSC
2
SEEK XO
XI
10
IFC
13
MONO
11 24
1
CE 3
CK 5
D_IN 4
D_OUT 6
X601
10.25MHz
3
AM_DX/LCL
4
FM_DX/LCL
46
BU IN
18
BUSSI
19
BUSSO
49
AM POWER
CONTROL
Q603,604
23
FM ON
22
AM ON
53
BUSON
54
BS RST
20
BUS CLK
21
10
8
9
12
13
11
BUS CK GEN
BATT CHECK
DATA IN
DATA OUT
BUSON IN
RST OUT
CLK IN
1
6
4
BUSON OUT
DATA IN/OUT
CLK OUT
6
7
8
5
4
3
2
1
BUS ON SIRCS
RST
NC
DATA
CLK
RST OUT
BATT
2
3
ACC
CHECK
Q902
BU CHECK
Q904
D907
BUS INTERFACE
IC802
GND
+B
CNJ801
BUS
CONTROL IN
3-4. BLOCK DIAGRAM — TUNER SECTION —
(Page 15)
(Page 15)

17 17
CDX-CA540X/CA590X
3-5. BLOCK DIAGRAM — DISPLAY SECTION —
X802
32kHz
37
38 40
41
29
30
43
SYSTEM CONTROL
IC801 (3/3)
LCD DRIVER
IC901
KEY 0 DATA
CLK
CE
ILL POWER
CONTROL
Q914
ILL B+
SWITCH
Q915
ILL B+
KEY 1
KEY 1
KEY 0
KEY MATRIX
LSW901-918
S902,903,931
KEY ACK
35 AD ON
27 SHIFT
31 R COM
47 NOSE
XT2
XT1 X2
LCD DO
LCD CLK
LCD CE
48
ILL ON
44
SIRCS
BATT
X1
X801
8.38MHz
LED901-906
LSW901-918
REMOTE CONTROL
RECEIVER
IC951
LCD
BACKLIGHT
64
63
62
16
17
15
COM1
COM4
LCD
LCD901
LED914,915
()
LED930,931
KEY
ILLUMINATION
()
52
|
55
1
|
12
•
15
|
45
SEG1
SEG12
|
|
SEG15
SEG45
|
•
DI
CL
CE
VCC
1
OUT
2
8DOOR SW/IND
AD ON
Q801
RELAY
BOARD
SW801
(NOSE)
CNP802
(REMOTE IN)
LED
POWER CONTROL
Q908,922
DST SEL
SW803
FREQUENCY
SELECT
FM50k
AM9k
FM200k
AM10k
32
— Main Board —
1
2
8.38MHz
IC801 r; (X2)
32.768kHz
IC801 ej (XT2)
5Vp-p
3Vp-p
3
10.25MHz
IC601 1(XO)
2.5Vp-p
• Waveforms
— Servo Board —
(MODE: CD PLAY)
1
2
3
IC1 ts (PACK)
IC1 uj (RFO)
1.2Vp-p
4
Approx. 100mVp-p
IC1 oa (FEO)
0V
5
Approx. 100mVp-p
IC1 od (TEO)
2Vp-p
16.9344MHz
IC1 wd (XTAL)
5Vp-p
0V
3.2msec

1818
CDX-CA540X/CA590X
1
A
B
C
D
E
F
G
H
I
J
234567891011121314
CN2
3-6. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 14 for Circuit Boards Location.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
for schematic diagram:
•All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•%: indicates tolerance.
•f: internal component.
•C: panel designation.
•A: B+ Line.
•Powervoltageis dc 14.4V and fed withregulateddcpower
supply from ACC and BATTcords.
•Voltagesare taken with aVOM(Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
•Circled numbers refer to waveforms.
•Signal path.
F: FM
f: AM
J: CD
for printed wiring boards:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•x: parts mounted on the conductor side.
•a: Through hole.
•: Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side: Parts onthepatternfacesideseenfromthe
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
Note: The components identified by mark 0or dotted line
with mark 0are critical for safety.
Replace only with part number specified.

19 19
CDX-CA540X/CA590X
1
A
B
C
D
E
F
G
H
I
J
234567891011 12 13 14
SW3
SW2
SW4
SW5
TP8
C45
C4
C26
C37
TP6
TP1
TP2
TP4
TP5
TP87
TP86
TP57
TP77
TP11
TP79
TP83
TP70
TP9
TP27
TP12
TP78
TP10
TP81
TP84
TP54
TP25
TP24
TP37
TP39
TP36
TP38
TP40
TP45
TP22
TP88
TP41
TP46
TP21
TP17
TP20
TP42
TP19
TP28
TP90
C41
TP29
C44
TP73 TP32
TP48
TP71
TP51
TP49
TP52
TP55
TP75
TP53
TP56
TP43
TP58
TP61
TP74
TP68
TP80
TP7
TP62
TP91
TP63
C40
TP66
TP64
TP69
TP72
TP50
TP26
TP3
TP59
TP76
TP18
TP89
TP30
R8
R9
R5
R7
R12
R14
R15
R10
R17
R18
R19
R20
R22
FB1
TP92
C3
C5
C6
C8
C9 C10
C11
C13
C14
C16
C18
C19
C24
C25
C29
C34
C36
C38
C35
C21
C22
C30
C23
C1
C27
R21
TP47
C15
C20
TP35
TP23
C17
TP82
TP44
Q1
R26
TP34
R3
TP16
TP85
IC1
IC2
C43
R30
R29
X1
TP60
CN3
CN1
(Page 21)

2020
CDX-CA540X/CA590X
• Refer to page 17 for Waveforms.
3-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 27 for IC Block Diagrams.
(Page 22)
IC B/D
IC B/D
TP77
TP78
R29
R30
C43
TP79
TP80
TP81
TP82
TP83
TP84
CN2
CN3
TP85
M902
M901
SW2 TP4
TP2
TP3
M903
TP87
TP86
TP9 TP8
R3 R26
C4
TP10
C13
R5
C11
C10
C8
TP7
TP92
TP17
TP20
TP16
TP19
TP21
TP18
R7
TP6
C17
FB1
TP11
TP12 C9
C14
TP89
C19
C20 C23
R9
R8
TP22
TP23
TP24
TP25
TP88
C26
TP32
R14
R15
TP30
R12
R10
TP91 C37
TP90
TP29
TP28
TP26
TP27
R21
R22
TP34
TP35
TP36
TP46
TP37
TP38
TP39
TP40
TP41
TP42
TP43
TP44
TP45
CN1
R18
R19
R20
R17
TP66
TP62
TP47
TP63
TP48
TP49
TP64
TP50
TP51
TP52
TP68
TP53
TP69
TP54
TP70
TP55
TP71
TP56
TP72
TP57
TP73
TP58
TP74
TP59
TP75
TP60
TP76
TP61
X1
SW3
SW4
CN13
Q1
C18
IC2
IC1
TP1
TP5
C44
C40
C1 C5 C3 C6
C15
C16
C41
C27
C45
C34
C29
C25
C36
C38
C35
C24
C30
C22
C21
SW5
Note:
•Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : CD PLAY