Sony MVE-8000A-C User manual

DME PROCESSOR PACK
MVE-8000A-C
OPERATION MANUAL [English]
1st Edition (Revised 1)
MKE-8020A MKE-8021A MKE-8040A HK-PSU02
MULTI FORMAT DME PROCESSOR
MVE-8000A

2
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
THIS APPARATUS MUST BE EARTHED.
Um Feuergefahr und die Gefahr eines
elektrischen Schlages zu vermeiden, darf
das Gerät weder Regen noch Feuchtigkeit
ausgesetzt werden.
UmeinenelektrishenSchlag zu vermeiden,
darf das Gehäuse nicht geöffnet werden.
Überlassen SieWartungsarbeiten stets nur
qualifiziertem Fachpersonal.
DIESES GERÄT MUSS GEERDET
WERDEN.
Afin d’éviter tout risque d’incendie ou
d’électrocution, ne pas exposer cet
appareil à la pluie ou à l’humidité.
Afin d’écarter tout risque d’électrocution,
garder le coffret fermé. Ne confier
l’entretien de l’appareil qu’à un personnel
qualifié.
CET APPAREIL DOIT ÊTRE RELIÉ À LA
TERRE.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: THIS WARNING IS APPLICABLE FOR USA
ONLY.
If used in USA, use the UL LISTED power cord specified
below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration)
Cord Type SJT, three 16 or 18 AWG wires
Length Minimum 1.5 m, Less than 2.5 m (8 ft 3 in)
Rating Minimum 10 A, 125 V
Using this unit at a voltage other than 120V may require the
use of a different line cord or attachment plug, or both. To
reduce the risk of fire or electric shock, refer servicing to
qualified service personnel.
WARNING: THIS WARNING IS APPLICABLE FOR OTHER
COUNTRIES.
1. Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
2. Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Voltage,
Ampere).
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please consult a qualified service
personnel.
AVERTISSEMENT: CET AVERTISSEMENT EST VALABLE
POUR LES AUTRES PAYS.
1. Utiliser un cordon d’alimentation approuvé (conducteur
d’alimentation 3 âmes)/connecteur d’appareil/prise avec
contacts de mise à la terre conforme aux règles de sécurité
de chaque pays si applicable.
2. Utiliser un cordon d’alimentation approuvé (conducteur
d’alimentation 3 âmes)/connecteur d’appareil/prise
conforme aux valeurs nominales (tension, ampérage)
correctes.
S’adresser à un personnel de service qualifié pour toute
question concernant l’emploi du cordon d’alimentation/
connecteur d’appareil/prise ci-dessus.
WARNUNG: DIESE WARNUNG GILT FÜR ANDERE
LÄNDER.
1. Verwenden Sie Netzkabel(dreiadrig), Geräteanschlüsse
und Netzkabelstecker mit Masseleitung, die den
Sicherheitsrichtlinien des jeweiligen Landes entspricht.
2. Verwenden Sie Netzkabel (dreiadrig), Geräteanschlüsse
und Netzkabelstecker mit Masseleitung, die den vor Ort
herrschenden Spannungsanforderungen (Spannug,
Stromstärke) entsprechen.
Bei Frage über die Eignung und Sicherheit von Netzkabeln
(dreiadrig), Geräteanschlüssen und Netzkabelsteckern
wenden Sie sich bitte an einen qualifizierten Electrotechniker.
WARNING
WARNUNG
AVERTISSEMENT

3
For the customers in the USA
This equipment has been tested andfound to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipmentin a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own
expense.
You are cautioned that any changes or modifications not
expressly approved in this manualcould void your authority to
operate this equipment.
The shielded interface cable recommended in this manual
must be used with this equipment in order to comply with the
limits for a digital device pursuant to Subpart B of Part 15 of
FCC Rules.
(MKE-8020A/8021A/8040A, HK-PSU02 only)
This devicecomplies withpart 15of theFCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
For customers in Canada (MKE-8020A/8021A/8040A, HK-
PSU02 only)
This Class A digital apparatus complies with Canadian ICES-
003.
Pour les utilisateurs au Canada (MKE-8020A/8021A/
8040A, HK-PSU02 uniquement)
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
For the customers in Europe (MVE-8000A only)
This product with the CE marking complies with both the EMC
Directive (89/336/EEC) and the Low Voltage Directive (73/23/
EEC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the
following European standards:
• EN60950: Product Safety
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).
Für Kunden in Europa (nur MVE-8000A)
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die
EMV-Richtlinie (89/336/EWG) sowie die
Niederspannungsrichtlinie (73/23/EWG) der EG-Kommission.
Angewandte Normen:
• EN60950: Sicherheitsbestimmungen
• EN55103-1: Elektromagnetische Verträglichkeit
(Störaussendung)
• EN55103-2: Elektromagnetische Verträglichkeit
(Störfestigkeit),
für die folgenden elektromagnetischen Umgebungen: E4
(kontrollierter EMV-Bereich, z.B. Fernsehstudio)
Pour les clients européens (MVE-8000A uniquement)
Ce produit portant la marque CE est conforme à la fois à la
Directive sur la compatibilité électromagnétique (EMC) (89/
336/CEE) et à la Directive sur les basses tensions (73/23/
CEE) émises par la Commission de la Communauté
européenne.
La conformité à ces directives implique la conformité aux
normes européennes suivantes:
• EN60950: Sécurité des produits
• EN55103-1: Interférences électromagnétiques (émission)
• EN55103-2: Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans l’environnement
électromagnétique suivant: E4 (environnement EMC contrôlé
ex. studio de télévision).
For the customers in Europe (MKE-8020A/8021A/8040A,
HK-PSU02 only)
This product with the CE marking complies with the EMC
Directive (89/336/EEC) issued by the Commission of the
European Community.
Compliance with this directive implies conformity to the
following European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following
Electromagnetic Environment: E4 (controlled EMC
environment, ex. TV studio).
Für Kunden in Europa (nur MKE-8020A/8021A/8040A, HK-
PSU02 only)
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die
EMV-Richtlinie (89/336/EWG) der EG-Kommission.
Angewandte Normen:
• EN55103-1: Elektromagnetische Verträglichkeit
(Störaussendung)
• EN55103-2: Elektromagnetische Verträglichkeit
(Störfestigkeit),
für die folgenden elektromagnetischen Umgebungen: E4
(kontrollierter EMV-Bereich, z.B. Fernsehstudio)

4
Pour les clients européens (MKE-8020A/8021A/8040A,
HK-PSU02 uniquement)
Ce produit portant la marque CE est conforme à la Directive
sur la compatibilité électromagnétique (EMC) (89/336/CEE)
émise par la Commission de la Communauté européenne.
La conformité à cette directive implique la conformité aux
normes européennes suivantes:
• EN55103-1: Interférences électromagnétiques (émission)
• EN55103-2: Sensibilité électromagnétique (immunité)
Ce produit est prévu pour être utilisé dans l’environnement
électromagnétique suivant: E4 (environnement EMC contrôlé
ex. studio de télévision).
Periodic inspections
To guarantee safe long-term operation, periodic inspections
are recommended. Please contact your Sony representative
for detailed information about the content and cost of periodic
inspections.

5
Table of Contents
Table of Contents
Overview ...............................................................................6
Features......................................................................................6
Overview of the MVE-8000A-C Components..........................6
Location and Function of Parts...........................................7
Front Panel................................................................................ 7
Rear Panel................................................................................. 8
Example System Configuration (MKE-8020A Installed)..10
MVS-8000/8000A System Configuration.............................. 10
Flow of Video Signals............................................................ 11
Example System Configuration (MKE-8021A Installed)..12
MVS-8000/8000A System Configuration.............................. 12
Flow of Video Signals............................................................ 13
Power Supply Unit Status Indicator..................................14
Specifications.....................................................................15
MVE-8000A Multi Format DME Processor ...........................15
MKE-8020A MVS Interface Board.........................................15
MKE-8021A Input/Output Board............................................16
MKE-8040A Effects Board.....................................................16
HK-PSU02 Power Supply Unit...............................................16

6Overview
Overview
The Sony MVE-8000A-C DME Processor Pack is a
multifunction digital video effects unit for use in a system
configured around an MVS-8000/8000A Multi Format
Switcher System.
The MVE-8000A-C is a generic name of the DME
processor unit having option boards installed in it.
Features
Multi format support
This unit supports both HDTV and SDTV signal formats,
which can be easily selected from the center control panel
for the MVS-8000/8000A system without exchanging
expansion boards. The wide range of supported signal
formats allows the unit to be used in many different video
production environments. The following signal formats
are supported.
• SDTV formats: 480i/59.94, 576i/50
• HDTV formats: 1080i/50, 1080i/59.94, 1080i/60,
1080p/23.976sF, 1080p/24sF, 1080p/25sF, 1080p/
29.97sF, 1080p/30sF, 720p/59.94
Rich variety of effects
The unit supports a wide variety of effects and functions
such as 3D linear transforms (including expand and
reduce) and borders. The effects and functions supported
are as follows.
• 3D linear transforms (expand, reduce, move, rotate)
• Border / Crop
• Defocus / Blur
• Multi-move
• Color modifiers (sepia, monochrome, negative,
posterization, solarization, contrast)
•Mosaic
• Freeze
• Lighting
•Trail
• Background
• Graphics display
• Drop shadow(2-channel effect)
• Combiner
• Brick (3-channel effect)
Up to four DME channels in a single unit
DME boards can be installed to enable up to four
independent DME channels in a single unit, for space
savings and energy efficiency. Because there are multiple
internal channels, up to 4-channel effects can be applied
without making any special connections.
Linked operation with switcher processor
This unit is connected to the MVS-8000/8000A Multi
Format Switcher Processor by a special interface, which
allows DME wipes, processed keys and a wide variety of
other DME effects to be used as if they were switcher
functions. All DME operations can be controlled from the
MVS-8000/8000A system’s center control panel.
Optional backup power supply
Installation of an optional HK-PSU02 Power Supply Unit
provides backup power in addition to the power supply
unit supplied as standard equipment. This reduces the risk
of power trouble and increases the reliability of live
broadcast systems.
Overview of the MVE-8000A-C
Components
MVE-8000A Multi Format DME Processor
This is a cabinet (size: EIA 2RU) in which to install option
boards to provide multi-format DME processing
capabilities.
The option boards are as follows.
a)At least one of either set is required.
b)At least one board is required.
MKE-8020A MVS Interface Board
This board provides a special videosignal interface for the
MVS-8000/8000A Multi Format Switcher Processor.
MKE-8021A Input/Output Board
This boardenables inputand output of video signals via an
SDI interface.
MKE-8040A Effects Board
This board enables 2-channel DME effects. Up to two
boards can be installed to provide 2-channel DME effects.
HK-PSU02 Power Supply Unit
A backup power supply unit. By installing one backup unit
in the MVE-8000A, you can back up the system’s power
supply.
Optional accessories
RMM-10 Rack Mount Kit
Board name Maximum installable number of boards
MKE-8020A 1 set a)
MKE-8021A 1 set a)
MKE-8040A 2 boards b)

7
Location and Function of Parts
Location and Function of Parts
Front Panel
Power A, B switches and status indicators
The POWER switches turn the unit on and off. The unit is
powered on when the POWER switches are onthe “?”side,
and powered off when the POWER switches are on the
“a” side. The status indicators lightin green when the unit
is powered on.
Depending on the system’s configuration when shipped,
there may be no optional HK-PSU02 Power Supply Unit
installed. In this case, the only available POWER switch is
A (there is no switch B).
The unit is powered on when either of the two POWER
switches (A or B) is turned on.
With an HK-PSU02 unit installed, the system continues to
function normally as long as either of the two power
supply units is operating normally.
Caution
When installing the HK-PSU02 in your unit, be sure to
contact your Sony service representative.
Note
If a status indicator does not light when you turn aPOWER
switch on, there may be a fault in the power circuits. Turn
the POWER switch off and contact your Sony service
representative.
POWER A
POWER B
POWER A, B switches and status indicator

8Location and Function of Parts
Rear Panel
aSWITCHER (switcher I/O) A and B connectors
(MDR 68-pin) (MKE-8020A)
Connect with the supplied special cable to the DME 1A
and 1B connectors of the MVS-8000/8000A Multi Format
Switcher Processor.
Each connector handles two channels of video signal input
and output. Therefore, when this unit is configured for one
or two channels (with one MKE-8040A board installed),
you do not need to connect the SWITCHER B connector.
If you are connecting a second MVE-8000A Multi Format
DME Processor to the MVS-8000/8000A, connect the
SWITCHER A and B connectors on the second processor
to the DME 2A and DME 2B connectors on the MVS-
8000/8000A.
aV, K IN/OUT (video and key input and output)
connectors (BNC type) (MKE-8021A)
Used for SDI interface input and output of video signals
between this unit and the switcher or external video
devices.
REMOTE1 GPI
CTRLDATA
REF IN
- AC IN A
- AC IN B
U
SWITCHER ASWITCHER B
REMOTE3
REMOTE2
REMOTE4 GPI 2
REMOTE1 GPI
CTRLDATA
REF IN
-AC IN A
-AC IN B
U
REMOTE3
REMOTE2
REMOTE4 GPI 2
IN
V1 K1 V2 K2 K4V3 K3 V4
1234
OUT
V1 K1 V2 K2 K4V3 K3 V4
MONI OUT
2- AC IN A and B connectors
7CTRL connector
8DATA connector
1SWITCHER A and B connectors
6REMOTE 1 to 4 connectors
4GPI and GPI2
connectors
3Uterminal
This figure shows the rear panel when one MKE-8020A is installed in the unit.
9REF IN connectors
1V, K IN/OUT connectors
2- AC IN A and B connectors
7CTRL connector
8DATA connector
6REMOTE 1 to 4 connectors
4GPI and GPI2 connectors
3Uterminal
5MONI OUT connectors
9REF IN connectors
This figure shows the rear panel when one MKE-8021A is installed in the unit.

9
Location and Function of Parts
b-AC IN (AC power input) A and B connectors (3-
pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cord.
cU(signal ground) terminal
Connect to the system ground.
dGPI (General Purpose Interface) and GPI2
connectors (D-sub, 25-pin)
Connect to external devices for input and output of trigger
signals. Up to sixteen inputs and sixteen outputs are
possible, with input and output conditions set on the center
control panel.
eMONI OUT (monitor output) connectors (BNC
type) (MKE-8021A)
Used to output system channel video keys and graphics to
a monitor.
fREMOTE 1 to 4 connectors (D-sub 9-pin, RS-
422A)
Connect to control this unit from a BVE-9100 or other
editing control system.
gCTRL (control) connector (RJ-45)
Connect to an Ethernet switch*.
The MVS-8000/8000A Multi Format Switcher Processor
and the MVS-8000/8000A system’s center control panel
are connected in the same way to the Ethernet switch to
form a network for exchange of signals between the
devices.
This network is used primarily to control the various
devices from the center control panel.
* Ethernet is a trademark of XEROX Corporation.
For information about Ethernet switches that can be used in an MVS
system, contact your Sony service representative.
For detailed information about setting up the Ethernet
switch, refer to the documentation supplied with the
switch.
For more information about Ethernet switch connectors,
see “MVS-8000/8000A System Configuration” on page
10.
hDATA connector (RJ-45)
Connect to an Ethernet switch.
The MVS-8000/8000A Multi Format Switcher Processor
and the MVS-8000/8000A system’s center control panel
are connected in the same way to the Ethernet switch to
form a network for exchange of signals between the
devices.
This network is used primarily for exchange of various
types of data (key frame effects, snapshots, etc.).
Caution
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following ports.
• CTRL connector
• DATA connector
Follow the instructions for the above ports.
iREF IN (reference video signal input) connectors
(BNC type)
Ifyouwishtosynchronizethisunitto anexternalreference
signal, input the reference signal. For an HDTV system,
input an HD tri-level sync signal, black burst signal, or
analog sync signal. For an SDTV system, input a black
burst signal or analog sync signal.
The two connectors have a loop-through configuration.
Signal input to one connector can be output from the other
connector. If you will not be using the loop-through
output, be sure to terminate the unused connector with the
supplied 75Ωterminator.

10 Example System Configuration (MKE-8020A Installed)
Example System Configuration (MKE-8020A Installed)
MVS-8000/8000A System Configuration
CTRL
DME 1ADME 1B
SWITCHER B SWITCHER A
CTRL
CTRL
PERIPH
PERIPH
DATA
DATA
DATA
Reference video signal b)
BVE-9100 Editing
Control System
Ethernet switch a)
MVE-8000A-C DME
Processor Pack
MKS-8010A System
Control Unit
Reference video signal b)
BKS-R Series
HDS-X Series
Reference
video signal b)
Reference
video signal b)
Cross cable
Cable with BNC
connectors
MVS-8400/8300/8200/8000/8000A-C
Switcher Processor Pack
Ethernet switch a)
VTR DDR Audio Mixer
a)It is recommended that the CTRL and
DATA LAN networks be configured by
connecting separate Ethernet switches
for each LAN.
However, it is also possible to make
connections for both LANs on a single
Ethernet switch.
b)Terminate with the supplied 75Ω
terminators. Terminators are supplied
in the product package.
c) Supplied with MKE-8020A MVS
Interface Board Set.
DCU-2000-C Device
Control Unit Pack
MDR 68-pin cable c)

11
Example System Configuration (MKE-8020A Installed)
Flow of Video Signals
SWITCHER B
DME 1B
MONITOR
OUTPUT 1-8
OUTPUTS 1-48
PRIMARY INPUTS 1-80
DME 1A
SWITCHER A
MVE-8000A-C DME Processor Pack
Reference video signal c)
Monitor
Reference video signal c)
100 to 240 V AC power supply a)
Camera,
VTR,
routing
switcher
100 to 240 V AC power
supply b)
100 to 240 V AC power
supply b)
Monitor
VTR
MVS-8400/8300/8200/8000/8000A-C
Switcher Processor Pack
Cable with BNC connectors AC power supply
Video input signal
Video output signal
Video/key signal
a)For the AC power cord of this unit, refer to “Accessories not
supplied” (see page 15) in this manual.
b) For the AC power cord of the MVS-8000/8000A, refer to
“Accessories not supplied” in the MVS-8400/8300/8200/8000/
8000A-C Operation Manual.
c) Terminate with the supplied 75Ωterminators.
Terminators are supplied in the product package.
d)Supplied with MKE-8020A MVS Interface Board Set.
100 to 240 V AC power
supply b)
100 to 240 V AC power
supply b)
MDR 68-pin cabled)

12 Example System Configuration (MKE-8021A Installed)
Example System Configuration (MKE-8021A Installed)
MVS-8000/8000A System Configuration
CTRL
CTRL
CTRL
PERIPH
PERIPH
DATA
DATA
DATA
Reference video signal b)
BVE-9100 Editing
Control System
Ethernet switch a)
MVE-8000A-C DME
Processor Pack
MKS-8010A System
Control Unit
Reference video signal b)
BKS-R Series
HDS-X Series
Reference
video signal b)
Reference video signal b)
Cross cable
Cable with BNC
connectors
MVS-8400/8300/8200/8000/8000A-C
Switcher Processor Pack
Ethernet switch a)
VTR DDR Audio Mixer
DCU-2000-C Device Control Unit Pack
a)It is recommended that the CTRL and DATA
LAN networks be configured by connecting
separate Ethernet switches for each LAN.
However, it isalso possible to make connections
for both LANs on a single Ethernet switch.
b)Terminate with the supplied 75Ωterminators.
Terminators are supplied in the product
package.

13
Example System Configuration (MKE-8021A Installed)
Flow of Video Signals
V. K IN
PRIMARY INPUTS
1-80
MONITOR OUTPUTS
1-8
OUTPUTS
1-48
REF IN MONI OUT
V. K OUT
MVE-8000A-C DME Processor Pack
Reference video signal c)
Monitor
Monitor
MVS-8400/8300/8200/8000/8000A-C
Switcher Processor Pack
100 to 240 V AC power supply b)
100 to 240 V AC power supply b)
AC power supply
Reference video signal c)
100 to 240 V AC power supply a)
100 to 240 V AC power supply b)
100 to 240 V AC power supply b)
Video input signal
Video output signal
a)For the AC power cord of this unit, refer to “Accessories not
supplied” (see page 15) in this manual.
b) For the AC power cord of the MVS-8000/8000A, refer to
“Accessories not supplied” in the MVS-8400/8300/8200/8000/
8000A-C Operation Manual.
c) Terminate with the supplied 75Ωterminators.
Terminators are supplied in the product package.

14 Power Supply Unit Status Indicator
Power Supply Unit Status
Indicator
The power supply unit status indicator shows the status of
the power supply unit during operation and when the unit
is powered on. Whenever a power error is detected, it is
reflected immediately by the indicator.
Meaning of status indicator displays
Indicator
color Status Description Steps to take
Green Lit Operating normally −
Red LIt Power supply unit fan
fault Exchange the fan unit
−Not lit Power supply unit
fault Exchange the power unit

15
Specifications
Specifications
The following specifications show the reference
performance for this unit and individual option boards.
Design and specifications are subject to change without
notice.
MVE-8000A Multi Format DME
Processor
General
Power requirements
100 to 240 V AC, 50/60 Hz
Power consumption
2.8 to 1.2 A
Peak inrush current
(1) Power ON, current probe method:
15 A (100 V), 66 A (240 V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1: 50 A
(230 V)
Performance temperature
5ºC to 40ºC (41ºF to 104ºF)
Operating temperature
10ºC to 35ºC (50ºF to 95ºF)
Storage temperature
−20ºC to +60ºC (−4ºF to +140ºF)
Operating humidity
10% to 90%
Dimensions (w/h/d, excluding projections)
440×87.5×520 mm
(17 3/8 × 3 1/2 × 20 1/2inches)
Mass Approx. 16 kg (35 lb 4 oz)
(when equipped with all installable
option boards)
Reference input
REF IN BNC type, 75Ωwith loop-through output
HDTV systems: HD tri-level sync/SDTV
analog black burst/SDTV analog sync
SDTV systems: Analog black burst/
analog sync
Control connectors
CTRL RJ-45
Complies with 100 Base-TX standard
DATA RJ-45
Complies with 100 Base-TX standard
REMOTE 1 to 4D-sub 9-pin, female
Complies with RS-422A standard
Data transfer rate: 38.4 Kbps
GPI, GPI2 D-sub 25-pin, female
TTL inputs: 8
Relay contact outputs: 4
(30 V AC/DC, 0.1 A)
Open collector outputs: 4
AC input
AC IN A, B 3-pin AC connector
System Delay
1 frame (in other than 720p format)
2 frames (in 720p format)
Accessories supplied
75Ωterminator (1)
Operation Manual (1)
Installation Manual (1)
Accessories not supplied
AC power cord (for USA and Canada only) (125 V 10 A
2.4 m (8 ft)) (Part No.: 1-557-377-11)
AC power cord (for Europe only) (250 V 10 A 2.4 m
(8 ft)) (Part No.: 1-782-929-22)
MKE-8020A MVS Interface Board
General
Dimensions (w/d)
278×94 mm
(11×3 3/4inches)
Mass Approx. 1 kg (2 lb 3 oz)
Video signal inputs and outputs
SWITCHER A, SWITCHER B
Connectors MDR 68-pin
Signal format LVDS (special format)

16 Specifications
Accessories supplied
Operation and Installation Guide (1)
(supplied only when product is purchased separately)
MDR 68-pin cables (Part No.:1-823-450-11) (2)
Cable holder (1)
MKE-8021A Input/Output Board
General
Power requirements
12 V DC
Power consumption
Approx. 2 A
Dimensions (w/d)
278×94 mm (11×33/4inches)
Mass Approx. 1 kg
Video signal inputs and outputs
IN V1 to V4, IN K1 to K4, OUT V1 to V4, OUT K1 to
K4, MONI OUT
Connector BNC type
Inputs/Outputs Inputs: 8, Outputs: 12
Signal format HD: SMPTE 292M
SD: SMPTE 259M-C
Signal level 0.8 Vp-p ±10%
Signal transfer rate
HD: 1.5 Gbps
SD: 270 Mbps
Return loss 15dB
Cable length HD: 100 m (5C-FB cable, BELDEN1694
or equivalent)
SD: 200 m (5C-2V cable, BELDEN8281
or equivalent)
Accessories not supplied
Operation and Installation Guide (1) (supplied only when
product is purchased separately)
MKE-8040A Effects Board
Power requirements
12 V DC
Power consumption
Approx. 5 A
Dimensions (w/d)
317×380 mm (12 1/2×15 inches)
Mass Approx. 2 kg (4 lb 6 oz)
Accessories supplied
Operation and Installation Guide (1)
(supplied only when product is
purchased separately)
HK-PSU02 Power Supply Unit
Power requirements
100 to 240 V AC, 50/60 Hz
Power consumption
100 V: 10 A, 240 V: 5 A
Peak inrush current
(1) Power ON, current probe method:
110 A (100 V), 220 A (240 V)
(2) Hot switching inrush current,
measured in accordance with
European standard EN55103-1: 40 A
(230 V)
Output power 12 V DC ±0.5 V
Secondary power supply
Max. 60 A
Dimensions (w/h/d)
94×83×396 mm (33/4×33/8×155/8inches)
Mass Approx. 3 kg (6 lb 9 oz)
Accessories supplied
Operation and Installation Guide (1)
(supplied only when product is
purchased separately)
MDR 68-pin cable

The material contained in this manual consists of information
that is the property of Sony Corporation and is intended solely
for use by the purchasers of the equipment described in this
manual.
Sony Corporation expressly prohibits the duplication of any
portion ofthis manual or the use thereof for any purpose other
thantheoperationormaintenanceoftheequipmentdescribed
in this manual without the express written permission of Sony
Corporation.

SonyCorporation
B&PCompany
Printed in Japan
2004.07.13
©2004
MVE-8000A
(SY)
3-855-821-02 (1) Printed on 100% recycled paper
http://www.sony.net/