Sony KP 53HS10 User manual

WARNING
To prevent fire or shock
hazard, do not expose the TV
to rain or moisture,
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
'RISQUEDECHOCELECTR_QUE,
NEPASOUVRIR
PRECAUCION
RfESGO DE CHOQUE ELECTRfCO
NO ABRIR
.CALTrlO_/:TO REDUCE THE RISKOF ELECTRICSHOCK,
,DO NOr REMOVECOVER(OR BACK),
NO USER-SERVICEABLEPARTSINSIDE,
|EFERSERVICINGTO QUALIFIEDSERVICEPERSONNEL,
AThis symbolisintended to alertthe usertothe
presenceof uninsulated=dangerousvoltage"
withinthe product'senclosurethatmay be of
sufficientmagnitude to constituteariskof
electricshockto persons.
//_ This symbolisintendedto alert the userto the
presenceof importantoperatingand
maintenance(servicing)instructionsin the
literature accompanyingthe appliance,
CAUTION
Topreventelectricshock,do notuse thispolarizedAC
plugwithan extensioncord,receptacleor otheroutlet
unlessthe blades can be fully insertedtopreventblade
exposure.
CAUTION
When usingTV games, computers,and similarproducts
withyour projectionTV, keep the brightness and contrast
functions at low settings, if afixed (non-moving)patternis
left onthe screen for long periods of timeespecially at a
highbrightnessor contrastsetting,the image can be
permanently imprintedonto the screen. These types of
imprintsare notcovered by yourwarranty because they
are the resultof misuse.
Note on Caption Vision
Thistelevisionreceiverprovidesdisplayoftelevision
closedcaptioninginaccordancewith§15.t19 oftheFCC
rules.
Note on convergence adjustment
Before you use your projectionTV, make sure to adjust
convergence.Fordetails,see page 24.
Note to CATV system installer
This reminder isprovidedto call the CA'I'Vsystem
installer'sattention to Article820-40 ofthe NEC that
providesguidelinesfor proper groundingand, in particular,
specifiesthatthe cable groundshall be connectedto the
groundingsystemofthe building,as closetothe pointof
cableentry as practical.
Useofthistelevisionreceiverfor otherthanprivate viewing
of programsbroadcaston UHF or VHF ortransmittedby
cable companiesfor the use ofthe general publicmay
require authorizationfrom the broadcaster/cablecompany
and/or programowner.
NOTIFICATION
Thisequipment has been tested and found to comply with
the limits foraClass Bdigital devicepursua_ to Part 15 of
the FCC Rules. These limitsare designedto provide
reasonable protectionagainst harmful interferencein a
residentialinstallation.Thisequipment generates, uses,
and can radiateradiofrequency energyand, ifnotinstalled
and used in accordancewith the instructions,may cause
harmful interferencewith radio oommur_ications.However,
there is noguarantee that interferencewill not occurin a
particular installation.Ifthis equipmentdoes cause
harmful interferenceto radio ortelevisionreception,which
can be determined by turningthe equipmentoff and on,
the user isencouragedto try tocorrectthe interferenceby
one or moreofthe following measures:
• Reorient or relocatethe receivingantennas.
• Increasethe separation between the equipmentand
receiver.
•Connect the equipment intoan outleton a circuit
differentfromthatto whichthe receiveris connected.
•Consultthe dealer or an experiencedradio/lV
technicianfor help.
Youare cautionedthat any changesor modifications
notexpresslyapproved in thismanual couldvoid your
authorityto operate thisequipment.
This document is for the remotecontrolRM-YgO2
MODELS: KP-53HS10, KP-6t HSt0
Please keep thisnoticewith the instructionmanual.
Corporation has determined that this
productmeels the ENERGY STAR
guidelinesfor energy efficiency.
ATTENTION
Pour pr_venirles chocs _lectnques, ne pas utillsercette
fichepo{arisd,eevec un prolongateur,une prise de courant
ou une autre sortiede courant, saul si lee lames peuvent
tre inser_es _ fond sans en laisser aucune partie
decouvert.
Owner's Record
The model and serial numbersare locatedat the rear of
the projectionTV, belowthe Sony logo,onthe sticker,and
also onthe TV box (whitelabel). Record these numbers in
the spaces providedbelow. Refer tothem whenever you
call upon your Sony dealer regardingthis product.
Model No.
Serial No.

Remote d
For a detailed e.\planation of most buttons, see
"'Watching the TV" on page 25.
SLEEP
(page 26)
VTRI/2/3/
DVD/MDP
switch
(page 53)
VCR/DVD/--
MDP
operation
buttons
(page54)
CODE SET-
(pages53,
55)
MTS
(page 35)
MUTING
(page 25)
SYSTEM
TV/DSS/
PICTURE
(page 34)
(pages 26, 55)
(page 26)
JUMP-- I
(page 25) L
MENU
(page 33)
VOL +/-_
(page 25)
RESET
(pages 35, 36)
SONY
I'rvl
POWER
(pages 25, 55)
(pages 25, 55)
CHANNEL INDEX
(pages 28 - 32)
_O
(page 26)
ANT
(page 25)
_0-9 buttons
(page 25)
ENTER
(pages 25, 53)
+/-
(page25)
Joystick
(page 22)
Getting to know the
buttons on the remote
control
Names of the buttons on the remote
control are presented in different
colors to represent the available
functions.
Button color
Transparent:Press to select the
component you want to control;
e.g. VTR (VCR)/MDP/DVD
Player, DBS (Direct Broadcast
Satellite)/CABLE, or projection
TV.
Green :B utton s relevant to power
operations, like turning the
projection TV, DBS/CABLE, or
VTR (VCR)/MDP/DVD Player
on or off
Label color
White:TV/VTR (VCR)/MDP/
DVD Player/DBS (Direct
Broadcast Satellite)/CABLE
operation buttons
Yellow:PIP, P&p, and CHANNEL
INDEX operation buttons
BlUetDBS operation buttons
PinR:DVD Player operation
buttons
* The SYSTEM OFF button does not function with this projection TV.

Table of Contents
Before You Begin
Welcome! ........................ 1
Using this Manual ................. 2
Precautions ....................... 2
Important Safeguards .............. 3
Installing and Connecting
the Projection TV
Carrying Your Projection TV .............. 6
Installing the Projection TV ............... 6
Connector Types ....................... 6
Making Connections .................... 7
Connecting Directly to a Cable or an
Antenna ....................... 7
Connecting a Cable Box ............ 8
Connecting an Antenna/Cable TV
System to a VCR ................ 9
Connecting a VCR and Projection TV
to a Cable Box ................. 10
Connecting a DTV (Digital Television)
Receiver ...................... 1I
Connecting a DBS (Direct Broadcast
Satellite) Receiver .............. 13
Connecting a DBS (Direct Broadcast
Satellite) Receiver and VCR ...... 14
Connecting a Camcorder .......... 15
Connecting Two VCRs for Tape
Editing ....................... 16
Connecting a DVD Player With
S Video or Composite Video Output
Connectors ................... 17
Connecting a DVD Player With
Component Video Output
Connectors ................... 18
Connecting an AV Receiver ........ 19
Connecting an Audio System ....... 20
Connecting an Amplifier That Supports
Dolby Pro Logic Decoder ........ 21
Basic Set Up
Using the Remote Control ............... 22
Setting Up the Projection TV
Automatically ....................... 23
Adjusting the Convergence Automatically
(FLASH FOCUS) ................... 24
Using Your New Projection
TV
Watching the TV ...................... 25
Watching Digital TV ................... 27
Watching Two Programs at One Time --
PIP ............................... 28
Watching Two Programs at One Time --
P&P (Twin View TM) ................. 29
Using CHANNEL INDEX .............. 31
Adjusting Your SET UP
(menus)
Learning Menu Selection ............... 33
[_]Using the VIDEO Menu ............. 34
d_ Using the AUDIO Menu .............. 35
(_) Using the TIMER Menu ............. 36
1_ Using the CHANNEL SET UP Menu... 37
Setting and Selecting FAVORITE
CHANNEL ........................ 39
Setting FAVORITE CHANNEL
manually ..................... 39
Resetting FAVORITE CHANNEL
choices ...................... 39
Using FAVORITE CHANNEL ..... 40
Using the SET UP Menu ............. 40
Using the PARENTAL CONTROL
Feature ............................ 43
Activating the PARENTAL CONTROL
feature ....................... 43
Selecting aCustom Rating in
U.S.A ........................ 45
Selecting a Custom Rating in
Canada ...................... 48

Changing the Password ............ 49
What the Ratings Mean ................. 50
Ratings in U.S.A ................. 50
Ratings in Canada ................ 51
Additional Operations
Operating Video Equipment] ............. 53
Setting the Manufacturer's Code .... 53
Operating video equipment ......... 54
Operating a Cable Box or DBS Receiver .... 55
Setting the Manufacturer's Code .... 55
Operating a cable box or DBS
receiver ...................... 55
Additional Information
Troubleshooting ...................... 56
Specifications ......................... 59
Index ................................ 60
Welcome!
Thank you for purchasing the Sony Color Rear
Video Projection TV. This manual is for models
KP-53HS10 and KP-61HSI0.
Model KP-53HSI0 is used for illustration
purposes.
The features you will enjoy include:
• "1080i Capable," enabling you to receive the 1080i,
4801oand 480i digital TV formats (except for 720p
format). By using the VIDEO 5 (DTV) 1N jacks,
you can connect a DTV (digital television) receiver
to view DTV programs.
The VIDEO 5 (DTV) IN jacks also function as R/
G/B connectors with SYNC signal (HD/VD), but
are not compatible with a computer's 5BNC video
output connectors.
• PARENTAL CONTROL, enabling you to block
programs that are unsuitable for your children.
• DRC (Digital Reality Creation), a technology
unique to Sony, allowing you to obtain a finer, more
detailed picture with four-times higher density than
the conventional NTSC picture. (not available for
input from the VIDEO 5 (DTV) IN jacks)
• MID (Multi Image Driver), a newly developed
device, allowing you to enjoy the following thatures
and, at the same time, to use your projection TV
easily. (not available for input from the VIDEO 5
(DTV) IN jacks)
-- Picture & Picture (P&P) with zoom-in function
(Twin ViewTM) _I!
-- Picture-in-Picture (PIP) _,
CHANNEL INDEX. allowing you to view and
choose from twelve programs
-- FAVORITE CHANNEL, allowing you to view
and choose from eight of your favorite channels
• FLASH FOCUS, allowing you to adjust qt_=.
convergence automatically.
• Two Y/PB/PR inputs for DVD Player connection
(480p format capability is on the VIDEO 5 (DTV)
IN jacks).
• Four AUDIONIDEO/S VIDEO inputs.
TruSurround, SRS and the COY symbol are
trademarks of SRS Labs, Inc. in the United States
and selected foreign countries.
TruSurround and SRS technology is incorporated
under license from SRS Labs, Inc.
Manufactured under license from Dolby
Laboratories Licensing Corporation. "Dolby," and
the double-D symbol 130 are trademarks of Dolby
Laboratories Licensing Corporation.

Using this Manual
We recommend that you carefully review the
contents of the following four sections in the order
provided to ensure that you fully understand the
operation of your new projection TV.
1InstallingandConnectingthe ProjectionTV
This section guides you through your initial set
up. It shows you how to install your projection
TV, to connect your new components and to
connect to the antenna and cable.
2Basic Setup
This section teaches you the basic skills needed
to operate your new projection TV, including
Easy Set Up. It shows you how to operate the
remote control's special functions.
3 UsingYourNew Projection TV
This section shows you how to begin using
your new projection TV. It shows you how to
use your remote control's features.
4AdjustingYourSet Up(menus)
This section teaches you how to access on-
screen menus and adjust your projection TV's
settings.
Instructions in this manual are written for the remote
control. Similar controls may be fimnd on the
projection 71/console.
Precautions
Safety
•Operate the projection TV only on 120 V AC.
• The plug is designed, for safety purposes, to fit into
the wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact your
dealer.
• If any liquid or solid object should tall inside the
cabinet, unplug the projection TV immediately and
have it checked by qualified service personnel
before operating it further.
• If you will not be using the projection TV for
several days, disconnect the power by pulling the
plug itself. Never pull on the cord.
For details concerning safety precautians, see
'lmpo "ta it Safeguards" on page 3.
Note on cleaning
Clean the cabinet of the projection TV with a dry
soft cloth. To remove dust from the screen, wipe it
gently with a soft cloth. Stubborn stains may be
removed with a cloth slightly dampened with
solution of mild soap and warm water. Never use
strong solvents such as thinner or benzine for
cleaning.
If the picture becomes dark after using the
projection TV for a long period of time, it may be
necessary to clean the inside of the projection TV.
Consult qualified service personnel.
Installing
• To prevent internal heat buildup, do not block the
ventilation openings.
• Do not install the projection TV in a hot or humid
place, or in a place subject to excessive dust or
mechanical vibration.
• Avoid operating the projection TV at temperature
below 5°C (4I°F).
•lfthe projection TV is transported directly from a
cold to a warm location, or if the room temperature
changes suddenly, the picture may be blurred or
show poor color. In this case, please wait a few
hours to let the moisture evaporate before turning
on the projection TV.
• To obtain the best picture, do not expose the screen
to direct illumination or direct sunlight. It is
recommended 'touse spot lighting directed down
from the ceiling or to cover the windows that face
the screen with opaque drapery. It is desirable to
install the projection TV in a room where the floor
and wails are not of a reflective material.
2

Important Safeguards
For your protection, please read these instructions
completely, and keep this manual for future
reference.
Carefully observe and comply with all warnings,
cautions and instructions placed on the set, or
described in the operating instructions or service
manual.
WARNING
To guard against injury, the following basic safety
precautions should be observed in the installation,
use, and servicing of the set.
Use
Power Sources
This set should be operated
only from the type of power
source indicated on the
serial/model plate.
If you are not sure of the
type of electrical power
supplied to your home, consult your dealer or local
power company. For those sets designed to operate
from battery power, refer to the operating
instructions.
Grounding or Polarization
This set is equipped with a polarized AC power
cord plug (a plug having one blade wider than the
other), or with a three-wire grounding type plug (a
plug having a third pin for grounding).
Follow the instructions below:
For the set with a the possibility of an internal malfunction thatpolarized AC power could create a fire hazard.
cord plug Object and Liquid _'
EntryThis plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to-fit, contact
your electrician to have a suitable outlet installed.
Do not defeat the safety purpose of the polarized
plug by forcing it in.
Alternate Warning
For the set with athree-wire grounding
type AC plug
This plug will only fit into a grounding-type power
outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your
electrician to have a suitable outlet installed. Do
not defeat the safety purpose of the grounding
plug.
Never push objects of any
kind into the set through the
cabinet slots as they may
touch dangerous voltage
points or short out parts that
could result in a fire or
electric shock. Never spill
liquid of any kind on the set.
Attachments
Do not use attachments not
recommended by the
manufacturer, as they may
cause hazards.
Overloading
Do notoverload wall outlets,
extension cords or
convenience receptacles
beyond their capacity, since
this can result in fire or
electric shock.
Always tum the set off when
it is not to be used. When the
set is left unattended and
unused for long periods of
time, unplug it from the wall
outlet as a precaution against
Cleaning
Unplug the set from the wall
outlet before cleaning or
polishing it. Do not use
liquid cleaners or aerosol
cleaners. Use a cloth lightly
dampened with water for
cleaning the exterior of the
set.
(continued)
3

s_ _'! ,*_.
If a snapping or popping
'_ sound from a projection TV
set is continuous or frequent
while the projection TV is
operating, unplug the
projection TV and consult
your dealer or service
.i technician. It is normal for
some projection TV sets to
make occasional snapping or popping sounds,
particularly when being turned on or off.
Installation
Water and Moisture
Do not use power-line
operated sets near water--
for example, near a bathtub,
washbowl, kitchen sink, or
laundry tub, in a wet
basement or near a
swimming pool, etc.
Accessories
Do not place the set on an
unstable cart, stand, table or
shelf. The set may fall,
causing serious injury to a
child or an adult, and serious
damage to the set. Use only a
cart or stand recommended
by the manufacturer for the
specific model of projection
TV.
®An appliance and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may cause
the appliance and cart
combination to overturn.
Ventilation
The slots and openings in the cabinet and in the
back or bottom are provided for necessary
ventilation. To ensure reliable operation of the set,
and to protect it from overheating, these slots and
openings must never be blocked or covered.
®, - Never cover the slots and
openings with a cloth or
other materials.
- Never block the slots and
openings by placing the set
on a bed, sofa, rug or other
similar surface.
- Never place the set in a
confined space, such as a
bookcase, or built-in cabinet
unless proper ventilation is
provided.
- Do not place the set near or
over a radiator or heat
register, or where it is
exposed to direct sunlight.
Antennas
Power-Cord Protection
Do not allow anything to rest
on or roll over the power
cord, and do not place the set
where the power cord is
subject to wear or abuse.
Outdoor Antenna Grounding -- If an
outdoor antenna is installed, follow the precautions
below.
An outdoor antenna system should not be located
in the vicinity of overhead power lines or other
electric light or power circuits, or where it can
come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR
ANTENNA SYSTEM, EXTREME CARE
SHOULD BE TAKEN TO KEEP FROM
CONTACTING SUCH POWER LINES OR
CIRCUITS AS CONTACT WITH THEM IS
ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to
provide some protection against voltage surges and
built-up static charges.
Section 810 of the National Electrical Code (NEC)
in USA and Section 54 of the Canadian Electrical
Code in Canada provides information with respect
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and
requirements for the grounding electrode.

Antenna Grounding According to the
NEC -- Refer to section 54-300 of Canadian
Electrical Code for Antenna Grounding.
cla./_-mp_, wireAntennalead-in
Ground \ _'_ Antenna discharge
/_._ _X unit (NEC Section
_'_ ,/_1 810-20)
I I Grounding
r J _ _ _j_ conductors (NEC
__ Section 810-21)
.... _ Ground clamps
Electric service ",_
equipment Power service
grounding electrode
NEC: National system (NEC Art 250
Electrical Code Part H)
Lightning
For added protection for this television receiver
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna. This will prevent damage to the receiver
due to lightning and power-line surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
-When the power cord or
a_,,,-,,,,_ @ plug is damaged or frayed.
he.. LA_. ej_tliel_ pl '_"
//
//
i°/
- If liquid has been spilled
into the set.
- If the set has been exposed
to rain or water.
- If the set has been subject
to excessive shock by being
dropped, or the cabinet has
been damaged.
- If the set does not operate
normally when following the
operating instructions.
Adjust only those controls
that are specified in the
operating instructions.
Improper adjustment of other controls may result
in damage and will often require extensive work by
a qualified technician to restore the set to normal
operation.
- When the set exhibits a distinct change in
performance--this indicates a need for service.
__ ervicing
Do not attempt to service the
set yourself since opening
the cabinet may expose you
to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
_TV SERVICE DEPT,_
Replacement Parts
When replacement parts are required, be sure the
service technician certifies in writing that he has
used replacement parts specified by the
manufacturer that have the same characteristics as
the original parts.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
Safety Check
Upon completion of any
service or repairs to the set,
ask the service technician to
perform routine safety
checks (as specified by the
manufacturer) to determine
that the set is in safe
operating condition, and to
so certify.
When the set reaches the end
of its nsefid life, improper
disposal could result in a
picture tube implosion. Ask
a qualified service technician
to dispose of the set.
6
tll
Ill
¢D
tQ
5"
5

Recommended viewing area
(Vortical) Connector Types
Carrying Your
Projection TV
Carrying the projection TV requires three or more
people•
The projection TV has been equipped with casters
for easy movement on a hard surface• Please move
your projection TV using the casters•
Installing the
Projection TV
Recommended viewing area
(Horizontal)
You may find it necessary to use some of the
following connector types during set up.
Coaxial cable
Standard TV cable and antenna cable
Plug Type
--_ (_ Push into connection•
Screw-on Type
"_ (_ Screw into connection•
S Video cable
High quality video cable for enhanced picture
quality
_ Align guides and
mm_ , •
[_)J push into connection.
Audio/Video cable
--_--€,(_)Pushintoconnection.
Video- Yellow
Audio (Left) - White
Audio (Right) - Red
Some DVD Players are equipped with the
following three video connectors.
Y - Green
PB (CB, Cb or B-Y) - Blue
1_ (Cr, Cr or R-Y) - Red

Composite video cable for a DTV
receiver
--:_1_ _ _) Push into connection.
G/Y - Green
B/PB - Blue
R/PR - Red
HD - Gray
VD - Black
CONTROL S cable
Sony cable for CONTROL S connections. These
features are exclusive to Sony products and allow
greater control of all Sony equipment.
_ _ Push into connection.
RK-G34
(not supplied)
About the CONTROL S IN/OUT
Jacks
To control other Sony equipment with the
projection TV's remote control, connect the
CONTROL S IN jack of the equipment to the
CONTROL S OUT jack on the projection TV with
the CONTROL S cable.
To control the projection TV with a remote control
for another Sony product, connect the CONTROL
S OUT jack of the equipment to the CONTROL S
IN jack on the projection TV with the CONTROL
S cable.
_w0o
÷
Dm
wuf
o- @
Making Connections
The connection you choose will depend on the
cable found in your home. Newer homes will be
equipped with standard coaxial cable (see A);
older homes will probably have 300-ohm twin lead
cable (see B); still other homes may contain both
(see C).
A
(Rear of
•VHF only 75-ohm projectionTV)
coaxial cable VHF/UHF
or
•V.F,O.F
or
•Cable
B
(Rear of
300.ohm twin projection TV)
•VHF only lead cable VHF/UHF
or
UHF only
ior
WF, .F,ntennao noec,or
",t
(con_nue_
7

8
C75-ohm coaxial cable
•VHF _...,_ (Rear of
m projection TV)
and EAC-66 UP/mixer
(not supplied)
•UHF _
300-ohm twin lead cable
Cable or antenna
This is the simplest connection. Connection is
made directly from the cable or antenna to the
projection TV.
(Rear of projection TV)
Cable VHF/UHF
Cab_ andantenna
You may find it convenient to nse the following set
up if your cable provider does not feature local
channels that you are able to receive using an
antenna.
CATV cable
(Rear of
projection TV)
AUX
Antenna cable VHF/UHF
Select Cable or ANT mode by pressing ANT on
the remote control.
Some pay cable TV systems use scrambled or
encoded signals that require a cable box* to view
all channels.
Also, set CABLE to ON in the CHANNEL SET
UP menu. (see page 38) (Rear ot Projection TV)
Cable VHF/UHF
U
IN _'_ OUT
*cable box
Note:
•If you will be controlling all channel selection
through your cable box, you should consider using
the CHANNEL FIX feature. (see "CHANNEL
FIX" on page 38)
Cab_box and cab_
Some pay cable TV systems use scrambled or
encoded signals requiring a cable box* only for
certain channels. (e.g. HBO, SHOWTIME, etc.)
*cable box (Rear of Projection TV)
JAUX
VHF/UHF
CATV cable _""_
(unscrambled channels)
For this set up, you can switch between scrambled
channels (through your cable box), and normal
(CATV) channels by pressing ANT on your remote
control.
Notes:
•You may be able to program your Sony remote
control to operate your cable box. (see "Operating a
Cable Box or DBS Receiver" on page 55)
• During PIP, P&P, CHANNEL INDEX or
FAVORITE CHANNEL viewing, the AUX input
can only be viewed in the main picture.
If you are connecting a cable box through the AUX
input and would like to switch between the AUX
and normal (CATV) input, you should consider
using CHANNEL FIX. (see "CHANNEL FIX" on
page 38)

1
2
3
Attach the coaxial cable from the incoming
cable connection or antenna to IN on the VCR.
Using acoaxial cable, connect OUT on the
VCR to VHF/UHF on the projection TV.
Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the VCR to
AUDIO and S VIDEO IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).
* If your VCR is not equipped with S VIDEO, use
a VIDEO cable (yellow) instead of the S VIDEO
cable.
Note:
•If you are connecting a monaural VCR, connect
only the single audio output to the left (MONO)
input on the projection TV. S VIDEO--
Disconnectall power sourcesbefore making any connections.
(Rear of projection TV)
IN I OUT I
,. @@
g_Ol IVIOEO_
F I • •
.
--VIDEO
--AUDIO-L
--AUDIO-R
VMC-810S/820S
(not supplied)
1
T
YC-15V/30V (not supplied)
VCR
2
I
Coaxial cable
(not supplied)
4UO_R /,_DIO L VICEO S VIDEO
°_0®@ @ v.:._.F Cable/
ou_l®lI Antenna
=0
==
o

10
1Connect the single (input)jack of the splitter to
the incoming cable connection, and connect
the other two (output) jacks (using the coaxial
cable) to IN on the cable box and VHF/UHF
on the projection TV.
2Using a coaxial cable, connect OUT on the
cable box to IN on the VCR.
3Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the VCR to
AUDIO and S VIDEO IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).
* If your VCR is not equipped with S VIDEO, use
a VIDEO cable (yellow) instead of the S VIDEO
cable.
Note:
• To view scrambled channels through the cable box,
select the video input which the cable box is
connected to by pressing TV/VIDEO,
S VIDEO--
=R
g_
Disconnect all power sources before making any connections.
(Rear of projection TV)
IM otrr 6
ivl0cos_wi _ttcT
@@
li ,"
o_n,_g I.w
-- VIDEO
_AUDIO-L *uaoF,,,_,oL',',_-osv,_o
-- AUDIO-R0 @0 @
VMC-810S/820S _" "'@3--_
(not supplied)
1
T
YC-15V/30V (not supplied)
VCR
Coaxial c!ble
(not supplied)
Coaxial cable
(not supplied)
21
Cable/
7_ __ Antenna
oul"il2rll i I_ K--"I
Cable box Splitter
(not supplied)

Before connecting, be sure to read the Operating
Instructions of the DTV receiver.
Connecting a DTV (digital
television) receiver with the G/B/R/
HD/VD jacks
1Attach the coaxial cable from the roof antenna
to VHF/UHF on the DTV receiver.
2Using a composite video cable for DTV
receiver, connect G, B, R, HD and VD of
VIDEO OUT on the DTV receiver to G, B, R,
HD and VD respectively of VIDEO 5 (DTV)
IN on the projection TV.
If the DTV receiver is equipped with the Y/PB/
PR jacks, proceed to step 2 in "Connecting a
DTV (digital television) receiver with the Y/
PB/Pr (component video input) jacks" on page
12.
3
4
5
Using an AUDIO cable, connect AUDIO OUT
on the DTV receiver to AUDIO of VIDEO 5
(DTV) IN on the projection TV (White-
AUDIO Left, Red-AUDIO Right).
Select VIDEO 5 by the TV/V1DEO button.
Select the SET UP menu and set DTV INPUT
to R.G.B. (see "DTV INPUT" on page 43)
Disconnect aftpower sourcesbefore making any connections.
m Z
-0---@
O-1-O
2
1
Roof Antenna
RK-74A (not supplied)
]3
HD
VD
(continued
5"
"D
11

Connecting a DI_ (digital
television) receiver with the Y/P_/
PR (component video Input) Jacks
1Attach the coaxial cable from the roof antenna
to VHF/UHF on the DTV receiver.
2
3
4
5
Using three VIDEO cables, connect Y, PB and
Pr of COMPONENT VIDEO OUT on the
DTV receiver to Y, PB and Pr of VIDEO 5
(DTV) IN on the projection TV.
Using an AUDIO cable, connect LINE OUT
on the DTV receiver to AUDIO of VIDEO 5
(DTV) IN on the projection TV (White-
AUDIO Left, Red-AUDIO Right).
Select VIDEO 5 by the TV/VIDEO button.
Select the SET UP menu and set DTV INPUT
to Y PB PR. (see "DTV INPUT" on page 43)
Note:
•Some DTV receiver terminals may be labeled
differently. If so, connect as follows:
Connect Y (green) to Y.
Connect PB (blue) to Cry,Ch or B-Y.
Connect PR (red) to Cr, C, or R-Y.
m
PB m
PR._
Disconnect all power sourcesbefore making any connections.
-Y
,ll
VMC-10HG
(not supplied)
_i 6 DTV receiver
VHF/dH,
W_Jm
®
AUDIO-R AUDIO-L Roof Antenna
L_K-74A (not supplied)
2

1Connect the cable from the satellite antenna to
the DBS receiver.
2Attach the coaxial cable from the incoming
cable connection or antenna to VHF/UHF on
the projection TV.
3Using AUDIO and S VIDEO cables, connect
AUDIO and S VIDEO OUT on the DBS
receiver to AUDIO and S VIDEO IN on the
projection TV (White-AUDIO Left, Red-
AUDIO Right).
Note:
•To view input from the DBS, select the video input
which the DBS receiver is connected to by pressing
TV/VIDEO on the remote control.
Disconnect all power sourcesbefore making any connections.
(Rear of projection TV) Cable/
,N _OuT_ _ An1 Ir
/
_S-VIDEO
AUDIO-L
-- AUDIO-R
RK-74A (not supplied)
1
Satellite antenna
Antenna cable
1
DBS
. . _
T
YC-15V/30V (not supplied)
==
¢b
o
13

14
1Connect the cable from the satellite antenna to
the satellite receiver.
2Attach the coaxial cable from the incoming
cable connection or antenna to VHF/UHF IN
on the VCR.
3
4
Using a coaxial cable, connect VHF/UHF
OUT on the VCR to VHF/UHF on the
projection TV.
Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the DBS
receiver to AUDIO and S VIDEO IN on the
VCR.
5Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the VCR to
AUDIO and S VIDEO IN on the projection TV
(White-AUDIO Left, Red-AUDIO Right).
* If your VCR or DBS receiver is not equipped
with S VIDEO, use a VIDEO cable (yellow)
instead of the S VIDEO cable.
Note:
• To view input from the DBS or VCR, select the
video input which your DBS receiver or VCR is
connected to by pressing TV/VIDEO on the remote
control.
s
VIDEO--
_vlDr_
_u
.,_
Disconnect all power sources before making any connections.
(Rear of projection TV)
IN IO[IT
YD I
z @@1
AUtO
VIDEO
AUDIO-L
AUDIO-R
AtrX
leo
T
VMC-810S/820S (not supplied)
1
Coaxial cable
(not supplied)
1
ISATI_N_o_E IN VNFIU_
AUOIO R_L VI_O S VIDEO IN
Satellite
antenna
cable
!-
VMC-810S/820S
(not supplied i
LINE AU RAL
3
DBS
YC-15V/30V
(not
supplied)
VCR
lCable!
Antenna
2
YC-15V/30V (not supplied)

Use this connection to view a picture directly from
your camcorder.
1Using AUDIO and S VIDEO* cables, connect
AUDIO and S VIDEO OUT on the camcorder
to AUDIO and S VIDEO IN inside the lower
front panel on the projection TV (White-
AUDIO Left, Red-AUDIO Right**).
2Press VIDEO 2 to select the video inputs from
a camcorder.
* If your camcorder is not equipped with S VIDEO,
use a VIDEO cable (yellow) instead of the S
VIDEO cable.
**If you are connecting a monaural camcorder,
connect only the single audio output to the left
(MONO) input on the projection TV.
Push to open.
Disconnectall power sourcesbefore making any connections.
(Front of projection TV)
S VIDEO
AUDIO-L
AUDIO-R
VMC-810S/820S -
(not supplied)
1
Audio/video
outputs
- YC-15V/30V
(not supplied)
1
Camcorder
8
O'
15

16
SELECT OUT gives you the ability to use a
second VCR to record a program being played by
the primary VCR or to perform tape editing and
dubbing.
1
2
Connect the VCR intended for playback using
the connection instructions on page 9 of this
manual.
Using an AUDIO/VIDEO cable, connect
AUDIO and VIDEO IN on the VCR intended
for recording to AUDIO and VIDEO OUT of
SELECT OUT on the projection TV.
Notes:
• Do not change the input signal while editing
through SELECT OUT.
• When connecting a single VCR to the projection
TV: if VCR LINE OUT is connected to VIDEO IN
on the projection TV, do not connect the SELECT
OUT on the projection TV to the VCR LINE
INPUT (see right). Doing so will cause program
interference and other viewing problems.
•You can select the output signal from SELECT
OUT from the SET UP menu. (see "SELECT
OUT" on page 41 )
Disconnectall power sourcesbefore making any connections.
(Rear of projection TV)
VIDEO4 IWDEOS(OT_
no vo
IN
I'
VCR (for playback) I
I
UH EOLrT
1
VMC-810S/820S
(not supplied)
D .
--VIDEO VIDEO--
--AUDIO-L AUDIO-L--
--AUDIO-R AUDIO-R---
AUX
®
V_F&_F
_o
VCR (for recording)
AUmOR JtlJD40L VlE_O OUT[_
.
VMC-810S/820S
(not supplied)
(Rear of projection TV)
Indicates direction
of signal